Revision of ISO guide 25

 ISO/IEC guide 25 is the internationally recognised base document for the accreditation of laboratories. Laboratory accreditation is a system of peer assessment and a formal recognition that a laboratory is competent to perform specific tests or types of tests ISO/IEC guide 25 plays a fundamental role in the life of the analytical chemist and is pivotal to the acceptance of the philosophy "once tested everywhere accepted" and to ensuring the mutual acceptance of test data. Within the EU, the attainment of accreditation to ISO/IEC guide 25 has become a way of life and it is now mandatory for laboratories engaged in certain regulatory work areas. Guide 25 is currently under revision and over the past 2 years or so it has been the subject of much debate among the calibration and testing community and it has engendered a considerable amount of written and oral comments. The latest revision entitled "Draft International Standard ISO/IEC DIS 17025: General Requirements for the Competence of Testing and Calibration Laboratories" was circulated to national standard organisations for their "comment and approval" in mid 1998. Voting on this document commenced on 9 July and terminates on 9 December 1998. It is anticipated that a final draft could be circulated in 1999. In accordance with the Vienna agreement this is a parallel ISO/CEN enquiry. This paper will discuss the implications of the technical requirements of the current document for analytical chemistry with particular emphasis on, the strengths, weaknesses and deficits inherent in the draft circulated in July 1998.     

抑制型电导检测离子色谱法测定饮用水中的痕量溴酸盐

建立一种直接进样测定饮用水中痕量溴酸盐的电导检测离子色谱法。选用Metrosep A Supp 5阴离子交换分离柱,碳酸盐淋洗液。抑制型电导检测采用化学抑制器和CO2抑制器顺序双抑制系统。实验结果显示,溴酸根阴离子与常见共存阴离子完全分离,溴酸盐含量在5~100 μg/L范围内具有良好的线性(r=0.9999),精密度高(相对标准偏差（RSD）<4%),方法的检出限为0.50 μg/L,样品加标平均回收率为96.1%~107%。该方法操作简单,分离效果好,可与常见阴离子实现同时分析,灵敏度高,重现性好,可作为饮用水中溴酸盐的标准测定方法。     

Determination of vitamin B12 in infant formula and adult nutritionals by HPLC: First Action 2011.10

During the "Standards Development and International Harmonization: AOAC INTERNATIONAL Mid-Year Meeting" held on June 29, 2011, an Expert Review Panel (ERP) reviewed the method "Determination of Vitamin B12 in Infant Formula and Adult Nutritionals by HPLC." Under the new pathway to Official Methods, the ERP adopted the method as Official First Action. The method is applicable to the determination of vitamin B12 in infant formula and adult nutritionals. Data showed an average overall intermediate precision of 6.64% RSD, an estimated quantitation limit of 0.8 microg/kg, and a detection limit of 0.2 microg/kg in prepared samples. The standard range of the method is 2 to 200 microg/L, which corresponds to an analytical range of 0.8 to 500 microg/kg.     

Determination of bromate in drinking water by ultraperformance liquid chromatography-tandem mass spectrometry

Bromate is a byproduct formed as a result of disinfection of bromide-containing source water with ozone or hypochlorite. The International Agency for Research on Cancer has recognized bromate as a possible human carcinogen, thus it is essential to determine in drinking water. Present work highlights a development of sensitive and fast analytical method for bromate determination in drinking water by using ultraperformance liquid chromatography-tandem mass spectrometry. The quality parameters of the developed method were established, obtaining very low limit of detection (0.01 ng/mL), repeatability and reproducibility have been found to be less than 3% in terms of relative standard deviation when analyzing a bromate standard at 0.05 μg/mL with 0.4 min analysis time. Developed method was applied for the analysis of metropolitan and bottled water from Saudi Arabia; 22 samples have been analyzed. Bromate was detected in the metropolitan water samples (from desalinization source) at concentrations ranging between 3.43 and 75.04 ng/mL and in the bottled water samples at concentrations ranging between 2.07 and 21.90 ng/mL. Moreover, in comparison to established analytical methods such as liquid chromatography-tandem mass spectrometry, the proposed method was found to be very sensitive, selective and rapid for the routine analysis of bromate at low level in drinking water.     

Validation of analytical methods used for determination of nitrate in soil

The standard method (ISO/DIS 14255) and the quick test were used for determination of nitrate in soil. We validated both methods using parameters such as accuracy, reproducibility within 1 day and between days, limit of detection and limit of quantification. The accuracy of the results was determined using the analysis of samples from the international interlaboratory scheme WEPAL. The accuracy of the standard method was good, while for the quick test the results were not accurate. The standard method showed a solid reproducibility of measurement results (in 1 day, relative standard deviation, RSD=0.2%; between days, RSD=0.8%). The quick test gave poorer results (in 1 day, RSD=6%; between days, RSD=7%). We tried to established the compatibility of both methods on real soil samples and we were satisfied to obtain the correlation coefficient 0.98 using the regression straight line. The analyses with the quick field instrument are much simpler and cheaper than the standard laboratory analyses and can be used for advising on nitrogen fertilisation.     

Kinetic spectrophotometric determination of low levels of nitrite by catalytic reaction between pyrogallol red and bromate

A kinetic spectrophotometric method for the determination of trace nitrite (0.003-1.000 microg/ml) based on its catalytic effect on the reaction between potassium bromate and pyrogallol red in acidic media is described. The reaction is monitored spectrophotometrically by measuring the decreasing colour of pyrogallol red at 467 nm by the fixed-time method. At a given time of 3.0 min at 30 degrees, the detection limit is 0.001 microg/ml and the relative standard deviation for 0.010 microg/ml nitrite is 1.8% (n = 8). The method is free from most interferences, especially from large amounts of nitrate and ammonium. The procedure was successfully applied to the determination of trace nitrite in natural water without preconcentration.     

Determination of low-level residual ethylene oxide by using solid-phase microextraction and gas chromatography

Current methods of analysis for ethylene oxide (EO) in medical devices include headspace and simulated-use extractions followed by gas chromatography with either a packed or a capillary column. The quantitation limits are about 0.5-1.0 microg/g for a packed column and about 0.1-0.2 microg/g for a capillary column. The current allowable levels of EO on medical devices sterilized with EO gas as outlined in International Organization for Standardization (ISO) 10993-7 may be significantly reduced from current levels by applying the ISO Draft International Standard 10993-17 method for establishing allowable limits. This may require EO test methods with detection and quantitation limits that are much lower than those of the currently available methods. This paper describes a new method that was developed for the determination of low-level EO by solid-phase microextraction using the direct-immersion method. Factors such as temperature and stirring were found to affect absorption efficiency and absorption time. A low extraction temperature (about 6 degrees C) was found to be more efficient than room-temperature extraction. Stirring was found to reduce absorption time by about 50%. Under these conditions, detection and quantitation limits of 0.002 and 0.009 microg/g, respectively, were obtained by using a capillary column. As a result, this method makes compliance with lower EO limits feasible.     

柱后衍生离子色谱法同时测定瓶装水中的碘酸根、亚氯酸根和溴酸根

水中的碘酸根、亚氯酸根和溴酸根是重要的消毒副产物,主要通过大体积浓缩后直接电导检测,或通过柱前或柱后化学反应将目标物转化成容易检测的物质后检测。本方法采用大体积进样柱后衍生紫外检测的分析方法,通过条件优化获得了较高的灵敏度和信噪比。利用一套自动分析系统,可以满足饮用水中痕量碘酸根、亚氯酸根、溴酸根的同时监测。碘酸根、亚氯酸根和溴酸根的检出限分别为0.5,0.4,0.1 μg/L。对于不同的加标样品,碘酸根、亚氯酸根和溴酸根的回收率分别为70.8%~98.0%,92.4%~100%和93.2%~104.1%。该方法应用于北京市场上的瓶装饮用水分析,结果显示瓶装纯净水中的碘酸根、亚氯酸根、溴酸根浓度均低于检出限,而瓶装矿泉水中碘酸根、溴酸根的最高含量分别达到9.4 μg/L和78.4 μg/L。     

Validation interlaboratory trial for ISO 12010: Water quality—Determination of short-chain polychlorinated alkanes (SCCP) in water

A validation interlaboratory trial was carried out to prepare ISO 12010: Water quality??Determination of short-chain polychlorinated alkanes (SCCP) in water??Method using gas chromatography/mass spectrometry (GC-MS) and electron capture negative ionisation (ECNI). The task was to determine the sum of short-chain polychlorinated n-alkanes with carbon chain lengths of C₁₀?CC₁₃ and a chlorine content between 49% (g/100?g) and 67% (g/100?g) in water by GC-ECNI-MS. The quantification had to be performed by multiple linear regression as described in ISO/DIS 12010, the compulsory method. Samples distributed were real river samples, and waste water spiked with a target concentration of 0.4 and 0.6???g/L for the sum of SCCPs, i.e. a concentration around the environmental quality target level according to the European Water Framework Directive. The different types of water samples tested were surface water with <150?mg/L suspended matter, surface water with 0.5?g/L suspended matter, and filtered waste waster. The interlaboratory trial included the extraction of the water samples, a column chromatographic clean up, a concentration step, and integration of chromatographic unresolved complex mixtures as well as the calibration and quantification by multiple linear regression. The reproducibility standard deviation of the standard concentration was 11.9%. Reproducibility standard deviations of concentrations in the three different water samples between 27.8 and 34.2% were achieved by 10?C12 participating laboratories from six countries.     

Method validation for determination of the 15 European-priority polycyclic aromatic hydrocarbons in primary smoke condensates by gas chromatography/mass spectrometry: interlaboratory study

A collaborative study was conducted to validate an analytical method for quantification of the 15 polycyclic aromatic hydrocarbons (PAHs) regarded in 2002 as a health concern by the former Scientific Committee on Food of the European Commission (SCF) in primary smoke condensates. The method is based on gas chromatography/mass spectrometry of a cyclohexane extract with solid-phase cleanup through silica gel. The analytes were detected in the selected-ion monitoring mode and quantified by using 3 isotopically labeled internal standard compounds. Seventeen laboratories participated in the collaborative validation study, of which 12 reported valid results. The data were subjected to Cochran, single Grubbs, and double Grubbs tests for statistical outliers. A maximum of 2 outliers was eliminated before further statistical evaluation of the method performance characteristics. Depending on the analyte, the results showed relative standard deviations for repeatability between 4.2 and 30% and for reproducibility from 9.9 to 60%. The recoveries varied between about 50 and 85%, except those for cyclopenta[cd]pyrene, dibenzo[a,l]pyrene, and dibenzo[a,h]pyrene. Nevertheless, because Commission Directive 2005/10/EC allows for a recovery range of 50-120% for (BaP) benzo[a]pyrene in various foods, it can be concluded that the method performs appropriately within the analytical range between 5 and 25 microg/kg of primary smoke condensate. For BaP the validated analytical range covered 5-20 microg/kg, and for benzo[a]anthracene (BaA) 10-25 microg/kg. The method is suitable for monitoring BaP and BaA at their respective maximum permitted levels of 10 and 20 microg/kg. Three analytes, benzo[b]-, benzo[j]-, and benzo[k]-fluoranthene could not be separated by all of the participants and were therefore treated as the sum. Nevertheless, with this method the pattern of the respective concentrations of these 15 PAHs can be monitored in primary smoke condensate as suggested by the SCF.     

Chloride interference in the determination of bromate in drinking water by reagent free ion chromatography with mass spectrometry detection

Bromate, a well known by-product of the ozonation of drinking water, has been included among the substances which have to be monitored in the drinking water according to the last EC Directive 251/98 on potable water with a regulated limit of 10 microg l(-1). The need of performing routine analysis at this limit is a driving force for the developing of new simple and sensitive methods of detection, which should be also able to overcome the effect of matrix composition. This work explored the use of mass spectrometry detection with electrospray ionisation hyphenated to a reagent free ion chromatograph with hydroxide gradient elution for the determination of bromate in drinking water. The use of a high capacity hydroxide selective column operated in gradient mode allowed to avoid the interference by carbonate peak, which moved to longer retention times. The effect of increasing chloride concentrations from 0 to 250 mg l(-1), which is the guideline limit for drinking water in Directive 251/98/EC, was to decrease absolute mass spectrometric response and chromatographic efficiency and, on the consequence, to increase the effective detection limits. The effect of the chloride concentration on the detection of bromate is discussed.     

A simple diffuse reflectance Fourier transform infrared spectroscopic determination of sulfur dioxide in ambient air using potassium tetrachloromercurate as the absorbing reagent

This paper presents development of a simple, rapid, and precise analytical method for determination of sulfur dioxide in ambient air by a gas to solid-phase conversion method. Sulfur dioxide is determined in the form of sulfite (SO3(2-)) because the absorbing reagent, potassium tetrachloromercurate (TCM), used in this method absorbs sulfur dioxide from the atmosphere in the form of sulfite. Determination of submicrogram levels of sulfur dioxide was based on the selection of a quantitative analytical peak at 495 cm(-1) among the 3 observed vibrational peaks for the dichlorosulfitomercurate complex formed after reaction of sulfur dioxide with TCM and measurement of absorbance using diffuse reflectance Fourier transform infrared spectroscopy. The limits of detection and quantification of the method were found to be 0.09 and 0.4 microg/g SO3(2-), respectively. The precision in terms of standard deviation and relative standard deviation (RSD) at a level of 2 microg SO3(2-)/10.1 g KBr for n = 10 was found to be 0.036 microg SO3(2-) and 1.8%, respectively. The RSD (n = 10) for determination of sulfur dioxide in ambient air was observed to be in the range of 2.7-4.2%. The method proposed is time saving and eliminates the slow and cumbersome steps of pH maintenance of the reaction mixture and color formation of the U.S. Environmental Protection Agency recommended West and Gaeke spectrophotometric method and other methods for quantitative determination of sulfur dioxide.     

Analysis of bromate in drinking water using liquid chromatography-tandem mass spectrometry without sample pretreatment

An analytical method for determining bromate in drinking water was developed using liquid chromatography-tandem mass spectrometry (LC-MS/MS). The (18)O-enriched bromate was used as an internal standard. The limit of quantification (LOQ) of bromate was 0.2 μg/L. The peak of bromate was separated from those of coexisting ions (i.e., chloride, nitrate and sulfate). The relative and absolute recoveries of bromate in two drinking water samples and in a synthesized ion solution (100 mg/L chloride, 10 mg N/L nitrate, and 100 mg/L sulfate) were 99-105 and 94-105%, respectively. Bromate concentrations in 11 drinking water samples determined by LC-MS/MS were <0.2-2.3 μg/L. The results of the present study indicated that the proposed method was suitable for determining bromate concentrations in drinking water without sample pretreatment.     

Determination of trace concentrations of bromate in municipal and bottled drinking waters using a hydroxide-selective column with ion chromatography

The International Agency for Research on Cancer determined that bromate is a potential human carcinogen, even at low micro/l levels in drinking water. Bromate is commonly produced from the ozonation of source water containing naturally occurring bromide. Traditionally, trace concentrations of bromate and other oxyhalides in environmental waters have been determined by anion exchange chromatography with an IonPac AS9-HC column using a carbonate eluent and suppressed conductivity detection, as described in EPA Method 300.1 B. However, a hydroxide eluent has lower suppressed background conductivity and lower noise compared to a carbonate eluent and this can reduce the detection limit and practical quantitation limit for bromate. In this paper, we examine the effect of using an electrolytically generated hydroxide eluent combined with a novel hydroxide-selective anion exchange column for the determination of disinfection byproduct anions and bromide in municipal and bottled drinking water samples. EPA Methods 300.1 B and 317.0 were used as test criteria to evaluate the new anion exchange column. The combination of a hydroxide eluent with a high capacity hydroxide-selective column allowed sub-microg/l detection limits for chlorite, bromate, chlorate, and bromide with a practical quantitation limit of 1 microg/l bromate using suppressed conductivity detection and 0.5 microg/l using postcolumn addition of o-dianisidine followed by visible detection. The linearity, method detection limits, robustness, and accuracy of the methods for spiked municipal and bottled water samples will be discussed.     

气相色谱-质谱法测定动物组织中三种1,2-二苯乙烯类药物的残留量

建立了动物组织中己烯雌酚(DES)、己二烯雌酚(DIS)和己烷雌酚(HS)残留量的气相色谱-质谱分析方法。动物组织样品在碱性条件下用乙酸乙酯提取,经碳酸钠溶液液-液分配净化,再用硅胶柱固相萃取净化,洗脱液均分成两份后经氮气吹干,分别用双三甲基硅基三氟乙酰氨(BSTFA)和七氟丁酸酐(HFBA)衍生,采用选择离子监测模式(SIM)进行测定,外标法定量。检出限为0.30 μg/kg(cis-DES),0.10 μg/kg(trans-DES和HS)和0.15 μg/kg(DIS)。在0.5~4.0 μg/kg添加水平,回收率为73.0%～86.5%,相对标准偏差(RSD)为1.0%～7.2%。衍生物的峰面积与样品浓度在10～1000 μg/L(DES和DIS) 和5～500 μg/L(HS)范围内呈良好的线性关系,线性回归系数大于0.99。     

Comparison of on-line coupling of ion-chromatography with atmospheric pressure ionization mass spectrometry and with inductively coupled plasma mass spectrometry as tools for the ultra-trace analysis of bromate in surface water samples

Ion chromatography in combination with atmospheric pressure ionization mass spectrometry (API-MS) as well as with inductively coupled plasma mass spectrometry (ICP-MS) had been compared for trace analysis of bromate. The results indicate that both techniques yield comparable results, which are in excellent agreement with standard methods for bromate determination. Furthermore, both techniques showed almost equal absolute detection limits (approximately 50 pg bromate injected). Contrary to IC-API-MS, IC-ICP-MS can tolerate a higher salt concentration in the mobile phase. This allows the use of high-capacity columns combined with large sample volumes. This lowered the concentration based detection limits by one order of magnitude for IC-ICP-MS compared to IC-API-MS (0.06 microg/l vs. 0.5 microg/l). On the other hand, IC-API-MS is able to allow a positive identification of bromate even in cases when IC does not fully separate bromate from other bromine-containing species. The performance data of both IC-MS techniques have been established by participation in an international round robin test.     

Determination of trace level bromate and perchlorate in drinking water by ion chromatography with an evaporative preconcentration technique

A simple sample preconcentration technique employing microwave-based evaporation for the determination of trace level bromate and perchlorate in drinking water with ion chromatography is presented. With a hydrophilic anion-exchange column and a sodium hydroxide eluent in linear gradient, bromate and perchlorate can be determined in one injection within 35 min. Prior to ion chromatographic analysis, the drinking water sample was treated with an OnGuard-Ag cartridge to remove the superfluous chloride and concentrated 20-fold using a PTFE beaker in a domestic microwave oven for 15 min.The recoveries of the anions ranged from 94.6% for NO2- to 105.2% for F-. The detection limits for bromate, perchlorate, iodate and chlorate were 0.1, 0.2, 0.1 and 0.2 microg/l, respectively. The developed method is applicable for the quantitation of bromate and perchlorate in drinking water samples.     

Adsorptive voltammetric determination of copper as its nioximate complex

A sensitive and selective stripping voltammetric ultratrace determination of copper is described, based on adsorptive accumulation of the cu(II)-nioxime complex on the surface of a hanging mercury drop electrode, followed by the reduction of the adsorbed complex during the cathodic scan. The analytical conditions for the determination of copper by differential-pulse and linear-scan absorption voltammetry have been optimized. The method is compared to the routine anodic stripping voltammetric method for copper. Its applicability to river and potable water analysis is illustrated. The detection limit, restricted by the blank, is about 0.5 microg/l.; the relative standard deviation (at microg/l. level) for a standard solution is below 5% and for water samples is 5-9%.     

Ion chromatographic determination of trace iodate, chlorite, chlorate, bromide, bromate and nitrite in drinking water using suppressed conductivity detection and visible detection

An ion chromatography method for the simultaneous determination of trace iodate, chlorite, chlorate, bromide, bromate and nitrite in drinking water has been developed using an anion-exchange column and the suppressed conductivity detector, followed by post-column addition of reagent to enhance visible absorbance detection of ions. A high capacity anion exchange Ion Pac9-HC column (250 mm x 4 mm I.D.) was used. Eight millimole per liter sodium carbonate was used as eluent, an auto-suppression external water mode was selected, 0.5 g/l o-dianisidine.2HCl (ODA)+4.5 g/l KBr+25% methanel+5.6% nitric acid was used as post-column reagent. The post-column reaction (PCR) temperature was at 60 degrees C, and the visible absorbance detected wavelength at 450 nm. The sample's pH and coexist anions had no influence on determination. The method enjoyed a wide linear range and a good linear correlation coefficient (r>0.999). The method detection limits were between 0.023 and 2.0 microg/l. The average recoveries ranged from 87.5 to 110.0%, and the relative standard deviations (RSD) were in the range of 1.1-4.6%. The analytical results by the method of post-column addition of reagent to enhance visible absorbance detection of anions was compared with that of the suppressed conductivity detection, and the former was proved to be better in sensitivity and selectivity. The results showed that this method was accurate, sensitive and might be good for application and suitable for trace analysis at the level of mug/l.     

Application of single-drop microextraction and comparison with solid-phase microextraction and solid-phase extraction for the determination of alpha- and beta-endosulfan in water samples by gas chromatography-electron-capture detection

Water contamination due to the wide variety of pesticides used in agriculture practices is a global environmental pollution problem. The 98/83 European Directive requires the measurement of pesticides residues at a target concentration of 1.0 microg/l in surface water and 0.1 microg/l in drinking water. In order to reach the level of detection required, efficient extraction techniques are necessary. The application of a new extraction technique: single-drop microextraction (SDME), followed by gas chromatography with electron-capture detection, was assessed for determining alpha-endosulfan and beta-endosulfan in water samples. Experimental parameters which control the performance of SDME, such as selection of microextraction solvent and internal standard, optimization of organic drop volume, effects of sample stirring, temperature and salt addition, and sorption time profiles were studied. Once SDME was optimized, analytical parameters such as linearity, precision, detection and quantitation limits, plus matrix effects were evaluated. The SDME method was compared with solid-phase microextraction and solid-phase extraction with the aim of selecting the most appropriate method for a certain application.