Self-mixing interference effect of DFB semiconductor lasers

This paper analyzes the self-mixing interference in DFB (distributed feedback) semiconductor lasers. The general expression of the threshold gain and frequency in the DFB lasers was deduced. Numerical simulations indicate that, for specific coupling coefficient and cavity length value, the DFB lasers are more sensitive to optical feedback than the Fabry–Perot semiconductor laser. These results show that high-accuracy self-mixing sensors can be obtained by using the DFB lasers. PACS 42.55.Px; 42.60.Lh; 42.87.Bg     

A simple model for optimization design of high performance In1−x−y Ga y Al x As strained MQW DFB lasers

It is well known that complex rate equations and the couple wave equation have to be solved by the method of iteration in the simulation of multi-quantum well (MQW) distributed feedback Bragg (DFB) lasers, and a long CPU time is needed. In this paper, from the oscillation condition of lasers, we propose a simple and fast model for optimization of In_1–x–y Ga _y Al _x As strained MQW DFB lasers. The well number and the cavity length of 1.55 m wavelength In_1–x–y Ga _y Al _x As MQW DFB lasers are optimized using the model. As a result, the simple model gives almost the same results as the complex one, but 90% CPU time can be saved. In addition, a low threshold, high maximum operating temperature of 550–560 K, and high relaxation oscillation frequency of over 30 GHz MQW DFB laser is presented.     

Influence of the UV-induced fiber loss on the distributed feedback fiber lasers

It was found that the output power of the distributed feedback fiber lasers would be improved after annealing or left unused for several days after the laser had been fabricated, and the output of the fundamental mode would not increase but be clamped while the ±1 order modes would be predominant with the enhancement of the coupling coefficient during the fabrication. The paper discussed the influence of UV-induced fiber loss on the fiber phase-shifted DFB lasers. Due to the gain saturation and fiber internal loss, which included the temperament loss and permanent loss, there was an optimum coupling coefficient for the DFB fiber lasers that the higher internal fiber loss corresponded to the lower optimum values of coupling coefficient.     

Continuous wave,distributed feedback diode laser based sensor for trace-gas detection of ethane

The development of a continuous wave (CW), thermoelectrically cooled (TEC), distributed feedback (DFB) laser diode based spectroscopic trace-gas sensor for ultra-sensitive and selective ethane (C₂H₆) concentration measurements is reported. The sensor platform used tunable diode laser absorption spectroscopy (TDLAS) based on a 2f wavelength modulation (WM) detection technique. TDLAS was performed with a 100 m optical path length astigmatic Herriott cell. For an interference free C₂H₆ absorption line located at 2976.8 cm⁻¹ a 1σ minimum detection limit of 240 pptv (part per trillion by volume) with a 1 second lock-in amplifier time constant was achieved. In addition, reliable and long-term sensor performance was obtained when operating the sensor in an absorption line locked mode.     

Modeling and analysis of birefringence in magneto-optical thin film made by SiO2/ZrO2 doped with ferrite of cobalt

We report the device characteristics of the metal–dielectric high-reflectivity (HR) coated 1.55 μm laterally coupled distributed feedback (DFB) laser with metal surface gratings by using holographic lithography. The HR coating films are composed of Au/Ti/SiO₂. It provides a variety of advantages compared to the uncoated DFB laser on the same processed wafer while there is no degradation on current–voltage characteristics. For 3 μm wide and 300 μm long HR coated DFB laser, it exhibits a maximum output power of ∼17 mW and a threshold current of 14.2 mA at 20°C under continuous-wave mode. It is clear that the threshold current and slope efficiency are improved by 36% and 96%, respectively, due to the reduction of mirror loss. The metal–dielectric HR coating on one facet of DFB laser is found to have significantly increased characteristic temperature (i.e., T ₀∼88 K). Furthermore, the stable single-mode operation with an increased single-mode suppression ratio was achieved.     

分布反馈量子级联激光器光栅反馈特性北大核心CSCD

为探究Bragg光栅结构对TM模反馈特性的影响,利用有限时域差分法对具有TM模的分布反馈(DFB)量子级联激光器Bragg光栅结构进行仿真研究。重点分析了侧向耦合光栅的光学特性以及光栅侧壁倾角对光栅反射谱、损耗的影响及原因,并探究了光栅刻蚀深度及占空比与TM模的耦合系数、损耗的关系。结果表明有效折射率是影响Bragg波长的主要因素,而光限制因子是不同周期的侧向耦合光栅结构耦合系数产生巨大差别的原因,当光栅侧壁倾角90°时镜面损耗最小。光栅周期、占空比、刻蚀深度与耦合系数的关系表明:这些参数不仅影响光栅的相对介电常数,也会对光限制因子产生作用,从而影响耦合系数的大小;耦合系数与刻蚀深度具有正比关系,大周期光栅耦合系数随占空比的变化率较小。对光栅光反馈特性的理论研究有利于提升对DFB量子级联激光器的认识,促进激光器性能的提升和发展。     

Intensity-induced nonlinear effects in UV window materials

Intensity-induced nonlinear effects in optical window materials have been investigated at 308 nm. The absolute two-photon absorption coefficients for fused silica, CaF₂, BaF₂, Al₂O₃ and ADP crystals have been measured by using a single 120 ps, transform-limited pulse from the second harmonic of a distributed feedback (DFB) dye laser. The nonlinear refractive index coefficient has been obtained from measurements of far-field intensity distributions.     

CO2-laser gas discharges in narrow gaps

We have studied RF discharges as excitation mechanisms for distributed feedback (DFB) CO₂ lasers. For CO₂ laser plasmas the reduced electric fieldE/N has to be in a well-defined range. The reduced electric fieldsE/N of gas discharges in the narrow gaps with widths of the order of 100 m required for DFB are considerably above this range. In order to study the feasibility of these RF-excited discharges for DFB CO₂ lasers we have measured the electron temperatureT _e in their plasmas. From helium-line-intensity ratios we have deduced a lower limit of the electron temperatureT _e of 4eV. The observed high intensities of bands of singly ionized nitrogen indicate an even higher electron temperature, but an efficient pumping of the upper laser level is not possible with an electron temperature above 2.5 eV.We have estimated the electron densityn _e and the current densityj _e from ratios of the intesities of forbidden and allowed helium lines. The high current densityj _e is in the range of abnormal glow discharges.In the gas discharges between narrow gaps the electron oscillation amplitudex _e is large than the electrode separationd. In order to replace the resulting high electron losses a high electron temperatureT _e is necessary to sustain the gas discharge. Because of this high electron temperatureT _e an efficient pumping of the upper laser level is not possible.     

A horn ridge waveguide DFB laser with reduced spatial hole burning for high-speed modulation

In this paper, we propose a DFB laser with a horn ridge waveguide (HRW) to suppress the longitudinal spatial hole burning (LSHB) effect in the lasers cavity, thus to reduce the rolloff at low frequency. The simulation result shows that HRW DFB lasers could significantly suppress the LSHB effect and its modulation bandwidth is increased by 14% comparing with the conventional straight ridge waveguide (RW) DFB lasers when the normalized coupling coefficient (κL) is 3.0. The calculated eye diagrams of HRW DFB lasers under direct 25 Gbps modulation have clearer opening than that of the conventional RW DFB lasers. These superior properties are due to the suppression of the LSHB effect by the HRW structure.     

Diode laser measurement of line strengths and air-broadening coefficients of CO2 and CO in the 1.57 μm region for combustion diagnostics

Spectral measurements of two line pairs of CO₂ and CO in the temperature range 300–1000 K at 1.573 µm were performed using a fiber-coupled distributed feedback (DFB) diode laser. The two line pairs can be used in a tunable diode laser (TDL) absorption sensor for simultaneously detecting CO₂ and CO gas in a single scan of the diode laser. The spectral parameters (line strengths, air-broadening coefficients and the temperature exponent n) of the two pairs are presented. The measured data agree well with existing databases (HITRAN 2004 and HITRAN 2008), the discrepancies being less than 5% for most of the probed transitions. Although the HITRAN database is a useful tool for sensor design, we found that laboratory measurements of the spectroscopic data for the line pair selected for high-temperature sensors are necessary for establishing the uncertainty for accurate measurements.     

6 MHz BAW resonators fabricated using new piezoelectric crystals PrCa4O(BO3)3 and NdCa4O(BO3)3

Thickness shear mode Bulk Acoustic Wave (BAW) resonators with frequency of 6 MHz, were fabricated using monoclinic piezoelectric crystals PrCa₄O(BO₃)₃ (PrCOB) and NdCa₄O(BO₃)₃ (NdCOB). Zero temperature coefficient of frequency (TCF) characteristics were achieved over the temperature range of –140 °C to 200 °C for (YXt)–1.5° cut PrCOB and (YXt)15° cut NdCOB, with the turnover temperature at 20 °C. The electromechanical coupling factor k₂₆ and the piezoelectric coefficient d₂₆ were determined to be 30.2% and 15.8 pC/N for PrCOB, 29.0% and 15.1 pC/N for NdCOB resonators, respectively. The temperature independent frequency behavior, large coupling factor, high piezoelectric coefficient, together with noticeable mechanical quality factors (Q > 2,500), make PrCOB and NdCOB crystals good candidates for sensing applications with expanded temperature usage range. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

多间隙耦合腔中注-波同步与耦合

本文基于空间电荷波理论,导出了N间隙耦合腔中注-波耦合系数和电子注电导计算公式.通过计算分析多间隙耦合腔中工作模式(2π模)耦合系数和归一化电子注电导随间隙数目N、直流电压和导流系数的变化,研究多间隙耦合腔中注-波耦合和同步关系,对分布互作用速调管的理论研究有指导意义. 关键词： 多间隙耦合腔 耦合系数 电子注电导 同步与耦合     

Frequency stabilization of a frequency-doubled 197.2 THz distributed feedback diode laser on rubidium 5S1/2→7S1/2 two-photon transitions

A 197.2 THz (1520.2 nm) ITU-T grid distributed feedback (DFB) diode laser is frequency stabilized at 197.198 THz by 1ocking its second harmonic (SH) signal on the rubidium 5S_1/2→7S_1/2 two-photon transition at 394.396 THz (760.1 nm). With 100 mW from the DFB diode laser and amplifying by an erbium-doped fiber amplifier, we obtain an SH power of 15 mW using a periodically poled lithium niobate (PPLN) waveguide frequency doubler. The stability was 2×10⁻¹¹ (10 s), corresponding to a frequency variation of 4 kHz at 1520.2 nm. Our scheme provides a compact and high performance frequency reference in the communication band.     

基于相位采样光栅的双波长光纤激光器

提出一种基于相位采样的分布反馈式双波长光纤激光器,在不同的空间化置同时引入相位和采样周期的突变.通过理论分析,这种结构能够实现谐振腔的分离,使不同波长的光波利用不同空间位置的增益介质,克服增益介质均匀加宽引起的模式竞争,实现双波长激射.采用准分子激光器和均匀相位模板,在掺铒光纤上制作波长差为0.46 nm的舣波长光纤激光器,能够实现舣波长激射.通过实验,对激光器输出功率和光栅强度的关系进行研究,表明输出功率和光栅强度成反比.     

A new mechanism for the anomalous hall coefficient with application to liquid metals

The effect of spin-orbit coupling of conduction electrons on the Hall coefficient of liquid metals is studied and a new mechanism for the anomalous Hall coefficient is suggested. S.O. coupling causes asymmetric scattering and a current, perpendicular to the magnetic field and to the electric field, is set up. This leads to an additional Hall coefficient , as was first calculated by Luttinger. But S.O. coupling also causes a dipole to appear near each ion, leading to an electrical polarization and an additional Hall coefficient,R _so.R _so is calculated for liquid normal metals and transition metals to first order in S.O. coupling. In normal metals,R _so and are proportional to the Pauli susceptibility. Both are positive for electron-like charge carriers. S.O. coupling leads to a maximum deviation from nearly free electron value in the Hall coefficient of a heavy, four or five-valent liquid metal with short mean free path. In transition metals, different expressions are obtained forR _so depending whether localized moments are present (magnetic model) or not (non-magnetic model). The sign ofR _so is determined by the value of thed-phase shift alone.R _so is proportional to the susceptibility ofd-electrons and can be large, leading to a positive Hall coefficient in the liquid transition metal.     

Circuit model for absorption grating gain-coupled distributed feedback semiconductor lasers

A circuit model for absorption grating (AG) gain-coupled (GC) distributed feedback (DFB) semiconductor laser diodes (LD) is presented, based on the rate equations of carrier densities in active region and absorption grating, as well as the photon density. The relation of photon lifetime to cavity loss and facet loss, and the relation of light power to average photon density are derived. As an example, self-pulsation in AG–GC–DFB–LD is studied.     

Stability of astigmatic and twisted optical lensguides

We investigate single mode yield above threshold for index coupled distributed feedback (DFB) lasers and compare that with spatial hole burning (SHB) corrected yield at threshold. If the criterion necessary for the SHB corrected yield is selected properly, the two yields give good agreements. For antireflection-high reflection (AR–HR) facets, the value of coupling strength, L, which gives the highest single mode yield above threshold is approximately 0.9. In this case, the reflectivity of the AR facet should be less than 1.5     

Threshold current density in ZnS/MgBeZnS quantum well ultraviolet lasers

We calculate optical gain coefficient and threshold current density in ZnS/MgBeZnS quantum wells (QWs) because ZnS/MgBeZnS QWs are useful for the fabrication of an ultraviolet laser on zinc-blende substrates. The threshold current density in a ZnS/MgBeZnS QW laser diode (LD) with a 10 nm ZnS active layer is calculated to be 1.63 kA/cm². By comparing the measured J _th in a CdZnSe/ZnSSe/ZnMgSSe QW LD with that calculated by us, it is expected that the threshold current density in ZnS/MgBeZnS QW LDs measured by experiment is larger than that calculated by our calculation method.     

Stress and magnetic properties of surfaces and ultrathin films

Stress measurements with sub-monolayer sensitivity are performed to investigate the correlation between mechanical film stress and magneto-elastic anisotropy in epitaxial ferromagnetic monolayers. The magneto-elastic coupling B₁ of Fe(1 0 0) films is measured directly. Magnitude and sign of B₁ deviate from the respective bulk value. A strain-dependent correction of the magneto-elastic coupling coefficient B₁ describes the apparent thickness dependence of B₁ for film thicker than 10 nm. For thinner films, the possible contribution of surface corrections is discussed to explain the almost constant B₁. The implications of a modified magneto-elastic coupling for the anisotropy of ultrathin films is elucidated.     

Coupling coefficients of gratings with graded refractive index waveguides

In this paper, the effective coupling coefficient κeff and the self-coupling coefficient ζ1 are introduced to describe the characteristic of gratings in a resonant situation when the effects of radiation and other partial waves coupling are considered. The dependence of these two coupling coefficients on grating tooth shapes and depths and the dimensions of graded refractive index (GRIN) waveguides is numerically analysed. The results show that the gratings with linear GRIN waveguides have the largest |κeff|. The possibility of realizing a complex-coupled DFB laser, even a pure gain or loss coupled DFB laser, employing only a real refractive index coupled grating is also discussed. This revised version was published online in November 2006 with corrections to the Cover Date.