测定食品及生物样品中微量锡的消化方法探讨

采用干灰化、硝酸-高氯酸、硝酸-硫酸-高氯酸和用硝酸过氧化氢微波消解4种消化方法消化样品,氢化物发生-原子荧光光谱法测定食品及生物样品中微量锡。方法线性范围为20.0μg.L-1以内,相关系数为0.999 8,经过比较,微波消解和硝酸-硫酸-高氯酸消解方法较理想,回收率分别为98.2%~101.4%和97.4%~102.8%,相对标准偏差分别为2.39%~3.85%和3.25%~3.82%。只测定锡时,微波消解和硝酸-硫酸-高氯酸消解法均可,但如锡与其他微量元素需要同时测定,为避免引入有干扰的硫酸根,以用硝酸-过氧化氢微波消解为好。     

微波消解样品-氢化物发生-原子荧光光谱法测定海贝中硒

海贝样品经硝酸和过氧化氢微波加热消解,用氢化物发生-原子荧光光谱法测定其中硒的含量。使用溶于5g·L~（-1）氢氧化钾溶液中的10g·L~（-1）硼氢化钾溶液与溶液中硒离子反应生成氢化物。试样溶液中加入抗坏血酸消除硝酸的干扰。在优化的试验条件下,硒的质量浓度在600μg·L~（-1）以内与其荧光强度呈线性关系;方法检出...     

磷酸二氢钾浸提-原子荧光光谱法测定土壤中有效硒样品处理

对标准方法NY/T 3420—2019测定土壤中有效硒含量的样品处理方法进行优化。用电热板消解取代微波消解，以三氯化铁取代铁氰化钾，提高盐酸质量分数至20%，对KH₂PO₄浸提-原子荧光光谱法测定土壤中有效硒的样品处理方法进行优化。用硝酸-高氯酸混合酸将浸提液中的硒溶出后，在硫酸存在条件下加热挥发完全，可避免样品溶液中高氯酸钾结晶生成。硫酸因工艺原因含有硒，加入溴化钠加热至无色，重复处理多次可将绝大部分硒去除。经过试验确定硫酸最终质量分数为4%，此条件下硒的加标回收率为96.6%～105.9%。该方法和标准方法NY/T 3420—2019的测定结果经F检验和t检验验证，不具有显著性差异。该方法简化前处理流程，测定结果满足标准质控要求，适合大批量土壤样品测定。     

微波消解–原子荧光光谱法测定植物样品中的砷和硒

建立微波消解-原子荧光光谱法测定植物样品中砷和硒的含量。微波消解后残留的有机颗粒和硝酸等会对测定结果造成影响,因此需要将硝酸除尽。在驱除硝酸过程中加入高氯酸,加热至溶液冒白烟,避免硒挥发损失。该方法砷、硒的检出限分别为6.8,4.0 ng/g(稀释因子40),测定结果的相对标准偏差分别为3.65%,3.52%(n=12),加标回收率分别为94.5%~104.6%,92.2%~98.9%。经过国家一级标准物质验证,该方法准确可靠。     

硫氰酸盐-乙基紫-阿拉伯树胶体系吸光光度法测定痕量硒

在0.50～0.58mol·L~(-1)硫酸溶液中,在阿拉伯树胶存在下,Se(Ⅳ)与硫氰酸盐,乙基紫形成可溶性离子缔合物。此缔合物在波长620nm处有最大吸收,表观摩尔吸光系数(?)为4×10~(?),硒含量在0～4.0μg/25ml范围内服从比耳定律。研究了形成离子缔合物的最佳条件和共存离子的影响,方法用于水样和人发样中痕量硒的测定,结果满意     

硒钼杂多酸—罗丹明B离子缔合物显色反应的研究与应用

研究了在聚乙烯醇分散剂存在下 ,硒 钼酸铵 罗丹明B(RDB)三元缔合物的显色反应。建立了测定硒碘盐中微量硒的新方法。离子缔合物的最大吸收波长为 5 70nm ,表观摩尔吸光系数ε570 =5 .6× 10 5L·mol- 1·cm- 1。在测定条件下 ,硒含量在 0～ 6μg/ 2 5ml范围内符合比耳定律。对于硒碘盐样品的测定 ,RSD≤ 2 .5 % ,结果满意     

微波消解-ICP-MS测定中药材中5种有害元素的研究

比较了密闭容器消解、微波消解两种消解方法的消解效果,并建立了微波消解-电感耦合等离子体质谱(ICP-MS)法测定中药材(CTM)中铜砷镉汞铅等5种有害元素含量的分析方法,对各元素的线性关系良好(r=0.9998~1.0000),检出限为0.005μg/g(Hg)~0.056μg/g(Cu),标准物测定回收率均在84.2%~101%,因其低检出限、高灵敏度,本方法能满足中药材样品质量控制中5种有害元素的测定要求。另外利用本方法对24种中药材中5种有害元素含量进行了测定,结果表明中药材中有害元素含量超标问题严重,必须在生产过程中予以重视。     

湿法消解-原子荧光法测定全血中硒

以全血样品为原料,探讨湿法消解-原子荧光法测定全血中的硒含量。血样经硝酸-高氯酸消解后,用硼氢化钠将硒还原成硒化氢,由氩气载入原子化器,产生的原子荧光强度与试液中硒元素含量在一定范围内呈正比,外标法定量。以消解效率为指标,优化样品的消解条件,测定血中硒在0-10μg/L范围内线性情况良好,相关系数为0.9992,最低检出限为0.143μg/L,相对标准偏差为1.51%-1.58%,平均加标回收率为90.86%-104.62%。血中硒的原子荧光测定法灵敏度高,精密度和稳定性好,可应用于血中硒的生物监测。     

ICP-MS法测定聚酯纤维中TiO2含量

采用湿法和微波法对聚酯纤维样品进行消解,利用电感耦合等离子体质谱联用仪(ICP-MS)对样品中TiO2含量进行了测定,得到湿法消解样品测定值2 857.46μg/g(相对标准偏差为1.08%),微波消解样品测定值2599.21μg/g(相对标准偏差为2.76%).分别测定了两种消解方法的检出限,湿法消解检出限为4.0 ...     

均匀设计和正交设计联用优化ICP法测定铅锌矿石中锌、铜、砷、铁的微波消解条件

采用均匀设计与正交设计联用,优化电感耦合等离子发射光谱法测定铅锌矿石中锌、铜、砷、铁含量的微波消解样品条件。在微波功率为800 W的条件下,以测定结果的回收率和相对标准偏差为指标,对试样量、盐酸和硝酸体积比、微波消解时间、微波消解最高温度4个因素进行均匀设计,并在此基础上选取因素水平范围进行正交试验,优选最佳微波消解条件:称样质量为0.2 g,盐酸和硝酸体积比为3∶1,微波消解时间为45 min,微波消解最高温度为175℃。在该消解条件下进行实验,方法回收率为95.2%～98.6%,测定结果的相对标准偏差为0.10%～0.16%(n=6)。对该实验条件参数进行稳健性试验,结果表明该方法稳定可行。该方法准确、可靠,可用于矿石中锌、铜、砷、铁含量的测定。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.