Transition metals Fe3+, Ni2+ modified titanium dioxide (TiO2) film sensors fabricated by CPT method to sense some toxic environmental pollutant gases

The present investigation deals synthesis of undoped TiO₂, Ni²⁺ doped TiO₂, and Fe³⁺ doped TiO₂ nanoparticles by low-cost co-precipitation (CPT) method. The thick film sensors of all the fabricated modified TiO₂ nanoparticles were designed by a screen printing strategy. The prepared thick film sensors were characterized by various sophisticated techniques. The structural parameters of undoped TiO₂ and modified TiO₂ film sensors were characterized by X-Ray Diffraction (XRD) which confirmed anatase phase of TiO₂ lattice. The surface morphological properties of all the prepared materials were confirmed by means of scanning electron microscope (SEM). The energy dispersive spectroscopy (EDS) confirms the elemental composition of all the prepared materials. High-Resolution Transmission Electron Microscopy (HR-TEM) was utilized to investigate the crystal lattice of fabricated TiO₂ material. The HR-TEM results revealed the anatase phase crystal morphology of prepared material. The prepared TiO₂ materials were also characterized by means of X-Ray photoelectron spectroscopy (XPS) to confirm the surface doping, specific biding energies, chemical states and elemental composition of modified TiO₂ materials. The Brunauer–Emmett–Teller (BET) study was carried to investigate the specific surface area of all the prepared sensors. The Fe³⁺ doped TiO₂ sensor found with enhanced surface area (83.10 ​m²/g) in comparison to Ni²⁺ doped TiO₂ and bare TiO₂ (67.34 ​m²/g). All the prepared materials were investigated for gas sensing characteristics. The NO₂, SO₂, and CO₂ gases were investigated for all the prepared sensors. The reusability test confirms that the Fe³⁺ doped TiO₂ is reproducible and stable sensor for long time repeated sensing of SO₂ and NO₂ vapors. Importantly, Fe³⁺ doped TiO₂ sensor showed rapid response and recovery towards SO₂ and NO₂ vapors.     

Effect of metal deposition on the photocatalytic activity of titania-silica for the removal of 2-propanol diluted in water

The influence of transition metals, such as Ag, Cr, and Co, on the photocatalytic properties of titania-silica (TiO₂-SiO₂) prepared via both impregnation (imp) and photo-assisted deposition (PAD) methods has been investigated. The decomposition of 2-propanol under UV-light irradiation was used to probe the effect of transition metals deposition on the activity of titania-silica. PAD-Ag/TiO₂-SiO₂ prepared by the PAD method was highly active compared to the original TiO₂-SiO₂, while imp-Cr/TiO₂-SiO₂ prepared by conventional impregnation method showed a weak tendency toward the decomposition of 2-propanol.     

RE/TiO2光催化剂的谱学特性与气相光催化性能的研究

采用改进的sol-gel法和浸渍法制备了TiO₂掺杂稀土离子La³⁺、Y³⁺、Gd³⁺、Er³⁺、Nd³⁺、Pr³⁺的RE/TiO₂光催化剂,运用FTIR、XRD、TEM、低温氮吸附/脱附、TG/DTA、UV-Vis DRS、表面光电压谱(SPS)等进行表征,以气相光催化降解乙烯、溴代甲烷作为探针反应,阐明了RE/TiO₂光催化剂的谱学特性与气相光催化性能的关系。结果显示,稀土离子掺杂后,TiO₂的锐钛矿含量增加,比表面积增大,粒径变小,吸收边发生蓝移,表面光电压的响应阈值增大,此外,Pr³⁺除外的其它稀土离子掺杂的TiO₂的表面光电压信号增强;光催化降解实验表明,与纯TiO₂相比,La³⁺、Y³⁺、Gd³⁺、Er³⁺、Nd³⁺掺杂TiO₂样品上乙烯、溴代甲烷的光催化活性均有不同程度的增强,而且表现出较强的矿化能力。但是,掺杂Pr³⁺的TiO₂的光催化性能降低恰好对应较弱的表面光电压信号。所以,本文认为提高光生电子-空穴对的分离效率是改善光催化性能的关键因素。     

F and Fe co-doped TiO2 with enhanced visible light photocatalytic activity

Four different sols, pure TiO₂, F doped TiO₂, Fe doped TiO₂, and F–Fe co-doped TiO₂ sols, were prepared by peroxidation at low temperature. The crystal structure, morphology, light adsorption, and photocatalytic properties of the pure and doped TiO₂ were examined by X-ray diffraction, transmission electron microscopy, and ultraviolet–visible spectrophotometry. The relationship between the average size, crystal type, range of visible light absorption, and photocatalytic activity and content and type of doped ions were investigated. The results showed that the average size of the F–Fe co-doped TiO₂ composed of both the anatase and rutile phases was the same as that of pure TiO₂. Furthermore, the visible light photocatalytic activity of the F–Fe co-doped TiO₂ was significantly improved over pure TiO₂, F-doped TiO₂, and Fe-doped TiO₂ due to the large red shift in the light adsorption edge.     

锰掺杂硒硫化镉光阳极的制备与光电性能

将适量Se加入到Na2S甲醇水溶液中反应生成Na₂SSe₂阴离子前驱体, 以Cd(NO₃)2、Mn(CH3COO)2为阳离子前驱体, 通过连续离子层吸附反应(SILAR)分别制备出CdSSe₂/TiO₂或 MN²⁺掺杂的Mn-CdSSe₂/TiO₂量子点敏化光阳极。采用拉曼光谱、X射线光电子能谱和能量色散X射线能谱分析确定阴离子前驱体和量子点的价键结构和组成;通过紫外可见吸光光谱表征量子点的光吸收性能;利用J-V曲线和IPCE分别对CdS、CdSSe₂和Mn-CdSSe₂量子点敏化的TiO₂光阳极的光电性能进行了表征。实验结果表明, 采用 0.12 mol·L^-1 Se和0.5 mol·L^-1 Na2S制备的阴离子前驱体、0. 5 mol·L^-1 Cd²⁺和 0.3 mol·L^-1 MN²⁺阳离子前驱体, 通过SILAR法制备的Mn-CdSSe₂/TiO₂光阳极, 能量转换效率比CdSSe₂/TiO₂和CdS/TiO₂光阳极分别提高了90%和247%。     

冷等离子体强化制备TiO2光催化材料及其机理

等离子体技术在材料制备和改性方面的优势得到众多研究者的认可。Ti O2具有化学稳定性高、氧化活性强、生产成本低等优势,被广泛应用于太阳能电池和光催化领域。本文综述了近年来介质阻挡放电等离子体在强化制备Ti O2光催化材料方面的研究成果,包括等离子体辅助制备Ti O2光催化薄膜和Ti O2的等离子体法掺杂两个方面,并分析了其作用机理。从目前的研究成果来看,等离子体技术制得的Ti O2光催化材料具有更好的均匀性和催化活性,这主要得益于等离子体中的高能电子,一方面,Ti O2粒子吸附电子,彼此之间产生静电场的斥力作用,可以抑制颗粒的团聚,另一方面,电子的强还原能力,能够打断Ti-O键,形成氧空位,从而提高其催化性能。     

Pechini based titanium sol as a matrix in TiO<Subscript>2</Subscript> pastes for dye-sensitized solar cell application

The influence that the degree of polyesterification has on a titanium sol (Ti-sol) prepared via the Pechini method that acts as a matrix in TiO₂ pastes used for dye sensitized solar cells is reported. The different content of the polyester in the Ti-sol was realized by varying the heating time of the Ti-sol. Titanium dioxide pastes were prepared by introducing a commercial TiO₂ nanopowder into the Ti-sols. The TiO₂ layers were tested as photoanodes in dye-sensitized solar cells (DSSCs). The most appropriate degree of polyesterification was achieved by heating the Ti-sol for 0.5 and 1 h, while longer heating deteriorates the TiO₂ layer morphology. The highest efficiency of the DSSCs based on an ionic liquid electrolyte was 6.3% measured under standard test conditions (100 mW/cm², AM 1.5, 25 °C).     

钛、铝和玻璃上TiO2光催化膜的失活研究

采用浸渍提拉法，在平行条件下制备了钛、铝和玻璃载体上的TiO₂膜TiO₂ / Ti、TiO₂ / Al和TiO₂ / G，利用X射线光电子能谱(XPS)、原子力显微镜(AFM)和光催化降解实验等手段对膜样品进行了表征和活性评价。实验结果表明，在铝和玻璃基材上制膜时发生了显著的基材元素溢出，使各膜样品的化学组成不同，同时TiO₂粒子和膜表面形貌也因前驱物烧结行为不同而差异较大。TiO_{2相似文献}   

TiO2/Mo-TiO2 的制备、表征和光催化活性

 采用溶胶-凝胶法制备了掺 Mo 的 TiO2 粉末, 再由其制得 TiO2/Mo-TiO2 复合物光催化剂. 使用 X 射线光电子能谱、X 射线衍射、透射电镜、N2 吸附-脱附、紫外-可见漫反射光谱和荧光光谱等手段对催化剂进行了表征. 在紫外光照射下, 以甲基橙溶液降解为探针反应, 研究了 Mo 掺杂量对样品光催化活性的影响. 结果表明, Mo-TiO2 催化剂的活性不如纯 TiO2, 这是因为 Mo 离子促进了光生载流子的复合; 而带有 n-n 异质结半导体结构的 TiO2/Mo-TiO2 复合催化剂具有比纯 TiO2 和 Mo-TiO2 催化剂更高的光催化活性. 当 Mo 掺杂摩尔分数为 2%, TiO2:Mo-TiO2 质量比为 10:1 时, 活性是纯 TiO2 的 1.57 倍.     

锰掺杂硒硫化镉光阳极的制备与光电性能

将适量Se加入到Na₂S甲醇水溶液中反应生成Na₂SSe₂阴离子前驱体, 以Cd(NO₃)₂、Mn(CH₃COO)₂为阳离子前驱体, 通过连续离子层吸附反应(SILAR)分别制备出CdSSe₂/TiO₂或 Mn²⁺掺杂的Mn-CdSSe₂/TiO₂量子点敏化光阳极。采用拉曼光谱、X射线光电子能谱和能量色散X射线能谱分析确定阴离子前驱体和量子点的价键结构和组成;通过紫外可见吸光光谱表征量子点的光吸收性能;利用J-V曲线和IPCE分别对CdS、CdSSe₂和Mn-CdSSe₂量子点敏化的TiO₂光阳极的光电性能进行了表征。实验结果表明, 采用 0.12 mol·L^-1 Se和0.5 mol·L^-1 Na₂S制备的阴离子前驱体、0.5 mol·L^-1 Cd²⁺和 0.3 mol·L^-1 Mn²⁺阳离子前驱体, 通过SILAR法制备的Mn-CdSSe₂/TiO₂光阳极, 能量转换效率比CdSSe₂/TiO₂和CdS/TiO₂光阳极分别提高了90%和247%。     

Preparation and photocatalytic behavior of TiO2-carbon nanotube hybrid catalyst for acridine dye decomposition

A new kind of hybrid catalyst, TiO₂-carbon nanotubes, was prepared via sol-gel method for the first time. Its photocatalytic activity in the photodegradation of acridine dye aqueous solution at low concentration was tested. There was no measurable effect on the formation of crystalline phase of TiO₂ catalyst with the addition of 10 wt.% carbon nanotubes to TiO₂ samples. AFM photograph of TiO₂-carbon nanotubes sintered at 300°C showed that the carbon nanotubes were enwrapped by TiO₂, which greatly increased the adsorbing ability of the catalyst and was in favor of photocatalytic reaction. Compared with naked TiO₂ powder the hybrid catalyst prepared in this way showed high efficiency in the photodecomposition of acridine dye.     

超临界流体干燥法制备纳米TiO2-SnO2-SiO2复合光催化剂及其光催化性能研究

半导体多相光催化法作为一种污染治理新技术越来越受到人们的重视,在所使用的半导体光催化剂中,TiO2以无毒,催化活性高,价廉,无污染等特点,成为最具有前途的绿色环保型催化剂之一[1],但其自身具有局限性,如禁带宽度大,需在近紫外光下才能激发产生电子空穴对,对太阳光的利用率仅     

A Novel Way to Prepare TiO2 and γ‐Al2O3 Supported Catalysts with Large Surface Areas

Several TiO₂ and γ‐Al₂O₃ supported catalyst systems were prepared by a novel way and characterized by X‐ray diffraction, Raman spectroscopy and BET surface area measurement. The results show: (1) all the samples, including MoO₃/TiO₂, WO₃/TiO₂, V₂O₅/TiO₂, FeSO₄/γ‐Al₂O₃, Al₂ (SO₄)₃/γ‐Al₂O₃, K₂CO₃/‐Al₂O₃ and so on, prepared by impregnating TiO₂·H₂O or pseudo‐boehmite AlO(OH) with the active components then calcining at a high temperature exhibit much larger surface areas than that of pure TiO₂ or γ‐Al₂O₃ calcined at the same temperature; (2) the surface area of the sample increases with the increase in the coverage of active component on the surface of the support; (3) when the content of active component reaches its utmost monolayer dispersion capacity, the surface area of the sample is the largest, and then decreases when the content of active component exceeds its dispersion threshold.     

Photocatalytic Activity of High Aspect Ratio TiO2 Nanorods

In this article, TiO₂ nanorods (aspect ratio >20) were prepared through a polyol process and doped with metal ions (Cu²⁺, Ni²⁺, Fe³⁺, and Cr³⁺). Compared with TiO₂ nanoparticles, the TiO₂ nanorods displayed relatively higher photocatalytic activity for the degradation of copper sulfophthalocyanine. Moreover, the photocatalytic activity was greatly enhanced when the metal ions were doped in the TiO₂ nanorods.     

Sol–gel preparation and photocatalytic performance of TiO2/SrAl2O4: Eu2+, Dy3+ toward the oxidation of gaseous benzene

It has been found that the photocatalytic activity of TiO₂ toward the decomposition of gaseous benzene can be greatly enhanced by loading TiO₂ on the surface of SrAl₂O₄: Eu²⁺, Dy³⁺ using sol–gel technology. The prepared photocatalyst was characterized by BET, XRD, and XPS analyses. XRD results reveal that the peaks of titania in either rutile or anatase form are not detected by XRD in the 2θ region from 20° to 50°. The binding energy values of Ti 2p of pure TiO₂ are 458.90 and 464.60 eV, while for TiO₂/SrAl₂O₄: Eu²⁺, Dy³⁺, the binding energy values of Ti 2p are 458.50 and 464.20 eV. The results indicate that the optimum loading of TiO₂ is 1 wt% and TiO₂/SrAl₂O₄: Eu²⁺, Dy³⁺ (1 wt%) demonstrates 1.4 times the photocatalytic activity of that of pure TiO₂, but the underlying mechanism of SrAl₂O₄: Eu²⁺, Dy³⁺ in the photocatalytic reaction remains to be unraveled.     

Visible Light Photocatalytic Activity of Pt/N‐TiO2 towards Enhanced H2 Production from Water Splitting

Present work mainly focuses on experimental investigation to improvement of hydrogen production by water photoelectrolysis. An experimental facility was designed and constructed for visible light photocatalysis. A series of N‐TiO₂ photocatalysts impregnated with platinum on the surface of N‐TiO₂ were prepared. Hydrogen production upon irradiating aqueous Pt/N‐TiO₂ suspension with visible light was investigated. The shift in excitation wavelength of TiO₂ was 380 nm improved the yield of hydrogen production by N‐TiO₂ and Pt/N‐TiO₂. We used a 400 W mercury arc lamp combined with a 400 nm cutoff filter eliminating all the wavelengths under 400 nm. Pt/N‐TiO₂ material was characterized with TPR, reflective UV/Visible spectroscopy and TEM. The best hydrogen production rate obtained for this setup for N/Ti = 10, 0.05 wt% Pt/N‐TiO₂, through water splitting was about 772 μmolh^?1g^?1.     

柔性透明导电基底上二氧化钛自组装薄膜的制备及光电化学性能

通过层层自组装技术, 以结晶的二氧化钛为原料, 在不使用聚电解质的情况下, 免除了高温煅烧, 直接在柔性透明导电基底上制备了全纳米二氧化钛颗粒自组装薄膜。二氧化钛源主要包括带有异种电荷的锐钛矿二氧化钛溶胶和Degussa的P25二氧化钛, 溶胶中的超细二氧化钛纳米晶在制备过程中起到了调节薄膜微观结构的作用, 提高了薄膜的均匀性和致密度。将二氧化钛自组装薄膜作为工作电极, 在三电极体系中进行光电化学测试, 表面均匀致密的二氧化钛薄膜电极表现出了更高的光电化学性能, 加入溶胶后获得的自组装薄膜电极所得到的光电流强度较由全P25组装的薄膜电极提高了近25%。     

Enhanced photocatalytic degradation of rhodamine B under visible light irradiation on mesoporous anatase TiO2 microspheres by codoping with W and N

Mesoporous anatase TiO₂ microspheres were prepared via solvothermal method. Ammonium tungstate was used as the W source, and ammonia gas flowing in an ammonothermal reactor as the N source for codoping. TiO₂:(W,N) mesoporous microspheres, which were prepared from solvothermal treatment at 160 °C for 16 h and thermal ammonolysis at 500 °C for 2 h after calcination, have high specific surface area of 106 m² g⁻¹. XPS results indicate the presence of N_O, N_i and W⁶⁺ in the codoped mesoporous TiO₂ microspheres. Monodoping with N shifts the absorption band edge of anatase TiO₂ from ultraviolet region to visible region. Although codoping with W makes the visible light absorbance decrease a little, the photocatalytic degradation of a cationic dye rhodamine B (RhB) on mesoporous TiO₂:(W,N) microspheres is increased to 1.7 times of that on mesoporous TiO₂:N microspheres. This may due to decreasing recombination centers by W-doping charge compensation.     

Rutile TiO2 Submicroboxes with Superior Lithium Storage Properties

Hollow structures of rutile TiO₂, and especially with non‐spherical shape, have rarely been reported. Herein, high‐quality rutile TiO₂ submicroboxes have been synthesized by a facile templating method using Fe₂O₃ submicrocubes as removable templates. Compared to other rutile TiO₂ nanomaterials, the as‐prepared rutile TiO₂ submicroboxes manifest superior lithium storage properties in terms of high specific capacity, long‐term cycling stability, and excellent rate capability.     

Si掺杂TiO2纤维的溶胶-凝胶法制备及其光催化活性

采用溶胶-凝胶法并结合水蒸气活化制备了Si掺杂TiO₂纤维, 通过TG-DSC, XRD, FT-IR, UV-Vis-DRS, N₂吸附-脱附, SEM等手段对纤维样品的结构参数及其表面形貌进行了表征, 并以活性艳红X-3B模拟废水体系评价了其光催化活性．结果表明, 与纯TiO₂产物相比, 适量Si掺杂制得的产物是具有丰富介孔结构的TiO₂长纤维, 不仅热稳定性和晶型稳定性俱佳, 而且光催化活性得以显著提高, 经900 ℃热处理后仍能保持结晶完好的锐钛矿相; 在Si/Ti摩尔比为0.15时, 其比表面积和孔容最大, 光催化活性最佳, 该纤维作为光催化剂反应75 min, 水中X-3B的降解率可达99.6%.