谱有限元数值分析各向异性复合板中导波色散特性

提出谱有限元方法研究层状各向异性复合板中导波的色散特性和波结构。基于三维弹性动力学方程,用有限元方法离散波导截面,波传播方向的位移用简谐波表示,得到了导波色散的特征方程。分析了单层和双层复合板中导波沿不同方向传播的色散特性和波结构,讨论了双层复合板中层厚比对相速度的影响。数值研究结果表明:导波的对称模态沿纤维方向传播时在较宽的频率范围内保持弱色散状态。双层复合板中导波基本模态的相速度在低频时受层厚比的影响较明显,随着频率的增加趋向于相速度较低的材料。数值模拟结果为导波用于复合材料定量无损检测和性能评价提供理论依据。     

Calculation of leaky Lamb waves with a semi-analytical finite element method

A semi-analytical finite element method (SAFE) has been widely used for calculating dispersion curves and mode shapes of guided waves as well as transient waves in a bar like structures. Although guided wave inspection is often conducted for water-loaded plates and pipes, most of the SAFE techniques have not been extended to a plate with leaky media. This study describes leaky Lamb wave calculation with the SAFE. We formulated a new solution using a feature that a single Lamb wave mode generates a harmonic plane wave in leaky media. Dispersion curves obtained with the SAFE agreed well with the previous theoretical studies, which represents that the SAFE calculation was conducted with sufficient accuracy. Moreover, we discussed dispersion curves, attenuation curves, and displacement distributions for total transmission modes and leaky plate modes in a single side and both two side water-loaded plate.     

Diffraction of guided waves by the end face of a dielectric slab waveguide terminated with a finite conductive strip

The diffraction of guided waves by the end face of a dielectric slab waveguide short circuited with a finite conductive strip is analyzed. An integral equation technique is employed to formulate the corresponding boundary problem. The unknown term in this integral equations is the electric field E(x) on the terminal plane of the waveguide. The homogeneous term is determined from the incident guided wave. A method of moments technique is employed to compute approximately the electric field E(x) by using Laguerre functions as describing and testing functions. The reflection coefficients of the guided waves are computed by using the approximate expression of the E(x) field. Numerical results are given for several guide and conductor plate dimensions.     

Reflection and transmission coefficients for guided waves reflected by defects in viscoelastic material plates

The paper presents a Fourier transform-based signal processing procedure for quantifying the reflection and transmission coefficients and mode conversion of guided waves diffracted by defects in plates made of viscoelastic materials. The case of the S(0) Lamb wave mode incident on a notch in a Perspex plate is considered. The procedure is applied to numerical data produced by a finite element code that simulates the propagation of attenuated guided modes and their diffraction by the notch, including mode conversion. Its validity and precision are checked by the way of the energy balance computation and by comparison with results obtained using an orthogonality relation-based processing method.     

Propagation properties of elastic waves in semi-infinite phononic crystals and related waveguides

The transmission and reflection coefficients of two-dimensional semi-infinite solid-solid phononic crystal systems and fluid-fluid phononic waveguide structures have been investigated. The numerical results show that the transmission spectra for longitudinally and transversally polarized incident waves are different, and the spectra of the transmission and reflection coefficients of the semi-infinite system agree well with the band structure. The numerical results show that when a guided wave incident, localized modes are excited, and different polarities have different coupling efficiencies with the incident guided wave. At the same time, far from the cutoff frequency, the guided wave couples out of semi-infinite waveguide highly efficiently.     

谱有限元模拟正交各向异性黏弹性材料中导波传播特性

研究了导波在正交各向异性黏弹性复合板中传播的色散特性、波结构及功率流密度。基于二维平面运动方程,采用谱有限元方法得到了导波色散的特征方程。分析了正交各向异性黏弹性板中各向异性和黏性对能量速度和波结构的影响,以及基底对导波功率流密度的影响。数值研究结果表明:导波沿纤维方向传播的能量速度大,材料的黏性对速度影响较小,但会减小波结构的幅度;在高频时,基底的存在使两个基本模态的功率流密度分别集中到波导的上下表面,形成弱色散、高衰减及无色散、零衰减的表面波。数值模拟结果为导波用于复合材料定量无损检测和性能评价提供理论依据。      

Higher harmonic generation in nonlinear waveguides of arbitrary cross-section

This article concerns the generation and properties of double harmonics in nonlinear isotropic waveguides of complex cross-section. Analytical solutions of nonlinear Rayleigh-Lamb waves and rod waves have been known for some time. These solutions explain the phenomenon of cumulative double harmonic generation of guided waves. These solutions, however, are only applicable to simple geometries. This paper combines the general approach of the analytical solutions with semi-analytical finite element models to generalize the method to more complex geometries, specifically waveguides with arbitrary cross-sections. Supporting comparisons with analytical solutions are presented for simple cases. This is followed by the study of the case of a rail track. One reason for studying nonlinear guided waves in rails is the potential measurement of thermal stresses in welded rail.     

矩形波导中宽带非对称声传输

目前已有的非对称性声传输模型大部分局限于二维模式,无法直接应用于三维实际系统,针对这一问题,文中研究了通过内置非对称几何结构来实现声单向传输的三维管道模型。该几何结构体内引入天然材料——氙气,利用氙气与空气两种天然气体折射率的差异以及结构的不对称,实现声波在管道中的非对称传输,即当声波正向入射时,可通过管道内结构到达另一侧;而当反向入射时,声波无法通过内置的非对称结构。理论计算结果和仿真结果表明声波在三维矩形波导管中的非对称声传输效果和结构的厚度相关:当结构厚度较薄时,可在较宽频带范围内实现声波的非对称传输。此外,该矩形波导设计具有结构简单、透明超轻等特点,为设计新型声波非对称传输器件提供了相应的理论参考。     

介质光栅导模共振耦合波分析

导模共振是由于光栅介质内高级次子波耦合进光栅所支持的泄漏模中,导致传播波能量重新分布的结果.采用严格的耦合波方法,通过分析波导的导波模式,正确估计出弱调制介质光栅导模共振的位置.并对导模共振与光栅厚度、基底厚度以及入射角的关系作了讨论.通过采用抗反射设计,获得了具有对称、低旁带特点的窄带共振峰 关键词： 导模共振 耦合波     

Wave reflection and transmission due to defects in infinite structural waveguides at high frequencies

In waveguide structures, waves may be partially reflected by local non-uniformities such as cracks and other defects. The reflection and transmission characteristics associated with the presence of a discontinuity may be used, in principle, to give some indication of both the location and size of the defect. A combined spectral element and finite element (SE/FE) method has been used previously to investigate the effects of local non-uniformities at relatively low frequencies. However, for analysis at higher frequencies, where complex deformation of the waveguide occurs, it is necessary to extend this approach. Such high frequency analysis is necessary if small defects are to be located within the waveguide cross-section. In order to investigate wave propagation at higher frequencies, a combined spectral super element and finite element (SSE/FE) method is presented. This method allows the transmission, reflection and wave conversion at discontinuities to be determined for complex waveguides. As an example of the use of this method, wave reflection and transmission in rails are estimated at frequencies between 20 and 40 kHz for various notional sawcut-like defects of progressively increasing size. This shows the feasibility of the approach for realistic waveguides. However, from these simulations it is shown that defects have to be quite large before they can be detected using a single transducer position on the rail cross-section using train-induced vibration.     

Coupled THz Waveguide Utilizing Surface Plasmon Polaritons on Thin Dielectric Slab Sandwiched between Two Corrugated Metallic Claddings

We present a comprehensive experimental study of terahertz （THz） wave propagation utilizing surface plasmon polaritons （SPPs） on the interfaces of a thin dielectric core layer sandwiched between two corrugated metallic claddings. THz wave impinges on the structured surfaces at normal incidence. Long-lasting oscillation propagation features are observed in the temporal waveform after traveling through the periodic arrays. The enhanced THz transmission can be achieved due to the coupling between incident waves to SPPs at the bottom and top interfaces. The finite element method is used to simulate the field distribution and the transmission mode in the waveguide. The hybrid waveguide with low absorption has great potential applications in THz integrated devices.     

Characteristics analysis of hybrid plasmonic waveguide for low-loss lightwave guiding

It has been experimentally demonstrated that a low-loss guided hybrid mode is supported if a metal strip is embedded in a low index polymer layer surrounded by two high index slabs. In this paper, further numerical analyses on the guided hybrid modes are reported to fully elucidate the characteristics of the hybrid plasmonic waveguide. For a one-dimensional slab structure with a metal film of infinite width, simulation results exhibit that low-loss guided hybrid modes are associated with surface plasmon modes and dual dielectric slab modes. The optical properties of the guided modes are improved by increasing the field intensity which is confined into lossless dielectric layers by decreasing the metal film thickness and increasing the refractive index and thickness of the high-index slabs. The finite element method is used to investigate the lateral mode confinement of the optical guided modes by the corresponding metal strip. By reducing the metal film width, the guided modes are confined in the plane transverse to the direction of propagation and the characteristics are significantly improved. The hybrid plasmonic waveguide can be exploited for long-range propagation-based application such as optical interconnection.     

Guided wave dispersion curves for a bar with an arbitrary cross-section,a rod and rail example

Theoretical and experimental issues of acquiring dispersion curves for bars of arbitrary cross-section are discussed. Since a guided wave can propagate over long distances in a structure, guided waves have great potential for being applied to the rapid non-destructive evaluation of large structures such as rails in the railroad industry. Such fundamental data as phase velocity, group velocity, and wave structure for each guided wave mode is presented for structures with complicated cross-sectional geometries as rail. Phase velocity and group velocity dispersion curves are obtained for bars with an arbitrary cross-section using a semi-analytical finite element method. Since a large number of propagating modes with close phase velocities exist, dispersion curves consisting of only dominant modes are obtained by calculating the displacement at a received point for each mode. These theoretical dispersion curves agree in characteristic parts with the experimental dispersion curves obtained by a two-dimensional Fourier transform technique.     

二维光子晶体波导与单模平面介质波导间的喇叭波导接头

提出并优化了用于二维介质柱光子晶体波导与单模平面介质波导对接的基于分布布拉格反射波导的喇叭波导接头，提高了这两种波导之间的传输效率.二维时域有限差分仿真结果表明，在大部分光子晶体波导导模的频谱范围内，传输效率高于98％.传输效率最高可以达到99.85％. 关键词： 光子晶体波导 平面介质波导 时域有限差分     

Spectral and modal formulations for the Doppler-shifted field scattered by an object moving in a stratified medium

Spectral and normal mode formulations for the three-dimensional field scattered by an object moving in a stratified medium are derived using full-field wave theory. The derivations are based on Green's theorem for the time-domain scalar wave equation and account for Doppler effects induced by target motion as well as source and receiver motion. The formulations are valid when multiple scattering between the object and waveguide boundaries can be neglected, and the scattered field can be expressed as a linear function of the object's plane wave scattering function. The advantage of the spectral formulation is that it incorporates the entire wave number spectrum, including evanescent waves, and therefore can potentially be used at much closer ranges to the target than the modal formulation. The normal mode formulation is more computationally efficient but is limited to longer ranges. For a monochromatic source that excites N incident modes in the waveguide, there will be roughly N2 distinct harmonic components in the scattered field. The Doppler shifts in the scattered field are highly dependent upon the waveguide environment, target shape, and measurement geometry. The Doppler effects are illustrated through a number of canonical examples.     

Second-order bragg interaction in double grating couplers: TM mode

An analytical treatment of the second-order Bragg interaction is presented for the transverse magnetic mode of a dielectric film waveguide having gratings on both the film-cover and the film-substrate interfaces. Four canonical equations that describe the interactions of two guided waves propagating in the opposite directions in the film and the normally incident and radiated free waves in the cover and the substrate are deduced.     

A numerical approach for the computation of dispersion relations for plate structures using the Scaled Boundary Finite Element Method

In this paper, a method is presented for the numerical computation of dispersion properties and mode shapes of guided waves in plate structures. The formulation is based on the Scaled Boundary Finite Element Method. The through-thickness direction of the plate is discretized in the finite element sense, while the direction of propagation is described analytically. This leads to a standard eigenvalue problem for the calculation of wave numbers. The proposed method is not limited to homogeneous plates. Multi-layered composites as well as structures with continuously varying material parameters in the direction of thickness can be modeled without essential changes in the formulation. Higher-order elements have been employed for the finite element discretization, leading to excellent convergence for complex structures. It is shown by numerical examples that this method provides highly accurate results with a small number of nodes while avoiding numerical problems and instabilities.     

单轴各向异性异向介质平板波导中的导模特性

 推导了介电常数张量和磁导率张量中各分量带有不同符号的单轴各向异性异向介质平板波导的导行条件。根据分量符号的正负组合,分情况讨论了导行TE波的偶模特性,画出了平板波导中为实横波数时的布里渊图。结果表明,在特定条件下此平板波导中有无穷多导模,这与传统介质波导及各向同性异向介质平板中只有有限数量模式存在有很大不同。此外,还发现当分量参数满足一定条件时,出现了多个虚横波数的传输模式解,并且该模式存在高频截止。     

The scattering of guided waves in partly embedded cylindrical structures

The scattering of ultrasonic guided waves at a point where a free cylindrical waveguide enters an embedding material is investigated. A modal solution that is valid when the guided waves are incident from the free section of the waveguide is developed. It is shown that in this case it is valid to consider only the modal fields over the cross section of the waveguide, neglecting the fields in the embedding material. As an application, the scattering of the lowest-order longitudinal mode in a cylindrical waveguide, L(0,1), is examined in detail. As well as considering epoxy resin as an embedding material, the case where the embedding material is replaced by a perfectly rigid boundary is discussed. The latter gives some insight into the role of nonpropagating and inhomogeneous waveguide modes in the scattering process. The results from the modal solution are validated using Finite Element modeling, very good agreement being obtained.     

基于Rayleigh-Bloch模式的单层结构弯曲声波导

基于一维声栅中的Rayleigh-Bloch(RB)模式基本特点,设计了一种单层结构弯曲声波导.利用有限元方法从时域和频域两方面验证了弯曲声波导的有效性,RB模式波可以沿着波导的弯曲界面传播.研究发现,由于采用了环形结构基本单元,在该波导中存在两种传播模式,分别对应能量局域在单元间(模式-1)和单元内部(模式-2)两种情况.其中,模式-2声传输效果更佳,几乎可实现无损传输.时域研究中分别采用了调制脉冲和高斯脉冲两种信号形式,分析了它们在弯曲声波导中的传输过程.由于波导中只允许RB模式波传播,因此对于宽频信号来说,可起到滤波的效果.并且,不同模式(频率)的信号会出现在声波导的不同位置,所得结果对于声波定向传输、声探测与识别等研究具有理论与应用价值.