超稠油供氢水热裂解改质降黏研究

通过超稠油水热裂解反应前后黏度、沥青质、硫质量分数等性质的变化，研究了超稠油进行水热裂解的主要影响因素及规律。结果表明，超稠油中含有一定量的硫是地层注蒸汽温度下进行水热裂解反应的前提。温度和时间对反应有很大影响。供氢剂中四氢萘对超稠油水热裂解影响最大。四氢萘供氢剂与硫酸镍催化剂复配使用对超稠油水热裂解有协同效应。水热裂解物理模拟实验表明,胜利单家寺油田超稠油通过供氢催化水热裂解降黏率可达70%以上。胶质、沥青质、硫质量分数降低，H/C原子比提高，超稠油得到一定程度的改善。     

4E analysis and tri-objective optimization of a triple-pressure combined cycle power plant with combustion chamber steam injection to control NOx emission

This article presents a novel triple-pressure combined cycle power plant (CCPP) with a heat recovery steam generator (HRSG) configured with heat exchangers of multiple pressure levels, same as the real case. In addition, combustion chamber steam injection is added to the top cycle in order to reduce hazardous emissions. The research investigates energy, exergy, economic, and environmental aspects of the system to initiate sustainable development in said areas. A thorough parametric study is carried out to evaluate the effects of steam injection and other decision variable on emissions and system performance. Then, the total cost rate and the CO₂ index are minimized while maximizing the second law efficiency via a tri-objective optimization using the genetic algorithm. The outcome of the economic analysis is that the HRSG has the maximum total cost rate among all the components, namely 0.1673 $/s. The environmental impact  assessments indicate that the CO₂ and NO emission has considerable molar fractions of 0.035 and 6.88?×?10^?4, respectively. As a result of the tri-objective optimization, a 3D Pareto Frontier is presented, which pointed out the maximum attainable exergy efficiency is 50.32%, as well as the minimum total cost rates of 8.04 $/s and CO₂ index of 0.34 kg/kWh. Finally, the scatter distribution of major decision variables revealed the optimum range of decision variables in which the optimum points of the Pareto Frontier are obtained. Accordingly, the scatter distribution showed that 46 kg s^?1 is the optimum value for steam injection flow rate in terms of efficiency, cost and emission optimization.

     

废聚丙烯塑料等离子体热解研究——水蒸气的加入对改善气体品质的影响

以聚丙烯为试验物料，利用N2热等离子体在等离子体反应器内进行了一系列热解试验，重点考察了气体产物成分及含量。在反应过程中加入过热水蒸气以改善气体品质，在本实验条件下，气体产物中CO与H2之和可以达到40%，C2H2可达到5%。     

Reduction Characteristics of Carbon Dioxide Using a Plasmatron

To decompose carbon dioxide, which is a representative greenhouse gas, a 3-phase gliding arc plasmatron device was designed and manufactured to examine the decomposition of CO₂, either alone or in the presence of methane with and without water vapour. The changes in the amount of carbon dioxide feed rate, the methane to carbon dioxide ratio, the steam to carbon dioxide ratio, and the methane to steam ratio were used as the parameters. The carbon dioxide conversion rate, energy decomposition efficiency (EDE), carbon monoxide and hydrogen selectivity, and produced gas concentration were also investigated. The maximum values of the carbon dioxide conversion rate, which is a key indicator of carbon dioxide decomposition, in different cases were compared. The maximum carbon dioxide conversion rate was 12.3 % when pure carbon dioxide was supplied; 34.5 % when methane was injected as a reforming additive; 7.8 % when steam was injected as a reforming additive; and 43 % when methane and steam were injected together. Therefore, this could be explained that the methane-and-steam injection showed the highest carbon dioxide decomposition, showing low EDE as 0.01 L/min W. Furthermore, the plasma produced carbon-black was compared with commercial carbon-black chemicals through Raman spectroscopy, surface area measurement and scanning electron microscopy. It was found that the carbon-black that was produced in this study has the high conductivity and large specific surface area. Our product makes it suitable for special electric materials and secondary battery materials applications.     

Decontamination Efficiency of Thermal,Photothermal, Microwave,and Steam Treatments for Biocontaminated Household Textiles

With the outbreak of the COVID-19 pandemic, textile laundering hygiene has proved to be a fundamental measure in preventing the spread of infections. The first part of our study evaluated the decontamination efficiency of various treatments (thermal, photothermal, and microwave) for bio contaminated textiles. The effects on textile decontamination of adding saturated steam into the drum of a household textile laundering machine were investigated and evaluated in the second part of our study. The results show that the thermal treatment, conducted in a convection heating chamber, provided a slight reduction in efficiency and did not ensure the complete inactivation of Staphylococcus aureus on cotton swatches. The photothermal treatment showed higher reduction efficiency on contaminated textile samples, while the microwave treatment (at 460 W for a period of 60 s) of bio contaminated cotton swatches containing higher moisture content provided satisfactory bacterial reduction efficiency (more than 7 log steps). Additionally, the treatment of textiles in the household washing machine with the injection of saturated steam into the washing drum and a mild agitation rhythm provided at least a 7 log step reduction in S. aureus. The photothermal treatment of bio contaminated cotton textiles showed promising reduction efficiency, while the microwave treatment and the treatment with saturated steam proved to be the most effective.     

Thermal and rheological study of polysaccharides for enhanced oil recovery

Enhanced oil recovery process is based on the injection of chemical products (e.g. polymers, surfactants, gases) or thermal energy (originating from the injection of e.g. steam, hot water, in situ combustion) to recover crude oil. One of these processes use polymer solution to mobilize the oil in the reservoir. In this work the thermal decomposition kinetic of xanthan gum, guar gum and a blend (50/50 mass/mass%) was studied according to Ozawa–Flynn–Wall method. According to the kinetic analysis, the studied systems were copmpatible. The rheological behavior of the samples was studied in distilled water and seawater at different temperatures. Only the blend was studied in distilled water presented synergism (enhancement in material properties like stability and viscosity) which was confirmed through rheology.     

水蒸汽对PtSn／Al2O3催化剂结构及反应性能的影响

比较研究了Ａｌ２Ｏ３负载的铂及ＰｔＳｎ催化剂在氮气及水蒸汽稀释条件下的丙烷脱氢性能,并利用ＸＰＳ及氢脉冲吸附对催化剂进行了表征。结果表明,水蒸汽可促使Ｐｔ／Ａｌ２Ｏ３催化剂的铂晶粒烧结。与在氮气氛中相比,在水蒸汽存在下反应显著提高了Ｐｔ／Ａｌ２Ｏ３的丙烷转化率,却降低了丙烯的选择性。另一方面,水蒸汽可调变ＰｔＳｎ／Ａｌ２Ｏ３催化剂的结构,破坏了ＰｔＳｎ／Ａｌ２Ｏ３中与锡相互作用的铂簇团结构。从而导     

碱金属钾对Ni基催化剂纤维素水蒸气气化活性的影响

采用两段式催化气化方式研究了生物质热解气化过程中碱金属的挥发对Ni基催化剂活性的影响。实验结果表明,负载K盐的纤维素水蒸气催化气化过程中,K挥发后会在催化剂表面沉积,而少量K的存在和表面沉积不但能够提高镍基催化剂的抗积炭能力,而且有助于提高其催化活性,产生更多的氢气。然而纤维素中K的浓度过大,将会抑制Ni基催化剂的效果;K在催化剂上的沉积随催化剂循环次数的增加而增加,K的含量愈高,对催化剂的抑制效果愈明显,从而缩短了催化剂的使用寿命。     

蒸气开采过程中金属盐对稠油粘度及平均分子量的影响

探讨了在注蒸气条件下，稠油的粘度和平均分子量随蒸气温度、反应时间的变化规律，研究了金属盐、油层矿物对稠油水热裂解反应的影响。实验结果表明，在注蒸气的条件下，辽河稠油可以发生水热裂解反应。金属盐的存在，可以加速稠油的水热裂解反应，从而导致粘度和平均分子量的进一步降低，使稠油的粘度由原始的124.5 Pa·s下降到32.4 Pa·s，下降了74.0%，平均分子量由反应前的654下降到398。高温下油层矿物对水热裂解反应有促进作用，在反应体系中，在有水时加入质量分数为10%的油层矿物时，稠油的粘度由原始的124.5 Pa·s下降到82.5 Pa·s，下降了33.7%。在蒸气条件下，在金属盐和油层矿物共存时，稠油粘度由124.5 Pa·s下降到26.8 Pa·s，下降了78.5%。这为实现井下催化降粘开采稠油提供了理论依据。     

On conditions ensuring the highest difference in the association degrees of the equilibrium H and D steams: Clustering and isotope enrichment

A search for conditions leading to the highest possible difference between equilibrium association (clustering) degree in the H and D steam has been carried out and related optimal steam pressures evaluated. The difference decreases with increasing temperature but still is a few per cent at moderate temperatures.     

Understanding effect of wall structure on the hydrothermal stability of mesostructured silica SBA-15

Mesostructured silica SBA-15 materials with different structural parameters, such as pore size, pore volume, and wall thickness, etc., were prepared by varying the postsynthesis hydrothermal treatment temperature and adding inorganic salts. The hydrothermal stabilities of these materials in steam (100% water vapor) were systematically investigated using a variety of techniques including powder X-ray diffraction, transmission electron microscopy, nitrogen sorption, and (29)Si solid-state NMR. The effect of the pore size, microporosity or mesoporosity, and wall thickness on the stability was discussed. The results show that all of the SBA-15 materials have a good hydrothermal stability under steam of 600 degrees C for at least 24 h. N(2) sorption measurements show that the Brumauer-Emmett-Teller surface area of SBA-15 materials is decreased by about 62% after treatment under steam at 600 degrees C for 24 h. The materials with thicker walls and more micropores show relatively better hydrothermal stability in steam of 600 degrees C. Interestingly, we found that the microporosity of the mesostructured silica SBA-15 is a very important factor for the hydrothermal stability. To the materials with more micropores, the recombination of Si-O-Si bonds during the high-temperature steam treatment may not cause direct destruction to the wall structure. As a result, SBA-15 materials with more micropores show better stability in pure steam of 600 degrees C. Nevertheless, these materials are easily destroyed in steam of 800 degrees C for 6 h. Two methods to effectively improve the hydrothermal stability are introduced here: one is a high-temperature treatment, and another is a carbon-propping thermal treatment. Thermal treatment at 900 degrees C can enhance the polymerization degree of Si-O-Si bonds and effectively improve the hydrothermal stability of these SBA-15 materials in 800 degrees C steam for 12 h. But, this approach will cause very serious shrinkage of the mesopores, resulting in smaller pore diameter and low surface area. A carbon-propping thermal treating method was employed to enhance the polymerization of Si-O-Si bonds and minimize the serious shrinkage of mesopores at the same time. It was demonstrated to be an effective method that can greatly improve the hydrothermal stability of SBA-15 materials in 800 degrees C steam for 12 h. Furthermore, the SBA-15 materials obtained by using the carbon-propping method possess larger pores and higher surface area after the steam treatment at 800 degrees C compared to the materials from the direct thermal treatment method after the steam treatment.     

Influence of steam explosion on the thermal stability of cellulose fibres

The aim of the present study was to compare the effect of different steam explosion treatments on the thermal degradation of a bleached cellulose. The intensity of a steam explosion treatment, which allows breakdown of the structural lignocellulosic material was determined by a correlation between time and temperature of the process.Results of this study showed that thermal degradation of cellulose fibres was limited when the severity factor applied was below 4.0. For higher intensities, determination of the degradation products in the water-soluble extract showed an important increase of the 5-hydroxymethyl-furfural concentration with the temperature. When the severity factor reached 5.2., TGA analysis showed that the increase of degradation products was coupled to an increase of the char level meaning a strong degradation of the cellulose. dTGA behaviour also showed that thermal stability of the steam explosion samples decreased with the intensity of the treatment. To conclude, a theoretical diagram predicting the degradation of the cellulose during the steam explosion treatment was established.     

水蒸气对煤热转化过程中钠析出特性影响研究

在不同水蒸气体积分数及温度条件下制备了相同焦产率的NaCl浸渍煤的煤焦样品,并利用电感耦合等离子体质谱仪分析了不同煤焦中钠的赋存形态及含量,研究了水蒸气及温度对煤热转化过程中钠迁徙转化的影响。结果表明,水蒸气体积分数的增加,一方面,增强了煤热转化过程中水溶态钠的释放;另一方面,也促进了水溶态钠向醋酸铵溶态、盐酸溶态以及不溶态钠的转化,使得钠的释放受到一定程度抑制。煤焦结构演化对碱金属钠释放具有重要影响。水蒸气的气化反应引起煤焦缩聚程度增加,小芳香环缩聚形成大芳香环结构时会对钠起到一定的包裹作用,使得钠的释放受到抑制;同时,气化反应产生的煤焦比表面积越大,越有利于钠直接释放。提高反应温度一方面会促进水溶态钠的释放;同时也会促进水溶态钠向其他溶态形式钠的转化,使得钠析出率随反应温度上升而增加的趋势逐渐变缓。     

Influence of pre-curing time on the hydration of binder and the properties of concrete under steam curing condition

There is a pre-curing period before the freshly made concrete elements were exposed to steam curing in the steam curing process. In this paper, the influence of pre-curing time on the hydration of binder and the properties of concrete under steam curing condition was investigated. Three binders were used: the pure cement, the binder containing high content of GGBS, and the binder containing high content of fly ash. Three pre-curing times (1, 3, and 6 h) and one steam curing period at 60 °C (over 8 h) were adopted. Results show that pre-curing time has limited influence on the hydration degree of binder, and compressive strength and pore structure of paste. The influence of pre-curing time has limited influence on the compressive strength and chloride permeability of the pure cement concrete and the concrete containing high content of GGBS at whether early or late ages, indicating that the proper pre-curing time can be as short as 1 h for these two concretes. Increasing pre-curing time enhances the late-age compressive strength of the concrete containing high content of fly ash significantly, but it has limited influence on the late-age permeability.     

水蒸汽蒸馏条件下鱼腥草中癸酰乙醛的高效提取及质谱定性

根据质谱学规律,剖析了在电子轰击下中药材鱼腥草中最关键的抗菌成分鱼腥草素(癸酰乙醛)的离子形成机理:癸酰乙醛的分子中存在两个-C=O,处于端位上的-C=O活性远大于-CH3,易失去H2O(M+-18)、CO(M+-28)等基团,产生较强的m/z180、170等离子碎片,此外,还易失去H2O+H2O(M+-36)、H2O+CO(M+-46)、CO+CO(M+-56)等基团,产生m/z162、152、142等离子碎片,这同实验中得到的癸酰乙醛质谱图完全吻合,纠正了文献中对癸酰乙醛的错误定性。在此基础上采用常规、Ar气保护和减压三种水蒸汽蒸馏方式提取鱼腥草挥发油,发现在惰性气氛或较低温度下有利于癸酰乙醛的提取,与常规水蒸汽蒸馏条件相比,Ar气保护下癸酰乙醛的含量从0.03%提高至0.53%,而减压条件下癸酰乙醛的溶出效率进一步提高至3.37%。研究表明常规水蒸汽蒸馏条件下癸酰乙醛易氧化分解是得到较少癸酰乙醛的根本原因。     

稀土添加剂对烃类水蒸汽重整镍催化剂性能的影响——水蒸汽吸附的TPD研究

用程序升温脱附技术,研究了添加稀土的烃类水蒸汽重整催化剂(Ni/α-Al_2O_3)对水蒸汽的吸附性能,同未加稀土的镍催化剂作了对比。结果表明,加有稀土的镍催化剂对水蒸汽的吸附能力主要是稀土的贡献。还原态催化剂对水蒸汽的吸附量比相应的氧化态多1.4倍。发现催化剂对水蒸汽的吸附能力不仅取决于浸渍方式,而且同稀土含量有关。当稀土含量较多时,催化剂表面上呈现出三个能量不同的吸附位。稀土含量少于1.3%时。对提高催化剂吸附水蒸汽的能力已作用不大。含稀土的镍催化剂吸附水蒸汽的能力大,正是其抗结炭性能耐硫性能好的原因。     

New data on gas-phase radical reactions in the steam reforming of methane in the presence of catalysts: I. Nickel catalysts

Methane pyrolysis and steam reforming were studied over a series of nickel catalysts (Ni-Al₂O₃, Ni/MgO, and Ni/LiAlO₂) under the same conditions (650-750°C, P_CH4 = 0.001-0.03 MPa). Unlike heterogeneous reaction of pyrolysis, some of the steps of steam reforming of methane occur in the gas phase. When gasphase reactions were suppressed, the rate and activation energy of steam reforming are close to the corresponding kinetic characteristics for pyrolysis. Hypothetically, the rate-limiting step of the process is the dissociative adsorption of methane on nickel in this case.     

蒙古国巴嘎诺尔(Baganuur)褐煤水蒸气气化制富氢合成气及其固有矿物质的催化作用

利用固定床气化-色谱联用装置,考察了蒙古国巴嘎诺尔(Baganuur)褐煤的水蒸气气化反应性能,研究对比了巴嘎诺尔褐煤原煤BN-R、盐酸洗煤BN-HCl、氨水洗煤BN-NH₄OH、先酸洗后碱处理煤BN-HCl-NaOH及原煤和盐酸洗煤热解预处理煤样BN-R-Char与BN-HCl-Char在水蒸气气化过程中气态产物H₂、CO和CO₂的生成规律.研究结果表明,上述煤样的水蒸气气化过程中H₂、CO和CO₂的生成速率存在明显差异,与盐酸洗煤样相比,BN-R、BN-HCl-NaOH及BN-R-Char比对应矿物质脱除煤样的水蒸气气化速率高,充分说明巴嘎诺尔褐煤中某些固有矿物质对其水蒸气气化反应具有显著的催化作用,显著提高了其气化反应速率,使起始气化温度和气化反应主体温度均降低100 ℃以上,在提高H₂和CO₂生成量同时,还降低了CO生成量,制得了高H₂/CO(物质的量比)的合成气.用盐酸脱除矿物质所得BN-HCl同BN-HCl-Char的水蒸气气化性能相似.与BN-R相比,BN-HCl与BN-HCl-Char水蒸气气化反应性明显下降,说明对巴嘎诺尔褐煤水蒸气气化起催化作用的矿物质成分在盐酸洗脱的矿物质中.经过分析,发现矿物质对巴嘎诺尔褐煤水蒸气气化反应的催化作用,主要是通过提高水煤气变换反应速率实现的.最后,结合文献报道,提出了巴嘎诺尔褐煤水蒸气气化反应过程中矿物质的原位催化机理.     

Modeling of a MED-TVC desalination system by considering the effects of nanoparticles: energetic and exergetic analysis

In this study, the energetic and exergetic analysis of a multi-effect desalination system with a thermal vapor compression desalination system has been numerically evaluated. For this purpose, the mass, energy, and exergy balance equations for the thermo-compressor, first effect as well as middle effects, and condenser have been developed. The effects of motive steam pressure and number of effects on yield, gained output ratio (GOR), performance ratio (PR) and irreversibility have been examined. Nanoparticles were used to improve the heat transfer properties at different stages. The highest rate of exergy destruction with 61.67% is concerned with thermo-compressor, owing to the large difference between the motive steam pressure and the entrained steam. The lowest exergy losses rate among the various components was 4.89% for the condenser, due to the fact that much of the final distillate steam entrained the thermo-compressor. As the number of effects increased from 1 to 7, the yield, GOR as well as PR, improved by approximately 590% and the irreversibility reduced by 1.88%. As the motive steam pressure increased from 400 to 1290 kPa, the yield decreased by 25.45% while the GOR and PR improved by 12.62 and 14.8%, respectively. From the second law viewpoint, irreversibility intensified by 16.11% which in turn diminished the second efficiency by 3.17%.

     

乙醇浸提南沙参挥发油化学成分分析

采用乙醇浸提水蒸气蒸馏方法提取南沙参中挥发油,用气相色谱/质谱联用技术对提取的挥发油进行了分离鉴定,鉴定出烃类、醛类、醇类、酮类、酯类、酸类、呋喃类、醚类和酰胺类9类61种化合物,其中8种化合物(占66.952%)为已知药用成分,这些数据为进一步评价其质量和开发新药提供了基础数据.