Ion-pair chromatography of polythionates and thiosulfate with detection based on their catalytic effects on the postcolumn azide–iodine reaction

The reduction of iodine with azide, catalyzed by polythionates (tri-, tetra-, penta- and hexathionate) and thiosulfate, has been utilized as a postcolumn reaction for chromatographic determination of these sulfur oxyanions. The method is based on the separation of polythionates and thiosulfate on an octadecylsilica column with an acetonitrile–water (20:80, v/v) mobile phase (pH 5.0) containing 3 mM tetrapropylammonium hydroxide and 6 mM acetic acid, followed by photometric measurement of the residual iodine (as triiodide) from the catalytic postcolumn azide–iodine reaction after mixing a reaction solution containing azide and iodine with the column effluent. Chromatograms obtained for the sulfur oxyanions showed negative peaks as a result of the decrease in absorbance of background. The conditions for the catalytic postcolumn reaction of the sulfur oxyanions in the column effluents were established by varying the concentrations of azide, iodine, iodide and acetic acid in the reaction solution, and varying the flow-rate, reaction temperature and length of the reaction tube. The detection limits (defined as S/N=3) were 4.3 μM for trithionate, 0.10 μM for tetrathionate, 2.7 nM for pentathionate, 5.0 nM for hexathionate and 1.1 nM for thiosulfate. When compared with earlier methods, the proposed method gave a much higher sensitivity for the determination of two polythionates (penta- and hexathionate) and thiosulfate. This method was applied successfully to the analysis of polythionates and thiosulfate added to hot-spring water samples.     

Determination of thiosulfate, thiocyanate and polythionates in a mixture by ion-pair chromatography with ultraviolet absorbance detection

A sensitive ion chromatographic method has been developed for the determination of mixtures of thiosulfate, thiocyanate and polythionates (tri-, tetra-, penta- and hexathionate). The proposed method is based on the separation of the sulfur anions on an octadecylsilica (ODS) column with an acetonitrile-water mobile phase containing tetrapropylammonium salt (TPA) as an ion-pairing reagent and the ultraviolet absorption detection of the sulfur anions. When an acetonitrile-water (20:80, v/v) solution (pH 5.0) containing 6 mM TPA was used as a mobile phase at flow-rate of 0.6 ml min(-1), the sulfur anions were resolved within 22 min. The detection limits defined at S/N=3 and 230 nm were very low for all anions, except trithionate: 30 nM for thiosulfate, 60 nM for thiocyanate, 20 nM for tetrathionate, 15 nM for pentathionate and 18 nM for hexathionate. The proposed method gave recoveries ranging from 95.0 to 105.0% when applied to the determination of polythionates added to hot spring waters.     

Detection of traces of oxidized and reduced sulfur compounds in small samples by combination of different high-performance liquid chromatography methods

Depending on the sulfur species, picomoles of different inorganic sulfur compounds can be detected and separated by HPLC in one arrangement in a sample volume less than 50 μl. The combination of fluorescence labelling of reduced inorganic sulfur compounds such as sulfide (S²⁻), sulfite(SO₃²⁻ and thiosulfate (S₂O₃²⁻) with monobromobimane followed by an extraction of elemental sulfur (S°) by chloroform treatment enables the detection of all mentioned sulfur compounds as well as sulfate (remaining aqueous phase) in the same sample. While the derivatized sulfur compounds could be detected by their fluorescence emission at 480 nm, elemental sulfur is identified by its UV absorption at 263 nm. Sulfate in the remaining aqueous phase is detected by HPLC with indirect UV detection at 254 nm. Detection ranges for the different sulfur compounds examined are as follows: sulfide (5 μM to 1.5 mM), sulfite (5 μM to 1.0 mM), thiosulfate (1 μM to 1.5 mM), elemental sulfur (2 μM to 32 mM) and sulfate (5 μM to >1 mM).     

Separation of polythionates and the gold thiosulfate complex in gold thiosulfate leach solutions by ion-interaction chromatography

A method for the separation of the polythionates (SxO6(2-), x = 3-5) in gold thiosulfate leach solutions using ion-interaction chromatography with conductivity and ultraviolet (UV) detection is described. Polythionates were eluted within 18 min using an eluent comprising an acetonitrile step gradient at 0.0 min from 15% v/v to 28% v/v, 3 mM TBAOH, and 2.5 mM sodium carbonate, operated using a Dionex NS1-5 micron column with guard. The developed method was capable of separating the gold thiosulfate complex ion in standard solutions, but quantification of this species in realistic leach solutions proved impractical due to a self-elution effect that caused the gold peak to be eluted as a broad band. Detection limits for polythionates using a 10 microL injection volume ranged between 1-6 mg L(-1) (5-23 microM) for conductivity and 0.8-13 mg L(-1) (4-68 microM) for UV detection, based on a signal-to-noise ratio of 2. Calibration was linear over the ranges 5-2000, 10-2000 and 25-2500 mg L(-1) for trithionate, tetrathionate and pentathionate, respectively. The technique was applied successfully to leach liquors containing 0.5 M ammonium thiosulfate, 2 M ammonia, 0.05 M copper sulfate and 20 % m/v gold ore.     

Use of short-end injection capillary packed with a glycopeptide antibiotic stationary phase in electrochromatography and capillary liquid chromatography for the enantiomeric separation of hydroxy acids

A new chiral stationary phase (CSP) was prepared by reacting MDL 63,246 (Hepta-Tyr), a glycopeptide antibiotic belonging to the teicoplanin family, with 5-μm diol-silica particles. The CSP mixed with 5-μm amino silica particles (3:1) was packed into 75-μm fused-silica capillaries for only 6.6 cm and used for electrochromatographic experiments analyzing several hydroxy acid enantiomers. A reversed electroosmotic flow carried both analytes and mobile phase towards the anode in a short time (1–3 min), being baseline resolved all the studied analytes. In order to achieve the fastest enantiomeric resolution of the studied hydroxy acids, the effect of several experimental parameters such as mobile phase composition (organic modifier type and concentration, pH of the buffer and ionic strength), capillary temperature and applied voltage on enantioresolution factor, retention time, enantioselectivity were evaluated. The packed capillary column allowed the separation of mandelic acid enantiomers in less than 72 s with resolution factor R_s=2.18 applying a voltage of 30 kV and eluting with a mobile phase composed by 50 mM ammonium acetate (pH 6)–water–acetonitrile (1:4:5, v/v). The CSP was also tested in the capillary liquid chromatography mode resolving all the studied enantiomers applying 12 bar pressure to the mobile phase [50 mM ammonium acetate (pH 6)–water–methanol–acetonitrile, 1:4:2:3, v/v)], however, relatively long analysis times were observed (12–20 min).     

Cerimetric determination of dithionate and polythionates

Ceric sulphate in a boiling strongly acidic medium oxidizes dithionate as well as tri- and tetrathionates quantitatively to sulphate. These anions may therefore be determined cerimetrically when they are present singly. A combination of the cerimetric method with other known methods (e.g. those of Kurtenacker, etc) is suggested for the analysis of mixtures of polythionates and dithionate.     

Determination of vitamin B12 in multivitamin tablets by multimode high-performance liquid chromatography

Quantitative determination of vitamin B₁₂ in B-complex tablets was performed by using multimode high-performance liquid chromatography. The multivitamin tablets (B₁, B₆ and B₁₂) were sonicated for 30 min in methanol–water (50:50, v/v) and diluted to appropriated volume with the same solvent. The resulting solution was filtered and the filtrate was analysed on a phenylpropanolamine bonded silica column (15 cm×4.6 mm I.D., 5 μm). The optimized mobile phase was 30 mM phosphate buffer (pH 3.00) containing 6% (v/v) acetonitrile at a flow-rate of 1 ml min⁻¹ and the detection was measured at 361 nm. The calibration graph prepared using standards was linear from 0.05 to 0.25 μg. The determination limit was 25 ng, the relative standard deviation was 0.47% and recovery from tablet solution was 100%. An analysis was completed in 5 min. The new method is simple, rapid and precise.     

Stabilization of sulfide and sulfite and ion-pair chromatography of mixtures of sulfide, sulfite, sulfate and thiosulfate

Ion chromatography of sulfide, sulfite, sulfate and thiosulfate in a mixture is often difficult because of instability of sulfide and sulfite, poor separation of sulfide from common anions such as bromide or nitrate and similar elution-times for sulfite and sulfate. An ion-pair chromatographic method for the determination of these sulfur anions has been established by stoichiometric conversion of sulfide and sulfite into stable thiocyanate and sulfate, respectively, prior to the chromatographic run. Sulfate, thiosulfate and thiocyanate were resolved on an octadecylsilica column with an acetonitrile-water mobile phase containing tetrapropylammonium salt (TPA) as an ion-paring reagent, and thiosulfate and thiocyanate in the effluent could be measured with a photometric detector (220 nm) and sulfate with a suppressed conductivity detector. When an acetonitrile-water (6:94, v/v) mobile phase (pH 5.0) containing 15 mM TPA and small amounts of acetic acid was used at a flow-rate of 0.6 ml min(-1), the three anions could be eluted within 32 min. Calibration plots of peak height versus concentration for sulfide (detected as thiocyanate) and thiosulfate gave straight lines up to 35 and 60 microM, respectively. The calibration plot for sulfide coincided with that obtained by using thiocyanate. A calibration plot for sulfite, measured as sulfate, was also linear up to 135 microM and was in accord with that of sulfate. Each calibration plot gave a correlation coefficient greater than 0.999. For six replicates obtained for a mixture of 30.0 microM sulfide, 50.0 microM sulfite, 50.0 microM sulfate and 20.0 microM thiosulfate, the proposed method gave a mean value of 30.1 microM with a standard deviation (SD) of 0.77 microM and a relative standard deviation (RSD) of 2.6% for sulfide, 101 microM (SD = 3.5 microM, RSD = 3.5%) for the total of sulfite and sulfate and 20.1 microM (SD = 0.44 microM, RSD = 2.2%) for thiosulfate. Recoveries for sulfide, sulfite plus sulfate, and thiosulfate in hot-spring water samples using the proposed method were found to be quantitative.     

Simultaneous determination of sulfaquinoxaline, sulfamethazine and pyrimethamine by liquid chromatography

A liquid chromatography method is described to determine sulfaquinoxaline (SQX), sulfamethazine (SMT), and pyrimethamine (PMT), by using a Kromasil C₁₈ column and a 40 mM NaH₂PO₄ buffer solution, containing 10 mM NaClO₄ (pH 3.0)–acetonitrile (65:35) as mobile phase. The mobile phase flow-rate and sample volume injected were 1.5 ml/min and 20 μl, respectively and the samples were dissolved in the mobile phase. The limits of quantification were found to be about 180 μg/l (3.6 ng) for each compound. The method was applied in veterinary commercial formulations. Analyses were made by means of the standard addition method, whose results were compared with those obtained by preparing “tests” (from the stock solutions) and with those obtained by a capillary electrophoresis method. Both methods showed similar results, and then it was proved that some commercial claimed levels were not in agreement with the obtained results by using our analytical method, as they were in other cases.     

Comparison of high-performance liquid chromatography and capillary electrophoresis for the determination of some bee venom components

HPLC and capillary electrophoretic (CE) methods were compared for the determination of phospholipase A₂ and melittin in bee venom. Size-exclusion chromatography on a Tessek Separon HEMA-BIO 40 column requires the use of a denaturing eluent (0.2% trifluoroacetic acid in 20% acetonitrile) to overcome non-specific interactions of some components, e.g., melittin. Reversed-phase HPLC on a HEMA-BIO 1000 C₁₈ column with gradient elution using water-acetonitrile mobile phases containing trifluoroacetic acid and UV spectrophotometric detection at 215 nm permits the identification and determination of the main bee venom components and their preparative chromatography. CE analysis for bee venom components is optimum with electrolyte system of 150 mM phosphoric acid (pH 1.8) with UV spectrophotometric detection at 190 nm. In comparison with HPLC, the CE method is cheaper and faster (6 min vs. 45 min) and the separation is more efficient.     

Determination of Lovastatin (mevinolin) and mevinolinic acid in fermentation liquids

A rapid and simple HPLC method for the determination of Lovastatin (mevinolin) and mevinolinic acid in fermentation fluids of Aspergillus terreus using a Separon SGX C₁₈ column and methanol-18 mM orthophosphoric acid (77.5:22.5, v/v) as mobile phase with detection at 238 nm is described. The detection limit of Lovastatin and mevinolinic acid was 20–30 ng/ml.     

Determination of niobium(V) and tantalum(V) as 4-(2-pyridylazo)resorcinol–citrate ternary complexes in geological materials by ion-interaction reversed-phase high-performance liquid chromatography

A method for the simultaneous separation and determination of Nb(V) and Ta(V) as ternary complexes formed with 4-(2-pyridylazo)resorcinol (PAR) and citrate was developed using ion-interaction reversed-phase high-performance liquid chromatography on a C₁₈ column. Method parameters, such as pre-column complex formation conditions and composition of the complexes were investigated using spectrophotometry and HPLC. Under the optimum conditions, the Nb(V) and Ta(V) complexes were eluted within 12 min with a mobile phase of methanol–water (32:68, v/v) containing 5 mM acetate, 5 mM TBABr and 5 mM citrate buffer at pH 6.5, with detection at 540 nm. A typical separation efficiency was 33 000 and 20 000 theoretical plates per metre for Nb(V) and Ta(V), respectively. The relative standard deviation of retention times for the Nb(V) and Ta(V) complexes were 0.16% and 0.17% and for peak areas were 0.28% and 1.36%, respectively. The detection limits (signal-to-noise ratio=3) for Nb(V) and Ta(V) were 0.4 ppb and 1.4 ppb, respectively. Results obtained for standard reference rock samples agreed well with certified values and results obtained by inductively coupled plasma MS.     

Colominic acid: a novel chiral selector for capillary electrophoresis of basic drugs

Capillary zone electrophoresis was used for characterising nine samples of natural organic matter (NOM) using phosphate buffer (25 mM, pH 7) and various modifiers; methanol (50 mM), acetonitrile (10%,v/v), dimethyl sulfoxide (5%,v/v), and urea (5 M). Principal component analysis (PCA) was used to examine whether the electrophoretic profiles can be utilised as fingerprints for tracing the NOM samples to their source and/or type of location. It was found that all modifiers except methanol affect the electropherograms. Furthermore, it was found that the PCA analysis carried out on the electrophoretic profiles recorded in buffer solution modified by urea gave the best results for fingerprinting. The distribution of the fingerprints suggests a model for the humic substances in which all samples can be regarded as mixtures between two endmembers: autochtonous and allocthoneous NOM.     

Determination of fenpyroximate in apples by supercritical fluid extraction and packed capillary liquid chromatography with UV detection

A method using off-line supercritical fluid extraction (SFE) and micro liquid chromatography (μLC) with UV detection at 260 nm, was developed for selective determination of fenpyroximate in apple samples. The packed capillary liquid chromatography method utilises 20 μl injection volumes with on-column focusing. A 350×0.32 mm capillary column packed with Kromasil 100-C₁₈ of 5 μm particle size was used with a mobile phase of acetonitrile–10 mM ammonium acetate (85:15, v/v) at a flow of 5 μl/min. A two-step SFE procedure was used to extract fenpyroximate selectively in 2 g apple samples, with Hydromatrix (HMX) added as a water absorbent at a 1:1 (w:w) ratio. Fenpyroximate was extracted at 200 bar and 90°C for 15 min using carbon dioxide at a flow of 2 ml/min, and solvent trapping collection in 10 ml acetonitrile. The volume of the acetonitrile extract was reduced by evaporation and water was added to a final composition of acetonitrile–water (40:60, v/v). The resulting 2.0 ml solution was filtered using a 0.45 μm poly(vinylidene difluoride) syringe filter before μLC analysis. Validation of the method was accomplished with apple samples spiked with fenpyroximate, covering the range of 0.1 to 1.0 μg/kg. The within-day and between-day repeatabilities were in the range 4–18% relative standard deviation. Accuracy, measured as recovery, was found to be approximately 60%. Apple samples from a field treated with fenpyroximate were analysed. None of the samples contained fenpyroximate above the quantification level.     

Capillary electrophoretic separation of inorganic sulfur-sulfide, polysulfides, and sulfur-oxygen species

A CE protocol was developed for the identification and separation of inorganic polysulfides simultaneously with other inorganic sulfur-bearing species coexisting in aqueous hydrosulfide/sulfur solutions. The electrophoretic separation of thiosulfate, sulfate, hydrosulfide, sulfite, tetrathionate, and polysulfides was achieved at pH values between 8.2 and 12.2. The peaks attributed to the polysulfide species were strongly sensitive to pH. CE analysis of hydrosulfide/sulfur solutions at different pH values permitted possible identification of two forms of polysulfides: S4(2-) and S3(2-). Upon exposure to air at ambient temperature, thiosulfate was the main oxidation product of hydrosulfide/sulfur solutions mainly in the first 60 min, when hydrosulfide was rapidly consumed. Analysis of the oxidation reaction products provided retrospectively tentative evidence that the peaks separated and identified as tri- and tetrasulfide may be ascribed to polysulfides.     

High-performance liquid chromatographic-electrospray mass spectrometric analysis of phenolic acids and aldehydes

The present work describes the development of an HPLC-electrospray mass spectrometric method for the analysis of phenolic acids and aldehydes. These compounds are important for the quality of foods and feeds, such as dietary fiber supplements, wine and lignicellulose by-products. Good separation was obtained with a phenyl column (3 μm particle size, 150 mm×3.9 mm I.D.), using McOH-H₂O (30:70, v/v) as the mobile phase with 0.01% CH,COOH and 0.2 mM tetraethyl ammonium iodide as the ion pairing agent, at a flow-rate of 0.3 ml/min. This system permits post column splitting of the eluate for analysis by electrospray mass spectrometry with a flow-rate of 11 μl/min. This new method is extremely sensitive and less than 6 pg/inj of the studied phenols can be identified and quantified. This method was applied to standard compounds as well as to components of high-fiber dietary supplements (primarily wheat bran), cornmeal, and oat bran.     

Separation and detection of common mono- and divalent cations by ion chromatography with an ODS column and conductivity/UV detection

The retention and detection behavior of common mono- and divalent cations (M⁺, alkali metal (Li⁺, Na⁺, K⁺, Rb⁺, Cs⁺) and ammonium ions (NH₄⁺); M²⁺, alkaline earth metal ions (Mg²⁺, Ca²⁺, Sr²⁺, Ba²⁺) was examined using an ODS column (150×4.6 mm I.D.) and conductivity (CD)/UV detection. The results obtained were as follows: (1) for M⁺, the mobile phase, 0.1 mM sodium dodecyl sulphate (SDS)+10 mM HNO₃ and indirect CD detection were effective. (2) Addition of Ce(III) in the mobile phase accelerated the elution of both M⁺ and M²⁺. The separation of above 10 cations on an ODS column was achieved for the first time without any coelution of cations and disturbance by system peak. Addition of higher SDS resulted in good separation of M⁺ and M²⁺ with longer retention times. CD detection was possible for M⁺ and M²⁺ and UV detection for M²⁺. (3) For M²⁺, the mobile phase, 0.8 mM Ce(III)+0.1 mM SDS+1 mM HNO₃ and indirect UV detection were effective. The IC methods were applied to real samples.     

Quenching and liquid chromatographic determination of polythionates in natural water

Polythionates in highly acidic, crater-lake water have been determined by ion-chromatography and high-performance microbore liquid chromatography. The first technique allows the determination of tri-, tetra- and pentathionate in excess of 10 ppm, and the second allows analysis for tetra-, penta- and hexathionate in excess of 0.2 ppm. The methods for preserving polythionates in natural solutions are also discussed. The recommended procedures for storage are to add hydroxylamine hydrochloride to sample solutions or to exclude atmospheric oxygen by using Winkler oxygen-determination bottles, followed by storage in a refrigerator at 5 degrees .     

On-line concentration of s-triazine herbicides in micellar electrokinetic chromatography using a cationic surfactant

A new method for the simultaneous determination of anions (sulfate, nitrate, and chloride) and cations (sodium, ammonium, potassium, magnesium, and calcium) in acid rain waters was investigated using high-performance ion-exclusion/cation-exchange chromatography with conductimetric detection on a separation column packed with a polymethacrylate-based weakly acidic cation-exchange resin in the hydrogen-form and an eluent comprising 1.5 mM sulfosalicylic acid–6 mM 18-crown-6 at pH 2.6, operated at 1.5 ml/min. Effective separation and highly sensitive conductimetric detection for the anions and the cations was achieved in about 14 min. Since the ionic balance (equivalents of anions/equivalents of cations) of acid rain waters of different pH (4.40–4.67) ranged from 0.97 to 0.94, evaluation of the water quality of acid rain was possible. This method was successfully applied to the simultaneous determination of the anions and the cations in acid rain transported from mainland China and North Korea to central Japan monitored by a meteorological satellite data analyzer.     

Determination of benzylpenicillin, oxacillin, cloxacillin, and dicloxacillin in cows' milk by ion-pair high-performance liquid chromatography after precolumn derivatization

A high-performance liquid-chromatographic method has been developed for the determination of five penicillin compounds (benzylpenicillin, phenoxymethylpenicillin, oxacillin, cloxacillin, and dicloxacillin) at trace levels in commercially available milk samples. This method comprises extraction of the lipids with ethyl acetate, clean-up and concentration on a C-18 solid-phase extraction column, and derivatization with 1,2,4-triazole and mercury(II) chloride solution, pH 8, at 65 degrees C for 10 min. The derivatized compounds are eluted from a C-2 column with a mobile phase containing acetonitrile and phosphate buffer loaded with sodium thiosulfate and tetrabutylammonium hydrogen sulfate as ion-pairing reagent. The limit of determination was found to be 4 microg L(-1) milk for benzylpenicillin and 10 microg L(-1) for the others. This meets EU criteria according to decision No. 93/256/EEC.