Enhanced antifouling performance of ZnS/GO/PVDF hybrid membrane by improving hydrophilicity and photocatalysis

In order to improve the antifouling performance of PVDF membrane, a novel zinc sulfide/graphene oxide/polyvinylidene fluoride (ZnS/GO/PVDF) composite membrane was prepared by immersed phase inversion method. The surface morphology, crystal structure, photocatalytic activity, and antifouling property of the as‐prepared membranes were systematically studied. Results showed that the ZnS/GO/PVDF hybrid membranes were successfully fabricated with uniform surface. The hybrid membrane surface possessed higher hydrophilicity with water contact angle decreasing from 77.1° to 62.2°. The permeability of the hybrid membrane was therefore enhanced from 222.9 to 326.1 L/(m² hour). Moreover, bovine serum albumin (BSA) retention experiment showed that the hybrid membrane separation was also promoted by 7.2%. The blending of ZnS and GO enhanced the hydrophilic and photocatalytic performances of PVDF membrane, which mitigated the membrane fouling effectively. This novel hybrid membrane could accelerate the practical application of photocatalytic technology in membrane separation process.     

Versatility of hydrophilic and antifouling PVDF ultrafiltration membranes tailored with polyhexanide coated copper oxide nanoparticles

Hydrophilic poly(vinylidene fluoride) (PVDF) nanocomposite ultrafiltration (UF) membranes with excellent antifouling and antibiofouling characteristics are fabricated by employing polyhexanide coated copper oxide nanoparticles (P–CuO NPs). The presence of P–CuO NPs is played a significant role in altering the PVDF membrane matrix and probed by XRD, FTIR, FESEM and contact angle analysis. The PVDF/P–CuO nanocomposite membranes exhibited an outstanding antifouling performance indicated by the superior pure water flux, effective foulant separation and maximum flux recovery ratio during UF experiments as a result of the formation of the hydrophilic and more porous membrane due to the uniform distribution of P–CuO NPs. Particularly, the PVDF/P–CuO-3 membrane showed higher PWF of 152.5 ± 2.4 lm⁻²h⁻¹ and porosity of 64.5% whereas the lower contact angle of 52.5°. Further, it showed the higher rejection of 99.5 and 98.4% and the flux recovery ratio of 99.5 and 98.5% respectively for BSA and HA foulants, demonstrated its increased water permeation, foulant separation and antifouling behavior. Further, the decent antibacterial activity is showed by the PVDF/P–CuO nanocomposite membranes with the formation of halo-zone around the membrane when exposed to the bacterial medium demonstrated that, by this process an antibacterial water treatment membrane can be developed by simple phase inversion technique with good membrane stability.     

pH stimuli-responsive and fouling resistance PES membrane fabricated by using photochromic spiropyran and spironaphthoxazine nanofillers for pesticide removal

New fouling resistance and stimulus–responsive nanofiltration membranes were fabricated by adding photochromic spiropyran (SPO) and spironaphthoxazine (SNO) nanofillers to the polyethersulfone (PES) matrix via the phase inversion method. The effect of SPO and SNO, as novel photoresponsive molecule nanofillers, were evaluated in terms of membrane morphology, porosity, wettability, pure water flux (PWF), antifouling resistance, and stimulus–responsive properties. All the modified membranes indicated better performance compared to the bare PES. The membrane PWF was notably enhanced from 7.7 kg/m²h for the bare PES up to 18.68 and 20.58 kg/m²h for the 0.1 wt.% SPO and SNO blended membranes, respectively. Also, the 0.1 wt.% of SNO-based PES membrane indicated the best flux recovery ratio compared to the other membranes. The photo stimulus–responsive assessment showed a color change for both SPO and SNO photochromic in membranes. In the case of variable effect investigation, the response surface methodology at three levels (pressure: 4, 5, 6 bar and flow rate: 50, 100, and 150 L/h) was applied. A suitable flux (23.39 kg/m² h) and high removal efficiency (more than 90%) was achieved at optimum conditions. Also, the modified membranes by photochromic materials were sensitive to environmental variables such as acidic and alkaline conditions by changing their color.     

The effect of heat treatment of PES and PVDF ultrafiltration membranes on morphology and performance for milk filtration

The flat sheet polyethersulfone (PES) and poly(vinylidene fluoride) (PVDF) membranes were prepared by immersion precipitation technique. The influence of hot air and water treatment on morphology and performance of membranes were investigated. The membranes were characterized by AFM, SEM, cross-flow filtration of milk and fouling analysis. The PES membrane turns to a denser structure with thick skin layer by air treatment at various temperatures during different times. This diminishes the pure water flux (PWF). However the milk permeation flux (MPF) was considerably improved at 100 °C air treatment for 20 min with no change in protein rejection. The smooth surface and slight decrease in surface pore size for air treated PES membrane at 100 °C compared to untreated membrane may cause this behavior for the membrane. The water treatment of PES membranes at 55 and 75 °C declines the PWF and MPF and increases the protein rejection. This is due to slight decrease in membrane surface pore size. The treatment of PES membrane with water at higher temperature results in a porous structure with superior performance. The fouling analysis of 20 min treated membrane indicates that the surface properties of 100 °C air treated and 95 °C water treated PES membranes are improved compared to untreated membrane. The SEM observation depicts that the morphology of air and water treated PVDF membranes was denser and smoother with increasing the heat treatment temperature. The 20 min air treated PVDF membranes at 100 °C and water treated at 95 °C exhibited the highest performance and antifouling properties.     

Cellulose acetate nanocomposite ultrafiltration membranes tailored with hydrous manganese dioxide nanoparticles for water treatment applications

Hydrous manganese dioxide (HMO) nanoparticles incorporated cellulose acetate (CA) composite ultrafiltration (UF) membranes are prepared with the aim of improving the water permeation and BSA contaminant removal. The HMO nanoparticles are synthesized from manganese ion and characterized by FT‐IR, XRD, and FESEM. The effect of variation of HMO on CA membranes is probed using FT‐IR, EDAX, contact angle, SEM, and AFM analysis to demonstrate their chemical functionality, hydrophilicity, and morphology. CA/HMO membranes are showing the enhancement in pure water flux (PWF), water uptake, porosity, hydrophilicity, fouling resistance, BSA rejection, and flux recovery ratio (FRR). CA‐1 membrane displayed higher PWF (143.6 Lm²h^?1), BSA rejection (95.9%), irreversible fouling (93.3%), and FRR (93.3%). Overall results confirmed that the CA/HMO nanocomposite UF membranes overcome the bottlenecks and shows potential for water treatment applications.     

具有抗菌性能的载药复合微纳米纤维的制备及其结构和性能表征

利用静电纺丝技术制备了一种具有抗菌性能的氧化锌(ZnO)/聚乳酸(PLA)/聚己内酯(PCL)载药微纳米纤维膜,并通过扫描电子显微镜(SEM)、X射线衍射(XRD)和傅里叶变换红外光谱(FTIR)分别对复合膜的表面形态、元素组成和化学结构进行表征。通过抗菌实验评价了复合膜的抗菌性能,用紫外分光光度计测试复合膜在体外的药物释放行为。结果显示,以物理共混的方式将ZnO和氢溴酸高乌甲素(LAH)成功载入复合微纳米纤维;与PLA/PCL复合微纳米纤维膜相比,ZnO/PLA/PCL复合微纳米纤维膜表现出更好的抗菌效率。当ZnO含量为10%(wt)时,复合微纳米纤维膜具有最佳的抗菌性能;药物释放性能结果表明,ZnO/PLA/PCL复合微纳米纤维膜具有良好的药物缓释性能。     

Preparation and Evaluation of iPP/GO Microfiltration Membrane with Enhanced Antifouling Property

Isotactic polypropylene(iPP) and graphene oxide(GO), dispersed in dibutyl phthalate(DBP) and dioctyl phthalate(DOP), were blended to prepare organic-inorganic-blended microfiltration membranes using thermally induced phase separation(TIPS). These membranes were characterized by scanning electron microscopy(SEM), Fourier transform infrared spectroscopy(FTIR), contact angle measurements, mechanical properties, permeation tests, and porosity measurements. The morphology studied by SEM shows larger pores of the GO-blended membranes when compared to those of unmodified iPP membranes. Composite iPP/GO membranes achieve better performance in terms of water fluxes and pure water fluxes recovery ratio due to the hydrophilic nature of GO when compared with the pure iPP membranes. The addition of GO increases the permeability and the tensile strength by 352.98% and 123%, respectively, and also decreases the contact angle from 125° to 52.33°. We concluded that the composite membrane with 0.3% GO has the best antifouling ability of the membranes tested because it has the highest values of mean pore radius, porosity, and water flux observed in this study.     

Influence of Polymer Solvents on the Properties of Halloysite-Modified Polyethersulfone Membranes Prepared by Wet Phase Inversion

Ultrafiltration polyethersulfone (PES) membranes were prepared by wet phase inversion. Commercial halloysite nanotubes (HNTs) in the quantities of 0.5 wt% vs. PES (15 wt%) were introduced into the casting solution containing the polymer and different solvents: N,N-dimethylformamide (DMF), N,N-dimethylacetamide (DMA), or 1-methyl-2-pyrrolidinone (NMP). The type of solvent influenced the membranes’ morphology and topography, as well as permeability, separation characteristics, and antifouling and antibacterial properties. The membranes prepared using DMA exhibited the loosest cross-section structure with the thinnest skin and the roughest surface, while the densest and smoothest were the DMF-based membranes. The advanced contact angles were visibly lower in the case of the membranes prepared using DMF compared to the other solvents. The highest water permeability was observed for the DMA-based membranes, however, the most significant effect of the modification with HNTs was found for the NMP-based series. Regardless of the solvent, the introduction of HNTs resulted in an improvement of the separation properties of membranes. A noticeable enhancement of antifouling performance upon application of HNTs was found only in the case of DMF-based membranes. The study of the antibacterial properties showed that the increase in surface roughness had a positive effect on the inhibition of E. coli growth.     

Nanostructured polyethersulfone membranes for dye and protein separation: Exploring antifouling role of holmium (III) molybdate nanosheets

Nanostructured polymer membranes are nowadays of crucial importance in achieving antifouling properties. Nanomaterials with tunable composition, size, and morphology, surface modification and functionality offer unprecedented opportunities for efficient wastewater treatment. In this work, the effect of holmium (III) molybdate (Ho₂MoO₆) nanomaterial as a new nanofiller on preparation of nanostructured polyethersulfone (PES) mixed matrix membranes was examined in terms of hydrophilicity, membrane morphology, permeability, dye and protein separation and antifouling property. The Ho₂MoO₆ nanosheets were synthesized and characterized by FTIR, XRD, and FESEM and used in different amounts in PES matrix. The pore size and the membrane porosity increased with Ho₂MoO₆ loading. The nanocomposite membranes showed enhancement in hydrophilicity, antifouling properties, dye rejection and permeability. The remarkably pure water flux (195 L/m²h at 3 bar) and 92.3% flux recovery after bovine serum albumin (BSA) filtration were obtained for the membrane mixed with 2 wt% Ho₂MoO₆ compared to 95 L/m²h and 75.2% obtained for the bare PES, respectively. Moreover, significantly high rejection of Acid Red 125 (95 ± 1%) was achieved. Thus, the experimental results established the potential efficiency of the novel nanocomposite membrane for the separation applications.     

Regulation of the microstructure of polyvinylidene fluoride membrane via incorporation of nano-ZIF-7 for improving hydrophobicity and antiwetting performance

The design and fabrication of a membrane with super hydrophobicity and antiwetting property is of great importance for improving membrane performance in distillation, desalination, gas absorption, and separation. In this work, polyvinylidene fluoride (PVDF) membranes were modified by Zeolitic Imidazolate Framework-7 (ZIF-7) nanocrystals to improve the hydrophobic property and antiwetting performance. ZIF-7/PVDF hybrid membranes were prepared via the nonsolvent-induced phase separation (NIPS) method. Different concentrations of ZIF-7 nanocrystals (0, 0.5, 1, 2, 3, and 5 wt%) were introduced into the PVDF dope solution, and the physical structure of the resulting membranes were systematically characterized. Due to the hydrophobic nature of ZIF-7 nanocrystals, the solvent–nonsolvent exchange rate had been regulated effectively during phase inversion. The morphology of top and bottom surfaces, together with the inner structures of the hybrid membrane, has been changed obviously, showing a more twisted finger-like macrovoid layer and a thicker sponge-like layer compared to pristine PVDF membrane. Furthermore, the hydrophobicity and antiwetting properties of these hybrid membranes improved obviously when the incorporated concentration of ZIF-7 was higher than 1 wt%. The M(2) membrane, which possessed the highest surface roughness and water contact angles, showed the best antiwetting property and recovered gas permeance ratio (>95%) after being immersed in aqueous solution for 10 hr.     

Fabrication of Defect-Engineered MOF-801 Membrane for Efficient Dye Rejection

Although having shown great promise for efficient water treatment, rational structural design and engineering of polycrystalline MOF membranes remain rarely investigated so far. In this study, we prepared well-intergrown MOF-801 membranes with tailorable structural deficiencies in the framework for application in dye rejection. Of particular note, we found that the addition of formic acid as modulator led to the formation of MOF-801 membrane with higher missing-linker number, which was beneficial for increasing water flux with little compromise in dye rejection rate. The MOF-801 membrane prepared in this work exhibited excellent dye rejection performance (CR rejection rate of 99.50 % and water flux of 31.69 L m⁻² h⁻¹ bar⁻¹) as well as excellent long-term stability.     

Influence of the polyacyl chloride structure on the reverse osmosis performance,surface properties and chlorine stability of the thin-film composite polyamide membranes

This paper aims to study the structure–property relationship and make several reasonable suggestions for tailoring special separation performance and surface properties of thin-film composite polyamide membranes. In the experiments, composite membranes of different thin films with small structural differences were prepared through interfacial polymerization of trimesoyl chloride (TMC), 5-isocyanato-isophthaloyl chloride (ICIC), and 5-chloroformyloxy-isophthaloyl chloride (CFIC) with m-phenylenediamine (MPD) separately, after which their reverse osmosis performances were evaluated by permeation experiment with salt aqueous solution, and film properties were characterized by AFM, SEM, XPS, ATR-IR, contact angle and streaming potential measurements. Chlorine stability was also studied through the evaluation of membrane performance before and after hypochlorite exposure. The results show that the polyacyl chloride structure strongly influences the reverse osmosis performance, surface properties and chlorine stability of the composite membranes; that the introduction of isocyanato group into polyacyl chloride improves the hydrophilicity, water permeability and surface smoothness of the thin-film composite membrane, and increases the absolute value of zeta potential at both low and high pH, but reduces the chlorine stability; and that the introduction of chloroformyloxy group increases the salt rejection rate and the surface roughness of the composite membrane, but lowers the water permeability.     

Effect of Polyethylene glycol methyl ether blend Humic acid on poly (vinylidene fluoride-co-hexafluropropylene) PVDF-HFP membranes: pH responsiveness and antifouling behavior with optimization approach

Flat sheet asymmetric membranes were fabricated with homogeneous solution of poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) using N-methyl-2-pyrrolidone (NMP) as solvent via phase inversion method. PEGME (Poly ethylene glycol methyl ether) (M_n 5000) blend Humic Acid (HA), of different mole ratio was used as additive. Characterization of the membranes was done by Field emission scanning electron microscope (FESEM), Fourier Transform Infrared (FTIR) spectroscopy, Atomic force microscopy (AFM) and Differential scanning calorimetry (DSC) studies. Liquid-liquid displacement porosimetry (LLDP) study evaluated the morphological parameters, average pore size and pore size distribution. Bovine serum albumin (BSA) (M_W - 68,000 Da) was used to study the antifouling effect and pore blocking mechanism of the membranes. The pure water flux (PWF), solute rejection and flux recovery ratio drastically increases for the PEGME blended HA membranes whereas the water contact angle decreases significantly. The pH responsiveness character of the prepared membranes altered the hydraulic permeability and rejection % at different pH. Finally, optimization of the variables contributing towards the PWF and BSA rejection of the desired membrane was performed using Design expert software 9.0 TRIAL through ANOVA (analysis of variance) using the combination of response surface methodology (RSM) and central composite design (CCD).     

Antibacterial ultrafiltration membrane with silver nanoparticle impregnation by interfacial polymerization for ballast water

Interfacial polymerization technology was employed to immobilize silver (Ag) nanoparticles on the surface of commercial polyethersulfone (PES) membrane to develop antibacterial and antifouling ultrafiltration membrane. Ag nanoparticles were prepared from the reduction of silver nitrate (AgNO₃) by sodium borohydride in the presence of polyethyleneimine (PEI) as the stabilizer. The encapsulated Ag nanoparticles in the PEI solution were embedded into the PEI membrane when trimesoyl chloride solution was used to crosslink the PEI solution with the PES membrane, forming Ag-polyamide (PA) networks through the interfacial polymerization reaction. Experimental results showed that the membrane prepared with 50 mmol/L of AgNO₃ and 20 mmol/L of PEI had the optimized antibacterial effect against Escherichia coli. Bacterial concentration and species were also investigated. Exiguobacterium aestuarii and Staphylococcus aureus which are gram-positive bacteria, needed significantly more time for the Ag-PA/PES membrane to kill the bacteria completely when compared to E.coli and Vibrio coralliilyticus which are gram-negative bacteria. This study showed that Ag nanoparticles impregnated in membrane surfaces were 100% effective in killing various types of marine bacteria and bacteria in the seawater collected off Sentosa Island in Singapore. These membranes exhibit excellent antibacterial and antifouling properties which can be used to kill bacteria in ballast water and seawater.     

基于多巴胺自聚合与表面接枝PHGH制备抗菌纳滤膜

在水溶液中将聚六亚甲基单胍盐酸盐(PHGH)共价接枝在经多巴胺自聚合改性的聚砜膜表面, 制备具有抗菌性能的纳滤膜. 采用全反射红外光谱(ATR-FTIR)、 扫描电子显微镜(SEM)和接触角测试考察膜表面的结构、 形貌和亲水性变化. 探讨PHGH含量对膜的接枝度及分离性能的影响, 并对膜的抗菌性能进行了评价. 结果表明, 经过多巴胺的自聚合和表面接枝PHGH后, 聚砜膜表面形成了具有纳滤分离性能的活性层, 并且膜表面亲水性得到改善. 随着PHGH含量的增大, 膜的纯水通量降低, 而对无机盐和染料的截留性能提高. 接枝后的复合膜具有较高的抗菌性能, 当PHGH含量为3%(质量分数)时, 抗菌率可达98.5%.     

二维复合光催化剂的合成及其性能研究

摘要：通过超声辅助溶剂热法制备一种新型的二维类复合光催化剂BiOCl/MOF-5。运用XRD、SEM、BET、TEM、PL 等手段对催化剂的特殊结构和性能进行表征。在该光催化剂体系中,选取MOF-5为载体,通过与光催化剂BiOCl复合来合成一种新型的二维复合光催化剂。 结果表明,制备的催化剂均呈现出较为明显的二维形貌,且相对与单一BiOCl (3.15 mg2?g-1 )来说,该复合催化剂 (110.16 mg2?g-1 ) 的比表面积得到了明显的提高。由于催化剂的光催化性能与其比表面积和孔隙体积密切相关。复合催化剂相对较大的比表面积和适当的能带隙,有利于为反应物提供更多的活性位点和有效的传输路径,而且得益于MOF-5独特的形貌和结构,光催化剂聚集和比表面积小的问题也得到了解决。因此,该复合材料在降解有机物方面呈现出优异的光催化活性,且与纯BiOCl相比,催化剂的光催化活性得到了明显的提高。     

Development of urethane acrylate composite ion-exchange membranes and their electrochemical characterization

With the objective of introducing antifouling characteristics into interpolymer types of cation and anion exchange membranes, the surface of these membranes was coated with a 12-microm-thick urethane acrylate layer and was cured by UV radiation of wavelengths 308 and 172 nm under a complete inert atmosphere. Different urethane acrylate composite ion exchange membranes developed were characterized in NaCl solution by measuring their ion-exchange capacity, volume fraction of water, contact angle with water, membrane conductance, and membrane potential. It was found that the electrochemical transport properties of urethane acrylate composite cation-exchange membranes were increased due to resonance stabilization of the urethane group, which acts as a weak acid and dissociates as a negatively charged urethane ion and a positively charged proton. This contributes toward the net charge density of the membrane matrix responsible for enhanced selectivity and conductivity, while for urethane acrylate composite anion-exchange membranes reduction in net charge density was responsible for reduction in electrochemical transport properties. Counterion transport number, permselectivity, and counterion diffusion coefficient values for these membranes were also estimated. Experiments were also carried out in higher homologs of sodium carboxylate solutions in order to observe the fouling tendencies of these membranes. It was concluded that it is possible to obtain antifouling characteristics of ion-exchange membranes by coating and curing thin hydrophilic layers of urethane acrylate on their surfaces without sacrificing their electrochemical transport properties.     

g-C3N4基复合分离膜的制备及光催化性能

利用g-C₃N₄纳米片表面的氨基与膜基底材料氯甲基化聚醚砜（CMPES）的苄氯基团发生化学交联反应,再通过相转化法制备出g-C₃N₄/CMPES复合膜。系统研究了g-C₃N₄纳米片的添加对复合膜的结构、形貌及过滤、光催化、抗污染性能的影响,并探讨其光催化降解牛血清白蛋白溶液（BSA）的机理。研究结果表明：g-C₃N₄纳米片与膜基底材料通过化学键相连接,有效提高了复合膜的光催化性能和稳定性。由于g-C₃N₄纳米片的亲水性和光催化作用,使复合膜表现出优异的过滤性能和抗污染性能。     

Enhancing the antifouling property of polyethersulfone ultrafiltration membranes through surface adsorption-crosslinking of poly(vinyl alcohol)

An adsorption-crosslinking process of poly(vinyl alcohol) (PVA) was introduced to modify the surface of polyethersulfone (PES) ultrafiltration membranes for enhancement of their antifouling property. XPS and water contact angle measurement confirmed the obvious enhancement of surface hydrophilicity. Ultrafiltration results showed that the spreading of PVA chains over the hydrophobic membrane surface caused substantial but acceptable decrease on membrane flux. The fouling type analysis indicated that PVA adsorption effectively improved the antifouling property of PES membranes. With a PVA concentration of 0.5 wt% and three cycles of alternative adsorption-crosslinking, the total and irreversible fouling ratio of modified membranes were 0.38 and 0.22, respectively, much lower than those of control PES membrane (0.61 and 0.47), and the flux recovery ratio was increased accordingly. The long-term ultrafiltration experiment demonstrated the improvement of recycling property and the reliability of adsorption-crosslinking process.     

Fabrication,characterization, and performance evaluation of polyethersulfone/TiO2 nanocomposite ultrafiltration membranes for produced water treatment

In the present work, development of neat and nanocomposite polyethersulfone membranes composed of TiO₂ nanoparticles is presented. Membranes are fabricated using nonsolvent phase inversion process with the objective of improving antifouling, hydrophilicity, and mechanical properties for real and synthetic produced water treatment. Membranes are characterized using scanning electron microscopy, Fourier‐transform infrared, contact angle, porosity measurement, compaction factor, nanoparticles stability, and mechanical strength. The performance of prepared membranes was also characterized using flux measurement and oil rejection. Fourier‐transform infrared spectra indicated that noncovalence bond formed between Ti and polyethersulfone chains. The contact angle results confirmed the improved hydrophilicity of nanocomposite membranes upon addition of TiO₂ nanoparticles owing to the strong interactions between fillers and water molecules. The increased water flux for nanocomposite membranes in comparison with neat ones can be due to coupling effects of improved surface hydrophilicity, higher porosity, and formation of macrovoids in the membrane structure. The membrane containing 7 wt% of TiO₂ nanoparticles was the best nanocomposite membrane because of its high oil rejection, water flux, antifouling properties, and mechanical stability. The pure water flux for this membrane was twice greater than that of neat membrane without any loss in oil rejection. The hydrophilicity and antifouling resistance against oil nominates developed nanocomposite membranes for real and synthetic produced water treatment applications with high performance and extended life span.