Comparison of three digestion methods for the determination of the aqua regia soluble content of lead,cadmium and chromium in sewage sludges by ETAAS

A procedure for the determination of the aqua regia soluble content of lead, cadmium and chromium in a sewage sludge reference material (CRM 145R) by electrothermal atomic absorption spectrometry (ETAAS) is described. A comparison of the dissolution procedure proposed in the certification report, to an oven-assisted digestion and a proposed microwave digestion procedure is performed. In the ETAAS method developed, 1 g of Pt proved to be an appropriate modifier for each of the above heavy metals. Possible sources of error at each analytical step are addressed. The metal contents obtained with the proposed method are in a good agreement at 95% significance level with the certified values given for CRM 145R.     

不同前处理方法测定银锡焊料中3种重金属元素

选用银含量为3%、30%和70%的银锡焊料样品,分别经过三种不同前处理方法,采用硝酸、盐酸消解,应用电感耦合等离子体发射光谱法(ICP-OES)同时测定锡铅合金中镉、铅、汞3种重金属元素含量。实验研究了不同前处理方法对银锡合金中重金属测定的影响。实验表明消解实验中的共沉淀现象会对3种重金属元素的测定产生不利的影响,回收率不能满足要求;采用硝酸消解,过滤残渣经王水消解的方法,镉、铅、汞的7次测定重复性相对标准偏差在2.7%~5.5%、加标回收率在85.6%~103%,能够满足RoHS测试要求。     

不同消解方式对土壤中锑的原子荧光法检测影响

氢化物发生-原子荧光光谱法是土壤环境中锑检测所广泛使用的方法．土壤的消解前处理分别采用王水微波消解（半消解）、混酸全消解（硝酸＋高氯酸＋氢氟酸）方式．研究结果表明王水微波消解对锑的检测效果较好,标准土壤9次测定值的相对标准偏差为3．6％,实际样品的回收率为96％-102％．而采用混酸全消解的方式测定值偏低,实际样品的回收率为78％～86％,而且精密度超过5％,这是由于在赶酸过程中样品易被蒸干而造成痕量锑元素的损失．     

Comparison of wet microwave digestion methods of plant materials for the determination of metals by flame atomic absorption spectrometry

Microwave closed-system wet digestion procedures for plant samples were examined. Each procedure was tested with samples of tobacco and cabbage, and included digestion by the use of different acids composition, almost complete evaporation of the digest, and then dissolution of the residue in 1% nitric acid. Three microwave digestion programs that varied power, duration, and temperature were used. Closed-vessel reactions followed open-vessel reaction-delay time. Using flame atomic absorption spectrometry on the digests, four or five elements were determined to evaluate effectiveness, precision and accuracy of analytes extraction into solution. After a preliminary study of tobacco digests, the four most effective procedures were chosen, and detailed investigations were carried out on both tobacco and cabbage reference materials. Although all four of the final procedures were accurate, the most precise procedure, with the lowest errors of determination, was using reverse ‘aqua regia’ for tobacco and ‘aqua regia’ for cabbage.     

一次消解土壤样品测定汞、砷和硒

建立了测定土壤中3种挥发性元素(汞、砷、硒)的一次消解方法,确定以程序控温石墨自动消解仪+王水-氢氟酸-硼酸络合敞开体系为最佳消解体系,采用氢化物发生-原子荧光光谱法(HG-AFS)分别测定同一消解液中汞、砷、硒的含量.采用国家标物中心有证标准物质土壤环境样品GSS-1~GSS-8进行了方法验证,结果均符合标准偏差的允许范围.此消解方法相比于现行标准方法,避免了针对各元素的分次处理,简化了消解步骤,节省了前处理时间,减少了试剂消耗,提高了实验效率,适用性广、灵敏度高、检出限低,尤其适合批量样品的微量/痕量元素分析,可作为一种大规模土壤样品中重金属污染监测和治理的快捷方法.     

原子荧光法测定土壤中砷的消解方法研究

分别用王水消解法和硫酸-硝酸-高氯酸混合酸消解法处理样品,用原子荧光光度计法测定了砷的含量,比较了两种消解方法砷的测定值和标准值.结果表明,采用混合酸消解法砷的测定值低于标准值,而采用王水消解法可以准确测定土壤中砷含量,实验操作简单方便,结果准确、可靠.     

Investigation of heavy-metal uptake by vegetables growing in contaminated soils using the modified BCR sequential extraction method

The heavy metal (Cu, Fe, Co, Ni, Cd, Cr, Pb, Zn, and Mn) concentrations in soils and in vegetable samples, i.e. lettuce (Lactuca sativa L.), parsley (Petroselinum crispum), dill (Anethum graveolens), and onion (Allium cepa L.), taken from three urban vegetable gardens in Kayseri, Turkey, were determined by FAAS. The modified three-step sequential extraction procedure proposed by the European Bureau of References (BCR), now the Standards, Measurements and Testing Programme, was used in order to evaluate trace elements mobility in soil samples, and heavy-metal uptake by vegetables. Three operationally defined fractions were isolated using the BCR procedure: acid extractable (i.e. bound to carbonates), reducible (bound to Fe/Mn oxides), and oxidizable (bound to organic matter and sulphides). The vegetable samples were prepared to analysis using the wet-ashing procedure. To estimate the accuracy of the method used in analysis of the vegetable samples, the standard reference material (NIST SRM 1573a, Tomato leaves) was used. The results of recovery for all the elements were relatively satisfactory (87.7–108%). For the soil samples, the recovery values were calculated by proportioning the sum of the steps of the BCR procedure to those of the pseudototal digestion (i.e. aqua regia). In soils, the mobility of heavy metals followed the order Mn>Cd>Cu>Pb>Zn>Cr>Ni>Co>Fe. The relationship between the vegetable–metal and soil–extractable metal concentrations was examined in order to evaluate the bioavailability of metals, and the positive correlation, especially for the first (i.e. water, acid-soluble and exchangeable fraction) and for the third (i.e. oxidizable fraction) extraction steps, was obtained.     

Trace elements in soil: Their determination and speciation

Summary The different types of soil analysis are reviewed in-outline and some recent developments and methodologies are discussed.For the determination of the total trace element content of soils, conventional, multi-element, solid sample methods including d.c. arc optical emission and spark source mass spectrometric procedures are briefly considered together with the potential of current X-ray fluorescence, solid sample graphite furnace atomic absorption and glow discharge mass spectrometry.The use of strong acid digestion, with for example aqua regia, for the determination of pseudo-total concentrations of heavy or toxic metal accumulations in soil is described.The limitations of solution methods for multi-element analysis of soils are outlined together with the prospects for the use of soil slurries to eliminate the sample preparation and dilution problems associated with the dissolution of soils. The difficulties in taking reproducible and representative samples of inhomogeneous materials such as soils are highlighted.Trace element speciation can be defined as the identification and quantification of the different forms or phases in which they occur in soils. Some examples of such procedures and extractants for both essential and toxic elements in soils are presented. The difficulties of trace element speciation in soils as distinct from soil extracts or soil solutions are illustrated briefly.     

An evaluation of the modified BCR sequential extraction procedure to assess the potential mobility of copper and zinc in MSW

Copper and zinc were determined in municipal solid waste (MSW) samples with different deposit ages from Tianziling landfill site. The pseudototal metal contents of the MSW samples were determined following an aqua regia digestion. Operational speciation was performed using the modified BCR sequential extraction procedure. Analyses were carried out by AAS. Agreement between most of triplicate samples was acceptable. The amount of copper and zinc extracted in the sequential procedure (i.e. Step 1, Step 2, Step 3, residual) did not generally agree well with pseudototal digestion. Various MSW samples contained significant different levels of copper and zinc, but these were with different potential migrations. For example, 49.88%-76.34% of copper existed in five MSW samples was present as oxidable fraction while ~ 40% of zinc was present as acid soluble fraction. The study illustrates the feasibility and importance of modified BCR sequential extraction procedure used as evaluation method when assessing the potential mobility of heavy metal in MSW landfill.     

The homogeneity of heavy metal deposition on glass fibre filters collected using a high-volume sampler in the vicinity of an opencast chrome mine complex at Kemi,Northern Finland

The homogeneity of heavy metal (Cr, Ni, Cu, Fe and Cd) distribution on glass fibre filters (Munktell MG 160, 203 x 254 mm, 75 g m(-2)) collected using a high-volume sampler (Wedding & Associates) at an opencast chrome mine complex at Kemi, Northern Finland was studied. The heavy metals in the total suspended particulate (TSP) material were analysed by inductively coupled plasma atomic emission spectrometry (ICP-AES) or graphite furnace atomic absorption spectrometry (GFAAS). The glass fibre filters were digested in a microwave oven using a mixture of aqua regia+HF acids. There was significant non-uniform distribution of heavy metals on glass fibre filters. The TSP material containing chromite was very difficult to dissolve by acid digestion. The results from X-ray fluorescence spectrometry (XRF), and from energy filtering transmission electron microscope (EFTEM) equipped with energy dispersive X-ray spectrometer (EDS), showed that insoluble residue left after microwave oven digestion with aqua regia+HF acids was probably partly due to chemical reactions occurring during microwave heating.     

Speciation of beryllium, nickel, and vanadium in soil samples from Csepel Island, Hungary

Sequential leaching methods have been used for the speciation of Be, Ni, and V in five soil samples from Csepel Island on the Danube river located near an oil-fired power plant. The concentrations of the elements of the extracts were determined by inductively coupled plasma mass spectrometry. The total efficiency (the sum of the extracted metals divided by metal fraction which is soluble in aqua regia) of the five-step method was always higher. The difference for Ni was considerable, because of the high abundance of Ni found in the moderately reducible fraction, which is absent from the three-step method. The sum of the mobile species (exchangeable, carbonatic, and easily reducible) determined by both methods, were in reasonable agreement; this was not so for the individual fractions. There were greater differences between the non-mobile fractions (moderately reducible and oxidizable), because of the presence or absence of the moderately reducible fraction. For both methods there was good correlation between the oxidizable fraction and the organic matter content of the soils.     

Speciation of beryllium, nickel, and vanadium in soil samples from Csepel Island, Hungary

Sequential leaching methods have been used for the speciation of Be, Ni, and V in five soil samples from Csepel Island on the Danube river located near an oil-fired power plant. The concentrations of the elements of the extracts were determined by inductively coupled plasma mass spectrometry. The total efficiency (the sum of the extracted metals divided by metal fraction which is soluble in aqua regia) of the five-step method was always higher. The difference for Ni was considerable, because of the high abundance of Ni found in the moderately reducible fraction, which is absent from the three-step method. The sum of the mobile species (exchangeable, carbonatic, and easily reducible) determined by both methods, were in reasonable agreement; this was not so for the individual fractions. There were greater differences between the non-mobile fractions (moderately reducible and oxidizable), because of the presence or absence of the moderately reducible fraction. For both methods there was good correlation between the oxidizable fraction and the organic matter content of the soils.     

Relationship between vegetable metal and soil-extractable metal contents by the BCR sequential extraction procedure: chemometrical interpretation of the data

The contents of heavy metals in soil and vegetable samples collected from an urban garden in Kayseri, Turkey, were investigated. Both wet- and dry-ashing methods were used for dissolving vegetable samples. A sequential extraction procedure proposed by the Commission of the European Communities, Community Bureau of Reference (now superseded by the Standards, Measurement and Testing Programme, SM&T) was applied to the soil samples to extract the metals which are present in exchangeable and acid soluble (i.e. bound to carbonates), reducible (bound to Fe/Mn oxides), and oxidisable forms (bound to organic matter and sulphides) in the soil samples. Trace metals in the soil and vegetable samples were determined using flame atomic absorption spectrometry (FAAS). The total metal contents acquired by summing of metal levels in all the sequential extraction steps were compared with pseudo-total metal levels obtained with aqua regia for all the soil samples. The recovery values obtained by proportioning the results obtained by the BCR procedure to those of the pseudo-total digestion were found to be satisfactory. The limits of detection for the elements investigated were in the range of 0.04 to 0.59?µg?mL^?1 for all the extraction stages of the BCR procedure. Similarities among the variables were identified by correlation analysis, principal component analysis and hierarchical cluster analysis. The relationship between the vegetable metal and soil-extractable metal concentrations was examined in order to evaluate the bioavailability of metals.     

Microwave-assisted aqua regia digestion for determining platinum,palladium, rhodium and lead in catalyst materials

This study investigated a microwave-assisted aqua regia digestion of catalyst samples prior to the determination of Pt, Pd, Rh and Pb by ICP-OES. While optimising the method, the effect of digestion temperature on the digestion efficiency was investigated. Few aqua regia digestions were also carried out using a high pressure asher, with a digestion temperature of 280 °C. In addition, XRD (X-ray diffractometry) was used to characterise digestion residue. The study showed that accurate and reliable results for Pt, Pd, Rh and Pb in a recycled monolith catalyst (NIST SRM 2557) were obtained by ICP-OES after the microwave assisted aqua regia digestion. The amounts of Pt, Pd and Rh in the prepared catalyst samples were also at the expected levels. Furthermore, the results indicated that the main part of the impurities and supporting material elements can be quantitatively extracted from the catalyst samples by using the microwave-assisted aqua regia sample pre-treatment.     

Sampling and digestion of waste mobile phones printed circuit boards for Cu,Pb, Ni,and Zn determination

Sampling is the most important procedure in arriving at the value of an electronic scrap. Inappropriate sampling makes other procedures, including assaying, valueless, as the sample must really represent the electronic scrap from which it was taken. The aim of this study was to develop the procedure to investigate the composition of heterogeneous printed circuit boards (PCBs) material and to show its applicability as well as its related limitations. The contents of Cu, Pb, Ni, and Zn in PCBs from wasted mobile phones were determined. Mixtures of aqua regia, hydrogen peroxide and hydrofluoric acid were applied to sample digestion. Open and closed vessel wet digestion with or without heating and microwave-assisted one was realized. For these purposes different sample amounts (0.2, 0.4, and 0.5 g) were applied and on the basis of calculated relative standard deviation values (RSD), the precision of repeated the most effective digestion was evaluated. The microwave-assisted wet digestion and mixture of aqua regia and hydrogen peroxide was found as the most effective one of the compared mixtures and applied conditions. A sample amount of 0.5 g was found as the most suitable. RSD values confirm the importance of electronic waste material sample preparation.     

Atomic absorption spectrometric determination of mercury in soil standard reference material following microwave sample pretreatment

Several decomposition procedures and their influence on the determination of mercury by electrothermal (ET) and cold vapour (CV) atomic absorption spectrometry (AAS) have been studied. Soil samples were decomposed by microwave digestion in closed and open vessels as well as by digestion under reflux according to German standard. The use of different acids (HNO₃, HCl or aqua regia) was evaluated and compared in respect to their influence on the determination of mercury by ET AAS and CV AAS. The digestion solutions were analyzed by ET AAS with a palladium modifier and by CV AAS using SnCl₂ or NaBH₄, as reducing agents. The detection limits obtained with different procedures were also evaluated. For the soil containing 6.25 g/g of Hg the ET AAS measurements were possible. In the case of lower concentration of mercury the CV AAS determination following the microwave digestion procedure with HCl or aqua regia is recommended. The accuracy of the proposed procedure was confirmed by the determination of total mercury in SRM 2711 Montana Soil.On leave from: Institut für Analytische Chemie, Technische Universitat Wien, Getreidemarkt 9, A-1060 Wien, Austria     

Extractability of HgS (cinnabar and metacinnabar) by hydrochloric acid

In this work we investigated the behaviour of pure HgS during extraction with dilute HCl to establish its extractability in 1 and 6 M HCl at the concentration level close to those occurring in natural sediments and soils. We found that neither cinnabar nor metacinnabar were soluble in 1 M HCl, whereas both were partially extracted by 6 M HCl. Metacinnabar precipitated in the laboratory was most prone to dissolution in 6 M HCl (up to 90%), followed by crystalline (commercial) metacinnabar (up to 70%) and cinnabar (up to 15%). Solubility of HgS in 6 M HCl was found to be dependent on its concentration, and an exponential relationship between quantity of HgS added to 20 mL of 6 M HCl (the range of 0.1-10 mg was used) and the solubility in 6 M HCl was established. For higher concentrations of HgS (10 mg in 20 mL of acid), a similarly low solubility of cinnabar was obtained as found in the literature. A study of dissolution kinetics of HgS in 6 M HCl indicated that it was a fairly slow process. Unexpected oxidation of HgS in water or 1 M HCl was found for extractions performed in Teflon vials previously used for the digestion of residual undissolved HgS by aqua regia. We presumed that the Teflon material could preserve some oxidising gases (presumably Cl(2)) developed during digestion with aqua regia which can then oxidise HgS during extraction with water or 1 M HCl. Regarding the extraction of Hg from natural sediments, we concluded that 6 M HCl could not be used to extract reactive Hg and predict bioavailability of mercury in sediments containing HgS and that experiments with model compounds should not be done at a concentration level several orders of magnitude higher than in natural samples.     

微波消解-电感耦合等离子体发射光谱测定铜精矿中的银

铜精矿试样利用HCl和HNO3混酸于微波消解仪中进行溶解,电感耦合等离子体发射光谱(ICP-OES)法测定铜精矿中的银含量。试验了不同比例消解体系的消解效果,研究了不同浓度铁、铜基体的影响,结果表明王水体系消解效果最佳,1 000mg/L以下的铁、铜或铁、铜的混合基体对银的测定没有影响,10%HCl体系作为测定酸度。该方法对银的线性范围为0.73~1 500g/t,标准物质测定值与标准值无显著性差异。该方法前处理试剂消耗少、速度快,分析浓度范围宽,可用于铜精矿中银的快速测定。     

Influence of sample pre-treatment on the determination of trace silver and cadmium in geological and environmental samples by quadrupole inductively coupled plasma mass spectrometry

The suitability of three different digestion procedures has been evaluated with regard to the quantitative determination of trace amounts of silver and cadmium in geological and environmental samples. Procedure A: extraction with aqua regia in an open vessel system; Procedure B: extraction with aqua regia in a closed pressurized vessel system; Procedure C: digestion with HF + HNO₃ in a closed pressurized vessel system. It was found that procedure A represented an effective way of extracting analytes from different types of geological samples while the effect of extracting interfering metals is low. Because it is interference-free, poses a low risk of contamination and is time-saving, sample treatment procedure A was preferred. For this digestion procedure, a series of Chinese geological reference materials was determined by ICP-MS, the results of which were found to be in reasonable agreement with the certified values.     

Comparison of open digestion methods and selection of internal standards for the determination of Rh,Pd and Pt in plant samples by ICP-MS

An analytical procedure for the reliable determination of Pd, Pt and Rh in plant samples by inductively coupled plasma-mass spectrometry (ICP-MS) was developed. An ultrasonic nebulizer (USN) was used for sample introduction to improve sensitivity. Under various synthetic plant sample matrix compositions, it was established experimentally that moderate amounts (0.2–2%) of dissolved solids decreased the analyte signals significantly. Internal standardisation with In (for Pd and Rh) and Ir (for Pt) proved to be essential for obtaining correct results. Five open digestion approaches, used for converting solid plant samples to aqueous solution, were also tested for the purpose, namely dry-ashing, dry-ashing followed by HF attack, wet digestion with H₂O₂–HNO₃, wet digestion followed by HF attack and aqua regia digestion. Recovery tests in two spiked plant materials showed that only wet digestions must be used. With these ways, all PGEs could be reliably quantified by USN-ICP-MS without applying a separation or preconcentration step with a good precision (below 10% RSD). The aqua regia procedure was applied to the determination of PGEs in various plant matrices collected along a highway. Results showed that mosses were probably the best choice of samples to monitor the bioaccumulation of PGEs in time.