Liquid-supported membranes in chromium(VI) optical sensing: transport modelling

Flat sheet liquid-supported membranes (FSLSM) containing Aliquat 336 as a carrier have been evaluated as sample interface in an optical sensor for Cr(VI) monitoring. A model describing the transport mechanism of Cr(VI) through the membrane is reported. The model considers a diffusion process through a feed aqueous diffusion layer, a fast interfacial chemical reaction and a diffusion of ALQHCrO₄ and (ALQ)₂CrO₄ species through the membrane (Aliquat 336, ALQ). The mathematical equations describing the transport rate are derived and they correlate the membrane permeability coefficient to diffusional and equilibrium parameters as well as to the chemical composition of the system, i.e. extractant concentration in the membrane phase and acidity in the feed phase. The experimental data are explained by the derived equations and the diffusion resistances to mass transfer are evaluated. The influence of other experimental parameters, such as stirring speed in the feed phase and nature of the diluent and stripping agent on the transport is also discussed. Experiments with optical detection demonstrate the suitability of liquid-supported membranes (LSM) containing ALQ as interfaces for optical sensing.     

Preparation of calix[4]arene-embedded polysulphone membranes,and utilisation of its Cr(VI) transport efficiency

In this study, a tetramine-substituted calix[4]arene derivative, which was synthesised from calix[4]arene by treatment with dimethylamine in one step via Mannich reaction, was used to fabricate a new calix[4]arene-embedded polysulphone membrane (calix@membrane). Its structure and surface morphology were determined using thermogravimetric analysis and scanning electron microscopy, and elemental analysis techniques. Moreover, a Donnan dialysis system was employed to investigate Cr(VI) transport efficacy of calix@membrane at different pH values. Results showed that calix@membrane represented a promising transport capability for HCr₂O₇^? due to their efficient complexation behaviour.     

Adsorption Characteristics of Chromium(VI) on Granular Activated Carbon

The adsorption of Chromium(VI) from aqueous solutions was studied on different commercial grades of granular activated carbon namely Filtrasorb F‐400, F‐300, F‐200 and F‐100. The adsorption of Chromium (VI) on F‐400 carbon was found to be maximum in comparison to the other grades of carbon. The Chromium (VI) adsorption process in dilute aqueous solutions agreed with the Langmuir and Freundlich models and also obeyed first order kinetics. Metal sorption characteristics of as received activated carbons were measured in batch experiments. The maximum removal (60–65%) for different grades of raw carbon was observed at 25 °C with an initial concentration of 15.16 mg dm^?3. It is evident from the study that granular activated carbon holds a particular promise in the removal of metal ions from aqueous solutions.     

Polyethylenimine Functionalized Multi‐walled Carbon Nanotubes for Electrochemical Detection of Chromium(VI)

Multi‐walled carbon nanotubes (MWCNTs) functionalized with polyethylenimine (PEI) were synthesized and characterized by dispersibility, field‐emission scanning electron microscope (FE‐SEM), FT‐IR and thermogravimetric Analyzer (TGA). The glassy carbon electrodes modified by MWCNT‐PEI composite were used for sensitive and selective detection of chromium (VI). A linear response was obtained over a wide range of Cr(VI) concentrations (0.002–20 µmol L^?1) with the detection limit of 0.0006 µmol L^?1 (S/N=3). The proposed electrodes were used successfully for Cr(VI) detection in three real water samples.     

Spectrophotometric determination of Chromium(VI) using cyclam as a reagent

A simple, rapid, sensitive, and inexpensive method for spectrophotometric determination of chromium(VI), based on the absorbance of its complex with 1,4,8,11-tetraazacyclotetradecane (cyclam) is presented. The complex showed a molar absorbtivity of 1.5?×?10⁴?L?mol^?1?cm^?1 at 379?nm. Under optimum experimental conditions, a pH of 4.5 and 1.960?×?10³?mg?L^?1 cyclam were selected, and all measurements were performed 10?min after mixing. Major cations and anions did not show any interference; Beer's law was applicable in the concentration range 0.2–20?mg?L^?1 with a detection limit of 0.001?mg?L^?1. The standard deviation in the determination is ±0.5?mg?L^?1 for a 15.0?mg?L^?1 solution (n?=?7). The described method provides a simple and reliable means for determination of Cr(VI) in real samples.     

Anion exchange membrane with viologen moiety as anion exchange groups and generation of photo-induced electrical potential from the membrane

An anion exchange membrane with a viologen moiety was prepared by the reaction of a film of chloromethylated polysulfone and 4,4′-bipyridine. The anion exchange membrane showed a high electrical resistance and a high transport number of anions due to the development of high crosslinking by the diamine. After the membrane had been swollen with ethylene glycol, photo-voltage and photo-current (82 mV, 410 nA at 200 kΩ load, 160 μm thick membrane) were generated from the membrane upon photo-irradiation.     

Preparation and characterization of Type II anion exchange membranes from poly(2,6-dimethyl-1,4-phenylene oxide) (PPO)

To separate hydrophilic anions from hydrophobic ones, Type II PPO-based anion exchange membranes were developed. Different from Type I (with both trimethylbenzylammonium and triethylbenzylammonium groups), Type II has an excellent hydrophobicity modifier as fixed groups: dimethyethanolammonium groups, which were introduced into PPO (poly(2,6-dimethyl-1,4-phenylene oxide)) by following benzyl bromination of PPO and subsequent quaternary amination with a dimethylethanolamine (DMEA) aqueous solution. The membrane's intrinsic properties are dependent on DMEA concentration and amination temperature. The optimum conditions for membrane preparation are as follows: amination temperature 70 °C, time 30–48 h, and DMEA concentration 1:3–1:5 (v/v, DMEA to water). The obtained Type II anion exchange membranes had an IEC of 1.5 mmol/g dry membrane, water content of 30%, and membrane area resistance of 30 Ω cm². The introduced dimethyethanolammonium groups can block hydrated anions from the access to membranes but let hydrophobic anions transport; hence, an effective separation between hydrophilic and hydrophobic anions can be achieved during electro-membrane operation.     

Removal of Chromium(VI) from Groundwater Using Oil Shale Ash Supported Nanoscaled Zero-valent Iron

Oil shale ash(OSA) supported nanoscaled zero-valent iron(OSA-nZVI) was used as a rapid and efficient reductant for Cr(VI) reduction. The optimal mass ratio of nZVI to OSA and the optimal dosage were explored. The effects of initial pH, reaction temperature, initial Cr(VI) concentration, and common cations and anions in groundwater on Cr(VI) reduction were determined in batch experiments. The results show that the optimum initial pH is 5.0. The reaction temperature has a positive effect on Cr(VI) reduction while the real groundwater has a negative effect. Additionally, 84.22% Cr(VI) was still reduced by 3 g/L OSA-nZVI(1:2)(mass ratio of OSA to Fe⁰ was 1:2) within 120 min for 50 mg/L Cr(VI) under conditions of 10℃ and unadjusted pH.     

Normal Pulse Voltammetric Determination of Subnanomolar Concentrations of Chromium(VI) with Continuous Wavelet Transformation

The renewable mercury film‐modified silver solid amalgam annular band electrode (MF‐AgSAE) applied for quantitative determination of sub‐nanomolar concentrations of Cr(VI) using differential pulse (DP) and normal pulse (NP) catalytic adsorptive striping voltammetry (CAdSV) is presented. In this context a signal processing algorithm is described and applied for the transformation of sigmoidal shaped NP curves to peak shaped curves. The method utilizes continuous wavelet transform (CWT) and a specially constructed mother wavelet defined using the ideal wave‐shaped curve. It simplifies the interpretation of sigmoidal curves. In the effect the new strategy of Cr(VI) determination is 10 times more sensitive than differential pulse and square‐wave techniques. The reproducibility is below 3–5 % (n=3) for the 0.2–2.2 nM concentration range of Cr(VI). The detection limit for 30 s preconcentration is equal to 0.05 nM with sensitivity of 0.809±0.012 µA nM^?1 and is limited by the purity of the used reagents. The correlation coefficient is equal to 0.9993. For 2 nM of Cr(VI), in the tested range, 0≤t_acc≤60 s, the relation wave height? accumulation time (I_w–t_acc) is linear. The operation and effectiveness of the proposed procedures was confirmed by the quantitative determination of Cr(VI) in supporting electrolyte and CRM (surface water samples and urine) with known amounts of the analyte. The obtained results show substantial improvement of the performance of NP CAdSV technique.     

Adsorption of Chromium (VI) on <Emphasis Type="Italic">Azadirachta Indica</Emphasis> (Neem) Leaf Powder

A novel adsorbent was developed from mature leaves of the Neem tree (Azadirachta Indica) for removing metal ions from water. The adsorbent, in the form of fine powder, was found to be very effective in removing chromium (VI) from aqueous solution. The adsorption was carried out in a batch process taking different concentrations of the metal ion in aqueous solution with variation in adsorbent amount, pH, agitation time and temperature. The suitability of the adsorbent was tested with Langmuir and Freundlich isotherms and with various equilibrium kinetic data. A small amount of the Neem Leaf Powder (NLP) (1.6 g dm^–3) could remove as much as 87% of Cr (VI) in 300 min from a solution of concentration 14.1 mg dm^–3 at 300 K. The optimum range of pH for the adsorption process was 4.5–7.5 and since the natural pH of the Cr (VI) solution was 5.5, no addition of acid or alkali was necessary for achieving maximum adsorption. The adsorption coefficients indicated a high potentiality for the NLP to be used as an adsorbent for removing Cr (VI) from water.     

Preparation of NOx modified PMMA-EGDM composite membrane for the recovery of chromium (VI)

A non-interpenetrating cross-linked poly (methyl methacrylate-ethylene glycol dimethacrylate) copolymer ultrafiltration membrane on a microporous ceramic support has been prepared from the monomers in two stages. The polymer membranes thus obtained have been nitrated using NO_x (a mixture of NO and NO₂) by the gas phase reaction at 80 °C. Separation experiments on the chromium (VI) salt solution have been carried out using unmodified (giving 68% rejection per pass) and nitrated membranes (giving as much as 67% rejection per pass). For nitrated membranes, the water flux and the solute flux increased with time of nitration about hundred folds because of the increase in the hydrophilicity as well as the pore size.     

Industrial recovery of mixed acid (HF + HNO3) from the titanium spent leaching solutions by diffusion dialysis with a new series of anion exchange membranes

The results of the development of the industrial diffusion dialysis technology and the unit based on it for mixed acid recovery from titanium metal processing have been considered. Mixed acid can be selectively separated from the spent liquor contained mainly HNO₃, HF and titanium ions by diffusion dialysis using a new series of anion exchange membranes. The results showed that this separation is seriously affected by the membrane water content and ion exchange capacity (IEC). Some titanium complex anion (TiF₆)²⁻ give rise to the difficulty in separation so that the best separation efficiency does not occur at the cases of high water content and IEC of membranes. By controlling the membrane preparation conditions (bromination content and position), a desired membrane for this system has been obtained with both relatively high acid recovery ratio and acid/titanium selectivity.

Economic estimation was conducted based on an industrial diffusion dialyser with 499 sheets of 1600 mm×800 mm membrane and the practical runs parameters: process quantity 2400 m³ per year, total acid recovery ratio 85%. The results showed that the investment could be recovered within 5 months. After 5 years’ run, one such dialyser can bring about CN$ 4.3 million profits besides the significant environmental benefits.     

Column chromatographic speciation of chromium for Cr(VI) and several species of Cr(III)

Summary Chromium can be present in aqueous solution as Cr(VI) or in monomeric, dimeric, trimeric and higher polymeric forms of Cr(III). Many monomeric forms of Cr(III) are possible, with the water molecules of Cr(H₂O) ₆ ³⁺ substituted by anionic or neutral species. This proliferation of Cr(III) species makes the complete speciation of chromium a continuing challenge to the analyst. A simple and effective cation exchange procedure for the separation of various of these species uses a small glass column containing 1 mL of pre-treated cation exchange resin (Na⁺ form). Stepwise elution with solutions of perchloric acid, Ca²⁺ (pH=2) and La³⁺ (pH=2) separates Cr(VI) and seven Cr(III) species from CrX₃ to tetramer. Radiometric (Cr-51), spectrophotometric and other detection methods can be employed; the use of radiochromium gives the lowest detection limit.     

Study of the Complexation,Adsorption and Electrode Reaction Mechanisms of Chromium(VI) and (III) with DTPA Under Adsorptive Stripping Voltammetric Conditions

The complexation of Cr(III) and Cr(VI) with diethylenetriaminepentaacetic acid (DTPA), the redox behavior of these complexes and their adsorption on the mercury electrode surface were investigated by a combination of electrochemical techniques and UV/vis spectroscopy. A homogenous two‐step reaction was observed when mixing Cr(III), present as hexaquo complex, with DTPA. The first reaction product, the electroactive 1 : 1 complex, turns into an electroinactive form in the second step. The results indicate that the second reaction product is presumably a 1 : 2 Cr(III)/DTPA complex. The electroreduction of the DTPA‐Cr(III) complex to Cr(II) was found to be diffusion rather than adsorption controlled.The Cr(III) ion, generated in‐situ from Cr(VI) at the mercury electrode at about ?50 mV (vs. Ag|AgCl) (3 mol L^?1 KCl), was found to form instantly an electroactive and adsorbable complex with DTPA. By means of electrocapillary measurements its surface activity was shown to be 30 times higher than that of the complex built by homogenous reaction of DTPA with the hydrated Cr(III). Both components, DTPA and the in‐situ built complex Cr(III) ion were found to adsorb on the mercury electrode.The effect of nitrate, used as catalytic oxidant in the voltammetric determination method, on the complexation reaction and on the adsorption processes was found to be negligible.The proposed complex structures and an overall reaction scheme are shown.     

Isolation of Chromium(VI) from Aqueous Solution by Electromembrane Extraction

Electromembrane extraction (EME) is a powerful extraction and preconcentration technique for ionizable species. However, the ionic contents in the sample can influence the extraction efficiency and system stability due to electrolysis. In this work, the electromembrane extraction of chromium(VI) was developed using various levels of ionic samples. 2-Nitrophenyl octyl ether was the most suitable supported liquid membrane that delayed the electrolytic occurrence of air bubbles at the electrodes due to its high viscosity and high dielectric constant properties. The electromembrane extraction method was optimized using 5?mM NaCl (630?µS?cm^?1); the applied potential was 100?V and the extraction time was 15?min. The enrichment factor of 80 was obtained over a linear working range of 10.0–80.0?µg?L^?1. The method performance was tested using mineral water, drinking water, tap water, and surface water. The method recoveries based on matrix-matched calibration were 95–125% with standard deviations within 15%.     

Simultaneous determination of Cr(III) and Cr(VI) in water by reversed phase HPLC,after chelating with sodium diethyldithiocarbamate

Summary A method for simultaneous determination of Cr(III) and Cr(VI), using sodium diethyldithiocarbamate as chelating agent is given. At room temperature and pH 5.8 sodium diethyldithiocarbamate reacts with both Cr(III) and Cr(VI). Examination of this reaction by reversed phase high-performance liquid chromatography, makes it possible to correct for the interference between Cr(III) and Cr(VI) when determining the amount of Cr(III) present in the solution.     

Elastic and durable multi-cation-crosslinked anion exchange membrane based on poly(styrene-b-(ethylene-co-butylene)-b-styrene)

Anion exchange membranes (AEMs), as the core component of the new generation anion exchange membrane fuel cells (AEMFCs), directly determine the performance and the lifetime of this energy conversion device. Here, AEMs with pendant multiple quaternary ammonium anchored onto the poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) backbone are synthesized. The comb-shaped copolymer SEBS-C16 is synthesized with N,N-dimethyl-1-hexadecylamine and chloromethylated SEBS to improve solubility, then the multi-cation crosslinker is prepared and grafted on the above backbone to fabricate a series of flexible multi-cation crosslinked SEBS-based AEMs (SEBS-C16-xC4, where x% is the ratio of the crosslinker to polystyrene block) with practical properties. The obtained SEBS-C16-20C4 membrane exhibits a microphase separated morphology with an interdomain spacing of 18.87 nm. Benefited from the ion channels, SEBS-C16-20C4 shows high conductivity of 77.78 mS/cm at 80°C. Additionally, the prepared SEBS-C16-20C4 membrane with ion exchange capacity of 2.35 mmol/g also exhibits enhanced alkaline stability (5.87% hydroxide conductivity decrease in 2 M NaOH solution at 80°C after 1,700 hr) and improved mechanical properties, compared with the non-crosslinked SEBS-C16 sample. Furthermore, AEMFC single cell performance is evaluated with the SEBS-C16-20C4 membrane, and a maximum power density of 182 mW/cm² is achieved at 80°C under H₂/O₂ conditions.     

Electroanalytical Detection of Cr(VI) and Cr(III) Ions Using a Novel Microbial Sensor

A microbial sensor, namely carbon paste electrode (CPE) modified with Citrobacter freundii (Cf–CPE) has been developed for the detection of hexavalent (Cr(VI)) and trivalent (Cr(III)) chromium present in aqueous samples using voltammetry, an electroanalytical technique. The biosensor developed, demonstrated about a twofold higher performance as compared to the bare CPE for the chosen ions. Using cyclic voltammetry and by employing the fabricated Cf–CPE, the lowest limit of detection (LLOD) of 1x10⁻⁴ M and 5x10⁻⁴ M for Cr(VI) and Cr(III) ions respectively could be achieved. By adopting the Differential Pulse Cathodic Stripping Voltammetric technique, the LLOD could be further improved to 1x10⁻⁹ M and 1x10⁻⁷ M for Cr(VI) and Cr(III) ions respectively using the biomodified electrodes. The reactions occurring at the electrode surface‐chromium solution interface and the mechanisms of biosorption of chromium species onto the biosensor are discussed. The stability and utility of the developed biosensor for the analysis of Cr(VI) and Cr(III) ions in chromite mine water samples has been evaluated.     

A novel fluorescent distinguished probe for Cr (VI) in aqueous solution

Salicylaldehyde rhodamine B hydrazone (SRBH) was developed as a new spectrofluorimetric probe for the selective and sensitive detection of CrO₄²⁻ in acidic conditions. The proposed method was based on the special oxidation reaction between non-fluorescent SRBH by potassium dichromate to produce a highly fluorescent rhodamine B, as a product. Under the optimum conditions described, the fluorescence enhancement at 591 nm was good linearly related to the concentration of CrO₄²⁻ from 1.0 × 10⁻⁸ to 3.0 × 10⁻⁷ M (0.42–12.6 ng mL⁻¹) with a correlation coefficient of R² = 0.9989 (n = 10) and a detection limit of 1.5 × 10⁻⁹ M (0.063 ng mL⁻¹). The relative standard deviation (R.S.D.) was 2.0% (n = 6). The proposed method was also successfully applied to the determination of chromium (VI) in drinking water, river water and synthetic samples.     

Poly(phenylene oxide) copolymer anion exchange membranes

Poly(phenylene oxide) block and random copolymers are synthesized by oxidative polymerization of 2,6-dimethylphenol and 2,6-diphenylphenol for potential alkaline exchange membrane application. The copolymers are functionalized on the methyl substituted repeat units through a two-step process to produce pendent quaternary ammonium cationic groups. The amount of quaternary ammonium cations and the ion exchange capacity are quantified through titration measurements. Ionic conductivity of the copolymer membranes is measured by electrochemical impedance spectroscopy. Block copolymers show increased bromide conductivity at higher ion exchange capacities compared with the random copolymer analogs. The bromide conductivity for a block copolymer film with an ion exchange capacity of 1.27 mequiv/g reaches 26 mS/cm at 90 °C and 95% relative humidity. The hydroxide conductivity for the same film was measured to be 84 mS/cm at 80 °C and 95% relative humidity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1770–1778, 2013