Comparison of different excitation methods for X-ray spectral analysis: the case of synchrotron radiation

Different excitation means, protons, photons and electrons (PIXE, XRFA, and EPMA, respectively) have previously been compared with regard to the figures of merit, i.e. detection power, precision and accuracy. The aim in this article is to compare synchrotron radiation SR as another excitation method with the methods mentioned above. From this point of view the evaluation of (SR) was missing as an again independently optimized excitation method and was based as previously on practical problems of trace analysis, in this case on the determinations of traces in lead. The experiment has been performed with thick homogeneous samples of lead, the same samples already used in the former work, so that a direct comparison is possible. The calculation of the figures of merit is based on the measurements of the blank values and their relative standard deviation for the detection limit and on the random errors for the precision. Regarding the thick homogeneous target of lead XRFA still turns out to be the best method, whereas Synchrotron X-Ray Fluorescence SY-XRF compares favorably, at least for larger atomic numbers Z. Even PIXE is inferior to (SY-XRF) in the case of larger Z; when information on the lateral distribution of the elements is of interest, PIXE is indispensable. Received: 13 June 2000 / Revised: 2 August 2000 / Accepted: 5 August 2000     

Comprehensive analytical figures of merit for fluorimetry of polynuclear aromatic hydrocarbons

The analytical figures of merit for fluorescence of sixty polynuclear aromatic hydrocarbons are presented. The limits of detection for most of the compounds are below 50 ng ml^-1 and the average relative standard deviation at 1 μg ml^-1 for each compound is 1.4%. The fluorescence excitation and emission peak wavelengths are listed. These results confirm the excellent detection limits and precision offered by this technique for quantification of polynuclear aromatic hydrocarbons.     

Fourier transform u.v.-visible molecular luminescence spectrometry: Fluorescence excitation spectra

The analytical utility of Fourier transform spectrometry in the u.v.-vis region was investigated. Molecular fluorescence excitation spectra were acquired for four polycyclic aromatic hydrocarbons frozen in Shpol'skii solvents. Analytical figures of merit were determined for coronene, including a limit of detection of 2 ppb and a precision better than 13% RSD. The major sources of noise in FT/u.v. molecular fluorescence spectrometry are discussed, and results are compared to those reported earlier from wavelength dispersive instruments.     

Direct spectrometry of solids in view of information characteristics

The development of atomic spectrometric methods in recent years is characterized by a remarkable orientation towards direct analysis of solids using various sample introduction techniques in connection with inductively coupled plasma excitation. The old-fashioned direct-current arc excitation with computer-controlled arc current vs. time programming has been studied as an alternative to the above mentioned methods. The influence of different electrode material, different sample preparation mode and working atmosphere on the main figures of merit (precision of the method, dynamic concentration range, determination limit, etc.) have been studied using an evaluation procedure based on the information theory. Received: 3 June 1998 / Revised: 15 July 1998 / Accepted: 18 July 1998     

Advantages of PARAFAC calibration in the determination of malachite green and its metabolite in fish by liquid chromatography-tandem mass spectrometry

This paper reports the properties and advantages of the three-way calibration models based on parallel factor analysis (PARAFAC) in the simultaneous determination of malachite green (MG) and its metabolite (leucomalachite green, LMG) in trout. A recently method proposed by community reference laboratory AFSSA-LERMVD (Fougères, France) has been used. The method is based on liquid chromatography-triple quadrupole mass spectrometry (LC-MS/MS) in multiple reaction monitoring (MRM) mode. The validation of the method has been carried out taking into account the Decision 2002/657/EC. The figures of merit for PARAFAC and univariate calibration models of six non-consecutive days analyzed during a month were evaluated. With the samples of the first 3 days, calibration models were built and the fish fortification samples of the other days were predicted. Decision limits (CCalpha, alpha=0.01), detection capabilities (CCbeta, beta=0.05) and mean relative errors in absolute value (in calibration and with test samples) obtained with PARAFAC calibrations were more homogeneous than the ones obtained with the univariate calibrations, especially in LMG. These figures of merit were in the range of 0.2-0.83 microg kg(-1) (CCbeta) and 0.2-0.49 microg kg(-1) (CCalpha), whereas mean relative errors in absolute value were in the range of 1.1-7.4% in calibration and 3-12% in test samples for MG and LMG with PARAFAC calibrations. The PARAFAC calibrations allow detecting the test samples which are not similar to the calibration samples and in this way their wrong quantification is avoided.     

Simultaneous or scanning data acquisition? A theoretical comparison relevant to inductively coupled plasma sector-field mass spectrometers

The benefits of simultaneous multichannel detection over single-channel scanning detection are well established in analytical chemistry. Multichannel detection increases duty cycle, which leads to enhanced sensitivity, detection limits, and reduced analysis time. Also, multichannel detection used with either isotope-ratio or internal-standard techniques provides a mechanism to reduce the effect of multiplicative or flicker noise prevalent in plasma sources. An additional benefit of simultaneous detection is superior analysis of short-lived transient signals. Presented here is a theoretical comparison between simultaneous/continuous multichannel acquisition and single-channel scanning acquisition. To conduct this comparison, reported sensitivity, single-channel precision, and background values for commercial inductively coupled plasma sector-field mass spectrometers (ICP-SFMS) are used to generate theoretical figures of merit for both acquisition methods. Among the figures of merit that will be considered are detection limits, precision, and analysis time, particularly for multi-element or multi-isotope analysis.     

Spectrophotometric determination of sorbic and benzoic acids in fruit juices by a net analyte signal-based method with selection of the wavelength range to avoid non-modelled interferences

Sorbic (SOR) and benzoic (BEN) acids were determined in fruit juice samples by using a net analyte signal-based methodology named HLA/GO (an hybrid linear analysis presented by Goicoechea and Olivieri) applied to spectroscopic signals. The calibration set was built with several fruit juices in order to take into account the natural variability and concentrations of both analytes covering the range usually present in commercial samples. Relative errors of prediction (REP %) of 3.6 and 5.2% were calculated for SOR and BEN respectively. Several figures of merit were calculated-sensitivity, selectivity, analytical sensitivity, and limit of detection. The method is quantitative, with reasonably good recoveries and excellent precision (less than 1%). Wavelength selection was applied, based on the concept of net analyte signal regression, and it allowed us to improve the method performance in samples containing non-modelled interferences, e.g. fruit juices different to those used to build the calibration model.     

XRF induced by PIXE: Comparison with PIXE

Two different modes of sample excitation have been used for elemental analysis of thin standard reference materials and of chemical standards with known composition. PIXE /2.5 MeV protons/ and XRF induced by PIXE, will be called XRF-PIXE /2.5 MeV protons on Mo primary target/. The same samples were alternatively exposed to protons and X-ray beams. The sensitivities under standard running conditions are determined for both an XRF-PIXE and a PIXE analysis system. It is shown that the sensitivity of the PIXE spectrometer depends strongly on the sample matrix, whereas the XRF-PIXE sensitivity is rather constant with respect to different kinds of samples. In addition, the advantages of one mode of excitation on the other are discussed. It is shown that XRF-PIXE can be a useful complement to PIXE analysis.     

A sequential injection cold-vapor atomic absorption method for the determination of total mercury

A sequential injection (SI) method for the determination of mercury via cold vapor atomic absorption spectrophotometry is presented. The method differs from flow injection (FI) cold vapor methods for the determination of mercury because of the simplicity of the system required for the method: one pump, one valve, a gas-liquid separator, and an atomic absorption spectrophotometer equipped with a quartz cell. Under optimal conditions, the method has the following figures of merit: a linear calibration range of 1.0 to 20 microg L(-1); a detection limit of 0.46 microg L(-1); and a precision of 0.90% RSD (8 microg L(-1)). The procedure allows for a sampling rate of one injection per 80 s (excluding sample pretreatment). Results from the determination of mercury in water and fish specimens are also presented. The figures of merit of the method are compared to two other SI methods for the determination of mercury.     

A sequential injection cold-vapor atomic absorption method for the determination of total mercury

A sequential injection (SI) method for the determination of mercury via cold vapor atomic absorption spectrophotometry is presented. The method differs from flow injection (FI) cold vapor methods for the determination of mercury because of the simplicity of the system required for the method: one pump, one valve, a gas-liquid separator, and an atomic absorption spectrophotometer equipped with a quartz cell. Under optimal conditions, the method has the following figures of merit: a linear ¶calibration range of 1.0 to 20 μg L^–1; a detection limit of 0.46 μg L^–1; and a precision of 0.90% RSD (8 μg L^–1). The procedure allows for a sampling rate of one injection per 80 s (excluding sample pretreatment). Results from the determination of mercury in water and fish specimens are also presented. The figures of merit of the method are compared to two other SI methods for the determination of mercury.     

PIXE analysis of geostandards at the University of Montreal

Four geological standards, BEN, GSN, MRG 1 and SY2 have been analysed using thick target PIXE, and the results are in good agreement with the accepted concentration values for 25 elements. This demonstrates that thick target PIXE analysis employing modern computer codes for data reduction, can be used for fast reliable analysis of geological samples.     

Level of some minor and trace elements in Bangladeshi meat products

An investigation on the level of some minor and trace elements in some varieties of meat (beef, mutton and chicken) consumed in Bangladesh is reported. In this study, protoninduced X-ray emission (PIXE) and radioisotope-induced X-ray fluorescence (XRF) techniques were used for analytical measurements. In PIXE measurements, the samples were exposed to the proton beam in air as 1 mm thick pellets and irradiated with 2.0 MeV protons having the beam intensity of 30 nA for characteristic X-ray excitation, whereas in XRF, the samples were excited for 5000 seconds with a 10 mCi¹⁰⁹Cd annular X-ray source. The elemental concentrations of Ca, Mn, Fe, Ni, Cu, Zn, As, Se, Br, Rb and Sr were determined in the samples by comparison with X-ray yield curves constructed from IAEA and NBS standard reference materials. The significance of the results is dicussed in relation to human health and diseases.This research received financial support from the International Atomic Energy Agency, Vienna, under the research contract RC-4265/RB.     

Electrochemical Detection of Steroid Hormones Using a Nickel‐Modified Glassy Carbon Electrode

This paper demonstrates the development of an analytical method for detecting steroid hormones by coupling HPLC to electrochemical detection, using a nickel‐modified glassy carbon electrode. The method was evaluated in terms of sensitivity, linear dynamic range, limit of detection, and response stability. The developed method exhibited good figures of merit for the steroid hormones studied with no evidence of electrode fouling. As an example, the limit of detection (S/N=3) for E3 was 0.10 µM and the response precision (n=5) was 0.6 %. The application of the method for the analysis of a real river water sample is demonstrated.     

Analytical use of proton-induced X-ray emission

Proton-induced X-ray emission, PIXE, is capable of simultaneous quantitative determination of 10–15 elements. An introduction to the physical properties of the method is given and detection limits are shown for a routine analysis of a thin aerosol sample. Examples of applications to both thick and thin samples are presented. Human tooth dentine is analysed for lead, with simple sample preparation, indicating lead values of a few ppm for Swedish children. Quantitative analyses of several other elements are obtained simultaneously. Cascade impactors are used for sampling aerosols in work environment during welding operations giving information of size distribution and concentrations of the elements present. The aerosol is dominated by particle sizes between 0.5 and 2 μm as measured by the impactor, but the size distributions are different for different elements and welding techniques and depend on the distance from the welding source. The relative abundance of the elements found in the aerosol indicates the presence of fractionation mechanisms.     

Mass spectrometry detection as an innovative and advantageous tool in ligand exchange capillary electrophoresis

The copper(II) complex of a modified cyclodextrin, namely 6-mono-deoxy-6-[4-(2-aminoethyl)imidazolyl]-β-CD (CDmh), previously synthesized and characterized in our laboratory and already used as chiral selector for ligand exchange capillary electrophoresis (LECE) with optical detection, is investigated here in LECE using electrospray-mass spectrometry (ESI-MS) as the detection device. The potential of this hyphenated method is compared with the results previously obtained with optical detection by studying the chiral resolution of tryptophan racemate. Chiral separation conditions compatible with LECE-ESI-MS could be achieved based on the figures of merit obtained by LECE-UV. Interestingly, the values of LOD obtained by LECE-ESI-MS were significantly better than those obtained by LECE-UV and thus, ESI-MS detection seems to open new perspectives in chiral separations by LECE.     

On-line preconcentration and determination of cobalt by chelating microcolumns and flow injection atomic spectrometry

A simple and sensitive flow injection analysis-atomic absorption spectrometric procedure is described for the determination of cobalt. The method is based upon on-line preconcentration of cobalt on a microcolumn of 2-nitroso-1-naphthol immobilized on surfactant coated alumina. The trapped cobalt is then eluted with ethanol (250 μl) and determined by flame atomic absorption spectrometry. The analytical figures of merit for the determination of cobalt are as follows: detection limit (3 S), 0.02 ng ml⁻¹; precision (RSD), 2.8% for 20 ng ml⁻¹ and 1.7% for 70 ng ml⁻¹ of cobalt; enrichment factor, 125 (using 25 ml of sample). The method has been applied to the determination of cobalt in water samples, vitamin B₁₂ and B-complex ampoules and accuracy was assessed through recovery experiment and independent analysis by furnace AAS.     

Direct determination of trans-resveratrol in human plasma by spectrofluorimetry and second-order standard addition

Trans-resveratrol (RVT) is an antioxidant found in red grapes and their derivatives, which has been related to the reduction of cardiovascular diseases and cancer incidence.This work developed a new spectrofluorimetric-chemometric method for the direct determination of RVT in human plasma. For each measurement, excitation-emission matrices were obtained from 280 to 360 nm (excitation) and from 380 to 550 nm (emission). The strategy adopted in this work combined data treatment with parallel factor analysis (PARAFAC), for extracting the pure analyte signal, using the standard addition method, which permits determinations in the presence of a strong matrix effect caused by plasma analyte-protein binding. Plasma samples were diluted 10 times and, for each, four standard additions of RVT were performed, in triplicate. A specific PARAFAC model was built for the three replicates of each sample, from three-way arrays formed by five measurements (initial sample plus four additions), 17 excitation wavelengths and 86 emission wavelengths. The best models were selected with four factors and accounted for more than 99.90% of the data variance. The loadings obtained were related to RVT and three interferences. The scores related to the analyte were used for linear regressions and all standard addition curves presented correlation coefficients equal or greater than 0.99. Good results were obtained in the concentration range from 0.10 to 5.00 μg mL⁻¹, with recoveries between 94.0 and 110.0%. The proposed method was also validated through the estimates of several figures of merit: sensitivity, analytical sensitivity, selectivity, precision, and limits of detection and quantitation.     

Universal screening method for the determination of US Environmental Protection Agency phenols at the lower ng l(-1) level in water samples by on-line solid-phase extraction-high-performance liquid chromatography-atmospheric pressure chemical ionization mass spectrometry within a single run

The applicability of a previously optimized method for the analysis of the US Environmental Protection Agency (EPA) regulations phenols, based on on-line solid-phase extraction coupled to liquid chromatography with mass spectrometric (MS) detection in different matrix loaded water samples is demonstrated. The comprehensive optimization of the mobile phase conditions and their influence on the ionization process in atmospheric pressure ionization is described in detail. In particular, MS detection of the weakly acidic phenols such as phenol, monochlorinated phenols and methylated phenols requires the absence of acidic mobile phase modifiers and buffers. Thus lower retention times and slight peak broadening of the more acidic dinitrophenols are obtained if the entire range of EPA phenols is analyzed within a single chromatographic run. The figures of merit for the method were determined and the applicability to real water samples was investigated. Limits of detection for phenols ranging from 40 to 280 ng l(-1) and relative standard deviations below 8% in SCAN mode are obtained for all phenols if only 10-ml river water samples with low dissolved organic carbon (DOC 5 mg C l(-1) concentrations are preconcentrated. The method was used to detect 2-nitrophenol and 4-nitrophenol in river water samples in the lower ng l(-1) range. The analysis of highly matrix-loaded samples (DOC 210 mg C l(-1)) requires a reduced enrichment volume resulting in decreased sensitivity. Still the method is capable of reaching excellent detection limits which demonstrates its excellent suitability for screening analysis.