Enhancements in dissociative electron attachment to CF4, chlorofluorocarbons and hydrochlorofluorocarbons adsorbed on H2O ice

We report that the absolute cross sections for dissociative attachment of approximately 0 eV electrons to chlorofluorocarbons (CFCs) and hydrochlorofluorocarbons (HCFCs) are strongly enhanced by the presence of H2O ice. The absolute cross sections for CFCl3, CHF2Cl, and CH3CF2Cl on water ice are measured to be approximately 8.9 x 10(-14), approximately 5.1 x 10(-15), and approximately 4.9 x 10(-15) cm2 at approximately 0 eV, respectively. The former value is about 1 order of magnitude higher than that in the gas phase, while the latter two are 3-4 orders higher. In contrast, the resonances at electron energies > or = 2.0 eV are strongly suppressed either for CFCs and HCFCs or for CF4 adsorbed on H2O ice. The cross-section enhancement is interpreted to be due to electron transfer from precursor states of the solvated electron in ice to an unfilled molecular orbital of CFCs or HCFCs followed by its dissociation. This study indicates that electron-induced dissociation is a significant process leading to CFC and HCFC fragmentation on ice surfaces.     

CFC phase-out: have we met the challenge?

In 1974 Nobel prize winners Rowland and Molina proposed that chlorofluorocarbons (CFCs) were stable enough to reach the stratosphere, where, under intense solar radiation they released Cl atoms that could destroy stratospheric ozone protecting the earth’s surface from UV rays. The CFC industry funded both scientific studies to test the Rowland and Molina hypothesis and programmes to identify potential replacements, from which the HFCs emerged as likely candidates. After 5 years it was concluded, on the best scientific evidence available, that stratospheric ozone was being depleted at ∼3% per decade, but sufficient time was available for an orderly phase-out. Although the USA and a few other countries stopped the use of CFCs in aerosols little further work was done until 1985 when the CFC debate was renewed following the discovery of stratospheric ozone depletion over the Antarctic during its spring. Manufacturers restarted their R&D programmes; governments negotiated the Montreal Protocol in 1987 agreeing the partial phase-out of the CFCs. As a result of subsequent amendments CFCs have now been phased-out in the developed world and HCFCs will follow over the next two decades. This paper reviews what has been achieved and what remains to be done. Has the world-wide effort been successful in protecting the ozone layer? Have “acceptable” alternatives been found for the CFCs/HCFCs in their various applications?     

CFC and Halon replacements in the environment

Substitute fluorocarbons may have direct environmental impact, for example as greenhouse gases, or indirect impacts through the products of their decomposition in the environment. The mechanisms of that atmospheric decomposition are reviewed here and shown to be well established now. The end products are halogen acids and trifluoroacetic acid, all of which pre-exist in the environment in quantities greater than are expected to arise from fluorocarbon use and emissions. Furthermore, the growth in use of fluorocarbon replacements has been shown to be far less than the fall in CFC and Halon production. Hydrochlorofluorocarbons (HCFCs) have replaced less than one third of CFCs and are, themselves, ozone depleting substances that will be phased out under the Montreal Protocol. The growth in hydrofluorocarbons (HFCs) amounts to about 10% of the fall in CFCs. It is likely that the impact of new fluorocarbons on climate change will be a very small fraction of the total impact, which comes mainly from the accumulation of carbon dioxide in the atmosphere.     

Fluorocarbons in the global environment: a review of the important interactions with atmospheric chemistry and physics

Fluorocarbon impact on ozone depletion is reviewed together with the efficacy of the Montreal Protocol in acting to correct the imbalance between stratospheric ozone production and destruction. The Protocol is also helping to reduce global warming: CFCs are shown to be currently the largest fluorocarbon contributors to climate change. Relative contributions to climate change from CFCs and their HFC substitutes are discussed, together with the consequences of control of minor greenhouse gases on an environmental impact which is dominated by carbon dioxide emissions. Both the potencies of the materials for environmental change and their concentrations in the atmosphere are important and are considered here.Trifluoroacetic acid, a minor product of atmospheric decomposition of some HCFCs and HFCs and of the pyrolysis of fluoropolymers, has been shown to be uniformly distributed in seawater to a depth of over 4000 m and so is natural, although the actual source has yet to be identified.The Montreal Protocol is only one example of action to reduce undesirable impact from fluorocarbons. Other, less universal, actions include abatement of fluoroform greenhouse gas emissions from HCFC manufacturing, process changes to eliminate trifluoromethylsulfur pentafluoride emissions from electrochemical fluorination and ceasing manufacture of perfluorooctanyl sulfonate compounds due to their persistence in human tissue.     

Analysis of anions in hydrofluoro ethers by ion chromatography

Hydrofluoro ethers (HFES) are considered to be an ideal cleaning solvent in applications like vapor degreasing and wet cleaning. It is also a good solvent replacement for CFCs (chlorofluorocarbons), HCFCs (hydrochlorofluorocarbons), HFCs (hydrofluorocarbons) and chlorinated solvents because they have a short atmospheric lifetime and low global warming potential. Based upon their properties, hydrofluoro ethers are ideally suited for the demands of the electronics industry. However, the electronics industry requires these solvents to have high purity, especially in the area of residual anions. This paper will present information on an extraction methodology for the transfer of anions from the hydrofluoro ether to water. Then, an analytical method utilizing ion chromatography that is capable of detection of 10 anions (fluoride, acetate, formate, chloride, nitrite, bromide, nitrate, sulfate, oxalate, and phosphate) in the part per billion level will be demonstrated.     

金催化制备氯乙烯单体进展

本文综述了Au用于乙炔氢氯化反应的研究历史、最新研究进展及商业化进程。讨论了使用不同前驱体和添加第二金属助剂等方法对催化剂性能的改进,探讨了活性金物种的性质。尽管HgCl2会导致环境污染等问题,但全球大量聚氯乙烯(PVC)的生产仍采用HgCl2作为催化剂。由于中国计划未来几年内将不再使用Hg生产PVC,因此急需探索替代催化剂。数十年来人们普遍认为Au是该过程的最佳替代催化剂,这主要是因为与其他金属相比,金催化剂的选择性更高。     

A theoretical analysis of the electret air-gap field-effect structure for sensor applications

In order to develop a capacitive solid state sensor that makes use of an electret, a theoretical analysis is given of an electret air-gap field-effect structure.This structure is basically an MOS transistor with a movable gate and can thus be considered as a pressure-sensitive field effect transistor.It is shown that the addition of a metal layer on top of the semiconductor-oxide increases the sensitivity due to charge density multiplication.All calculations are based upon the displacement sensitivity S, which is independent of the mechanical properties of the diaphragm and thus independent of a specific application.Based upon the calculated sensitivities of the several configuration, a well-considered decision can be made as to which configuration is best suited for a specific application. In this paper this has been done for a solid state microphone and a pressure sensor as examples.     

Focused ultrasound and molecularly imprinted polymers: a new approach to organotin analysis in environmental samples

There is a high interest in speciation of organotin compounds (OTCs) in biota and marine sediment samples, due to their influence in the transmission of the contamination in the trophic chain. Sample treatment is still the most "compromising" step of speciation analysis. Extraction methods are in general time-consuming due to long extraction times and several analytical steps involved. In addition, in most cases there are problems of low recovery, especially for MBT. These drawbacks, added to the high matrix effects generally present in biota samples, make the sample treatment for organotin analysis a serious challenge for environmental issues. Here we present a novel, fast and efficient two steps method for organotin speciation in mussel and oyster tissue as well as in marine sediments. The first step based on the use of ultrasonic probe extraction for species leaching allowed us to quantitatively extract these compounds in a few minutes. Matrix interferences drastically decreased by applying a clean-up step based on the use of an imprinted polymer especially designed for tributyltin (TBT). This procedure increased accuracy and precision of the GC-FPD analysis and improving the limit of detection, Besides, this new method prevents the use of standard addition calibration method, which is mandatory without the clean-up step. The optimization and validation has been performed by using three reference materials: mussel tissue CRM-477, oyster candidate T-38 and sediment PACS-2.     

High performance liquid chromatography and capillary electrophoresis in the analysis of soybean proteins and peptides in foodstuffs

The increasing interest in functional and healthy food products has promoted the use of soybean in the manufacture of foods for human consumption. Soybean basic products (soybeans, textured soybean, soybean flour, soybean protein concentrate and soybean protein isolate) as well as soybean derivatives (soybean dairy-like products, soybean drinks with fruits, meat analogues, etc.) are commercially available. In addition, due to the interesting nutritional and functional properties of soybean proteins, they are usually employed as ingredient in the elaboration of a large number of food products such as bakery or meat products among others. In spite of the good characteristics of soybean proteins, their addition to some products is forbidden or allowed up to a certain limit. Therefore, analytical methodologies to achieve the determination of soybean proteins in foods are necessary in order to make possible adequate quality control and to prove that legal regulations controlling their addition are accomplished. However, this is not an easy task due to the diversity and complexity of the food matrices and the technological treatments to which some of these foods are submitted during their elaboration. This article presents for the first time a comprehensive review on the analytical methodologies developed using HPLC and CE to characterize soybeans and to analyse soybean proteins in meals. Moreover, the use of HPLC and CE in the characterization of soybean protein fractions and their hydrolyzates, and a study of their relationships to nutritional, functional and biomedical properties are included. Finally, the application of proteomic methodologies in soybean food technology is also reviewed.     

Effect of epoxy and filler concentrations on curing behaviour of isotropic conductive adhesives

Isotropic conductive adhesives (ICAs) are considered as the most promising replacement to lead-based solders due to relatively low melting point, simple processing and fine pitch capability. The study reports on the effect of volume fractions of silver flakes and particles on the curing reaction of ICAs. In addition, the thermal behavior of ICAs formulated with two types of polymeric adhesives: diglycidylether of bisphenol-A (DGEBA) and polyurethane (PU) was also investigated in this work. The increase in silver flakes concentration seem to reduce the melting temperature of the DEGBA and PU-based ICAs, which could be due to retardation of cross-linking of polymers due to silver flakes acting as barrier within the polymer matrix. In addition, the formulation of ICAs containing silver flakes and particles yielded a much higher reaction compared to conventional ICAs. The study showed that use of polyurethane (PU) as opposed to conventional Diglycidylether of bisphenol-A (DGEBA) showed a more stable system.     

Fluorescent derivatization of nitrite ions with 2,3-diaminonaphthalene utilizing a pH gradient in a Y-shaped microchannel.

The on-chip derivatization of nitrite ions with 2,3-diaminonaphthalene (DAN) utilizing a pH gradient formed in a Y-shaped microchannel was investigated. Nitrite ions react with DAN at low pH, and strongly fluoresced at high pH. Therefore, a reaction at low pH followed by the addition of a strong alkaline solution is the usual procedure in a batch scheme. However, a strong alkaline solution, like an NaOH aqueous solution, erodes the wall of the microchannels in substrates made of glass or polymers, and has not been considered suitable for use in microchannels. We first investigated the derivatization reaction and fluorescent properties of nitrite ions with DAN. We found that the on-chip fluorescent derivatization reaction and detection without the addition of an alkaline solution is possible by controlling the pH values of the nitrite solution and the DAN solution to form a suitable pH gradient by utilizing a buffering effect of triethanolamine solution, which is used as an NO2 gas-absorption medium. These results have suggested the feasibility of novel reaction schemes which can provide the desired products due to a controlled pH gradient in the microchannels, as well as the possibility of an on-site monitoring microchip device for ambient NO2.     

Addition of alkynes to aldehydes and activated ketones catalyzed by rhodium-phosphine complexes

A mixture of 2-(di-tert-butylphosphino)biphenyl and dicarbonylacetonato rhodium(I) provides an effective catalyst system for the addition of alkynes to aldehydes and activated ketones. In contrast to the more common zinc-catalyzed processes, enolizable 1,2-dicarbonyls are excellent substrates for these rhodium-catalyzed additions. This reaction allows for the formation of propargylic alcohols under mild conditions, tolerating many functional groups (such as carboxylic acids) that are incompatible with other methods. Little selectivity was observed in cases of unsymmetrical 1,2-diketones. Addition of alkynes to aldehydes with an adjacent chirality center usually provides the Felkin addition product with excellent selectivity in some cases. Studies on the catalyst structure show that both the beta-diketonate and a carbon monoxide ligand appear to be bound to the active catalyst. The use of chiral phosphines to induce asymmetry in the propargyl alcohol products provided low enantioselectivity, which may be due to the phosphine having a distal relationship to the reacting centers. Modification of other ligands, such as the beta-diketonate, appears to be a more promising avenue for the development of an enantioselective variant.     

Highly sensitive indirect photometric detection of cations by capillary electrophoresis with the cationic dye chrysoidine

The cationic dye, chrysoidine, has been used for the first time as a probe for the indirect photometric detection of cations. The dye has been used as a probe at concentrations of 5 mM, which is roughly an order of magnitude higher than for other cationic dyes used previously for the same purpose, in order to minimise electromigrational dispersion. Baseline instability was minimised by a combination of coating the capillary with poly(ethyleneimine), addition of a neutral polymer to the electrolyte, and the application of a small amount (20 mbar) of hydrodynamic pressure during the separation. Separation of a mixture containing alkali metals, alkaline earths, transition metals and lanthanides was achieved by the addition of 2-hydroxyisobutyric and lactic acid as complexing agents. Excellent peak shapes were observed over a wide range of analyte mobilities due to the moderate mobility of the probe. The high absorptivity (26733 l mol(-1) cm(-1)) provided by chrysoidine in comparison with typically used, less absorbing probes, was reflected in limits of detection which were typically less than 0.5 microM. These are amongst the lowest reported using hydrodynamic injection without the use of large volume stacking methods. The use of 2-hydroxyisobutyric and lactic acids as complexing agents at pH values close to their pKa values provided suitable buffering which was highlighted by very good reproducibility of migration time, corrected peak area and peak height.     

Effects of Cetyltrimethylammonium Bromide and Heptane on the Surface Properties and CO2 Adsorption of Zeolite NaX

Zeolite X was synthesized by the gelation method for use as a CO₂ adsorbent. The zeolite was prepared from a sodium silicate solution and Al(OH )₃ as silicon and aluminum source, respectively. The effects of cetyltrimethylammonium bromide (CTAB ) and heptane addition on surface properties, morphology, and CO₂ adsorption capacities were investigated. The CO₂ adsorption capacity of the synthesized zeolite with the addition of CTAB and heptane increased as demonstrated by the higher CO₂ uptake (3.00 mmol/g), which was due to the higher surface area and pore volume. Interaction between CTAB micelles and sodium cations with aluminosilicate anions led to an increase in the nucleation rate and smaller crystalline sizes. The addition of heptane resulted in higher positively charged CTAB micelles and improved the affinity between the micelles and aluminosilicate anions.     

Flow injection calibration methods for atomic absorption spectrometry

The use of an atomic absorption spectrometer as a detector in flow injection analysis is briefly reviewed. A new simplified model is described for the dispersion effects observed with such systems; the model is based on considering the dispersion to be due to a single hypothetical mixing chamber located immediately prior to the measurement stage. The utility of this approach is demonstrated for two methods of calibration commonly used in atomic absorption spectrometry, and it is shown that flow injection sample and standard handling techniques are comparable to manipulation with volumetric apparatus. The flow injection method has a number of advantages for the analogue of the standard addition method. The use of an exponential concentration gradient is proposed as a novel method of calibration using a single concentrated standard. Results are presented for the determination of chromium in standard steels.     

Studies on sustained-release suppositories. I. Effect of alginic acid addition on rectal absorption of bacampicillin in rabbits

Sustained-release suppositories of bacampicillin (BAPC) were prepared by the use of the adduct which was precipitated from an aqueous solution containing BAPC and alginic acid (Alg). As the suppository base, Witepsol H-15 and macrogol were used. Absorptions of BAPC from the suppositories were prolonged in rabbits, but the bioavailabilities were decreased compared to that after administration of BAPC alone. However, these absorptions were improved enormously by the addition of surface-active agents, that is, an excellent prolonged absorption and high bioavailability were obtained. Interestingly, similar prolonged absorption could be obtained only by mixing Alg with BAPC in a suppository base. Further, this absorption rate was found to be controlled by the amount of Alg addition. The absorption profiles from a suppository containing the mixture differed from that containing the adduct in exhibiting both high plasma level and prolonged absorption. This may be due to simultaneous fast absorption of BAPC itself and formation of the adducts. Thus, it seemed that BAPC preparations containing Alg may be practically useful as a rectal preparation with prolonged action and giving a high plasma level.     

Aerobic Oxidative N-Heterocyclic Carbene Catalysis

The ease with which simple starting materials can be transformed into highly functionalized products has made oxidative N-heterocyclic carbene (NHC) catalysis an area of significant interest. However, the use of stoichiometric amounts of high molecular weight oxidants in most reactions generates an undesired equivalent amount of waste. To address this issue, the use of oxygen as the terminal oxidant in NHC catalysis has been developed. Oxygen is attractive due to its low cost, low molecular weight, and ability to generate water as the sole by-product. However, molecular oxygen is challenging to use as a reagent in organic synthesis due to its unreactive ground state, which often requires reactions to be run at high temperatures and results in the formation of kinetic side-products. This review covers the development of aerobic oxidative carbene catalysis, including NHC-catalyzed reactions with oxygen, strategies for oxygen activation, and selectivity issues under aerobic conditions.     

Direct Catalytic Addition of Alkylnitriles to Aldehydes by Transition‐Metal/NHC Complexes

Direct catalytic addition of alkylnitriles to aldehydes allows for an atom‐economical access to β‐hydroxynitriles under proton transfer conditions. Direct use of alkylnitriles as pronucleophiles has been hampered due to their low acidity resulting in an inability to generate α‐cyano carbanions in a catalytic manner. A transition metal/N‐heterocyclic carbene (NHC) complex prepared from [{Rh(OMe)(cod)}₂] and an imidazolium‐based carbene was identified as an effective catalyst to promote the reaction with as little as 1.25 mol % of catalyst loading. The corresponding Rh complex, derived from chiral triazolium salt, rendered the reaction enantioselective, albeit with moderate enantioselectivity.     

A factorial design for optimizing a flow injection analysis system

The use of a factorial design for the response exploration of a flow injection (FI) system is described and illustrated by FI spectrophotometric determination of paraquat. Variable response (absorbance) is explored as a function of the factors flow rate and length of the reaction coil. The present study was found to be useful to detect and estimate any interaction among the factors that may affect the optimal conditions for the maximal response in the optimization of the FI system, which is not possible with a univariate design. In addition, this study showed that factorial experiments enable economy of experimentation and yield results of high precision due to the use of the whole data for calculating the effects.     

A factorial design for optimizing a flow injection analysis system

The use of a factorial design for the response exploration of a flow injection (FI) system is described and illustrated by FI spectrophotometric determination of paraquat. Variable response (absorbance) is explored as a function of the factors flow rate and length of the reaction coil. The present study was found to be useful to detect and estimate any interaction among the factors that may affect the optimal conditions for the maximal response in the optimization of the FI system, which is not possible with a univariate design. In addition, this study showed that factorial experiments enable economy of experimentation and yield results of high precision due to the use of the whole data for calculating the effects.