低成本富勒烯衍生物电子传输层在钙钛矿太阳能电池的应用

Organic-inorganic hybrid perovskite solar cells (PSCs) have attracted significant attention owing to their high absorption coefficient and ambipolar charge transport properties. With only several years of development, the power conversion efficiency (PCE) has increased from 3.8% to 22.7%. In general, PSCs have two types of structural architecture: mesoporous and planar. The latter possesses higher potential for commercialization due to its simpler structure and fabrication process, especially the inverted planar structure, which possesses negligible hysteresis. In an inverted PSC, the electron transport materials (ETM) are deposited on a perovskite film. Only a few ETMs can be used for inverted PSCs as the perovskite film is easily damaged by the solvent used to dissolve the ETM. Furthermore, the energy levels of the ETM should be well aligned with that of the perovskites. Normally it is difficult to use inorganic ETMs as they require high temperatures for the annealing process to improve the electron conductivity; the perovskite film cannot sustain these high temperatures. To date, the fullerene derivative, [6, 6]-phenyl-C61-butyric acid methyl ester (PCBM), is the most commonly used organic ETM for high efficiency inverted planar PSCs. However, the high manufacturing cost due to its complex synthesis retards the industrialization of the PSCs. Here, we introduce a fullerene pyrrolidine derivative, N-methyl-2-pentyl-[60]fullerene pyrrolidine (NMPFP), synthesized via the Prato reaction of C₆₀ directly with cheap hexanal and sarcosine. Then the NMPFP electron transport layer (ETL) was prepared by a simple solution process. The properties of the resulting NMPFP ETLs were characterized using UV-Vis absorption spectroscopy, cyclic voltammetry measurements, atomic force microscopy, and conductivity test. From the results of the UV-Vis absorption spectroscopy and cyclic voltammetry measurements, the LUMO level of NMPFP ETL was calculated to be 0.2 eV higher than that of the PCBM ETL. This contributes to a higher open-circuit photovoltage. In addition, the NMPFP film presented higher conductivity than the PCBM film. Thus, the photo-generated charge carriers in the perovskite films should be transported more efficiently to the NMPFP electron transport layer (ETL) than to the PCBM ETL. This was confirmed by the results of the steady-state photoluminescence spectroscopy. Finally, the NMPFP as an alternative low-cost ETL was employed in an inverted planar PSC to evaluate the device performance. The device made with the NMPFP ETL yielded an efficiency of 13.83% with negligible hysteresis, which is comparable to the PCBM counterpart devices. Moreover, since stability is another important parameter retarding the commercialization of PSCs, the stability of the PCBM and NMPFP base PSCs were investigated and compared. It was found that the NMPFP devices possessed significantly improved stability due to the higher hydrophobicity of the NMPFP. In conclusion, this research demonstrates that NMPFP is a promising ETL to replace PCBM for the industrialization of cheap, efficient and stable inverted planar PSCs.     

Inkjet Printing and Instant Chemical Transformation of a CH3NH3PbI3/Nanocarbon Electrode and Interface for Planar Perovskite Solar Cells

A planar perovskite solar cell that incorporates a nanocarbon hole‐extraction layer is demonstrated for the first time by an inkjet printing technique with a precisely controlled pattern and interface. By designing the carbon plus CH₃NH₃I ink to transform PbI₂ in situ to CH₃NH₃PbI₃, an interpenetrating seamless interface between the CH₃NH₃PbI₃ active layer and the carbon hole‐extraction electrode was instantly constructed, with a markedly reduced charge recombination compared to that with the carbon ink alone. As a result, a considerably higher power conversion efficiency up to 11.60 % was delivered by the corresponding solar cell. This method provides a major step towards the fabrication of low‐cost, large‐scale, metal‐electrode‐free but still highly efficient perovskite solar cells.     

界面修饰策略在钙钛矿太阳能电池中的应用

目前钙钛矿太阳能电池的认证效率已达25.2%,被认为是下一代最有希望的薄膜太阳能电池候选者。但通过溶液加工方法制备的钙钛矿薄膜不可控的形貌与较差的结晶性是制约器件稳定性提升和大面积生产的主要原因。为了有效解决这一难题,研究者们通常在电荷传输层与钙钛矿层之间进行界面修饰。本文从界面修饰的角度出发,总结了不同界面修饰策略在钙钛矿太阳能电池中的应用,并展望了界面修饰在低成本和大面积钙钛矿太阳能电池的应用前景。     

基于1D/0D有序复合SnO2纳米晶的钙钛矿太阳能电池

通过水热前驱体中的功能添加剂调控一维(1D)纳米棒阵列疏密度,继而在纳米棒间隙沉积零维(0D)纳米颗粒,制备1D/0D有序的复合SnO2电子传输层(ETL),并组装高效、稳定的钙钛矿太阳能电池。系统研究前驱体中NaCl添加剂以及后续纳米颗粒的沉积对复合ETL的形貌结构、光谱性能及界面电荷过程的作用规律,探讨上述作用对电池光电性能的影响机制。前驱体中NaCl的加入使棒密度变小,从而使0D纳米颗粒顺利渗透到1D纳米棒间隙中,其对钙钛矿/ETL和钙钛矿/FTO界面复合的抑制作用是造成器件开路电压和填充因子增大的原因。在经2 mL饱和NaCl水溶液改性的1D电子传输层ETL-2Cl的基础上,继续沉积0D的纳米颗粒,制备得到新型1D/0D复合电子传输层ETL-2P,后者优良的电荷复合抑制作用(复合电阻是ETL-2Cl的2.9倍)和高效的电子抽提性能(抽提速率3.03×10^7 s^-1,抽提效率91.6%)促成了电池较优的光电性能(光电效率12.15%)。     

Graphdiyne: Bridging SnO2 and Perovskite in Planar Solar Cells

The matching of charge transport layer and photoactive layer is critical in solar energy conversion devices, especially for planar perovskite solar cells based on the SnO₂ electron‐transfer layer (ETL) owing to its unmatched photogenerated electron and hole extraction rates. Graphdiyne (GDY) with multi‐roles has been incorporated to maximize the matching between SnO₂ and perovskite regarding electron extraction rate optimization and interface engineering towards both perovskite crystallization process and subsequent photovoltaic service duration. The GDY doped SnO₂ layer has fourfold improved electron mobility due to freshly formed C?O σ bond and more facilitated band alignment. The enhanced hydrophobicity inhibits heterogeneous perovskite nucleation, contributing to a high‐quality film with diminished grain boundaries and lower defect density. Also, the interfacial passivation of Pb?I anti‐site defects has been demonstrated via GDY introduction.     

Localized Oxidation Embellishing Strategy Enables High-Performance Perovskite Solar Cells

Perovskite solar cell (pero-SC) has attracted extensive studies as a promising photovoltaic technology, wherein the electron extraction and transfer exhibit pivotal effect to the device performance. The planar SnO₂ electron transport layer (ETL) has contributed the recent record power conversion efficiency (PCE) of the pero-SCs, yet still suffers from surface defects of SnO₂ nanoparticles which brings energy loss and phase instability. Herein, we report a localized oxidation embellishing (LOE) strategy by applying (NH₄)₂CrO₄ on the SnO₂ ETL. The LOE strategy builds up plentiful nano-heterojunctions of p-Cr₂O₃/n-SnO₂ and the nano-heterojunctions compensate the surface defects and realize benign energy alignment, which reduces surface non-radiative recombination and voltage loss of the pero-SCs. Meanwhile, the decrease of lattice mismatch released the lattice distortion and eliminated tensile stress, contributing to better stability of the devices. The pero-SCs based on α-FAPbI₃ with the SnO₂ ETL treated by the LOE strategy realized a PCE of 25.72 % (certified as 25.41 %), along with eminent stability performance of T₉₀>700 h. This work provides a brand-new view for defect modification of SnO₂ electron transport layer.     

2D钙钛矿太阳能电池的能带调控

经过短短十年的发展,钙钛矿太阳能电池效率已经超过25%,极具商业化价值,这得益于三维(3D)钙钛矿材料具有合适的带隙、吸光系数高、电子迁移距离长等优点。但3D钙钛矿的稳定性依然是其亟待解决的问题。二维(2D)钙钛矿器件除了兼具3D钙钛矿的优异光电性质之外,其稳定性良好,是解决3D钙钛矿太阳能电池稳定性问题的一个可行方案。2D钙钛矿晶格中的疏水性大烷基胺阳离子能阻止湿气侵入的可能路径,使其成为光电器件的备选材料。由于2D钙钛矿对许多不同的有机和无机成分具有较高的耐受性,使其组成具有多样性,进而影响其能带变化。本文对2D钙钛矿的带隙调控及能带调控进行总结,希望对制备高效、稳定的低维度钙钛矿太阳能电池具有一定的指导意义。     

通过磁控溅射金属钛生长金红石型二氧化钛纳米片阵列应用于钙钛矿太阳能电池

本文首次通过磁控溅射方法,在FTO表面溅射一层Ti金属层,结合水热反应,原位生长TiO₂纳米片阵列（TiO₂ NSAs）. 经过退火处理,Ti金属层转变为致密的TiO₂层,因此基于此方法制得的金红石型TiO₂ NSAs与FTO基底具有很强的结合力. 与通过原子层沉积 (ALD) 以及悬涂 (SC) 法所得的另外两种TiO₂致密层生长的TiO₂ NSAs对比发现,基于本文所述方法制备的TiO₂ NSAs作为支架层的钙钛矿太阳能电池具有最佳性能. 上述结果主要是由于该TiO₂ NSAs无明显缺陷,并且在TiO₂ NSAs/TiO₂致密层/FTO界面接触很好. 值得注意的是,通过优化实验条件,基于此种TiO₂ NSAs的钙钛矿太阳能电池的最高光电转换效率可达11.82%.     

The Effect of Lithium Doping in Solution-Processed Nickel Oxide Films for Perovskite Solar Cells

The effect of substitutional Li doping into NiO_x hole transporting layer (HTL) for use in inverted perovskite solar cells was systematically studied. Li doped NiO_x thin films with preferential crystal growth along the (111) plane were deposited using a simple solution-based process. Mott-Schottky analysis showed that hole carrier concentration (N_A) is doubled by Li doping. Utilizing 4 % Li in NiO_x improved the power conversion efficiency (PCE) of solar devices from 9.0 % to 12.6 %. Photoluminescence quenching investigations demonstrate better hole capturing properties of Li:NiO_x compared to that of NiO_x, leading to higher current densities by Li doping. The electrical conductivity of NiO_x is improved by Li doping. Further improvements of the device were made by using an additional ZnO layer onto PCBM, to remove shunt paths, leading to a PCE of 14.2 % and a fill factor of 0.72.     

Enhanced Performance of Camphorsulfonic Acid-Doped Perovskite Solar Cells

High-quality perovskite film with large grains and therefore reduced grain boundaries plays a significant role in improving the power conversion efficiency (PCE) and ensuring good long-term stability of the perovskite solar cells. In this work, we found that adding camphorsulfonic acid (CSA), a Lewis base, to the perovskite solution results in the crystallization of larger perovskite grains. By varying the concentration of CSA, we found that the optimal concentration of the additive is 1 mg/mL, which leads to an 20% increase in PCE of the cells compared to the reference CSA-free cell. Interestingly, we observed that the PCE of cells with an excess of CSA was initially poor, but may increase significantly over time, possibly due to CSA migration to the hole-transporting layer, leading to an improvement in its conductivity.     

Brookite TiO2 Nanoparticle Films for Dye‐Sensitized Solar Cells

Brookite TiO₂ nanoparticles have been synthesized at low temperature by a soft solution growth method and have been used as building blocks to prepare pure brookite nanoparticle porous films. The film brookite structure was confirmed by XRD and Raman spectroscopy. By spectrophotometry, it was shown that the films had a direct band gap of 3.4 eV. After sensitization by the N719 dye, efficient cells have been produced. A best overall conversion efficiency of 5.97 %, without a scattering layer, was found for the larger TiO₂ starting nanoparticles. The cell open‐circuit voltage was improved compared with that of anatase cells and a lower electron diffusion coefficient was found in the photoanodes made of smaller brookite particles. Lanthanum‐doped brookite nanoparticle films were also studied. They showed a marked decreased in the amount of dye loading, and hence, the solar cells had a reduced current density that was not compensated for by the increased open‐circuit voltage of the cells.     

Lithium‐Ion Endohedral Fullerene (Li+@C60) Dopants in Stable Perovskite Solar Cells Induce Instant Doping and Anti‐Oxidation

Herein, we report use of [Li⁺@C₆₀]TFSI^? as a dopant for spiro‐MeOTAD in lead halide perovskite solar cells. This approach gave an air stability nearly 10‐fold that of conventional devices using Li⁺TFSI^?. Such high stability is attributed to the hydrophobic nature of [Li⁺@C₆₀]TFSI^? repelling moisture and absorbing intruding oxygen, thereby protecting the perovskite device from degradation. Furthermore, [Li⁺@C₆₀]TFSI^? could oxidize spiro‐MeOTAD without the need for oxygen. The encapsulated devices exhibited outstanding air stability for more than 1000 h while illuminated under ambient conditions.     

Functional Metal Oxides in Perovskite Solar Cells

As extremely important inorganic materials, metal oxides play an irreplaceable role in solid perovskite solar cells. In this review, the preparation methods of metal oxides, their effects on the perovskite optoelectronic devices incorporated with the energy level compatibility of perovskite materials are provided. Finally, the possible reactions between interfaces during growth progress as well as passivation mechanism of some metal oxides to perovskite materials are discussed. The physical, chemical, and electrical properties of functional metal oxides endow the enhancement of the efficiency and stability of perovskite photovoltaic devices.     

Lithium Polystyrene Sulfonate as a Hole Transport Material in Inverted Perovskite Solar Cells

Despite the exceptional efficiency of perovskite solar cells (PSCs), further improvements can be made to bring their power conversion efficiencies (PCE) closer to the Shockley-Queisser limit, while the development of cost-effective strategies to produce high-performance devices are needed for them to reach their potential as a widespread energy source. In this context, there is a need to improve existing charge transport layers (CTLs) or introduce new CTLs. In this contribution, we introduced a new polyelectrolyte (lithium poly(styrene sulfonate (PSS))) (Li:PSS) polyelectrolyte as an HTL in inverted PSCs, where Li⁺ can act as a counter ion for the PSS backbone. The negative charge on the PSS backbone can stabilize the presence of p-type carriers and p-doping at the anode. Simple Li:PSS performed poorly due to poor surface coverage and voids existence in perovskite film as well as low conductivity. PEDOT:PSS was added to increase the conductivity to the simple Li:PSS solution before its use which also resulted in lower performance. Furthermore, a bilayer of PEDOT:PSS and Li:PSS was employed, which outperformed simple PEDOT:PSS due to high quality of perovskite film with large grain size also the large electron injection barrier (ϕ_e) impeded back diffusion of electrons towards anode. As a consequence, devices employing PEDOT:PSS / Li:PSS bilayers gave the highest PCE of 18.64%.     

钙钛矿型太阳电池研究进展

自从2009年钙钛矿材料被应用到太阳电池领域,到现在仅6年的时间里,钙钛矿型太阳电池的光伏转换效率从约3%提高到20.1%,受到全球瞩目。 本文对近年来钙钛矿型太阳电池的发展进行了综述,介绍了钙钛矿吸光材料的性能及其制备,总结了钙钛矿型太阳电池器件结构及其内在机理,探讨了该类型电池待突破的方向和可能的解决途径,阐述了钙钛矿型太阳电池的进展历程,展望了未来发展方向。     

Dimethylammonium Cation-Induced 1D/3D Heterostructure for Efficient and Stable Perovskite Solar Cells

Mixed-dimensional perovskite engineering has been demonstrated as a simple and useful approach to achieving highly efficient and more-durable perovskite solar cells (PSCs), which have attracted increasing research interests worldwide. In this work, 1D/3D mixed-dimensional perovskite has been successfully obtained by introducing DMAI via a two-step deposition method. The additive DMA⁺ can facilitate the crystalline growth and form 1D DMAPbI₃ at grain boundaries of 3D perovskite, leading to improved morphology, longer charge carrier lifetime, and remarkably reduced bulk trap density for perovskite films. Meanwhile, the presence of low-dimension perovskite is able to prevent the intrusion of moisture, resulting in enhanced long-term stability. As a result, the PSCs incorporated with 1D DMAPbI₃ exhibited a first-class power conversion efficiency (PCE) of 21.43% and maintained 85% of their initial efficiency after storage under ambient conditions with ~45% RH for 1000 h.     

SnO2双层电子传输层对钙钛矿太阳能电池界面电荷传输的影响

为了改善基于SnO₂电子传输层的钙钛矿太阳能电池的界面电荷传输特性和迟滞现象,我们采用低温溶液处理工艺制备了4种不同类型的SnO₂电子传输层用于钙钛矿太阳能电池,包括由SnCl₄·5H₂O溶胶-凝胶层(Cl₄-SnO₂)、SnCl₂·2H₂O溶胶-凝胶层(Cl₂-SnO₂)和SnO₂纳米颗粒层(NP-SnO₂)与SnO₂胶体层(Col-SnO₂)两两相互作用形成的同质结SnO₂双层电子传输层和Col-SnO₂单层电子传输层;并系统研究了不同SnO₂双层电子传输层对器件光电性能和迟滞现象的影响。通过扫描电镜(SEM)、X射线衍射(XRD)、稳态光致发光(PL)、电化学阻抗(EIS)和稳定性测试等表征证实,在Col-SnO...     

Composite Electrode SnO2／TiO2 for Dye-Sensitized Solar Cells

Composite nanoporous electrode SnO2/TiO2 was fabricated for the dye sensitized solar cell (DSSC) with N3 (Cis-Ru). After introducing of TiO2, the open-circuit photovoltage (Voc) was higher than that of the pure SnO2 electrode, while short-circuit photocurrent (Isc) was varied with the ratio of the TiO2. Appropriate content of the TiO2 can be beneficial to the efficiency of the solar cell, and it gives negative impact on the composite electrode when the content of TiO2 is higher.     

Mixed-phase Mesoporous TiO2 Film for High Efficiency Perovskite Solar Cells

Mesoporous scaffold structures have played great roles in halide perovskite solar cells(PSCs),due to the excellent photovoltaic performance and commercial perspective of mesoporous PSCs.Here,we reported a mixed-phase TiO2 mesoporous film as an efficient electron transport layer(ETL)for mesoporous perovskite solar cells.Due to the improved crystal phase,fihn thickness and nanopartMe size of TiO2 layer,which were controlled by varying the one-step hydrothermal reaction time and annealing time,the PSCs exhibited an outstanding short circuit photocurrent density of 25.27 mA/cm^2,and a maximum power conversion efficiency(PCE)of 19.87%.It is found that the ultra-high Jsc attributes to the excellent film quality,light capturing and excellent electron transport ability of mixed-phase TiO2 mesoporous film.The results indicate that mix-phase mesoporous metal oxide fihns could be a promising candidate for producing effective ETLs and high efficiency PSCs.     

A Modified Sequential Deposition Route for High-Performance Carbon-Based Perovskite Solar Cells under Atmosphere Condition

Carbon-based hole transport material (HTM)-free perovskite solar cells have exhibited a promising commercialization prospect, attributed to their outstanding stability and low manufacturing cost. However, the serious charge recombination at the interface of the carbon counter electrode and titanium dioxide (TiO₂) suppresses the improvement in the carbon-based perovskite solar cells’ performance. Here, we propose a modified sequential deposition process in air, which introduces a mixed solvent to improve the morphology of lead iodide (PbI₂) film. Combined with ethanol treatment, the preferred crystallization orientation of the PbI₂ film is generated. This new deposition strategy can prepare a thick and compact methylammonium lead halide (MAPbI₃) film under high-humidity conditions, which acts as a natural active layer that separates the carbon counter electrode and TiO₂. Meanwhile, the modified sequential deposition method provides a simple way to facilitate the conversion of the ultrathick PbI₂ capping layer to MAPbI₃, as the light absorption layer. By adjusting the thickness of the MAPbI₃ capping layer, we achieved a power conversation efficiency (PCE) of 12.5% for the carbon-based perovskite solar cells.