[(Fe/Pt/Fe)/Ag]n多层膜低温合成分离的L10相FePt纳米颗粒

制备了［（Fe/Pt/Fe）/Ag］n多层膜,研究了不同温度退火后的微结构和磁特性.实验结果表明温度高于400℃退火后,样品开始形成L10相的FePt纳米颗粒与Ag基体的复合结构.ΔM曲线的测量表明FePt颗粒之间不存在交换作用,非常清楚地说明非磁基体Ag有效地隔离了FePt磁性颗粒.有序相的低温合成可能和多层膜结构所造成的界面扩散以及Ag层引入的界面缺陷有关,同时,Ag原子较强的迁移性以及FePt与Ag之间表面自由能的显著差异,使FePt纳米颗粒被Ag隔离. 关键词： L10相 FePt 交换作用     

利用FePt/Au多层膜结构制备垂直磁记录L10-FePt薄膜

利用磁控溅射方法在100℃的MgO单晶基片上制备了［FePt/Au］₁₀多层膜,并研究了采用FePt/Au多层膜结构对FePt薄膜的有序化温度、矫顽力（H_C）、垂直磁各向异性、晶粒尺寸以及颗粒间磁交换耦合作用的影响.磁性测试结果表明：FePt/Au多层膜在退火后具有较高的H_C、良好的垂直磁各向异性、较小的晶粒尺寸且无磁交换耦合作用.截面高分辨电镜分析表明：Au可以缓解MgO和FePt之间较大的晶格错配,从而促进薄 关键词： 0-FePt薄膜')" href="#">L1₀-FePt薄膜 有序化温度 垂直磁各向异性 磁交换耦合作用     

室温生长MgO底层诱导(001)取向FePt薄膜的有序化过程对FePt成分的依赖

室温下通过磁控溅射在表面热氧化的Si基片上生长了MgO/Fe_xPt_100-x双层膜和Fe_xPt_100-x单层膜系列样品，Fe_xPt_100-x的原子成分x=48—68.研究了热处理前后不同成分FePt薄膜的晶体结构和磁性的变化，尤其是MgO底层的引入对FePt的晶体结构和磁性的影响 关键词： FePt(001)薄膜 0相')" href="#">L1₀相     

[(Fe/Pt/Fe)/Ag]n多层膜低温合成分离的L10相FePt纳米颗粒

制备了[(Fe/Pt/Fe)/Ag]n多层膜,研究了不同温度退火后的微结构和磁特性.实验结果表明温度高于400℃退火后,样品开始形成L10相的FePt纳米颗粒与Ag基体的复合结构.△M曲线的测量表明FePt颗粒之间不存在交换作用,非常清楚地说明非磁基体Ag有效地隔离了FePt磁性颗粒.有序相的低温合成可能和多层膜结构所造成的界面扩散以及Ag层引入的界面缺陷有关,同时,Ag原子较强的迁移性以及FePt与Ag之间表面自由能的显著差异,使FePt纳米颗粒被Ag隔离.     

氧化物隔离对Si基片上生长L1_0相FePt薄膜磁性的影响

用MgO和SiO_2两种氧化物将FePt薄膜与Si(100)基片隔离,分析隔离层在FePt层发生A1→L1_0转变过程中的作用,寻找用Si母材涂敷L1_0-FePt磁性层来提高磁力显微镜针尖矫顽力的合理方案.采用磁控溅射法在400?C沉积Fe Pt薄膜,在不同温度进行2 h的真空热处理,分析晶体结构和磁性的变化.结果表明:没有隔离层,Si基片表层容易发生扩散,50 nm厚FePt薄膜的矫顽力最大只有5kOe(1 Oe=10~3/(4π)A·m~(-1));而插入隔离层,矫顽力可以超过10 kOe;MgO在Si基片上容易碎裂,热处理温度不能高于600?C,用作隔离层,FePt的最大矫顽力为12.4 kOe;SiO_2与Si基片的晶格匹配更好,热膨胀系数差较小,能承受的最高热处理温度可以超过800?C,使得Fe Pt的矫顽力可以在5 kOe到15 kOe范围内调控,更适合用于制作矫顽力高并可控的磁力显微镜针尖.     

Bi底层对FePt薄膜的影响

利用磁控溅射的方法，在玻璃基片上制备了以Bi为底层的FePt薄膜，经不同温度真空热处理得到L1₀-FePt薄膜.研究了Bi做底层对FePt薄膜的有序化温度及矫顽力H_c的影响.实验结果表明：以Bi做底层的FePt薄膜在350℃实现低温有序，同时其H_c也有大幅度提高，并且可以在更大成分范围内获得H_c较高的L1₀-FePt薄膜.利用X射线光电子能谱研究了薄膜中Bi原子的分布情况，利用X射线衍射研究了薄膜的晶体学结构变化.结果表明,Bi底层在退火过程中的扩散促进了FePt薄膜有序度的升高. 关键词： 0-FePt薄膜')" href="#">L1₀-FePt薄膜 有序化温度 底层 扩散     

利用FePt/Au多层膜结构制备垂直磁记录L10-FePt薄膜

利用磁控溅射方法在100℃的MgO单晶基片上制备了[FePt/Au]10多层膜,并研究了采用FePt/Au多层膜结构对FePt薄膜的有序化温度、矫顽力(HC)、垂直磁各向异性、晶粒尺寸以及颗粒间磁交换耦合作用的影响.磁性测试结果表明:FePt/Au多层膜在退火后具有较高的HC、良好的垂直磁各向异性、较小的晶粒尺寸且无磁交换耦合作用.截面高分辨电镜分析表明:Au可以缓解MgO和FePt之间较大的晶格错配,从而促进薄膜的垂直磁各向异性;同时,采用FePt/Au多层膜结构增加了FePt/Au界面能、应力能以及Au原子在薄膜中的扩散作用,促进了薄膜的有序化,从而有效降低了有序化温度,并且大幅度提高其HC.此外,Au原子部分扩散到FePt相的边界处,起到抑制FePt晶粒生长、隔离FePt颗粒的作用,从而显著降低了FePt晶粒的尺寸和颗粒间磁交换耦合作用.     

微观相场法模拟Ni75Al5.3V19.7 中L12和D022结构反位缺陷的演化

运用微观相场法研究Ni₇₅Al_5.3V_19.7合金沉淀过程中L1₂结构和D0₂₂结构反位缺陷发现：在沉淀初期,L1₂结构反位缺陷Al_Ni,V_Ni,Ni_Al,D0₂₂结构反位缺陷V_Ni,Al_Ni关键词： 微观相场 反位缺陷 L1₂结构')" href="#">L1₂结构 D0₂₂结构')" href="#">D0₂₂结构     

利用［Fe/Pt］n多层膜降低L10-FePt有序化温度

采用直流磁控溅射方法制备了Fe/Pt多层膜和FePt单层薄膜，再经不同温度真空热处理得到 了有序相L10₀-FePt薄膜.通过x射线衍射谱和磁性研究表明，FePt单层薄膜需 要在500℃ 以上热处理，才能开始有序化转变，而Fe/Pt多层膜可以降低FePt薄膜有序化温度.［Fe(1 5nm)/Pt(15nm)］13₁₃薄膜在350℃热处理后，有序度已经增加到 06，相应矫 顽力达到了501kA/m.多层膜化促进有序化在较低的温度下进行，这是由于热处理过程中多 关键词： 0-FePt有序相')" href="#">L10₀-FePt有序相 磁控溅射 有序度 Fe/Pt多层膜     

Cu掺杂对FexPt1－x薄膜有序化的影响

利用磁控溅射制备了薄膜厚度为50nm的系列(Fe_xPt_1-x)_100-yCu_y(x=0.46—0.56,y=0,0.04,0.12) 样品.利用直流共溅射方法精确控制Fe和Pt的原子比.实验结果表明，当x>0.52时，样品中添加Cu不能促进FePt的有序化，但是对于FePt化学原子定比或富Pt的样品，添加Cu可以促进FePt有序化，而且随着Fe含量的减少，需要更多的Cu添加才能实现较低温度下FePt薄膜的有序化.实验结果表明，原子比(FeCu)/Pt达到1.1—1.2的范围时，即可实现较低温度的有序化. 关键词： 0-FePt有序相')" href="#">L1₀-FePt有序相 磁控溅射 有序度 Cu掺杂     

Amorphous Ni-Al underlayer-accelerated L10 ordering transition of FePt thin films

In the present study, we succeeded in accelerating the L1₀ ordering transition of FePt thin films by employing amorphous Ni-Al as underlayers. The coercivity H_c = 5 kOe and ordering parameter S = 0.67 of FePt thin films deposited on a Ni-Al underlayer with a thickness of ∼5 nm after 380 °C annealing for 30 min are significantly higher than those H_c = 0.4 kOe and S = 0.35 of the films without the Ni-Al underlayer. The L1₀ ordering process of and the coercivity of FePt thin films can be significantly tuned by varying the thickness of the Ni-Al underlayer.     

A comparison of FePt thin films with HfO2 or MnO additive

The influence of oxide additives on the magnetic and structural properties of FePt L1₀ thin films has been studied. FePt films with HfO₂ additive grown on a 5 nm MgO buffer showed a primarily random texture for both as-deposited and annealed samples. The average grain size was limited to 10 nm and the perpendicular coercivity was 1.3 kOe for a 10 nm thick FePt +20% HfO₂ film annealed at 650°C for 10 min. In direct contrast, MnO additive neither limited grain size nor L1₀ ordering in annealed FePt films. A 10 nm thick FePt+20% MnO film grown on a 5 nm MgO buffer showed a unique discontinuous microstructure composed of clusters of (0 0 1) textured L1₀ grains after being annealed at 650°C for 10 min. The average size of the grains making up these clusters was 50 nm and the perpendicular coercivity of the film exceeded 7 kOe.     

Composition influence on the microstructures and magnetic properties of FePt thin films

The Fex Pt 100x (10nm) (x=31-51) thin films are fabricated on Si (100) substrates by using magnetron sputtering. The highly ordered L1 0 FePt phase is obtained after post-annealing at 700℃in Fe 47 Pt 53 thin film. The sample shows good perpendicular anisotropy with a square loop and a linear loop in the out-of-plane and the in-plane direction, respectively. The variations of the magnetic domains are investigated in the films when the content value of Fe changes from 31% to 51%.     

Ll_0 FePt thin films with 001crystalline growth fabricated by ZnO addition and rapid thermal annealing

FePt films with a high degree of order S of the L1 0 structure (S 0.90) and well defined 001crystalline growth perpendicular to the film plane are fabricated on thermally oxidized Si substrates by the addition of ZnO and a successive rapid thermal annealing (RTA) process. The optimum condition to prepare high-ordering L1 0 FePtZnO films is 20 vol% ZnO addition and 450℃annealing. The effect of the ZnO additive on the ordering process of the L1 0 FePtZnO films is discussed. In the annealing process, Zn atoms move to the film surface and evaporate. The motion of the Zn atoms accelerates the intergrain exchange and decreases the ordering temperature.     

As-grown preparation of FePt-ordered alloy thin films from Pt/Fe bi-layered structure

A novel method to fabricate FePt-ordered alloy thin films with (0 0 1) preferential orientation from Pt/Fe bi-layered films has been developed. It is able to omit post-annealing with a furnace, and the whole process can be conducted in a chamber without exposing samples to air. In this method, the inter-diffusion and the hetero-epitaxial relation between Fe and Pt are key factors to attain an FePt-ordered alloy thin film with (0 0 1) preferential orientation. An FePt-ordered alloy thin film with (0 0 1) preferential orientation fabricated from Pt[3 nm]/Fe[3 nm] bi-layer employing this method exhibited a relatively large coercivity of 5.6 kOe and high squareness ratio of 0.94 on perpendicular magnetization property. This novel method has a potential to fabricate FePt-based perpendicular magnetic recording media more easily than several conventional methods.     

L lo FePt thin films with [001] crystalline growth fabricated by ZnO addition and rapid thermal annealing

FePt films with a high degree of order S of the L10 structure （S 〉 0.90） and well defined [001] crystalline growth perpendicular to the film plane are fabricated on thermally oxidized Si substrates by the addition of ZnO and a successive rapid thermal annealing （RTA） process. The optimum condition to prepare high-ordering L10 FePtZnO films is 20 vol% ZnO addition and 450 ℃ annealing. The effect of the ZnO additive on the ordering process of the L10 FePtZnO films is discussed. In the annealing process, Zn atoms move to the film surface and evaporate. The motion of the Zn atoms accelerates the intergrain exchange and decreases the ordering temperature.     

Very high coercivities of top-layer diffusion Au/FePt thin films

The Au/FePt samples were prepared by depositing a gold cap layer at room temperature onto a fully ordered FePt layer, followed by an annealing at 800 °C for the purpose of interlayer diffusion. After the deposition of the gold layer and the high-temperature annealing, the gold atoms do not dissolve into the FePt Ll₀ lattice. Compared with the continuous FePt film, the TEM photos of the bilayer Au(60 nm)/FePt(60 nm) show a granular structure with FePt particles embedded in Au matrix. The coercivity of Au(60 nm)/FePt(60 nm) sample is 23.5 kOe, which is 85% larger than that of the FePt film without Au top layer. The enhancement in coercivity can be attributed to the formation of isolated structure of FePt ordered phase.     

c轴垂直取向FePt薄膜的磁和磁光性能研究

采用直流磁控溅射的方法在氧化镁(100)单晶基板上生长了一系列c轴垂直取向的FePt薄膜，通过改变沉积时的基板温度，薄膜从Fe，Pt原子无序排列的面心立方结构逐渐变化到有序排列的L1₀相面心四方结构.在此基础上，系统研究了FePt薄膜的化学有序度对磁和磁光性能的影响.随着有序度的增加，FePt薄膜的磁晶各向异性能，以及沿垂直方向的矫顽力、剩磁比均增加，在基板温度高于530 ℃时制备的薄膜中的磁晶各向异性能超过1 J/cm³.同时，还观察到有序FePt合金薄膜的磁光克尔光谱(克尔转角的大小和极值所对应的跃迁光子能量)随化学有序度的显著变化. 关键词： FePt薄膜 化学有序度参数 磁光克尔光谱     

CoPt(FePt)-C纳米复合膜的结构与磁性

用磁过滤脉冲真空电弧沉积方法制备了CoPt(FePt) C纳米复合薄膜，并在不同温度下进行了退火处理，研究了薄膜中碳的含量以及退火温度对薄膜结构与磁性能的影响.制备态薄膜经过足够高的温度退火后，x射线衍射和磁力显微镜分析发现，在碳基质中生成了面心四方相的CoPt(FePt)纳米颗粒.对于特定组分为Co24Pt31C45和Fe43Pt35C22的薄膜，矫顽力以及颗粒尺寸都随退火温度的升高而增大，当退火温度为700℃时，Co24Pt31C45薄膜的矫顽力为21×105A/m，晶粒尺寸为17nm;当退火温度为650℃时，Fe43Pt35C22相应值分别为28×105A/m和105nm. 关键词： 磁记录材料 磁性薄膜 CoPt FePt纳米复合薄膜