纳米碳管负载铂的修饰电极对H2O2的测定

采用嵌入修饰法制得了碳纳米管负载铂修饰的浸蜡石墨电极,结果发现该修饰电极对H2O2的氧化还原都有良好的电催化性能。但对H2O2的还原有更好的催化性能。H2O2的浓度在2.5×10-6~1×10-4mol/L范围内呈现良好的线性关系;检出限为1.26×10-6mol/L。     

Amperometric biosensor for hydrogen peroxide based on coimmobilized horseradish peroxidase and methylene green in ormosils matrix with multiwalled carbon nanotubes

A novel amperometric biosensor for the analytical determination of hydrogen peroxide was developed. The fabrication of the biosensor was based on the coimmobilization of horseradish peroxidase (HRP), methylene green (MG) and multiwalled carbon nanotubes within ormosils; 3-aminopropyltrimethoxysilane (APTMOS), 2-(3,4-epoxycyclohexyl)ethyltrimethoxysilane (ETMOS) and phenyltrimethoxysilane (PHTMOS). APTMOS determined the hydrophilicity/hydrophobicity of the ormosils and PHTMOS and ETMOS increased the physical and mechanical strength of the ormosil matrix. The ormosil modified electrodes were characterized with SEM, UV-vis spectroscopy and electrochemical methods. Cyclic voltammetry and amperometric measurements demonstrated the MG coimmobilized with HRP in this way, displayed good stability and could efficiently shuttle electrons between immobilized enzyme and electrode, and MWCNTs facilitated the electrocatalytic reduction of H₂O₂ at reduced over potential. The Micheaelis constant of the immobilized HRP was 1.8 mM, indicating a high affinity of the HRP to H₂O₂ without loss of enzymatic activity in ormosil matrix. The prepared biosensor had a fast response of H₂O₂, less than 10 s, and excellent linear range of concentration from 5 × 10⁻⁷ to 2 × 10⁻⁵ M with the detection limit of 0.5 μM (S/N = 3) under the optimum conditions. At the same time, the influence of solution pH, effect of enzyme amount, steady-state applied potential and temperature on the biosensor were investigated. The enzyme electrode retained about 90% of its initial activity after 30 days of storage in a dry state at 4 °C. The preparation of the developed biosensor was convenient and showed high sensitivity with good stability.     

A new hydrogen peroxide biosensor based on gold nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film-modified electrode

Gold nanoelectrode ensembles were produced by electrodeposition using multiwalled carbon nanotubes (MWNTs) as template. A new third generation amperometric biosensor for hydrogen peroxide was developed based on adsorption of horseradish peroxidase (HRP) at the glassy carbon (GC) electrode modified with Au nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film. The resulting HRP biosensor offered an excellent detection for hydrogen peroxide at −0.11 V with a linear response range of 2.08 × 10⁻⁷ to 7.6 × 10⁻³ M with a correlation coefficient of 0.998, and response time <5 s. The detection limit was 1.02 × 10⁻⁷ M at 3σ. The biosensor displays rapid response, expanded linear response range, and excellent repeatability. The simple and fast fabrication of the sensor makes it superior to other techniques.     

A novel nonenzymatic hydrogen peroxide sensor based on multi-wall carbon nanotube/silver nanoparticle nanohybrids modified gold electrode

A novel strategy to fabricate hydrogen peroxide (H₂O₂) sensor was developed based on multi-wall carbon nanotube/silver nanoparticle nanohybrids (MWCNT/Ag nanohybrids) modified gold electrode. The process to synthesize MWCNT/Ag nanohybrids was facile and efficient. In the presence of carboxyl groups functionalized multi-wall carbon nanotubes (MWCNTs), silver nanoparticles (Ag NPs) were in situ generated from AgNO₃ aqueous solution and readily attached to the MWCNTs convex surfaces at room temperature, without any additional reducing reagent or irradiation treatment. The formation of MWCNT/Ag nanohybrids product was observed by transmission electron microscope (TEM), and the electrochemical properties of MWCNT/Ag nanohybrids modified gold electrode were characterized by electrochemical measurements. The results showed that this sensor had a favorable catalytic ability for the reduction of H₂O₂. The resulted sensor could detect H₂O₂ in a linear range of 0.05-17 mM with a detection limit of 5 × 10⁻⁷ M at a signal-to-noise ratio of 3. The sensitivity was calculated as 1.42 μA/mM at a potential of −0.2 V. Additionally, it exhibited good reproducibility, long-term stability and negligible interference of ascorbic acid (AA), uric acid (UA), and acetaminophen (AP).     

A highly sensitive hydrogen peroxide amperometric sensor based on MnO2-modified vertically aligned multiwalled carbon nanotubes

In this report, a highly sensitive amperometric sensor based on MnO₂-modified vertically aligned multiwalled carbon nanotubes (MnO₂/VACNTs) for determination of hydrogen peroxide (H₂O₂) was fabricated by electrodeposition. The morphology of the nanocomposite was characterized by scanning electron microscopy, energy-dispersive X-ray spectrometer and X-ray diffraction. Cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy were applied to investigate the electrochemical properties of the MnO₂/VACNTs nanocomposite electrode. The mechanism for the electrochemical reaction of H₂O₂ at the MnO₂/VACNTs nanocomposite electrode was also discussed. In borate buffer (pH 7.8, 0.20 M), the MnO₂/VACNTs nanocomposite electrode exhibits a linear dependence (R = 0.998) on the concentration of H₂O₂ from 1.2 × 10⁻⁶ M to 1.8 × 10⁻³ M, a high sensitivity of 1.08 × 10⁶ μA M⁻¹ cm⁻² and a detection limit of 8.0 × 10⁻⁷ M (signal/noise = 3). Meanwhile, the MnO₂/VACNTs nanocomposite electrode is also highly resistant towards typical inorganic salts and some biomolecules such as acetic acid, citric acid, uric acid and d-(+)-glucose, etc. In addition, the sensor based on the MnO₂/VACNTs nanocomposite electrode was applied for the determination of trace of H₂O₂ in milk with high accuracy, demonstrating its potential for practical application.     

Multi-wall carbon nanotube supported tungsten hexacarbonyl: an efficient and reusable catalyst for epoxidation of alkenes with hydrogen peroxide

Highly efficient epoxidation of alkenes with H₂O₂ catalyzed by tungsten hexacarbonyl supported on multi-wall carbon nanotubes (MWCNTs) modified with 1,2-diaminobenzene is reported. The prepared catalyst, [W(CO)₆@DAB-MWCNT], was characterized by elemental analysis, scanning electron microscopy, FT-IR, and diffuse reflectance UV-Vis spectroscopic methods. The prepared catalyst was applied as an efficient catalyst for green epoxidation of alkenes with hydrogen peroxide in CH₃CN. This heterogeneous metal carbonyl catalyst showed high stability and reusability in epoxidation without loss of its catalytic activity.     

Immobilised cytochrome c on the carbon dots functionalised MWCNTs and its application to hydrogen peroxide detection

We have prepared the carbon dots (C-dots) by sucrose carbonisation in the presence of sulphuric acid and characterised by transmission electron microscopy, Fourier transform infrared spectra, fluorescence spectroscopy and UV–vis absorption spectra. The resultant C-dots could be used for the activation of CNTs. Cytochrome c immobilised on the functionalised multi-walled carbon nanotube-modified glass carbon electrode was found to promote electron transfer that was investigated by electrochemical methods. The obtained electrode can also be used as a biocatalyser to catalyse the reduction of H₂O₂. Under optimal conditions, the constructed H₂O₂ sensor showed two linear segments and the detection limits were 1.02 and 2.59 µM (S/N = 3). The modified electrode displayed high stability, good reproducibility and excellent selectivity.     

Direct electron transfer of glucose oxidase and dual hydrogen peroxide and glucose detection based on water-dispersible carbon nanotubes derivative

A water-dispersible multi-walled carbon nanotubes (MWCNTs) derivative, MWCNTs-1-one-dihydroxypyridine (MWCNTs-Py) was synthesis via Friedel–Crafts chemical acylation. Raman spectra demonstrated the conjugated level of MWCNTs-Py was retained after this chemical modification. MWCNTs-Py showed dual hydrogen peroxide (H₂O₂) and glucose detections without mutual interference by adjusting pH value. It was sensitive to H₂O₂ in acidic solution and displayed the high performances of sensitivity, linear range, response time and stability; meanwhile it did not respond to H₂O₂ in neutral solution. In addition, this positively charged MWCNTs-Py could adsorb glucose oxidase (GOD) by electrostatic attraction. MWCNTs-Py-GOD/GC electrode showed the direct electron transfer (DET) of GOD with a pair of well-defined redox peaks, attesting the bioactivity of GOD was retained due to the non-destroyed immobilization. The high surface coverage of active GOD (3.5 × 10⁻⁹ mol cm⁻²) resulted in exhibiting a good electrocatalytic activity toward glucose. This glucose sensor showed high sensitivity (68.1 μA mM⁻¹ cm⁻²) in a linear range from 3 μM to 7 mM in neutral buffer solution. The proposed sensor could distinguish H₂O₂ and glucose, thus owning high selectivity and reliability.     

Effects of microstructure of carbon nanofibers for amperometric detection of hydrogen peroxide

Carbon nanofibers (CNFs) with three microstructures, including platelet-carbon nanofibers (PCNFs), fish-bone-carbon nanofibers (FCNFs), and tube-carbon nanofibers (TCNFs), were synthesized, characterized, and evaluated for electrochemical sensing of hydrogen peroxide. The CNFs studied here show microstructures with various stacked morphologies. The sizes and graphite-layer ordering of the CNFs can be well controlled. Glassy carbon (GC) electrodes modified by CNFs were fabricated and compared for amperometric detection of hydrogen peroxide. Sensors based on PCNFs/GC, FCNFs/GC, and TCNFs/GC were used in the amperometric detection of H₂O₂ in solution by applying a potential of +0.65 V versus Ag/AgCl at the working electrode. The highest electrocatalytic performance was observed for PCNFs/GC among the three types of hydrogen peroxide sensors. The amperometric response of PCNFs/GC retained over 90% of the initial current of the first day up to 21 days. The linear range is from 1.80 × 10⁻⁴ to 2.62 × 10⁻³ M with a correlation coefficient larger than 0.999 and with a detection limit of 4.0 μM H₂O₂ (S/N = 3). The relative standard deviation for detecting 1.80 × 10⁻⁴ M H₂O₂ (N = 8) is 2.1% with an average response of 0.64 μA. The significant diversity of electrocatalytic activity of the CNFs toward the oxidation of hydrogen peroxide may result from the difference of morphologies, textural properties, and crystalline structures.     

Potentiometric determination of hydrogen peroxide at MnO2-doped carbon paste electrode

A novel hydrogen peroxide (H₂O₂) potentiometric sensor, made with a MnO₂-doped carbon paste electrode (CPE), is reported. Under optimum conditions, the electrode gives a Nernstian response for H₂O₂ in the concentration range 3.00×10⁻⁷–3.63×10⁻⁴ mol/l, with a slope of 21–19.4 mV/pH₂O₂ and a detection limit of 1.2×10⁻⁷mol/l H₂O₂. In addition, this sensor offers some analytical characteristics such as sensitivity, good reproducibility and a simple preparation procedure. The effects of both the components of the electrode and other conditions on the potential response of the sensor, as well as the possible response mechanism, are discussed.     

对甲苯磺酸/活性炭/双氧水体系选择氧化苯乙烯生成苯甲醛(英文)

以双氧水为氧化剂,研究了对甲苯磺酸和活性炭体系选择氧化苯乙烯生成苯甲醛反应性能。考察了反应时间、温度、催化剂用量、苯乙烯和双氧水摩尔比等对苯乙烯选择氧化性能的影响.结果表明,对甲苯磺酸和活性炭的用量和用量比是一个重要因素,但对甲苯磺酸的酸性对氧化反应活性影响不大.对甲苯磺酸和双氧水相互作用,经非自由基过程氧化苯乙烯.通过分解双氧水产生氢氧自由基,活性炭显著提高对甲苯磺酸和双氧水体系氧化苯乙烯活性.在惰性或还原气氛中高温处理活性炭能降低其表面含氧基团数量,增加碱性,有效分解双氧水,产生相对较多的OH自由基.与未处理的活性炭相比,高温处理的活性炭进一步提高了对甲苯磺酸和双氧水体系氧化苯乙烯活性,但降低了苯甲醛选择性.经磺化,在活性炭表面引入的–SO_3H基团比含氧基团(–OH,–COOH)更有效与双氧水作用氧化苯乙烯.     

C60 trianion-mediated electrocatalysis and amperometric sensing of hydrogen peroxide

Heterogeneous electrocatalytic reduction of hydrogen peroxide (H₂O₂) by C₆₀ is reported for the first time. C₆₀ is embedded in tetraoctylammonium bromide (TOAB) film and is characterized by scanning electron microscopy and cyclic voltammetry. Electrocatalytic studies show that the trianion of C₆₀ mediates the electrocatalytic reduction of H₂O₂ in aqueous solution containing 0.1 M KCl. Application of such film modified electrode as an amperometric sensor for H₂O₂ determination is also examined. The sensor shows a fast response within 1 s and a linear response is obtained (R = 0.9986) in the concentration range from 3.33 × 10⁻⁵ to 2.05 × 10⁻³ mol L⁻¹ for H₂O₂, with the detection limit of 2 × 10⁻⁵ mol L⁻¹ and the sensitivity of 1.65 μA mM⁻¹. A good repeatability and stability is shown for the sensor during the experiment.     

Nonenzymatic amperometric sensor of hydrogen peroxide and glucose based on Pt nanoparticles/ordered mesoporous carbon nanocomposite

A simple and facile synthetic method to incorporate Pt nanoparticles inside the mesopores of ordered mesoporous carbons (OMCs) is reported. The Pt/OMCs nanocomposite was characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and nitrogen adsorption-desorption. The results show that the incorporation of Pt nanoparticles inside the pores of OMCs does not change the highly ordered two-dimensional hexagonal mesostructure of OMCs matrix. Nonenzymatic amperometric sensor of hydrogen peroxide and glucose based on the Pt/OMCs nanocomposite-modified glassy carbon (GC) electrode is developed. Compared with the original OMCs-modified electrode, the Pt/OMCs-modified electrode displays improved current response towards hydrogen peroxide and gives linear range from 2 to 4212 μM. At an applied potential of −0.08 V, the Pt/OMCs nanocomposite gives linearity in the range of 0.5-4.5 mM glucose in neutral buffered saline solution. This glucose sensor also exhibits good ability of anti-interference to electroactive molecules. The combination the unique properties of Pt nanoparticles and the ordered mesostructure of OMCs matrix guarantees the enhanced response for hydrogen peroxide and glucose.     

Multilayer films of carbon nanotubes and redox polymer on screen-printed carbon electrodes for electrocatalysis of ascorbic acid

Multilayer films containing multiwall carbon nanotubes and redox polymer were successfully fabricated on a screen-printed carbon electrode using layer-by-layer (LBL) assembled method. UV-vis spectroscopy, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy and electrochemical method were used to characterize the assembled multilayer films. The multilayer films modified electrodes exhibited good electrocatalytic activity towards the oxidation of ascorbic acid (AA). Compared with the bare electrode, the oxidation peak potential negatively shifted about 350 mV (versus Ag/AgCl). Furthermore, the modified screen-printed carbon electrodes (SPCEs) could be used for the determination of ascorbic acid in real samples.     

Study on electrochemical behavior of tryptophan at a glassy carbon electrode modified with multi-walled carbon nanotubes embedded cerium hexacyanoferrate

Electrochemical behavior of cerium hexacyanoferrate (CeHCF) incorporated on multi-walled carbon nanotubes (MWNTs) modified GC electrode is investigated by scanning electron microscopy (SEM) and electrochemical techniques. The CeHCF/MWNT/GC electrode showed potent electrocatalytic activity toward the electrochemical oxidation of tryptophan in phosphate buffer solution (pH 7.0) with a diminution of the overpotential of 240 mV. The anodic peak currents increased linearly with the concentration of tryptophan in the range of 2.0 × 10⁻⁷ to 1.0 × 10⁻⁴ M with a detection limit of 2.0 × 10⁻⁸ M (at a S/N = 3). And the determination of tryptophan in pharmaceutical samples was satisfactory.     

Bleaching of cellulose by hydrogen peroxide

Peroxides are important bleaching agents, industrially, for cellulosic products. They are also used in detergents. Peroxides can degrade cellulose as well as decolorize it and remove stains. Both free radicals and perhydroxyl anions have been suggested as the intermediates in the reactions occurring between cellulosic products and hydrogen peroxide. The proposed mechanisms are reviewed with emphasis primarily on cotton cellulose. Further work is required to establish unequivocally the mechanism of degradation and decolorization of cellulose products.     

A sensitive amperometric sensor for hydrazine and hydrogen peroxide based on palladium nanoparticles/onion-like mesoporous carbon vesicle

Onion-like mesoporous carbon vesicle (MCV) with multilayer lamellar structure was synthesized by a simply aqueous emulsion co-assembly approach. Palladium (Pd) nanoparticles were deposited on the MCV matrix (Pd/MCV) by chemical reduction of H₂PdCl₄ with NaBH₄ in aqueous media. Pd(X)/MCV (X wt.% indicates the Pd loading amount) nanocomposites with different Pd loading amount were obtained by adjusting the ratio of precursors. The particular structure of the MCV results in efficient mass transport and the onion-like layers of MCV allows for the obtainment of highly dispersed Pd nanoparticles. The introduction of Pd nanoparticles on the MCV matrix facilitates hydrazine oxidation at more negative potential and delivers higher oxidation current in comparison with MCV. A linear range from 2.0 × 10⁻⁸ to 7.1 × 10⁻⁵ M and a low detection limit of 14.9 nM for hydrazine are obtained at Pd(25)/MCV nanocomposite modified glassy carbon (GC) electrode. A nonenzymatic amperometric sensor for hydrogen peroxide based on the Pd(25)/MCV nanocomposite modified GC electrode is also developed. Compared with MCV modified GC electrode, the Pd(25)/MCV nanocomposite modified GC electrode displays enhanced amperometric responses towards hydrogen peroxide and gives a linear range from 1.0 × 10⁻⁷ to 6.1 × 10⁻³ M. The Pd(25)/MCV nanocomposite modified GC electrode achieves 95% of the steady-current for hydrogen peroxide within 1 s. The combination of the unique properties of Pd nanoparticles and the porous mesostructure of MCV matrix guarantees the improved analytical performance for hydrazine and hydrogen peroxide.     

Grape tissue-based electrochemical sensor for the determination of hydrogen peroxide

The use of grape tissue as a source of catalase for the determination of hydrogen peroxide is reported. A slice of grape tissue attached to the membrane of a Clark-type oxgen sensor was used to monitor the oxidation of hydrogen peroxide by catalase. At the steady state, the sensor responds linearly to hydrogen peroxide in the concentration range 1 × 10^?5–5 × 10^?4 M. The response time (T₉₀) was of the order of 1 min for this sensor. No interference was observed from ethanol, amino acids, glucose and lactic acid. The long-term stability of the grape tissue sensor was much better than previously reported immobilized enzyme and liver tissue-based hydrogen peroxide sensors.     

氮掺杂碳包埋钴纳米粒子电催化合成过氧化氢

电催化还原氧是一种新兴的可持续生产过氧化氢(H2O2)的合成技术,寻找低成本、高活性和高选择性的电催化剂是该技术实际应用的关键.钴氮掺杂的碳材料因含有钴氮(Co-Nx)催化活性位,成为一类新兴的可促进H2O2电化学合成的材料.本文采用低能耗干式球磨外加控制热解的方法来制备包含许多Co-Nx结构的钴氮掺杂碳材料.该方法使用材料廉价,即将醋酸钴、2-甲基咪唑和Ketjenblack EC-600JD高纯度且导电的碳黑分别作为金属、氮和碳的前体.在酸性介质中的电化学测试结果表明,该材料的氧还原反应电流密度明显增加,同时起始电位向正方向移动.该催化剂在较大电位范围内对H2O2的选择性约为90％.H2O2整体电解实验表明,H2O2产率达到100mmol gcat?1 h?1,H2O2法拉第效率达到85％(0.3Vvs.RHE条件下2h).耐久性测试(在0.3Vvs.RHE条件下6h)表明,催化剂表现出相对稳定的性能,且在整个测试循环中,法拉第效率达到约85％,表明催化剂在实际应用中具有良好的耐久性.催化剂表现出较高的电催化合成H2O2活性和选择性可能是由于形成了Co-Nx活性位,以及酸性环境和应用电位等其它因素的影响.     

氮掺杂碳包埋钴纳米粒子电催化合成过氧化氢

电催化还原氧是一种新兴的可持续生产过氧化氢(H2O2)的合成技术,寻找低成本、高活性和高选择性的电催化剂是该技术实际应用的关键.钴氮掺杂的碳材料因含有钴氮(Co-Nx)催化活性位,成为一类新兴的可促进H2O2电化学合成的材料.本文采用低能耗干式球磨外加控制热解的方法来制备包含许多Co-Nx结构的钴氮掺杂碳材料.该方法使用材料廉价,即将醋酸钴、2-甲基咪唑和Ketjenblack EC-600JD高纯度且导电的碳黑分别作为金属、氮和碳的前体.在酸性介质中的电化学测试结果表明,该材料的氧还原反应电流密度明显增加,同时起始电位向正方向移动.该催化剂在较大电位范围内对H2O2的选择性约为90％.H2O2整体电解实验表明,H2O2产率达到100mmol gcat?1 h?1,H2O2法拉第效率达到85％(0.3Vvs.RHE条件下2h).耐久性测试(在0.3Vvs.RHE条件下6h)表明,催化剂表现出相对稳定的性能,且在整个测试循环中,法拉第效率达到约85％,表明催化剂在实际应用中具有良好的耐久性.催化剂表现出较高的电催化合成H2O2活性和选择性可能是由于形成了Co-Nx活性位,以及酸性环境和应用电位等其它因素的影响.