Development of Cocatalysts for Photocatalytic Overall Water Splitting on (Ga1? x Zn x )(N1? x O x ) Solid Solution

The development of cocatalysts promoting overall water splitting on (Ga_1−x Zn _x )(N_1−x O _x ) solid solution photocatalyst is presented. The (Ga_1−x Zn _x )(N_1−x O _x ) is a stable visible-light-driven photocatalyst for stoichiometric water splitting upon loading with a suitable nanoparticulate cocatalyst. Loading with a combination of Cr and Rh oxides, Rh_2−y Cr _y O₃, is demonstrated to raise the quantum efficiency of (Ga_1−x Zn _x )(N_1−x O _x ) for overall water splitting to 2.5% at 420–440 nm. This represents a 10-fold increase in efficiency over the highest efficiency previously obtained using nanoparticulate RuO₂ as a cocatalyst. In addition to the composition, the dispersion and size of cocatalyst nanoparticles are identified as important factors affecting the degree of enhancement for stoichiometric water splitting. Kazuhiko Maeda—Research Fellow of the Japan Society for the Promotion of Science (JSPS).     

Phase composition, electroconductivity, oxygen ion transport number, and microhardness of Ln1 ? xSrxGa0.5 ? y/2Al0.5 ? y/2MgyO3 ? δ (Ln = La, Pr, Nd; x, y = 0.10, 0.15)

Phase composition, electroconductivity, oxygen ion transport number, and microhardness of samples of Ln_{1 − x} Sr_xGa_{0.5 − y/2}Al_{0.5 − y/2}Mg_yO_{3 − δ} (Ln = La, Pr, Nd; x, y = 0.10, 0.15) synthesized by a ceramic methods are studied. Methods of x-ray diffraction analysis and scanning electron microscopy reveal the La-containing samples to be homogeneous and have a perovskite structure. Magnesium does not dissolve in Pr-and Nd-containing systems but forms an individual phase based on magnesium oxide. Apart from magnesium oxide, in these systems there form extrinsic phases, specifically, LnSrGa₃O₇ and an unknown phase. The electroconductivity of La_{1 − x} Sr_xGa_{1 − y} Mg_yO_{3 − δ} decreases after substituting Al for Ga. Ceramic La_{1 − x} Sr_xGa_{0.5 − y/2}Al_{0.5 − y/2}Mg_yO_3−δ is a purely ionic conductor in the temperature interval 500 to 1000°C; Nd_xSr_xGa_{0.5 − y/2}Al_{0.5 − y/2}Mg_yO_{3 − δ} has predominantly ionic conduction; and the predominant type of conduction in Pr_{1 − x} Sr_xGa_{0.5 − y/2}Al_{0.5 − y/2}Mg_yO_{3 − δ} is electronic below 700–800°C, with the contribution of ionic conduction increasing at higher temperatures. Substituting Al for Ga raises the hardness of ceramics under study. Among the compositions studied, La_0.85Sr_0.15Ga_0.45Al_0.45Mg_0.10O_{3 − δ} and La_0.85Sr_0.15Ga_0.425Al_0.425Mg_0.15O_{3 − δ} exhibit a combination of electroconductivity and hardness that is optimal for application as electrolyte at reduced temperatures (600–800°C). The Pr_{1 − x} Sr_xGa_{0.5 − y/2}Al_{0.5 − y/2}Mg_yO_{3 − δ} system possesses mixed ionic-electronic conduction and high hardness, which makes it appealing for application as oxygen-penetrable membranes. Original Russian Text ? Yu.V. Danilov, A.D. Neuimin, L.A. Dunyushkina, L.A. Kuz’mina, N.S. Zybko, Z.S. Martem’yanova, A.A. Pankratov, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 1, pp. 57–65.     

Glycine-assisted hydrothermal synthesis of nanostructured Co x Ni1−x –Al layered triple hydroxides as electrode materials for high-performance supercapacitors

Nanostructured Co _x Ni_1−x –Al layered triple hydroxides (Co _x Ni_1−x –Al LTHs) have been successfully synthesized by a facile hydrothermal method using glycine as chelating agent. The samples were characterized by X-ray diffraction, thermogravimetry, Fourier transform infrared spectroscopy and scanning electron microscopy. The morphologies of Co _x Ni_1−x –Al LTHs varied with the Co content and its effect on the electrochemical behavior was studied by cyclic voltammetry and galvanostatic charge–discharge techniques. Electrochemical data demonstrated that the Co _x Ni_1−x –Al LTHs with Co/Ni molar ratio of 3:2 owned the best performance and delivered a maximum specific capacitance of 1,375 F g⁻¹ at a current density of 0.5 A g⁻¹ and a good high-rate capability. The capacitance retained 93.3% of the initial value after 1,000 continuous charge–discharge cycles at a current density of 2 A g⁻¹.     

Conductivity,oxygen interfacial exchange and diffusion in oxides based on lanthanum gallate

The method of isotopic exchange was used to study the oxygen exchange kinetics in the oxides of La_0.88Sr_0.12Ga_0.82Mg_0.18O_{3 − δ} and La_0.80Sr_0.20Ga_0.85−x Mg_0.15Co _x O_{3 − δ} (x = 0.05, 0.15, 0.20, 0.25). The rates of oxygen exchange and its diffusion coefficients were determined in the temperature range of 600–900°C at the oxygen pressure of 5 torr. The fractions of the three exchange types for the oxides studied were determined at the temperature of 817°C and oxygen pressure of 5 torr. The total conductivity of the oxides of La_0.80Sr_0.20Ga_0.85−x Mg_0.15Co _x O_{3 − δ} (x = 0.05, 0.15, 0.20, 0.25) was measured in the temperature range of 550–850°C in air and at the temperature of 800°C in the range of oxygen pressures of 1–760 torr. It was shown that an increase in the electronic conductivity component due to an increase in the cobalt fraction in the gallium sublattice results in growing interfacial exchange rate, total conductivity of the studied systems, and a decrease in the effective conductivity activation energy.     

Interface microstructure and diffusion kinetics in diffusion bonded Mg/Al joint

The interface microstructure, formation of diffusion bonded joint and regulation of atom diffusion were studied by means of scanning electron microscope (SEM), energy dispersion spectroscopy (EDS) and electron probe microanalyser (EPMA). The experimental results indicated that an obvious interfacial transition zone was formed between Mg and Al, and there are three intermetallic layers Mg₁₇Al₁₂, MgAl and Mg₂Al₃ in this zone. Diffusion activation energy of Mg and Al in the above layers was lower than that in the Mg and Al base metals. The thickness (x) of each layer can be expressed as x ² = 4.14exp(−28780/RT)(t−t ₀), x ² = 31.4exp(−25550/RT)(t−t ₀) and x ² = 0.6exp(−22600/RT)(t−t ₀) corresponding to Mg₁₇Al₁₂, MgAl and Mg₂Al₃ with heating temperature (T) and holding time (t).     

Effect of metal substitution for cobalt on the oxygen adsorption properties of YBaCo<Subscript>4</Subscript>O<Subscript>7</Subscript>

YBaCo₄O₇ compound is capable to intake and release a large amount of oxygen in the temperature range of 200–400°C. In the present study, the effect of Zn, Ga and Fe substitution for Co on the oxygen adsorption/desorption properties of YBaCo₄O₇ were investigated by thermogravimetry (TG) method. Due to fixed oxidation state of Zn2+ ions, the substitution of Zn²⁺ for Co²⁺ suppresses the oxygen adsorption of YBaCo_4−xZn_xO₇. The substitution of Ga³⁺ for Co³⁺ also decreases the oxygen absorption capacity of YBaCo_4−xGa_xO₇. This can be explained by the strong affinity of Ga³⁺ ions towards the GaO₄ tetrahedron. Compared with Zn- and Ga-substituted samples, the drop of oxygen adsorption capacity is smallest for Fe-substituted samples because of the similar changeability of oxidation states of Co and Fe ions.     

Structure of complex salts [Co(NH3)6][Rh(NO2)6] and [Co(NH3)6][(NO2)3Rh(μ-NO2)1+x(μ-OH)2?xRh(NO2)3]·(2-x)(H2O), x = 0.17

The structures of two salts [Co(NH₃)₆][Rh(NO₂)₆] (I) and [Co(NH₃)₆][(NO₂)₃Rh(μ-NO₂)_1+x (μ-OH)_2−x Rh(NO₂)₃]·(2−x)(H₂O), x = 0.17 (II) are solved. Single crystals of the salts are obtained by the counter diffusion method through the gel of aqueous solutions of [Co(NH₃)₆]Cl₃ and Na₃[Rh(NO₂)₆]. The structure of [Co(NH₃)₆][Rh(NO₂)₆] is consistent with the diffraction data for a polycrystalline sample of poorly soluble fine salt formed in the exchange reaction between aqueous solutions of [Co(NH₃)₆]Cl₃ and Na₃[Rh(NO₂)₆]. The structure of [Co(NH₃)₆][(NO₂)₃Rh(μ-NO₂)_1+x (μ-OH)_2−x Rh(NO₂)₃]·(2−x)(H₂O), x = 0.17 exhibits the stabilizing effect of a large cation in the formation of novel, unknown previously coordination ions: [(NO₂)₃Rh(μ-NO₂)(μ-OH)₂Rh(NO₂)₃]³⁻ and [(NO₂)₃Rh(μ-NO₂)₂(μ-OH)Rh(NO₂)₃]³⁻.     

Synthesis and photocatalytic properties of low-dimensional cobalt-doped zinc oxide with different crystal shapes

The glycoxide complexes Zn_1–x Co _x (HCOO)(HOCH₂CH₂O)_1/2 and Zn_1−x Co _x (OCH₂CH₂O) (0 ≤ x ≤ 0.3) have been synthesized by heating ethylene glycol solutions of zinc formate Zn(HCOO)₂ · 2H₂O or its mixtures with cobalt formate Co(HCOO)₂ · 2H₂O. The crystals of these complexes have the shape of filaments (needles, bars) and distorted octahedra, respectively. A new method in which these complexes are used as the precursor is suggested for the synthesis of low-dimensional wurtzite-like Zn_1−x Co _x O. The shape of the precursor crystals is fully inherited by Zn_1−x Co _x O resulting from their heat treatment. The Zn_1−x Co _x O solid solutions show high photocatalytic activity in hydroquinone oxidation in aqueous solution under UV or blue light irradiation, and their activity increases as their cobalt content is increased.     

State of atoms and interatomic interactions in complex perovskite-like oxides: XXX. Influence of the nature of diamagnetic substituents on the dynamics of clustering in lanthanum gallate doped with strontium,chromium, and magnesium

The fractions of clusters and single chromium atoms were calculated by the diluted solution and Heisenberg-Dirac-van-Vleck models for a series of solid solutions containing chromium, strontium, and magnesium in the ratio 5:1:1, respectively. A principal genetic relationship was revealed between La_1−0.2x Sr_0.2x ·Cr _x Ga_1−x O_3−δ, La_1−0.5x Sr_0.5x Cr _x Ga_1−x O_3−δ, and La_1−0.2x Sr_0.2x Cr _x Ga_1−1.2x Mg_0.2x O_3−δ systems. Deviations from Curie-Weiss law are observed for the systems with the ratio [Cr]:[Sr]:[Mg]=5:1:1, which point to a noncompensated magnetic moment.     

Effect of epitaxial growth on the formation of the cobalt catalysts of the Fischer-Tropsch synthesis

Mixed oxides Co_xAl_yO₄ with different Al/Co ratios applied as supports for the catalysts of the Fischer-Tropsch synthesis were prepared using the solid-state chemical reaction. The Co_xAl_yO₄ supports were prepared by modifying gibbsite with various cobalt salts (acetate, nitrate, and basic carbonate). The use of basic cobalt carbonate gives the Co(20%)/Co_xAl_yO₄ catalyst, which provides an increased yield of hydrocarbons C₅₊ and a decreased methane content compared to the impregnation catalyst Co(30%)/Al₂O₃. The introduction of small amounts of rhenium additives makes it possible to enhance the yield of hydrocarbons C₅₊ (179 g m⁻³) and also to increase the selectivity with respect to the C₅–C₁₈ fraction. The introduction of basic cobalt carbonate into the support, most likely, creates favorable conditions for the epitaxial growth of the precursor of the active phase. Dedicated to Academician G. A. Abakumov on the occasion of his 70th birthday. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 9, pp. 1856–1860, September, 2007.     

Structural and low temperature Raman scattering studies in SrTi<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Co<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript>3</Subscript> nanoparticles synthesized by sol–gel method

We investigate effects of Co dopant concentration on the structure and low temperature Raman scattering properties in SrTi_1−x Co _x O₃ (x = 0.00, 0.10, 0.20, 0.30) nanoparticles prepared by sol–gel method. The dopant induced changes are studied by XRD, and Raman scattering measurements. The results show an average particle size of about 20 nm depending on the Co content and the lattice parameters decrease as increasing the Co content. In the Raman spectra, a broad structure in the region 100–500 cm⁻¹ is almost absent and the peaks in the region 600–800 cm⁻¹ show different weights with respect to SrTiO₃, relating to structural changes. The anomalous change in the area ratio of Raman peaks as function of temperature suggests a phase transition in our samples in the range of 110–130 K. These results indicate that the Co ion has replaced the site of Ti in unit cell. This novel route also demonstrates the advantage of synthesizing the compound with low annealing temperature.     

Magnetic properties of fullerene salts containing d- and f-metal cations (Co2+, Ni2+, Fe2+, Mn2+, Eu2+, Cd2+). Specific features of the interaction between C60·? and the metal cations

The interaction between the radical anions C₆₀ ^·− and divalent d- and f-metal (Co, Fe, Ni, Mn, Eu, Cd) cations in DMF and acetonitrile-benzonitrile (AN-BN) mixture was studied. Black solid polycrystalline salts (C₆₀ ^·−)₂{(M²⁺)(DMF) _x } (x = 2.4–4, 1–6) containing the radical anions C₆₀ ^·− and metal(ii) cations solvated by DMF were prepared for the first time and their optical and magnetic properties were studied. The salts containing Co²⁺, Fe²⁺, and Ni²⁺ are characterized by antiferromagnetic interactions between the radical anions C₆₀ ^·−, which result in unusually large broadening of the EPR signal of C₆₀ ^·− upon lowering the temperature (from 5.55–12.6 mT at room temperature to 35–40 mT at 6 K for Co²⁺ and Ni²⁺). The salts containing Mn²⁺ and Eu²⁺ form diamagnetic dimers (C₆₀ ⁻)₂, which causes a jumpwise decrease in the magnetic moment of the complexes and disappearance of the EPR signal of C₆₀ ^·− in the temperature range 210–130 K. A feature of salt 6 is magnetic isolation of the radical anions C₆₀ ^·− due to the presence of diamagnetic cation Cd²⁺. The salts prepared are unstable in air and decompose in o-dichlorobenzene or AN. Reactions of C₆₀ ^·− with metal(ii) cations in AN-BN mixture result in decomposition products of the salts that contain neutral fullerene dimers and metals solvated by BN. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 9, pp. 1909–1919, September, 2008.     

Calculated properties of neutral and charged Al<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript>Co<Subscript><Emphasis Type="Italic">m</Emphasis></Subscript> clusters by density functional theory

Density functional calculations are performed to study the structures and electronic properties of Al _n Co _m clusters with n = 1–7 and m = 1–2. Frequency analysis is also performed after structural optimization to make sure that the calculated ground states are real minima. The corresponding total and binding energies, adiabatic electron affinities and ionization potentials are presented and discussed to aid the identification of our calculations. The BSSE correction is also considered in our calculation. Among Al _n Co _m , Al _n Co _m ⁻, and Al _n Co _m ⁼ clusters (n = 1–7 and m = 1–2), Al₄Co⁻, Al₆Co⁻, Al₂Co₂, and Al₆Co₂ are predicted to be more stable. Our results are consistent with the available experimental data.     

Synthesis and magnetic properties of nanocomposite Ni1?xCoxFe2O4–BaTiO3 fibers by organic gel-thermal decomposition process

Nanocomposites of ferrite and ferroelectric phases are attractive functional ceramic materials. In this work, the nanocomposite Ni_1−x Co _x Fe₂O₄–BaTiO₃(x = 0.2, 0.3, 0.4, 0.5) fibers with fine diameters of 3 ~ 7 μm and high aspect ratios were synthesized by the organic gel-thermal decomposition process from the raw materials of citric acid and metal salts. The structure, thermal decomposition process and morphologies of the gel precursors and the resultant fibers derived from thermal decomposition of the gel precursors were characterized by Fourier transform infrared spectroscopy, thermogravimetric differential thermal analysis, X-ray diffraction and scanning electron microscopy. The magnetic properties of the nanocomposite fibers were measured by vibrating sample magnetometer. The nanocomposite fibers of ferrite Ni_1−x Co _x Fe₂O₄ and perovskite BaTiO₃ are formed at the calcination temperature of 900 °C for 2 h. The average grain sizes of Ni_1−x Co _x Fe₂O₄ and BaTiO₃ in the nanocomposite fibers increase from about 15 nm to approximately 67 nm with the increasing calcination temperatures from 900 to 1,180 °C. The saturation magnetization of the nanocomposite Ni_1−x Co _x Fe₂O₄–BaTiO₃(x = 0.2, 0.3, 0.4, 0.5) fibers increases with the increase of grain sizes of Ni_1−x Co _x Fe₂O₄ and Co content, while the coercivity reaches a maximum value at the single-domain size of about 65 nm of Ni_0.5Co_0.5Fe₂O₄ obtained at the calcination temperature of 1,100 °C.     

Physicochemical properties of non-stoichiometric oxides

One of the most important challenges with solid oxide fuel cells (SOFC) is to find cathode materials with high enough catalytic activity for the dissociation of the molecular oxygen. Oxide mixed conductors with the perovskite structure (ABO₃) and high Co content in the B site have been extensively studied to be used as cathode in SOFC. This is the second part of a review of high temperature properties of two mixed conductors systems. The first part was focused on the n = 2 Sr₃FeMO_6+δ (M = Fe, Co, Ni) Rudlesdden Popper phases, while in this paper we discuss the thermodynamic and transport properties of the perovskite solid solution Sr_1−x La _x Fe_0.2Co_0.8O_3−δ (0 ≤ x ≤ 0.4) in the temperature range 773 ≤ T ≤ 1173 K. In particular, the interest has been focused on the x = 0 sample, which exhibits large ionic conductivity values (σ_i ~1 S cm⁻¹), but suffers a structural transformation from cubic to orthorhombic symmetry because the ordering of the oxygen vacancies when the oxygen partial pressure decreases. Measurements of the oxygen chemical potential ( m_\textO2 \mu_{{{\text{O}}_{2} }} ) as function of oxygen content and temperature, coupled with high temperature X-ray diffraction data, permitted us to broaden the knowledge of the T–δ–p(O₂) phase diagram for the x = 0 sample. In addition, we have investigated the effects of the La incorporation on the stability range of the cubic phases of the Sr_1−x La _x Fe_0.2Co_0.8O_3−δ solid solution.     

State of atoms and interatomic interactions in complex perovskite-like oxides: XXXI. Influence of magnesium concentration on chromium atoms state and interatomic interactions in lanthanum gallate doped with chromium and magnesium

Magnetic susceptibility of LaCr _x Ga_1−1.2x Mg_0.2x O_3−δ and LaCr _x Ga_1−1.5x Mg_0.5x O_3−δ solid solutions with the ratios [Cr]:[Mg] = 5:1 and 2:1 was studied. Fractions of clusters and single chromium atoms were calculated for the series of solid solutions with [Cr]:[Mg] = 5:1. The relation of the systems with [Cr]:[Mg] = 5:1 and [Cr]:[Sr]:[Mg] = 5:1:1 was revealed. For the system with [Cr]:[Mg] = 2:1 a temperature dependence of effective magnetic moment was found, which suggests that the exchange parameter is temperature dependent.     

Thermal properties of Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–PbO–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glass system

Thermal behavior of xGa₂O₃–(50 − x)PbO–50P₂O₅ (x = 0, 10, 20, and 30 mol.% Ga₂O₃) and xGa₂O₃–(70 − x)PbO–30P₂O₅ (x = 0, 10, 20, 30, and 40 mol.% Ga₂O₃) glassy materials were studied by thermo-mechanical analysis (TMA) and differential thermal analysis (DTA). Replacement of PbO for Ga₂O₃ is accompanied by increasing glass-transition temperature (263 ≤ T _g/°C ≤ 535), deformation temperature (363 ≤ T _d/°C ≤ 672), crystallization temperature (396 ≤ T _c/°C ≤ 640) and decreasing of coefficient of thermal expansion (5.1 ≤ CTE/ppm K⁻¹ ≤ 16.7). Values of Hruby parameter were determined (0.1 ≤ K _H ≤ 1.3). The thermal stability of prepared glasses increases with increasing of concentration of Ga₂O₃.     

Effect of oxygen nonstoichiometry on kinetics of oxygen exchange and diffusion in lanthanum-strontium cobaltites

The method of isotopic exchange was used to study the kinetics of oxygen exchange and diffusion in complex oxides of La_{1 − x} Sr _x Co_{1 − y} Fe _y O_{3 − δ} (x = 0.0, y = 0.0; x = 0.6, y = 0.2, 0.4). The rates of oxygen interfacial exchange and its diffusion coefficient were determined for LaCoO_{3 − δ} at the pressure of 5 torr in the temperature range of 600–850°C and at the temperature of 700°C in the pressure range of 1–70 torr. The contributions of the three exchange types were calculated. The order of the dependence of the interfacial exchange rate on the oxygen pressure was 0.51 ± 0.01. In the case of La_0.4Sr_0.6Co_{1 − y} Fe _y O_{3 − δ} (y = 0.2, 0.4) in the temperature range of 600–900°C at the oxygen pressure of 10 torr, the oxygen exchange rates and diffusion coefficients were determined in the material bulk and in the subsurface region; contributions of the three types of exchange were calculated. The paper considers the mechanism of oxygen exchange and diffusion as compared to nonstoichiometry in the oxygen sublattice of the La_{1 − x} Sr _x Co_{1 − y} Fe _y O_{3 − δ} oxides.     

A study of YBa2(Cu1?xMex)3O6 + δ (Me = Al, Co, Fe) electrophysical and electrochemical properties

The structure, thermal expansion coefficient, and electroconductivity of YBa₂(Cu_1−x Al _x )₃O_6+δ (x = 0.0–0.9) were studied at 20 to 900°C in air. The most conducting compositions of YBa₂(Cu_1−x Me _x )₃O_6+δ (Me = Al, Co, Fe) were determined. The electrochemical activity of electrodes with the most conducting compositions of YBa₂(Cu_1−x Me _x )₃O_6+δ (Me = Al, Co, Fe) was studied in a wide polarization range in the contact with 0.9ZrO₂ + 0.1Y₂O₃ solid electrolyte in air at the temperatures of 700 to 900°C. Original Russian Text ? V.K. Gil’derman, I.D. Remez, 2009, published in Elektrokhimiya, 2009, Vol. 45, No. 5, pp. 612–615. Published by report at IX Conference “Fundamental Problems of Solid State Ionics”, Chernogolovka, 2008.     

Phase equilibria of the Dy–Al–Si system at 500 °C

The isothermal section at 500 °C of the Dy–Al–Si system was studied in the whole concentration range. The alloys were characterized by X-ray powder diffraction, scanning electron microscopy and electron micro-probe analysis. A few samples were analysed by differential thermal analysis. The following intermetallic compounds, some of them showing variable composition, were found: DyAl₂Si₂ (τ₁), hP5-CaAl₂O₂ structure type, Dy₂Al₃Si₂ (τ₂) mS14-Y₂Al₃Si₂ structure type, Dy₂Al_1+x Si_2−x (τ₃), 0 ≤ x ≤ 0.25, oI10-W₂CoB₂ structure type and Dy₆Al₃Si (τ₄), tI80-Tb₆Al₃Si structure type. A number of binary phases dissolve the third element forming ternary solid solutions: Dy(Al_1−x Si _x )₃, 0 ≤ x ≤ 0.5, hP16-Ni₃Ti structure type, Dy(Al _x Si_1−x )₂, 0 ≤ x ≤ 0.1, oI12-GdSi₂ structure type, Dy(Al _x Si_1−x )_1.67, 0 ≤ x ≤ 0.2, oI12-GdSi₂ structure type, DyAl _x Si_1−x , 0 ≤ x ≤ 0.2, oC8-CrB, and Dy₅(Al _x Si_1−x )₃, 0 ≤ x ≤0.3, hP16-Mn₅Si₃ structure type. The melting point of Dy₆Al₃Si was determined.