Preparation, characterization and electrochemical performance of γ-MnO2 and LiMn2O4 as cathodes for lithium batteries

The spinel LiMn₂O₄ is a very promising cathode material with economical and environmental advantages. LiMn₂O₄ materials have been synthesized by solid state method using γ-MnO₂ as manganese source, and Li₂CO₃ or LiNO₃ as Li sources. γ-MnO₂ is a commercial battery grade electrolytic manganese dioxide (TOSOH-Hellas GH-S) and LiMn₂O₄ samples were synthesized at a calcinations temperature up to 800 °C. γ-MnO₂ and LiMn₂O₄ samples were characterized by X-ray diffraction, thermal and electrochemical measurements. X-ray powder diffraction of as prepared LiMn₂O₄ showed a well-defined highly pure spinel single phase. The electrochemical performance of LiMn₂O₄ and its starting material γ-MnO₂ was evaluated through cyclic voltammetry, galvanostatic (constant current charge-discharge cycling) The electrochemical properties in terms of cycle performance were also discussed. γ-MnO₂ showed fairly high initial capacity of about 200 mAhg⁻¹ but poor cycle performance. LiMn₂O₄ samples showed fairly low initial capacity but good cycle performance.     

Enhancement of the electrochemical properties of LiMn2O4 by glycolic acid-assisted sol-gel method

LiMn₂O₄ spinel cathode was synthesized by the sol–gel method by using glycolic acid as a chelating agent. The sample exhibited a pure cubic spinel structure without any impurities in the X-ray diffraction (XRD) patterns. The result of the electrochemical performances on the sample compared to those of electrodes based on LiMn₂O₄ spinel synthesized by solid state. LiMn₂O₄ synthesized by glycolic acid-assisted sol–gel method improves the cycling stability of electrode. The capacity retention of sol–gel-synthesized LiMn₂O₄ was about 90• after 100 cycles between 3.0 and 4.4 V at room temperature. The electrochemical performance of the LiMn₂O₄ (sol–gel) and LiMn₂O₄ (solid state) were investigated under 40• between 3.0 and 4.4 V. XRD results of the cathode material after 50 cycles at 40• revealed that LiMn₂O₄ (sol–gel) could effectively suppress the LiMn₂O₄ dissolving of into electrolyte and resulted in a better stability.     

Novel approach to preparation of LiMn2O4 core/LiNixMn2−xO4 shell composite

Combining two methods, coating and doping, to modify spinel LiMn₂O₄, is a novel approach we used to synthesize active material. First we coated the LiMn₂O₄ particles with the nickel oxide particles by means of homogenous precipitation, and then the nickel oxide-coated LiMn₂O₄ was calcined at 750 °C to form a LiNi_xMn_2−xO₄ shell on the surface of spinel LiMn₂O₄ particles. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), cyclic voltammetry (CV) and charge-discharge test were performed to characterize the spinel LiMn₂O₄ before and after modification. The experimental results indicated that a spinel LiMn₂O₄ core is surrounded by a LiNi_xMn_2−xO₄ shell. The resulting composite showed excellent electrochemical cycling performance with an average fading rate of 0.014% per cycle. This improved cycle stability is greatly attributed to the suppression of Jahn-Teller distortion on the surface of spinel LiMn₂O₄ particles during cycling.     

Synthesis of Co-coated lithium manganese oxide and its characterization as cathode for lithium ion battery

Co-coated LiMn₂O₄ was synthesized by electroless plating. The phase identification, surface morphology, and electrochemical properties of the synthesized powders were studied by X-ray diffraction, scanning electron microscopy, electrochemical impedance spectroscopy, and galvanostatic charge–discharge experiments, respectively. The result shows that Co-coated LiMn₂O₄ particle has a coarse surface with a lot of holes. The specific capacity of Co-coated LiMn₂O₄ is 118 mAh g⁻¹, which is a bit less than 123 mAh g⁻¹ for the uncoated LiMn₂O₄. The capacity retention of Co-coated LiMn₂O₄ is 11% higher than the uncoated LiMn₂O₄ when the electrode is cycled at room temperature for 20 times. When cycled at the temperature of 55 °C, the capacity retention of Co-coated LiMn₂O₄ becomes 15% higher than the uncoated one.     

Preparation of TiO2-coated LiMn2O4 by carrier transfer method

The TiO₂-coated LiMn₂O₄ has been prepared by a carrier transfer method and investigated. This novel synthetic method involved the transfer of TiO₂ into the surface of LiMn₂O₄ with Vulcan XC-72 active carbon powders as a dispersant. The X-ray diffraction shows that spinel structure of materials does not change after the coating of TiO₂. The electrochemical performance tests show that the initial discharge capacity of TiO₂-modified LiMn₂O₄ is 111.5 mA h g⁻¹, which is better than that of pristine LiMn₂O₄ (103.8 mA h g⁻¹). The cyclic performance is significantly improved after surface modification. The TiO₂-modified LiMn₂O₄ by a carrier transfer method exhibits better discharge capability and lower resistance.     

Malonic acid assisted sol-gel synthesis and characterization of chromium doped LiMn2O4 spinel

Pristine LiMn₂O₄ and LiCr_xMn_2-xO₄ (x=0.01−0.20) have been synthesized by sol-gel method using malonic acid as chelating agent. This technique involves less impurities, shorter heat treatment time, sub-micron sized particles, good surface morphology, better homogeneity, good agglomeration and better crystallinity. The synthesized spinel materials have been characterized by XRD, SEM, TEM, EDAX and electrochemical studies like charge-discharge studies, cyclic voltammogram, cycleability studies have also been carried out. All the results exhibit that chromium substitution improves the structural stability of LiMn₂O₄ spinel upon repeated cycling.     

LiPF6-EC-MPC electrolyte for LiMn2O4 cathode in lithium-ion battery

Methyl propyl carbonate (MPC) is a promising single solvent for lithium-ion battery without addition of ethylene carbonate (EC), but it is unstable upon cycling because of exposure to the spinel LiMn₂O₄ cathode. Thus, we attempted to add EC to MPC in order to form LiPF₆-EC-MPC electrolyte; the effects of solvent ratio and salt concentration on the cycling performance of LiMn₂O₄ cathode were also investigated. The experiments were characterized by conductivity measurements, charge-discharge at a constant current density and voltage–capacity curves at low temperature. To further enhance our understanding of the performance improvement of LiMn₂O₄/Li cells, the electrochemical characterization techniques (such as, LSV, EIS) were performed on these cells. The results show that the ionic conductivity of the electrolyte and the cycling performance of the spinel LiMn₂O₄ cathode have been dramatically enhanced. From the point of view of operation at low temperature (− 20 °C), 1 M LiPF₆ EC/MPC (1/3) electrolyte is highly recommended for spinel LiMn₂O₄ cathode in lithium-ion battery.     

Origin of self-discharge mechanism in LiMn2O4-based Li-ion cells: A chemical and electrochemical approach

LiMn₂O₄-based Li-ion cells suffer from a limited cycle-life and a poor storage performance at 55 °C, both in their charged and discharged states. To get some insight on the origin of the poor 55 °C storage performance, the voltage distribution through plastic Li-ion cells during electrochemical testing was monitored by means of 3-electrode type measurements. From these measurements, coupled with chemical analysis, X-ray diffraction and microscopy studies, one unambiguously concludes that the poor performance of LiMn₂O₄/C-cells at 55 °C in their discharged state is due to enhanced Mn dissolution that increases with increasing both the temperature and the electrolyte HF content. These results were confirmed by a chemical approach which consists in placing a fresh LiMn₂O₄ electrode into a 55 °C electrolyte solution. A mechanism, based on an ion-exchange reaction leading to the Mn dissolution is proposed to account for the poor storage performance of LiMn₂O₄/C Li-ion cells in their discharged state. In order to minimize the Mn dissolution, two surface treatments were performed. The first one consists in applying an inorganic borate glass composition to the LiMn₂O₄ surface, the second one in using an acetylacetone complexing agent. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

Improvement of storage performance of LiMn2O4/graphite battery with AlF3-coated LiMn2O4

LiMn₂O₄/graphite batteries using AlF₃-coated LiMn₂O₄ have been fabricated and their electrochemical performance including discharge capacity and cyclic and storage performances have been tested and compared with pristine LiMn₂O₄/graphite batteries. The LiMn₂O₄/graphite battery with AlF₃-coated LiMn₂O₄ shows better capacity (108.5 mAhg^?1), cyclic performance (capacity retention of 92.7 % after 70 cycles), and capacity recovery ratio (98.6 %) than the pristine LiMn₂O₄ battery. X-ray diffraction patterns shows that the spinel structure of AlF₃-coated LiMn₂O₄ can be controlled better than that of pristine LiMn₂O₄ after storage. The improvement in electrochemical performance of the AlF₃-coated LiMn₂O₄/graphite battery is due to the fact that AlF₃ acts as a stabilizer and can protect the oxide structure from damaging during storage, leading to a smaller resistance and polarization after storage.     

Vibrational studies of spinel LixMn2O4 (0.3≤x≤1.0) cathodes

We report on the vibrational properties of spinel LiMn₂O₄ and its electrochemically delithiated forms Li_xMn₂O₄. Raman scattering and infrared absorption spectra have been studied as a function of the delithiation content in the wavenumber range 50–700 cm⁻¹. Results show that lithium ions can be extracted at room temperature to obtain Li_x[Mn₂]O₄ (0.3≤x≤1.0) without disrupting the [Mn₂]O₄ array. The normal modes of the spinel LiMn₂O₄ have been discussed in the O _h ⁷ symmetry and vibrations due to lithium ions with their oxygen neighbors have been identified at ca. 400 cm⁻¹. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy, Sept. 15–22, 1996     

Synthesis and electrochemical performance of Li1+xV3O8 as cathode material prepared by citric acid and tartaric acid assisted sol–gel processes

Lithium-ion battery cathode material Li_1+xV₃O₈ is synthesized by a citric acid/tartaric acid assisted sol–gel method and sintered at 350 °C, 450 °C and 550 °C for 3 h for the formation of Li_1+xV₃O₈ phase. The synthesized samples were fully characterized by FTIR, TG/DTA, XRD, SEM, EIS and charge–discharge tests. Li_1+xV₃O₈ material synthesized by tartaric acid assisted route and sintered at 450 °C for 3 h shows best electro-chemical performance. It shows a high initial capacity of 249 mAh g^?1 and still reserves a discharge capacity of 260 mAh g^?1 after 50 cycles. Moreover, in the case of tartaric assisted products, no capacity decadence is observed in 50 cycles. XRD together with TG/DTA measurements reveal that compared with citric acid assisted products, the adoption of tartaric acid as chelating agent effectively lowers the crystallization temperature of amorphous Li_1+xV₃O₈. Therefore, precursors obtained by tartaric acid route calcinated at 450 °C for 3 h exhibit lower crystallinity and smaller grain size, which contributes to the better electrochemical performance of the cathode electrodes. From EIS measurements, the bulk resistance is reduced, which favors the intercalation and de-intercalation of lithium ions while cycling.     

Structure and electrochemical performance of LiV x Mn2 − x O4 (0 ≤ x ≤ 0.20) cathode materials for rechargeable lithium ion batteries

LiMn₂O₄ and vanadium-substituted LiV _x Mn_2???x O₄ (x?=?0.05, 0.10 0.15 and 0.20) cathode materials were synthesized by sol–gel method using aqueous solutions of metal nitrates and tartaric acid as chelating agent at 600 °C for 10 h. The structure and electrochemical properties of the synthesized materials were characterized by using X-ray diffraction, SEM, TEM and charge–discharge studies. X-ray powder diffraction analysis was changed in lattice parameters with increasing vanadium content suggesting the occupation of the substituent within LiMn₂O₄ interlayer spacing. TEM and SEM analyses show that LiV_0.15Mn_1.85O₄ has a smaller particle size and more regular morphological structure with narrow size distribution than LiMn₂O₄. It is concluded that the structural stability and cycle life improvement were due to many factors like better crystallinity, smaller particle size and uniform distribution compared to the LiMn₂O₄ cathode material. The LiV_0.15Mn_1.85O₄ cathode material has improved the structural stability and excellent electrochemical performances of the rechargeable lithium ion batteries.     

Physical properties of LiMn2O4 spinel prepared at moderate temperature

A moderate-temperature method of preparation of the spinel LiMn₂O₄ was developed around 500 °C. Physical features of the products were identified by X-ray photoelectron spectroscopy, X-ray diffractometry, Raman scattering and FTIR spectroscopy. The electronic conductivity of LiMn₂O₄ has been studied as a function of annealing temperature. The product LiMn₂O₄ is identified as a micron-sized powder and analysis of the local environment is in good accordance with the classical structural model of Fd3m space group. LiMn₂O₄ exhibits an electrical conductivity of 1.9×10⁻⁵ S/cm at room temperature with an activation energy of 0.16 eV which corresponds to an electron hopping mechanism between the two charge states of Mn³⁺ and Mn⁴⁺ ions. A first-order phase transition is observed at 292 K.     

Elevated electrochemical property of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> originated from nano-sized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>

By employment of nano-sized pre-prepared Mn₃O₄ as precursor, LiMn₂O₄ particles have been successfully prepared by facile solid state method and sol-gel route, respectively. And the reaction mechanism of the used precursors of Mn₃O₄ is studied. The structure, morphology, and element distribution of the as-synthesized LiMn₂O₄ samples are characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Compared with LiMn₂O₄ synthesized by facile solid state method (SS-LMO), LiMn₂O₄ synthesized by modified sol-gel route (SG-LMO) possesses higher crystallinity, smaller average particle size (~175 nm), higher lithium chemical diffusion coefficient (1.17 × 10^?11 cm² s^?1), as well as superior electrochemical performance. For example, the cell based on SG-LMO can deliver a capacity of 85.5 mAh g^?1 at a high rate of 5 °C, and manifests 88.3% capacity retention after 100 cycles at 0.5 °C when cycling at 45 °C. The good electrochemical performance of the cell based on SG-LMO is ascribed mainly to its small particle size, high degree of dispersion, and uniform element distribution in bulk material. In addition, the lower polarization potential accelerates Li⁺ ion migration, and the lower atom location confused degree maintains integrity of crystal structure, both of which can effectively improve the rate capability and cyclability of SG-LMO.     

Significance of Mg doped LiMn2O4 spinels as attractive 4 V cathode materials for use in lithium batteries

LiMn₂O₄ spinel is one of the most promising cathode materials for lithium-ion batteries because of its cheapness and eco-friendliness. Due to Jahn-Teller distortion, the capacity fades, however, upon repeated cycling. Attempts are being made to improve the cycle life of the spinel by substitution of manganese with other cations. In this paper we report the effect of partial substitution of manganese by Mg²⁺ ions in the LiMn₂O₄ phase. LiMg_yMn_2−yO₄ (y=0 – 0.3) has been synthesized by a thermal method and characterized using XRD, TG/DTA and FTIR. The electrochemical performance is correlated with the dopant concentration.     

An electrochemical study on the substituted spinel LiMn1.95Cr0.05O4

Cyclic voltammetry, galvanostatic charge?Cdischarge technique, potentiostatic intermittent titration technique (PITT), and electrochemical impedance spectroscopy (EIS) were used to study the behavior of a LiMn_1.95Cr_0.05O₄ (substituted lithium?Cmanganese spinel) electrode in nonaqueous electrolytes at 25 °C. Quantitative and qualitative changes of the electrode transport parameters as functions of lithium concentration were analyzed. Several equivalent circuits are discussed; the results obtained by different methods are compared. The PITT and EIS results are in good agreement; the chemical diffusion coefficient D varies within 10^?14?C10^?9 cm² s^?1 depending on the lithium content in the Li_xMn_1.95Cr_0.05O₄ electrode.     

An approach to improve the electrochemical performance of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> at high temperature

In order to overcome the severe capacity decay of LiMn₂O₄ at high temperature, TiN is used as an active materials additive in this paper. The XRD and XPS test results indicate that the TiN can effectively prevent Mn from dissolving in electrolyte; galvanostatic charge-discharge test shows that LiMn₂O₄ electrode with TiN exhibits remarkably improved capacity retention at high temperature with capacity of 105.1 mAh g^?1 at 1 C in the first cycle at 55 °C and the capacity maintains 88.9% retention after 150 cycles. And the electrochemical impedance spectroscopy result demonstrates TiN’s effectiveness in easing the increase of charge-transfer resistance during cycling. Therefore, we can conclude that TiN, as an addictive, made obvious contribution to the greatly improved electrochemical cycling performance of LiMn₂O₄.     

Precursor derived LiMn2O4 thin films as ionic conductor

Thin films of spinel LiMn₂O₄ have been fabricated using a metallorganic precursor. Crystalline films have been deposited on Au substrates to exhibit as the cathode in rechargeable thin film lithium batteries. The nucleation and growth of spinel LiMn₂O₄ crystallites were investigated with heat treatment of the deposited thin films. Film capacity density as high as 22 μAh/cm² was measured for LiMn₂O₄. The film heat treated at 700 °C were cycled electrochemically up to 30 cycles against Li metal without any degradation of the capacity. There were neither open area nor amorphous layers which prevent the Li⁺ions transfer at the boundaries in the LiMn₂O₄ thin film. The microscopic study revealed that (111) planes in the two grains directly bonded at the grain boundary which could proceed the lithium ion intercalation or deintercalation smoothly.     

Characterization and electrochemical performance of the spinel LiMn2O4 prepared from -MnO2

The preparation and characterization of the spinel LiMn₂O₄ obtained by solid state reaction from quasi-amorphous -MnO₂ is reported. A well-defined highly pure spinel was characterized from X-ray diffractograms. The average manganese valence of -MnO₂ and spinel samples was found to be 3.89±0.01 and 3.59±0.01, respectively. The electrochemical performance of the spinel was evaluated through cyclic voltammetry and chronopotentiometry. The voltammetric profiles obtained at 1 mV/s for the LiMn₂O₄ electrode in 1 M LiClO₄ dissolved in a 2:1 mixture of ethylene carbonate and dimethyl carbonate showed typical peaks for the lithium insertion/extraction reactions. The charge capacity of this electrode was found to be 110 mA h g⁻¹ for the first charge/discharge cycles.     

Surface modification of LiMn2O4 thin films at elevated temperature

In order to improve the cycle stability of spinel LiMn₂O₄ electrode at elevated temperature, the LiCoO₂-coated and Co-doped LiMn₂O₄ film were prepared by an electrostatic spray deposition (ESD) technique. LiCoO₂-coated LiMn₂O₄ film shows excellent cycling stability at 55 °C compared to pristine and Co-doped LiMn₂O₄ films. The samples were studied by X-ray diffraction, scanning electron microscopy, Auger electron spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy. The excellent performance of LiCoO₂-coated LiMn₂O₄ film can be explained by suppression of Mn dissolution. On the other hand, the LiCoO₂-layer on the LiMn₂O₄ surface allows a homogenous Li⁺ insertion/extraction during electrochemical cycles and improves its structure stability.