酚醛型吸附树脂对咖啡因和茶碱吸附性能的研究

用静态和动态方法研究了酚醛型吸附树脂JDW-2和DuoliteS-761对咖啡因和茶碱的吸附行为.结果表明,自制树脂JDW-2对咖啡因和茶碱的吸附性能明显优于DuoliteS-761.树脂的比表面积、含水量、酚羟基的含量与吸附关系密切,尽管JDW-2的比表面积比DuoliteS-761小,但前者比后者具有更高的含水量(42%)和酚羟基含量(3.72mmol/g).在静态条件下,JDW-2吸附咖啡因的速率比DuoliteS-761快,JDW-2树脂对咖啡因和茶碱饱和吸附量分别为246和127mg/g干树脂,而DuoliteS-761树脂对它们的吸附量分别为121和53mg/g干树脂;JDW-2和DuoliteS-761吸附咖啡因的初始阶段是粒扩散控制过程;酚醛型吸附树脂等温吸附咖啡因和茶碱的平衡吸附数据符合Langmuir方程.酚醛型吸附树脂吸附咖啡因和茶碱属单分子层吸附.在动态条件下,1mol/LHCl和40%甲醇溶液以1.5BV/h来洗脱吸附咖啡因的JDW-2,在4～5个床体积的洗脱率分别是88%和93%,而1mol/LHCl和80%甲醇溶液以1.5BV/h来洗脱吸附茶碱的JDW-2,在3～4个床体积的洗脱率分别是91%和96%,表明酚醛型吸附树脂具有良好的洗脱性能,用1mol/LHCl和40%(或80%)甲醇溶液作复合洗脱剂从JDW-2中洗脱咖啡因(或茶碱),效     

离子交换法去除有机二胺吸收剂PA-A中SO42-的工艺研究

采用单因素实验法,考察了3种树脂对有机二胺吸收剂PA-A水溶液中SO42-的动态吸附-解吸性能,优化了树脂动态吸附-再生工艺.结果表明,D296型树脂具有良好的吸附选择性和较高的吸附容量;当流速为8.08BV/h、高径比为5.64、初始SO42-浓度为96.94g/L时,D296型树脂对PA-A水溶液中的SO42-动态饱和吸附量可达430.06mg/g干树脂;采用4％ NaOH水溶液在4.04BV/h的流速下对吸附饱和的树脂进行洗脱,再生率可达95％左右;树脂重复使用10次后其吸附-解吸性能基本不变.     

717型阴离子交换树脂吸附水溶性芳香族有机污染物研究

研究了717型阴离子交换树脂对苯酚、苯甲酸和十二烷基苯磺酸钠(SDBS)等水溶性芳香族污染物吸附过程的基本化学问题.研究结果表明:717型树脂对苯酚、苯甲酸和SDBS的吸附过程均符合Lagergren二级吸附动力学方程,吸附速率均随着温度的升高而加快,吸附表观活化能Ea分别为13.2kJ/mol、59.5kJ/mol和48.1kJ/mol,吸附过程△H0和△S0均为正值,△G0均为负值,吸附能够自发进行;吸附等温模型符合Langmuir等温式;318K时,717型树脂在pH=9.1对SDBS的饱和吸附容量为360mg/g;在pH=10.2,对苯酚和苯甲酸的饱和吸附容量分别为194mg/g和286mg/g.用浓度均为0.5mol/L,体积比为5∶1的NaCl-NaOH混合溶液可快速洗脱树脂上吸附的污染物,洗脱率达98％以上.该树脂对水溶性芳香族污染物吸附容量大,易于再生和循环利用,可用于环境水体中水溶性芳香族有机污染物的吸附治理.     

氨基膦酸螯合树脂吸附重稀土的研究

研究了重稀土在氨基膦酸树脂的吸附行为.试验结果表明,氨基膦酸树脂对重稀土的吸附在pH=5.0的HAc-NaAc缓冲溶液时最佳;298K时静态饱和吸附容量为332mg/g干树脂;用2mol/L盐酸洗脱,洗脱率为91.2%;等温吸附服从Freundlich经验式;吸附反应中△H=10.76kJ/mol,表观速率常数k298=1.223×10-4s-1,表观活化能Ea=3.2kJ/mol.     

大孔吸附树脂纯化迷迭香脂溶性总酚酸的研究

从X-5、D4020、AB-8、H1020、NKA-Ⅱ、HPD-100A、SIPI、HPD800和D3520大孔吸附树脂中筛选出H1020树脂,研究了其对迷迭香脂溶性总酚酸的静态与动态吸附和解吸性能.结果表明,H1020树脂对迷迭香脂溶性总酚酸的饱和吸附量为19.84mg/g干树脂,饱和吸附时间为3h,适宜的解吸荆为体积分数90%的乙醇溶液;以质量浓度为4.45m/mL的迷迭香提取液上柱,流速为1.0mL/min,当吸附平衡后,2.7BV体积分数90%的乙醇溶液可将吸附的总酚酸完全洗脱.经动态纯化后,脂溶性总酚酸质量分数从47.74%提高到70.46%,该组分清除DPPH自由基的IC50值为0.0469mg/mL.     

羧甲基壳聚糖微球对活性艳红X-3B的吸附行为研究

用交联的壳聚糖微球(CTS)与氯乙酸在碱性条件下反应,合成了羧甲基壳聚糖树脂(CMCT)。其吸附染料活性艳红X-3B的实验结果表明,CMCT和CTS均对偶氮染料活性艳红X-3B有较好的去除能力。实验条件下,最大平衡吸附量分别为611.5mg/g和365.2mg/g,说明羧甲基的引入提高了壳聚糖的吸附能力。等温吸附可以用Langmuir方程较好的描述,表明为单分子层吸附。动力学过程用二级吸附动力学模拟具有很好的线性相关性,通过二级吸附模型计算出的平衡吸附量与实验值相符。流动床实验表明,CMCT和CTS对浓度为100mg/L的X-3B溶液吸附的穿透点分别为6000ml/g和3375ml/g,用0.1mol/L的氢氧化钠溶液洗脱,洗脱峰集中,洗脱率都在90%以上。洗脱再生后的CMCT和CTS树脂均可重复使用。     

N263浸渍树脂吸附分离In(Ⅲ)、Fe(Ⅲ)的初步研究

以HZ-818大孔吸附树脂为载体,甲基三辛基氯化铵(N263)为萃取剂,利用干浸渍方法制备了N263浸渍树脂。采用静态吸附法考察了在盐酸体系中盐酸浓度、金属离子浓度、温度以及时间等因素对制备的浸渍树脂吸附分离In3+、Fe3+性能的影响。结果表明,浸渍树脂吸附In3+、Fe3+的最佳盐酸浓度均为4mol/L;其吸附In3+、Fe3+的等温吸附曲线符合Langmuir等温吸附模型;298K下对Fe3+、In3+的饱和吸附容量分别为43.42mg/g、14.53mg/g。动力学研究表明,298K下浸渍树脂吸附Fe3+、In3+的平衡时间分别为6h、10h。准二级动力学方程可较好地描述浸渍树脂对In3+、Fe3+的吸附行为。混合体系中,浸渍树脂对Fe3+表现出较好的吸附性能,而对In3+基本上不吸附,从而达到了初步分离In3+、Fe3+的目的。     

大孔阳离子交换树脂对奈替米星的吸附研究

通过正交实验合成了9种大孔弱酸性阳离子交换树脂,筛选出具有最大动态饱和吸附量的FB-1树脂.采用红外光谱和热重分析的方法对其表征,并研究其对奈替米星的吸附及解吸性能,结果表明:该树脂对奈替米星的吸附符合Langrnuir吸附:用氨水做洗脱剂,0.3mol/L和0.4mol/L的氨水解吸率均达95%以上.FB-1与HD-2树脂比较:动态吸附量FB-1为398.0mg/mL湿树脂、HD-2为232.1mg/mL湿树脂;0.3mol/L氨水解吸,前者解吸率较后者高约15%.     

聚酰胺和负载聚酰胺树脂富集分离环境水中无机汞

提出以聚酰胺、负载双硫腙聚酰胺、负载α-巯基苯并噻唑聚酰胺树脂为吸附剂,在静态和动态条件下,对环境水中无机汞的选择性吸附分离方法.实验表明,此3种树脂在0.1～2.5mol/L HCI介质中,对无机汞吸附性能很好,饱和吸附容量分别为:聚酰胺树脂12.28mg/g;负载双硫腙聚酰胺树脂14.48mg/g;负载α-巯基苯并噻唑聚酰胺树脂17.17mg/g.吸附到各树脂中的汞可用1%～5%硫脲溶液解脱,以冷原子吸收法测定,得到较满意的结果.     

磁性PS-DEA树脂的制备与表征

利用二乙醇胺(DEA)对氯甲基化聚苯乙烯基树脂(PS-Cl)进行表面改性,制备了亲水性的PS-DEA树脂,然后以FeCl3·6H2O和FeSO4·7H2O为前驱体通过共沉淀法原位复合制备了磁性PS-DEA树脂.表征了磁性PS-DEA样品的形貌、结构以及磁性能,研究了PS-DEA和磁性PS-DEA对水溶液中Hg(Ⅱ)的吸附性能.结果表明,含有Fe3O4的磁性PS-DEA树脂的比饱和磁化强度(Ms)为0.92 A·m2/kg,磁性树脂中Fe3O4所占的质量分数为1.7%.用Langmuir等温模型拟合了PS-DEA和磁性PS-DEA对水溶液中Hg(Ⅱ)的吸附数据,计算得到最大吸附量分别为320.51和352.11 mg/g,这表明磁性纳米粒子的引入有利于提高树脂的吸附性能,这种磁性树脂有望作为吸附剂用于水处理领域.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.