Determination of phenylurea herbicides in aqueous samples using partitioned dispersive liquid-liquid microextraction

Partitioned dispersive liquid-liquid microextraction (PDLLME), using THF as the dispersive solvent and dichloromethane as the extraction solvent, was utilized to isolate and concentrate phenylurea herbicides (PUHs) from aqueous samples. In PDLLME, a dispersive solvent should be able to partition in the organic extractant droplets to effectively extract the polar organic compounds from aqueous samples. The mixture of the water-immiscible extractant and the partitioned dispersive solvent was obtained by centrifugation, dried under low pressure, reconstituted in methanol-water mixture (1:1), and injected into a HPLC system for the determination of PUHs. The enrichment factors of the PUHs ranged from 68 to 126 under the optimal conditions. The linear range was 0.5-100 ng ml⁻¹ for each analyte, the relative standard deviations of PUHs were in the range of 1.5-5.9% (n = 5), and the detection limits (signal-to-noise ratio of 3) ranged from 0.10 to 0.28 ng ml⁻¹ for the herbicides. The range of intraday precision (n = 5) for PUHs at the levels of 0.5, 5, and 50 ng ml⁻¹ were 3.0-5.9%, 1.8-3.3%, and 2.2-3.6%, respectively. The range of interday precision (n = 5) at 0.5, 5, and 50 ng ml⁻¹ were 0.4-1.8%, 1.2-2.4%, and 0.9-2.3%, respectively. The recoveries of PUHs from three spiked river water samples, at a level of 10 ng ml⁻¹, were 91.2-104.1%. Due to its rapidity, ease of operation, and high recovery, PDLLME can be utilized to isolate and concentrate organic environmental contaminants such as PUHs from aqueous samples.     

Bacteria detection based on the evolution of enzyme-generated volatile organic compounds: Determination of Listeria monocytogenes in milk samples

The rapid detection of Listeria monocytogenes contamination in food is essential to prevent food-borne illness in humans. The aim of this study was to differentiate non-contaminated milk from milk contaminated with L. monocytogenes using enzyme substrates coupled with the analysis of volatile organic compounds (VOCs). The method is based on the activity of β-glucosidase and hippuricase enzymes and the detection of a specific VOC i.e. 2-nitrophenol and 3-fluoroaniline, respectively. VOCs were extracted, separated and detected by headspace-solid phase microextraction coupled to gas chromatography–mass spectrometry (HS-SPME GC–MS). This approach required the inclusion of the selective agent's cycloheximide, nalidixic acid and acriflavine HCl in the growth medium to inhibit interfering bacteria. The VOCs were liberated by L. monocytogenes provided that samples contained at least 1–1.5 × 10² CFU ml⁻¹ of milk prior to overnight incubation. This approach shows potential for future development as a rapid method for the detection of L. monocytogenes contaminated milk.     

Ultra-trace level determination of hydroquinone in waste photographic solutions by UV-vis spectrophotometry

A simpler UV-vis spectrophotometric method was investigated for hydroquinone (HQ) determination using KMnO₄ as oxidizing agent for conversion of HQ to p-benzoquinone (BQ) as well as signal enhancer. Various parameters such as analytical wavelength, stability time, temperature, pH, solvent effect and interference of chemicals were checked and parameters optimized by using 1 μg ml⁻¹ standard solution of HQ. Beer's Law was applicable in the range of 0.07-2 μg ml⁻¹ and 0.005-0.05 μg ml⁻¹ at 245.5 nm and at 262 nm for aqueous standard solutions of HQ with linear regression coefficient value of 0.9978 and 0.9843 and detection limit of 0.021 μg ml⁻¹ and 0.0016 μg ml⁻¹ HQ, respectively. Standard deviation of 1.7% and 2.4% was true for 1 μg ml⁻¹ and 0.03 μg ml⁻¹ HQ solution (n = 11) run at respective wavelengths. The method was successfully applied to dilute waste photographic developer samples for free HQ determination.     

A rapid determination of propiverine and its N-oxide metabolite in human plasma by high performance liquid chromatography-electrospray ionization tandem mass spectrometry

A simple, fast and sensitive high-performance liquid chromatography (HPLC)-electrospray ionization (ESI) tandem mass spectrometric method (LC-MS/MS) has been developed for determination of propiverine and propiverine N-oxide metabolite in human plasma using oxybutynin as internal standard. Instead of extracting propiverine from plasma using organic solvents, which should be separated from the aqueous phase and evaporated before injecting the sample into the chromatograph, plasma sample containing propiverine and N-oxide was directly injected after precipitating proteins with acetonitrile. Numerous compounds in the plasma did not interfere with the highly specific multiple reaction monitoring in tandem mass spectrometric detection following C₈ reversed-phase chromatographic separation under conditions that eluted propiverine, N-oxide and oxybutynin within 2 min (0.1% formic acid in water/acetonitrile, 25:75, v/v). The LC-MS/MS method and an alternative LC-MS method, using methyl-t-butyl ether extraction and selected ion monitoring, were validated over 1-250 ng ml⁻¹ of propiverine and 2 to 500 ng ml⁻¹ of N-oxide, and successfully applied in a pharmacokinetic study. The lower limit of quantitation was 1 ng ml⁻¹ for propiverine and 2 ng ml⁻¹ for N-oxide in both methods.     

Determination of volatile organic compounds in urban and industrial air from Tarragona by thermal desorption and gas chromatography-mass spectrometry

This study describes the optimisation of an analytical method to determine 54 volatile organic compounds (VOCs) in air samples by active collection on multisorbent tubes, followed by thermal desorption and gas chromatography-mass spectrometry. Two multisorbent beds, Carbograph 1/Carboxen 1000 and Tenax/Carbograph 1TD, were tested. The latter gave better results, mainly in terms of the peaks that appeared in blank chromatograms. Temperatures, times and flow desorption were optimised. Recoveries were higher than 98.9%, except methylene dichloride, for which the recovery was 74.9%. The method's detection limits were between 0.01 and 1.25 μg m⁻³ for a volume sample of 1200 ml, and the repeatability on analysis of 100 ng of VOCs, expressed as relative standard deviation for n = 3, was lower than 4% for all compounds. Urban and industrial air samples from the Tarragona region were analysed. Benzene, toluene, ethylbenzene and xylenes (BTEX) were found to be the most abundant VOCs in urban air. Total VOCs in urban samples ranged between 18 and 307 μg m⁻³. Methylene chloride, 1,4-dichlorobenzene, chloroform and styrene were the most abundant VOCs in industrial samples, and total VOCs ranged between 19 and 85 μg m⁻³.     

Group-specific enzyme-linked immunosorbent assay for fenitrooxon and 3-methyl-4-nitrophenol in water samples based on a polyclonal antibody

Fenitrooxon [O,O-dimethyl-O-(4-nitro-m-tolyl)phosphate] is the major metabolite of the organophosphorus insecticide fenitrothion, and 3-methyl-4-nitrophenol is its major degradation product. In the present study, we describe the development of an indirect competitive enzyme-linked immunosorbent assay (ELISA) for the detection of these compounds in water samples based on a group-specific polyclonal antiserum generated with a “bifunctional hapten”, which has two functions: the conventional function of producing an antibody against an antigen and a unique function of promoting the production of the antibodies in rabbit. For application to water samples, the influence of several factors such as organic solvent, pH, and detergent was studied. Under optimized conditions, the quantitative working range of the fenitrooxon ELISA was 0.71-27 ng ml⁻¹ with a limit of detection (LOD) of 0.32 ng ml⁻¹, and the fenitrooxon concentration giving 50% reduction of the maximum signal (IC₅₀) was 4.2 ng ml⁻¹. The quantitative working range of the 3-methyl-4-nitrophenol ELISA was 0.67-27 ng ml⁻¹ with a LOD of 0.38 ng ml⁻¹ and an IC₅₀ of 3.7 ng ml⁻¹. No significant matrix effect originating from the water sample (river water, tap water, purified water, and bottled water) was shown by addition of Tween 20 to the assay buffer. Water samples spiked with each of these compounds at 1, 5, 10, and 20 ng ml⁻¹ were directly analyzed without extraction and clean-up by the proposed ELISA. The mean recovery was 100.9%, and the mean coefficient of variation (CV) was 7.7% for the fenitrooxon ELISA and for the 3-methyl-4-nitrophenol ELISA, the mean recovery was 97.6%, and the mean CV was 7.2%. The proposed ELISA allows precise and accurate determination of these compounds in water at such low levels.     

Backscattering light detection of nucleic acids with tetraphenylporphyrin-Al(III)-nucleic acids at liquid/liquid interface

A backscattering light (BSL) detection assembly is constructed and applied to the determination of nucleic acids with high sensitivity and selectivity based on the measurements of BSL signals at water/tetrachloromethane (H₂O/CCl₄) interface. In aqueous medium of pH 3, the binary complex of of Al(III)-DNAs could be formed by the interaction of Al(III) with the phosphate group of DNAs, which then could interact with tetraphenylporphyrin (TPP) in tetrachloromethane through liquid/liquid interaction, forming a ternary complex of TPP-Al(III)-DNAs at the interface. It was observed that greatly enhanced BSL signals occurred with maximum peak at 469 nm when the ternary complex of TPP-Al(III)-DNAs were absorbed to the liquid/liquid interface. The enhanced backscattering light intensity (I_BSL) is in proportion to the concentration of calf thymus DNA (ctDNA) and fish sperm DNA (fsDNA) in the range of 0.6-1200 ng ml⁻¹ and 1.1-1200 ng ml⁻¹, respectively. The limits of determination (3σ) are 60 pg ml⁻¹ and 110 pg ml⁻¹, correspondingly. Artificial samples with highly interference backgrounds were determined with the recovery ranging from 94.5 to 106.7%, and relative standard deviation (R.S.D.) less than 2.40%.     

Fluorescence and terbium-sensitised luminescence determination of garenoxacin in human urine and serum

Fluorescence and terbium-sensitised luminescence properties of new quinolone garenoxacin have been studied. The fluorimetric method allows the determination of 0.060-0.600 μg ml⁻¹ of garenoxacin in aqueous solution containing HCl/KCl buffer (pH 1.5) with λ_exc=282 nm and λ_em=421 nm. Micellar-enhanced fluorescence was also studied, leading to a higher than 400% increase in analytical signal in presence of 12 mM sodium dodecyl sulphate (SDS), allowing the determination of 0.020-0.750 μg ml⁻¹ of garenoxacin. The terbium-sensitised luminescence method allows the determination of 0.100-1.500 μg ml⁻¹ of garenoxacin in 12 mM SDS solution containing 0.08 M acetic acid/sodium acetate buffer (pH 4.1) and 7.5 mM Na₂SO₃ (chemical deoxygenation agent), with λ_exc=281 nm and λ_em=546 nm. Relative standard deviation (R.S.D.) values for the three methods were in the range 1.0-2.0%. The proposed procedures have been applied to the determination of garenoxacin in spiked human urine and serum.     

Sensitive fluorimetric method for the determination of aniline by using tetra-substituted amino aluminium phthalocyanine

This is the first report of the determination of aniline with tetra-substituted amino aluminium phthalocyanine (TAAlPc) by a fluorimetric method. In KBr-HCl solution, nitrite ion diazotizes TAAlPc, thus, the fluorescence of TAAlPc is dramatically quenched. However, there is less quenching in the presence of aniline and the recovery in fluorescence intensity is linear with the concentration of aniline. Based on this, a novel method has been developed for the determination of aniline in aqueous solutions. Under the optimal conditions, the calibration graph for aniline is from 5 to 300 ng ml⁻¹ with a 3σ limit of detection of 1.8 ng ml⁻¹. The relative standard deviation for nine replicate measurements of 100 ng ml⁻¹ aniline is 1.7%. The method was applied to the analysis of water samples with satisfactory results.     

On-line separation, preconcentration and determination of trace amounts of gold in mineral sample by flow injection catalytic kinetic spectrofluorimetry

2-Pyridine carboxaldehyde furfuralhydrazone (PCFH) was newly synthesized and its ionization, IR and elemental analysis were established. An on-line separation and preconcentration system was developed for the flow injection (FI) catalytic kinetic spectrofluorimetric determination of trace amounts of gold. The method was based on the fluorescence enhancing reaction of PCFH with potassium bromate, which was catalysed by Au³⁺ in aqueous medium at pH 4.20 and 35 °C. A micro polyamide resin column was used to separate and collect gold from sample solution. Under these experimental conditions, the oxidized product of PCFH had excitation and emission maxima at 296 and 404 nm, respectively. The linear range of this method was 0.53-144 ng ml⁻¹ with the RSD of 1.6%. The detection limit was 0.16 ng ml⁻¹. A high analysis rate of 15 samples h⁻¹ was obtained. The proposed method had been applied successfully to the determination of gold in synthetic mixture and mineral sample with satisfactory results.     

A passive sampling-based analytical strategy for the determination of volatile organic compounds in the air of working areas

An analytical methodology based on the use of a polyethylene layflat tube filled with activated carbon and Florisil (ACFL-VERAM) was employed for the passive sampling of volatile organic compounds (VOCs) in the air of working areas of packing industries. VOCs amount in the ACFL-VERAM sampler was directly determined through head-space-gas chromatography-mass spectrometry (HS-GC-MS) allowing a direct determination in only 20 min without the need of any previous treatment. Uptake parameters, like sampling rate (R_S) and sampler-air partition coefficient (K_SA), were determined for every studied VOC from adsorption isotherm data. Additionally, experimental equations have been proposed to predict R_S and K_SA from the octanol-air partition coefficients reported in the literature. The proposed methodology reaches method detection levels from 0.007 to 0.2 mg m⁻³ for the studied VOCs.     

Studies on the supramolecular interaction between napropamide and β-cyclodextrin by spectrofluorimetry and its analytical application

The supramolecular interaction between N,N-diethyl-2-(1-naphthalenyloxy)propanamide (napropamide) and β-cyclodextrin (β-CD) has been studied by spectrofluorimetry. The results showed that β-CD reacted with napropamide to form an inclusion complex with an association constant of 3.18×10³ l mol⁻¹. The composition of the complex was 1:1 (β-CD:napropamide). Based on the significant enhancement of fluorescence intensity of napropamide in inclusion complex, a spetrofluorimetric method with high sensitivity and selectivity was developed for the determination of napropamide in aqueous solution. Under the optimum conditions, the complex had excitation and emission maxima at 285 and 339 nm, respectively. The linear range of the method was 3.7-1500 ng ml⁻¹ with a detection limit of 1.1 ng ml⁻¹. The proposed method was successfully used to determine napropamide in river water.     

Determination of thyroxine hormone by luminol chemiluminescence

A chemiluminescence (CL) flow system for determination of thyroxine (Thy) is presented. It is based on the catalytic effect of cobalt(II) on the CL reaction between luminol and hydrogen peroxide. The iodinated chemical structure of Thy causes a heavy atom effect. The luminol CL signals show significant quenching by Thy. The calibration graph for Thy is linear for 15-70 μg ml⁻¹ and the 3σ detection limits are 27 μg ml⁻¹ for d-Thy and 23 μg ml⁻¹ for l-Thy.     

Flow-through optosensing of 1-naphthaleneacetic acid in water and apples by heavy atom induced-room temperature phosphorescence measurements

A sensitive and selective phosphorimetric method for the determination of 1-naphthaleneacetic acid (1-NAA) based on a flow-injection system connected to a flow cell packed with a solid support and placed in the sample compartment of a conventional luminescence spectrometer is described. A non-ionic solid polymeric resin Amberlite XAD-7 is used for the packing. After injection of the sample, 1-NAA is on-line retained in the packed resin and measurements of the heavy atom induced (HAI)-room temperature phosphorescence (RTP) emission (λ_ex/λ_em = 292/490 nm) from this native luminescent compound are taken.The optimum experimental conditions were investigated by injecting 2 ml samples of an aqueous solution of 1-NAA in the flow system. A concentration 0.15 mol l⁻¹ of thallium(I) ions, as heavy atom, both in the samples and the carrier flow, was finally selected. Also, a concentration of 6 mmol l⁻¹ of sulphite was optimal for ensuring the necessary deoxygenation of the system at the selected flow rate of 0.8 ml min⁻¹. After measurement, the solid support was efficiently regenerated by injecting 1 ml of a mixture water:acetone in a ratio 1:1 (v/v) into the flow.The detection limit (3σ criterion) was 1.2 ng ml⁻¹ of 1-NAA. The repeatability (R.S.D.) for five replicates of a sample containing 50 ng ml⁻¹ of analyte turned out to be ±3% and the calibration graphs proved to be linear up to 500 ng ml⁻¹ of 1-NAA (maximum concentration assayed). The effect of potential interferences from other organic species which can be also used as plant growth regulators, as well as from various inorganic cations and anions, has been investigated as well.The method was successfully applied to the determination of low levels of this plant growth regulator in natural waters (river and fountain waters) and apples.     

Electrochemiluminescence assay for the detection of acridinium esters

An electrochemiluminescence (ECL)-based method for rapid and sensitive detection of acridinium ester in neutral solution was described. Strong ECL emission was observed when a positive voltage over 2.0 V (versus Ag/AgCl) was applied to the working electrode (Pt) immersed in the acridinium ester solution of 2.0 mol l⁻¹ KNO₃ (pH 7.0). The possible ECL mechanism was discussed. It was proposed that the ECL emission came out of N-methylacridone, the oxidization product of acridinium ester by the nascent oxygen generated on the surface of working electrode in the course of oxidization of water. Other influenced factors including the electrochemical parameters, the ECL reaction medium and pH value, were investigated in detail. Under the optimal conditions, ECL intensity has a linear relationship with the concentration of acridinium ester in the range of 0.24-96 ng ml⁻¹ (r=0.9999). The relative standard deviation for 24 ng ml⁻¹ acridinium ester was 4.6% (n=11). The limit of detection was 0.16 ng ml⁻¹.     

Direct spectrophotometric determination of calcium in clinical samples with carboxyazo-p-CH3

A highly sensitive and relatively interference-free spectrophotometric method for determination of calcium is described. The method is based on the reaction between calcium ions and carboxyazo-p-CH₃ in aqueous citrate medium of pH 7, to form a blue complex with maximum absorption at 716 nm. The calibration is linear up to 0.12 μg ml⁻¹ calcium with a repeatability (R.S.D.) of 1.0% at a concentration of 0.04 μg ml⁻¹ (n=5). The molar absorptivity of the complex and Sandell’s sensitivity are 3.5×10⁵ l mol⁻¹ cm⁻¹ and 0.11 ng cm⁻², its 10σ limit of quantification and the 3σ limit of detection were found to be 0.3 ng ml⁻¹ and 0.09 ng ml⁻¹ respectively. The influence of reaction variables and the effect of interfering ions are studied; no interference was observed in clinical samples. The proposed method has been applied directly to the determination of calcium in clinical samples without the need for pre-concentration, masking metal ions and digesting samples.     

Determination of substituted benzenes in water samples by fiber-in-tube liquid phase microextraction coupled with gas chromatography

A method for determination of toluene, ethylbenzene, p-xylene, o-xylene, 1,3,5-trimethylbenzene and 1,2,4-trimethylbenzene in water samples was developed by a fiber-in-tube liquid phase microextraction technique (fiber-in-tube LPME) coupled with GC-flame ionization detector (FID). The method used a tube packed with polytetrafluoroethylene (PTFE) fibers as an extraction medium, improving the stableness of the solvent and the performance of extraction. Certain amounts of curled PTFE fibers were packed into a section of PTFE tube. Because the fibers were curled, they formed network structure in the tube. The fiber packed tube was firstly immersed into organic solvent to be filled with organic solvent and then was exposing to an aqueous solution to extract the target compounds. The extract was then retracted by a conventional GC microsyringe and analyzed by GC-FID. Extraction of the analytes in 8 ml aqueous solution for 15 min yielded enrichment factors of 224-361. The precision (R.S.D., n = 5) was 3.6-8.1% for peak area. The limit of detection (LOD, S/N = 3) for the six substituted benzenes were in the range of 0.3-5.0 μg l⁻¹.     

Determination of ibuprofen and novocaine hydrochloride with the use of water-micellar solutions of surfactants

The solubility and acid-base properties of ibuprofen in water-micellar media of surfactants were studied. A new visual method for the titrimetric determination of ibuprofen in pure form was proposed. The smallest pK value (4.43) and the greatest solubility (8.1 mg ml⁻¹) of ibuprofen were achieved using an aqueous cationic micellar medium of 0.1 M tridecylpyridinium bromide. The titration was performed with 0.05 M potassium hydroxide aqueous solution and the exact end-point was determined with the use of xylenol blue as indicator. Conditions for the individual determination of ibuprofen and novocaine hydrochloride in their 1:1 mixtures with the use of 0.1 M tridecylpyridinium bromide were proposed.     

Determination of ternary mixtures of penicillin G, benzathine and procaine by liquid chromatography and factorial design study

In the present work, a rapid and sensitive method for simultaneous determination of penicillin G (PG), benzathine (BE) and procaine (PR) in drug and serum media is introduced. The polar hydro-organic (55/45) mobile phases containing an aqueous solution adjusted to pH = 3.7 and an organic solvent (MeOH) including triethylamine (TEA) and trifluroacetic acid (TFA) are used. The flow rate of 1 ml min⁻¹, a C₈ column (150 mm × 46 mm) with 5 μm i.d. and wavelength at 215 nm are selected for optimal separation condition. The limit of detection (LOD), linear concentration range and relative standard deviation (R.S.D.) of this method for the PG are 1.1 μg ml⁻¹, 10-2400 μg ml⁻¹ and 1.7% and for the BE are 1.2 μg ml⁻¹, 12-2100 μg ml⁻¹ and 1.8% and for the PR are 1.5 μg ml⁻¹, 20-2000 μg ml⁻¹ and 2%, respectively. The factorial design is used for the determination of main and interaction effects of pH, flow rate and concentration of MeOH, TEA and TFA in the separation at two levels. Also, the analysis of variance (ANOVA) table is obtained. The results show that TFA and TEA have higher effect than concentration of MeOH, pH and flow rate factors.     

Room-temperature luminescence optosensings based on immobilized active principles actives: Application to nafronyl and naproxen determination in pharmaceutical preparations and biological fluids

This paper presents two easy and selective methods for determining the active principles nafronyl (NFL) and naproxen (NAP), using a flow-through fluorescence optosensor based on the on-line immobilization on a nonionic-exchanger (Silica Gel, Davisil™ and Amberlite XAD 7, respectively) solid support. The determination was performed in 5×10⁻³ M HAc/NaAc buffer solution at pH 5 for NFL and 15×10⁻³ M glycine/HCl buffer solution at pH 2.5 for NAP at a working temperature of 20 °C. The fluorescence intensities were measured at λ_ex/em=294/336 nm and λ_ex/em=332/354 nm for NFL and NAP, respectively. The response time for these optosensors were practically instant, obtaining a linear concentration range between 0 and 700.0 ng ml⁻¹ with a detection limit of 20.8 ng ml⁻¹, an analytical sensitivity of 10.1 ng ml⁻¹ and a standard deviation of 1.27% at a 500 ng ml⁻¹ concentration level for NFL and a linear concentration range between 0 and 200.0 ng ml⁻¹ with the detection limit of 13.3 ng ml⁻¹, an analytical sensitivity of 6.0 ng ml⁻¹ and a standard deviation of 3.52% at a 100 ng ml⁻¹ concentration level for NAP. The proposed methods were satisfactorily applied to real samples (three commercial formulations and urine samples). The effects of the possible interferences were evaluated in all cases.