A ratiometric CdSe/ZnS nanocrystal pH sensor

The development of a reversible chemical sensor based on a CdSe/ZnS nanocrystal (NC) is described. Signal transduction is accomplished by fluorescence resonance energy transfer (FRET) between the NC and a fluorescent pH-sensitive squaraine dye attached to the surface of the NC. The efficiency of FRET, and consequently the relative intensity of NC and dye emissions, is modulated with the pH-dependent absorption cross section of the squaraine dye. The design of a NC sensor based on FRET results in a ratiometric sensor since the emission intensities of dye and NC may be referenced to the isosbestic point between NC and dye emissions. The ratiometric approach allows sensing to be performed, regardless of issues surrounding collection efficiency (scattering environment, light fluctuations, etc.) and dye:NC loadings.     

Excitation dependence of steady-state photoluminescence in CdSe nanocrystal films

The excitonic and deep-level photoluminescence (PL) in CdSe nanocrystal (NC) films (wurtzite type) was studied under continuous-wave excitation as a function of excitation power, temperature, and time of photoaging. It was shown that the intensity-power dependencies are identical for excitonic and deep-level emissions in a wide temperature range. At low temperatures (80-100 K), both emissions were saturated at the laser power used, which generates more than one exciton per nanocrystal. A transition point from the linear to the saturated region was dependent on the temperature, size, and quality of the NCs. A clear inverse dependency between the intensities of excitonic and deep-level emissions was revealed at 80 K over the entire sample area. At room-temperature, the quantum yield dropped significantly and a higher laser power was needed to reach PL saturation. An increase in temperature led to worsening of the reverse dependence between excitonic and deep-level emissions, and at room-temperature, they became uncorrelated. These results can be explained by Auger recombination and also by an increase of nonradiative recombination in the surface states with increasing temperature.     

Spin blockade in the conduction of colloidal CdSe nanocrystal films

The conduction of thin films of n-type CdSe colloidal quantum dots is studied at low temperature and under magnetic field. At medium and high magnetic fields (10 T), the films exhibit positive magnetoresistance consistent with the variable range hopping model. At low magnetic field(<0.3 T) but in the strong electric field regime, there is a narrower magnetoresistance of order 10%-15%. The magnetoresistance shows a strong bias dependence, small and positive at low bias, increasing but still positive at higher bias, and turning negative at the highest bias. A similar behavior has been reported recently for thin film organics. Weak localization effects are ruled out. The explanation for the observations is based on spin blockade relaxed by the hyperfine interaction. The weak magnetoresistance at low bias is attributed to the diffusing paths taken by the hopping electrons. At higher bias, the more directed motion of electrons leads to increasingly positive magnetoresistance due to the more effective spin blockade. At the highest bias, the magnetoresistance becomes negative, which is attributed to the increased exchange interaction associated with the shorter tunneling distance.     

Photoinduced charge transfer between CdSe nanocrystal quantum dots and Ru-polypyridine complexes

In this communication, we demonstrate a new approach to sensitization of Ru-polypyridine complexes by using semiconductor nanocrystal quantum dots (NQDs). When mixed in solution, the complexes functionalized by carboxylic groups adsorb onto the surface of the NQDs. Excitation of NQDs by 400 nm light leads to fast, 5 ps hole transfer from the photoexcited NQDs to the surface-adsorbed complexes. This result indicates that Ru complexes can be sensitized by CdSe NQDs, which opens interesting opportunities for designing new types of photocatalytic materials for solar energy conversion applications. These materials will take advantage of broad size-controlled absorption spectra and large extinction coefficients of NQDs as well as the unique property of NQDs to respond to absorption of a single photon by producing multiple electron-hole pairs.     

Detection of toxic mercury ions using a ratiometric CdSe/ZnS nanocrystal sensor

We have developed a strategy for the ratiometric detection of toxic Hg(2+) ions using a semiconductor nanocrystal energy-transfer donor coupled to a mercury-sensitive "turn-on" dye acceptor. The results demonstrate a new paradigm of toxic metal sensing that resolves the difficulties with the use of semiconductor nanotechnology for this purpose.     

Thiocyanate-capped nanocrystal colloids: vibrational reporter of surface chemistry and solution-based route to enhanced coupling in nanocrystal solids

Ammonium thiocyanate (NH(4)SCN) is introduced to exchange the long, insulating ligands used in colloidal nanocrystal (NC) synthesis. The short, air-stable, environmentally benign thiocyanate ligand electrostatically stabilizes a variety of semiconductor and metallic NCs in polar solvents, allowing solution-based deposition of NCs into thin-film NC solids. NH(4)SCN is also effective in replacing ligands on NCs after their assembly into the solid state. The spectroscopic properties of this ligand provide unprecedented insight into the chemical and electronic nature of the surface of the NCs. Spectra indicate that the thiocyanate binds to metal sites on the NC surface and is sensitive to atom type and NC surface charge. The short, thiocyanate ligand gives rise to significantly enhanced electronic coupling between NCs as evidenced by large bathochromic shifts in the absorption spectra of CdSe and CdTe NC thin films and by conductivities as high as (2 ± 0.7) × 10(3) Ω(-1) cm(-1) for Au NC thin films deposited from solution. NH(4)SCN treatment of PbTe NC films increases the conductivity by 10(13), allowing the first Hall measurements of nonsintered NC solids, with Hall effect mobilities of 2.8 ± 0.7 cm(2)/(V·s). Thiocyanate-capped CdSe NC thin films form photodetectors exhibiting sensitive photoconductivity of 10(-5) Ω(-1) cm(-1) under 30 mW/cm(2) of 488 nm illumination with I(photo)/I(dark) > 10(3) and form n-channel thin-film transistors with electron mobilities of 1.5 ± 0.7 cm(2)/(V·s), a current modulation of >10(6), and a subthreshold swing of 0.73 V/decade.     

Temperature- and field-dependent energy transfer in CdSe nanocrystal aggregates studied by magneto-photoluminescence spectroscopy

The influence of temperature and applied magnetic fields on photoluminescence (PL) emission and electronic energy transfer (ET) of both isolated and aggregated CdSe nanocrystals was investigated. Following 400-nm excitation, temperature-dependent, intensity-integrated and energy-resolved PL measurements were used to quantify the emission wavelength and amplitude of isolated CdSe nanocrystals. The results indicated an approximately three-fold increase in PL intensity upon decreasing the temperature from 300 K to 6 K; this was attributed to a reduction of charge carrier access to nanocrystal surface trap states and suppression of thermal loss channels. Temperature-dependent PL measurements of aggregated CdSe nanocrystals, which included both energy-donating and -accepting particles, were analyzed using a modified version of F?rster theory. Temperature-dependent ET efficiency increased from 0.55 to 0.75 upon decreasing the sample temperature from 225 K to 6 K, and the ET data contained the same trend observed for the PL of isolated nanoclusters. The application of magnetic fields to increase nanocrystal ET efficiency was studied using magneto-photoluminescence measurements recorded at a sample temperature of 1.6 K. We demonstrated that the exciton fine structure population of the donor was varied using applied magnetic fields, which in turn dictated the PL yield and the resultant ET efficiency of the CdSe nanocrystal aggregate system. The experimental data indicated an ET efficiency enhancement of approximately 7%, which was limited by the random orientation of the spherical nanocrystals in the thin film.     

Enhanced multiple exciton dissociation from CdSe quantum rods: the effect of nanocrystal shape

A unique ability of semiconductor nanocrystals (NCs) is the generation and accommodation of multiple excitons through either optical or electric current pumping. The development and improvement of NC-based optoelectronic devices that utilize multiple excitons requires the understanding of multiple exciton dynamics and their efficient conversion to emitted photons or external charges prior to exciton-exciton annihilation. Here, we demonstrate that significantly enhanced multiexciton dissociation efficiency can be achieved in CdSe quantum rods (QRs) compared to CdSe quantum dots (QDs). Using transient absorption spectroscopy, we reveal the formation of bound one-dimensional exciton states in CdSe QRs and that multiple exciton Auger recombination occurs primarily via exciton-exciton collision. Furthermore, quantum confinement in the QR radial direction facilitates ultrafast exciton dissociation by interfacial electron transfer to adsorbed acceptors. Under high excitation intensity, more than 21 electrons can be transferred from one CdSe QR to adsorbed methylviologen molecules, greatly exceeding the multiexciton dissociation efficiency of CdSe QDs.     

Study on interaction between poly(amidoamine) dendrimer and CdSe nanocrystal in chloroform

The binding of different categories of molecules to quantum dot has been studied for many years through different spectroscopic techniques to elucidate details of binding mechanism. In this work we present the results of the study of the interactions between CdSe and poly(amidoamine) dendrimer monitored by photoluminescence spectroscopy of CdSe in chloroform. Dendrimers with different terminal groups and different generations were used to bind with CdSe nanocrystal of different size. Significant differences in the values of binding constant Kb(n) and K(SV) were found in these experiments. The binding constant for poly(amidoamine) dendrimer of generation 4.0 is higher as compared to generation 3.5. The interaction of CdSe with poly(amidoamine) dendrimer shows an increase of binding constants with increasing dendrimer generation from 2.0 to 4.0, as well as with decreasing CdSe diameter. From HRTEM and FTIR analysis, we suggest that dendrimer/CdSe interactions are primarily hydrogen-bonding.     

Time- and polarization-resolved optical spectroscopy of colloidal CdSe nanocrystal quantum dots in high magnetic fields

In an effort to elucidate the spin (rather than charge) degrees of freedom in colloidal semiconductor nanocrystal quantum dots, we report on a series of static and time-resolved photoluminescence measurements of colloidal CdSe quantum dots in ultrahigh magnetic fields up to 45 T. At low temperatures (1.5-40 K), the steady-state photoluminescence (PL) develops a high degree of circular polarization with applied magnetic field, indicating the presence of spin-polarized excitons. Time-resolved PL studies reveal a marked decrease in radiative exciton lifetime with increasing magnetic field and temperature. Except for an initial burst of unpolarized PL immediately following photoexcitation, high-field time-resolved PL measurements reveal a constant degree of circular polarization throughout the entire exciton lifetime, even in the presence of pronounced exciton transfer via F?rster energy transfer processes.     

An alternative of CdSe nanocrystal emitters: pure and tunable impurity emissions in ZnSe nanocrystals

The concept, decoupling doping from nucleation and/or growth, allows us to dope nearly all nanocrystals in a given sample which is indicated by complete quenching of the host emission and bright emission from the dopants at characteristic wavelengths tunable in most parts of the visible window using a ZnSe host. In an extreme case, ZnSe coated MnSe nanocrystals (MnSe:ZnSe) emit similarly as commonly known doped nanocrystals. In comparison with CdSe nanocrystals, these alternative emitters not only are intrinsically less toxic but also show some unexpected and expected advantages: stable against thermal and environmental changes, zero reabsorption, and no Forster energy transfer. In addition to their applications to replace CdSe based nanocrystal emitters, the unique structure and properties of the doped nanocrystals are of interest for studying fundamental issues in the field.     

Adsorption of CdSe nanoparticles to thiolated TiO2 surfaces: influence of intralayer disulfide formation on CdSe surface coverage

Mixed monolayers of hexadecanoic acid (HDA) and 16-mercaptohexadecanoic acid (MHDA) were adsorbed to nanocrystalline TiO2 films, and CdSe nanoparticles were attached to the mixed monolayer functionalized surfaces. IR absorption spectroscopy was used to characterize the equilibrium binding of HDA and MHDA to TiO2. Surface adduct formation constants (Kad) of (4+/-2)x10(3) M(-1) and (6+/-4)x10(3) M(-1) were measured for HDA and MHDA, respectively. CdSe nanoparticles were adsorbed to the terminal thiol groups of MHDA. The surface coverage of CdSe was greater on mixed monolayers, consisting of approximately 12% MHDA and 88% HDA, than on pure MHDA monolayers. A mechanism is proposed wherein intralayer disulfide formation between MHDA thiol groups causes decreased reactivity toward CdSe nanoparticles. Disulfide formation is less significant at low fractional surface coverages of MHDA. The mechanism is supported by an increase of CdSe adsorption upon chemical reduction of surface disulfides to thiols. Our findings highlight the effect of intermolecular interactions on the affinity of nanoparticles for monolayer-functionalized surfaces.     

Effect of the thiol-thiolate equilibrium on the photophysical properties of aqueous CdSe/ZnS nanocrystal quantum dots

We study the effect of thiols on the emission efficiency of aqueous CdSe/ZnS core/shell nanocrystal quantum dots (NQDs). We observe that the impact of thiol addition on emission quantum yields (QYs) is time-, concentration-, and pH-dependent. Further, we use a combination of time-resolved spectroscopic methods to determine the mechanism by which thiol addition can cause either increases or decreases in QYs. Specifically, through transient absorption measurements, we show that thiol addition can improve passivation of electron traps, increasing QYs at low thiol concentrations. Further, using nanosecond photoluminescence (PL), we observe that at higher thiol concentrations, hole traps are introduced that reduce PL QYs. Last, through a combination of pH-dependence and control studies (e.g., addition of 2-methyl thioethanol to an aqueous NQD solution and addition of dodecanethiol to a hexane NQD solution), we demonstrate that it is the ability of thiols in aqueous solution to generate thiolate that is the source of both favorable and adverse QY changes. Our results contribute to the understanding of the role of surface ligands, which is critical to the design of stable, high-quantum-yield, nonblinking NQDs.     

Ligand exchange on colloidal CdSe nanocrystals using thermally labile tert-butylthiol for improved photocurrent in nanocrystal films

As-prepared CdSe nanocrystals were ligand exchanged using tert-butylthiol, which yielded stable CdSe nanocrystal inks in the strong donor solvent tetramethylurea. The efficacy of ligand exchange was probed by thermogravimetric analysis (TGA) and FT-IR spectroscopy. By studying sequential exchanges of tetradecylphosphonic acid and then tert-butylthiol, TGA and energy dispersive X-ray spectroscopic evidence clearly demonstrated that the ligand exchange is essentially quantitative. The resulting tert-butylthiol-exchanged CdSe nanocrystals undergo facile thermal ligand expulsion (≤200 °C), which was studied by TGA-mass spectrometry. Mild thermal treatment of tert-butylthiol-exchanged CdSe nanocrystal films was found to induce loss of quantum confinement (as evidenced by UV-vis spectroscopy) and provided for increased electrochemical photocurrent, electron mobility, and film stability. Pyridine-exchanged CdSe nanocrystals were employed as a control system throughout to demonstrate the beneficial attributes of tert-butylthiol exchange; namely, lower organic content, better colloidal stability, improved interparticle coupling, and vastly increased electrochemical photocurrent response upon illumination.     

Maghemite nanocrystal impregnation by hydrophobic surface modification of mesoporous silica

Here, we report the design of a hybrid inorganic/organic mesoporous material through simultaneous pore engineering and hydrophobic surface modification of the intramesochannels to improve the uptake of superparamagnetic maghemite nanocrystals via impregnation techniques. The mesoporous material of the SBA-15 type was functionalized in situ with thiol organo-siloxane groups. Restricting the addition of the thiol organo-siloxane to 2 mol % yielded an inorganic/organic hybrid material characterized by large pores and a well-ordered hexagonal p6mm mesophase. The hydrophobic surface modification promoted the incorporation of 7.5 nm maghemite (gamma-Fe2O3) nanocrystals, prepared through temperature-controlled decomposition of iron pentacarbonyl in organic solvents. The hydrophobic, oleic acid capped superparamagnetic maghemite nanocrystals were incorporated into the porous network via wet impregnation from organic suspensions. Combining diffraction, microscopy, and adsorption data confirmed the uptake of the nanocrystals within the intramesochannels of the silica host. Magnetization dependencies on magnetic field at different temperatures show a constriction in the loop around the origin, which indicates immobilization of maghemite nanocrystals inside the thiol-functionalized silica host.     

Application of a microfluidic reaction system for CdSe nanocrystal preparation: their growth kinetics and photoluminescence analysis

We used a microreactor for CdSe nanocrystal preparation and explored the effects of experimental conditions on the properties of the products. The particle growth kinetics and photoluminescence properties of the nanocrystals showed identical trends to previous reports, indicating the efficiency of the current method for analysis of rapid nanocrystal synthesis as well as industrial production of CdSe nanocrystals.     

Chemical surface deposition and growth rate of thin CdSe films

Chemical surface deposition of thin CdSe films was studied. The conditions for preparing thin films were examined, the degrees of Cd conversion in the starting compounds were determined, and the film thicknesses were measured.     

Fine tuning photoluminescence properties of CdSe nanoparticles by surface states modulation

Fine control of the photoluminescence properties of CdSe nanoparticles (NPs) dispersed in CHCl3 is achieved by simple adjustment of the NPs concentration, and the wavelength of photoluminescence emission of CdSe NPs can be tuned within the nanometer accuracy. The mechanism of the process is proposed to be relevant to the modulation of the surface states of NPs by the concentration. This solution-based approach offers an attractive and complementary process to the conventional band gap engineering of semiconductor NPs with fine tunable optical properties.     

Controlling nanocrystal superlattice symmetry and shape-anisotropic interactions through variable ligand surface coverage

The assembly of colloidal nanocrystals (NCs) into superstructures with long-range translational and orientational order is sensitive to the molecular interactions between ligands bound to the NC surface. We illustrate how ligand coverage on colloidal PbS NCs can be exploited as a tunable parameter to direct the self-assembly of superlattices with predefined symmetry. We show that PbS NCs with dense ligand coverage assemble into face-centered cubic (fcc) superlattices whereas NCs with sparse ligand coverage assemble into body-centered cubic (bcc) superlattices which also exhibit orientational ordering of NCs in their lattice sites. Surface chemistry characterization combined with density functional theory calculations suggest that the loss of ligands occurs preferentially on {100} than on reconstructed {111} NC facets. The resulting anisotropic ligand distribution amplifies the role of NC shape in the assembly and leads to the formation of superlattices with translational and orientational order.     

Cellulose nanocrystal surface functionalization for the controlled sorption of water and organic vapours

The surface grafting of cellulose nanocrystals (CNC) is a valuable tool to increase opportunities for their application. This work had several goals designed to improve CNC: reduction of hornification, increased re-dispersibility after CNC drying, and tuning of the surface graft to enhance the adsorption of particular molecules. To achieve this, the CNC surfaces were modified chemically with aromatic surface grafts using widely employed methods: the creation of urethane linkages, silylation and esterification. Even a low degree of grafting sufficed to increase water contact angles to as much as 96°. The analysis of water sorption isotherms showed that at high water activities, capillary condensation could be suppressed and hysteresis was decreased. This indicates that hornification was significantly suppressed. However, although the contact angles increased, the water sorption isotherms were changed only slightly because of reduced hysteresis. The grafts were not able to shield the surface from water vapour sorption. A comparison of the sorption isotherms of anisole and cyclohexane, sorbates with a similar surface area, showed that the sorption of anisole was three times higher than that of cyclohexane. The specific sorption of aromatic molecules was achieved and the most efficient methodology was the esterification of CNC with carboxylic acids containing a flexible linker between the aromatic moiety and ester bond.