Determination of trace amounts of vanadium by UV-vis spectrophotometric after separation and preconcentration with modified natural clinoptilolite as a new sorbent

Natural clinoptilolite was used as a sorbent material for solid phase extraction and preconcentration of vanadium. The clinoptilolite was first saturated with a cation such as nickel(II) and then modified with benzyldimethyltetradecyleammonium chloride (BDTA) for increasing sorption of 4-(2-pyridylazo)resorcinol (PAR). Vanadium–PAR complex was quantitatively retained on the sorbent by the column method at the pH range 6.2–7.0 at a flow rate of 1 mL min⁻¹. It was removed from the column with 5.0 mL of dimethylformamide solution at a flow rate of 0.8 mL min⁻¹ and determined by UV–vis spectrophotometry at λ_max = 550 nm. 0.031 μg of vanadium can be concentrated from 450 mL of aqueous sample (where detection limit as 0.07 ng mL⁻¹ with preconcentration factor of 90). Relative standard deviation for eight replicate determination of 5.0 μg of vanadium in final solution is 2.1%. The interference of number of anions and cations has been studied in detail to optimize the conditions and method was successfully applied for determination of all vanadium as V(IV) form in standard samples.     

Spectrophotometric method for determination of vanadium and its application to industrial, environmental, biological and soil samples

The very sensitive, fairly selective direct spectrophotometric method for the determination of trace amount of vanadium (V) with 1,5-diphenylcarbohydrazide (1,5-diphenylcarbazide) has been developed. 1,5-diphenylcarbohydrazide (DPCH) reacts in slightly acidic (0.0001–0.001 M H₂SO₄ or pH 4.0–5.5) 50% acetonic media with vanadium (V) to give a red–violet chelate which has an absorption maximum at 531 nm. The average molar absorption coefficient and Sandell’s sensitivity were found to be 4.23×10⁴ l mol⁻¹ cm⁻¹ and 10 ng cm⁻² of V^v, respectively. Linear calibration graph were obtained for 0.1–30 μg ml⁻¹ of V^v: the stoichiometric composition of the chelate is 1:3 (V: DPCH). The reaction is instantaneous and absorbance remain stable for 48 h. The interference from over 50 cations, anions and complexing agents has been studied at 1 μg ml⁻¹ of V^v. The method was successfully used in the determination of vanadium in several standard reference materials (alloys and steels), environmental waters (potable and polluted), biological samples (human blood and urine), soil samples, solution containing both vanadium (V) and vanadium (IV) and complex synthetic mixtures. The method has high precision and accuracy (s=±0.01 for 0.5 μg ml⁻¹).     

Calibration by the gradient ratio-standard addition method in flow injection flame atomic absorption spectrometry

A calibration method has been developed which is realised in the flow injection analysis (FIA) by the gradient technique. According to this method two transient peaks, one for a sample and the other for a sample with standard addition, are recorded and compared point by point in the entire defined time range. The analytical result is estimated on the basis of information gained about the local analyte concentrations in the sample zone. The method allows the results to be reliable when both the non-linear calibration dependence and the interference effect occur. As an example, calcium in synthetic samples containing silicon, phosphate, aluminium, vanadium and titanium, and also in iron ore sample, were determined by flame atomic absorption spectrometry (FAAS). It has been proved, that the method can be effective in overcoming even extremely strong interferences, providing analytical results with average accuracy equal to ca. 5% and with precision 2–3 times inferior to that obtained by conventional FI calibration.     

Simultaneous spectrophotometric determination of iron and vanadium by H-point standard addition method and partial least squares regression in micellar medium

Simultaneous determination of total iron and vanadium by H-point standard addition method (HPSAM) and partial least squares (PLS) is described. Gallic acid (GA) in a cationic micellar solution of CTAB was used for determination of iron and vanadium in different oxidation states at pH 5. The presence of a micellar system enables total iron and vanadium to be determined with improved sensitivities. The total relative standard error for applying the PLS method to 15 synthetic samples in the ranges 0.20–15.00 μg ml⁻¹ iron and 0.20–8.00 μg ml⁻¹ vanadium was 2.2%. The results of applying the H-point standard addition method showed that iron and vanadium can be determined simultaneously with the concentration ratios of iron to vanadium from 10:1 to 1:20 in the mixed sample. Both HPSAM and PLS methods showed suitable abilities to resolve accurately overlapped absorption spectra of the compounds. Both proposed methods were successfully applied to the determination of Fe and V in several synthetic alloy solutions.     

A novel method for the spectrophotometric determination of nitrite in water

A rapid, simple, selective and sensitive method for the spectrophotometric determination of nitrite in water has been developed and optimum reaction conditions along with other analytical parameters have been evaluated. Nitrite reacts with barbituric acid in acidic solution to give the nitroso derivative, violuric acid. At analytical wavelength of 310 nm, Beer's law is obeyed over the concentration range 0.00–3.22 ppm of nitrite. The molar absorptivity is 15330 ± 259.7 (95%) with pooled standard deviation of 355.57 and R.S.D. of 2.32%. As well as the method is sensitive (2.99 × 10⁻³ μg NO₂ cm⁻²) and selective, it tolerates most of the potential interferents. It has been successfully applied to nitrite determination in natural waters by use of a calibration graph with determination limit of 1.66 μg NO₂ in 100 mL working solution corresponding to minimum 9.5 ppb NO₂–N in water samples. Lower concentrations of nitrite (3.0 μg NO₂/L sample) is precisely analyzed by using the method of dilution with sample, with R.S.D. of lower than 0.5%. The results were compared with standard N-(1-naphtyl)ethylenediamine dihydrochloride method and very good agreement between the data was observed. The method can easily be applied in the field.     

Direct determination of germanium in botanical samples by graphite furnace atomic absorption spectrometry with palladium-zirconium as chemical modifier

A method has been described for the direct determination of trace levels of germanium by graphite furnace atomic absorption spectrometry (GFAAS) using chemical matrix modification technique. The stabilization and the pyrolysis temperatures for germanium were investigated with various chemical modifiers including palladium, palladium–magnesium, palladium–strontium and palladium–zirconium. The highest pyrolysis temperature and highest integrated absorbance were obtained using palladium–zirconium modifier, and the severe matrix interference from sulfate can be eliminated. The characteristic mass and absolute detection limit (3σ) of germanium were found to be 16 and 12 pg, respectively. The proposed method was applied to the determination of trace levels of germanium in botanical samples with a recovery range of 92–106%. The hydride generation atomic fluorescence spectrometric (HGAFS) method was employed to analyze the samples and the results agree well with those obtained by GFAAS. The contents of germanium in standard reference materials were determined and the results were in good agreement with the reference values.     

Determination of soluble phosphates in water samples using ytterbium(III) and dynamic measurements of light scattering intensity at long wavelength

A selective and fast method has been developed for the determination of phosphates by measuring the formation of ytterbium(III) phosphate through the variation of the light scattering intensity with time. The low solubility of this compound causes an efficient dispersion of the radiation at 490 nm, which is measured at 980 nm using the second-order grating effect. This approach minimizes potential background signals from the sample matrix. The initial rate of the system is automatically obtained in only 0.5 s by stopped-flow mixing technique. The variable optimization study has been carried out using univariate and multivariate methods. The dynamic range of the calibration graph is 0.09–7.9 mmol L⁻¹ (Pearson's correlation coefficient = 0.9999) and the detection limit is 0.03 mmol L⁻¹. The precision of the method, expressed as relative standard deviation, is 2.3%. The study of the potential interference of different inorganic anions showed that arsenate is the main interferent, although it is tolerated in a molar ratio of 5.5. The method has been satisfactorily applied to the determination of soluble phosphates in tap, ground and river water using a previous preconcentration step with a Dowex 1 (1 × 4–400) anionic resin. A 500-fold concentration has been achieved, which has allowed to decrease the detection limit up to 60 mmol L⁻¹. The recovery range is 97.5–102.5%. The results obtained are consistent with those obtained with the standard molybdenum blue method.     

Fluorimetric flow injection analysis of trace amount of formaldehyde in environmental atmosphere with 5,5-dimethylcyclohexane-1,3-dione

A simple and sensitive flow injection method with fluorimetry and 5,5-dimethylcyclohexane-1,3-dione (dimedone) was developed for the determination of formaldehyde. Formaldehyde reacted with dimedone in the presence of ammonium acetate to form a fluorescence compound, which has an excitation wavelength at 395 nm and an emission wavelength at 463 nm. A two-channel flow system was assembled. Distilled water and 0.3% dimedone buffered at pH 5.5 were delivered at 0.7 ml min⁻¹ and 100 μl of sample was injected into the carrier stream. The reaction was done in the reaction system designed newly, which consists of heating and cooling devices. The chemical reactivity with formaldehyde was excellent in the reaction system and selective. The calibration graphs were linear in the range of 25–100 and 5–10 ppb. RSDs (n=10) for 50 and 10 ppb formaldehyde were 0.6 and 3.4% and the LOD (S/N=3) was 0.9 ppb. The sample throughput was 20 h⁻¹. The method was applied to the determination of formaldehyde in gas sample evolved from adhesive agents and in living environmental indoor. The sensitive and selective method is useful for monitoring trace of formaldehyde in the environmental atmosphere.     

Catalytic flow injection determination of vanadium by oxidation of N-(3-sulfopropyl)-3,3',5,5'-tetramethylbenzidine using bromate

A catalytic flow-injection (FI) method was developed for the determination of 10⁻⁹ mol l⁻¹ levels of vanadium(IV, V). The method is based on the catalytic effect of vanadium(V) on oxidation of N-(3-sulfopropyl)-3,3′,5,5′-tetramethylbenzidine (TMBZ·PS) using bromate as oxidant to form a yellow dye (λ_max=460 nm). The use of 5-sulfosalicylic acid (SSA) as an activator enhanced the sensitivity of the method. The calibration graphs with a working range 0.05–8.0 ng ml⁻¹ were obtained for vanadium(V). Vanadium(IV) was also determined, being oxidized by bromate. The detection limit (signal/noise, S/N=3) was 0.01 ng ml⁻¹ (ca. 2×10⁻¹⁰ mol l⁻¹) vanadium. The relative standard deviations (R.S.D.) for 15 determinations of 0.5 ng ml⁻¹ vanadium, and for ten determinations of 0.1 and 1.0 ng ml⁻¹ vanadium were 0.41, 2.6 and 0.25%, respectively, with a sampling rate of 15 samples h⁻¹. The proposed method was successfully applied to the determination of vanadium in natural waters.     

Activation analysis of vanadium in high alloy steels using manganese as internal standard

A method has been developed for the determination of vanadium in high alloy steels by radioactivation analysis. Manganese present in the steel sample is used as an internal standard, thus permitting accurate correction of neutron flux irregularities between sample and reference. The method was tested on 4 National Bureau of Standard samples having a vanadium content from 0.014 up to 2.04% and a widely differing composition as regards other alloy constituents. The results obtained by radioactivation in the Belgian Reactor BRI and the Amsterdam 28 MeV deuteron cyclotron show satisfactory accuracy as well as precision.     

Development of a new method for the separation of vanadium species and chloride interference removal using modified silica capillaries-DIN-ICP-MS

A new on-line method for the separation of vanadium (IV) and vanadium (V) as well as for the removal of ClO⁺ mass spectral interference on vanadium determination by quadrupole-ICP-MS has been developed. The sample introduction system consists of a modified fused silica capillary coupled to a direct injection nebuliser (DIN), between the solvent delivery system and the ICP. Fused silica capillaries were treated with different anion and cation exchanger reagents and were tested for the retention of Cl⁻ and the separation of vanadium ions at μg l⁻¹ levels. A suitable strong anion exchanger functional group (3-aminopropyltrimethoxy silane) was selected. Chlorine anions were retained in this anionic capillary and the separation between V(IV) and V(V) was possible in the pH range 2–4. The selections of instrumental ICP-MS conditions for the minimisation of the ClO+ interference were carefully considered. Factors affecting the chromatographic separation such as sample pH, sample flow rate, effect of methanol in the mobile phase and length of the capillary for the separation were optimised. The proposed methodology provides a simple and rapid method for vanadium speciation. A relative detection limit of 12 l⁻¹ (i.e. absolute detection limits of 120 pg) for V(IV) based on peak height measurements was obtained. The relative standard deviation for V(IV) was 2.4% for a 10 μl injection (n=6).     

Determination of chloride ion in aqueous samples by isotope-dilution Fourier-transform flame infrared emission (ID-FIRE) spectrometry

An isotope dilution method for the determination of chloride ion in aqueous samples is described. The method makes use of the isotopic shift in the rotational lines of the 1–0 band of HCl emitted in the near infrared region of the spectrum by vibrationally excited HCl molecules present in a hydrogen/entrained air flame. Chloride ion in the sample is converted to chlorine gas by electrolysis and swept into a hydrogen/entrained air flame where it is converted into HCl. Because isotope dilution is an absolute method of analysis, matrix effects are minimized, and the chlorine generation step need not be quantitative. With the system described in this paper, samples must contain at least 9 mg of chloride ion per ml, and a 2-ml sample is required. Over the range from 10 to 30 mg Cl⁻ ml⁻¹, the average error was −0.96%, and the average relative standard deviation was 3.3% for seven samples using seven of the more intense lines in the P branch. Compared with standard silver nitrate titrations, the isotope dilution procedure was not affected by such common interferences as bromide ion and iodide ion. The technique was applied to several seawater samples from different regions.     

Spectrophotometric flow injection determination of chloride in ethanol

A flow injection procedure is described for the spectrophotometric determination of chloride in ethanol, based on the mercury(II) thiocyanate—iron(III) reaction. Effects of reagent composition and ethanol content of the sample are investigated in detail. The proposed system can analyse 120 samples of ethanol (94–100% v/v) per hour, with a relative standard deviation lower than 1%, when the chloride content ranges from 0.1–6.0 ppm. Recoveries of ca. 96% are found.     

Methods for separation of trace amounts of platinum and investigation of the influence of interfering elements during platinum determination in copper ores and copper concentrates by graphite furnace atomic absorption spectrometry

A THGA graphite furnace with Zeeman background correction has been used to determine platinum content in copper ore and copper concentrate at the part per billion (ppb) concentration level. Two different procedures for the separation of trace platinum have been applied: (i) use of an ion exchange resin; and (ii) a two-stage method based on platinum separation on inorganic carriers. The influence of interfering elements in the matrix (Cu, Pb, Fe, Ti, V, Au, Pd, Ir, Rh and Al) has been examined using a graphite furnace. It was found that the presence of Cu (12.5–100 mg l⁻¹), Pb (100–500 mg l⁻¹), Fe (100–2000 mg l⁻¹), Ti (25–100 mg l⁻¹), V (25–100 mg l⁻¹), Au (25–300 mg l⁻¹), Pd (20–250 mg l⁻¹), Ir (0.5–3.5 mg l⁻¹) and Rh (0.025–1 mg l⁻¹) in the samples analyzed has no effect on the platinum absorption signal when using a recommended temperature program (T_pyr=1300°C, T_at=2450°C). Spectral interference was observed, which was due to aluminum, as a result of the close neighborhood of the Pt 265.945-nm and Al 266.039-nm lines. This interference could not be eliminated by the Zeeman background correction.     

Neutral desorption extractive electrospray ionization mass spectrometry for fast screening sunscreen agents in cream cosmetic products

High throughput analysis of sunscreen agents present in cream cosmetic has been demonstrated, typically 2 samples per minute, using neutral desorption extractive electrospray ionization mass spectrometry (ND-EESI-MS) without sample pretreatment. For the targeted compounds such as 4-Aminobenzoic acid and oxybenzone, ND-EESI-MS method provided linear signal responses in the range of 1-100 ppb. Limits of detection (LOD) of the method were estimated at sub-ppb levels for the analytes tested. Reasonable relative standard deviation (RSD = 8.4-16.0%) was obtained as a result of 10 independent measurements for commercial cosmetics samples spiked with each individual sunscreen agents at 1-10 ppb. Acceptable recoveries were achieved in the range of 87-116% for direct analysis of commercial cream cosmetic samples. The experimental data demonstrate that ND-EESI-MS is a useful tool for high throughput screening of sunscreen agents in highly viscous cream cosmetic products, with the capability to obtain quantitative information of the analytes.     

Studies on vanadium(IV) complexes of azoxine s dyes

Comparative studies of the reaction of 7-arylazo-8-hydroxyquinoline-5-sulphonic acid (Azoxine S) dyes with vanadium(IV), show that 2:1 yellow, water-soluble complexes are formed over the pH range 2.5–6, and that the phenyl derivative is the most suitable for spectrophotometric determination of 0.2–1.4 ppm of vanadium(IV). The colour is formed instantaneously and is stable for about 8 hr. The molar absorptivity at λ_max, 400 mμ;, is 1.15 × 10⁴, and the equilibrium constant for complex formation is of the order of 10². These dyes can also be used as indicators in the direct complexometric determination of vanadium(IV). The interference of a number of anions and cations is reported.     

固相萃取-GC/MS法测定水样中20种有机氯农药

建立了用固相萃取小柱提取和净化、GC/MS定性定量同时测定水样中20种有机氯农药的方法。方法采用OasisHLB固相萃取小柱萃取富集水样,二氯甲烷洗脱,加入菲-d₁₀作为内标,利用GC/MS进行定性定量,步骤简便,线性响应良好,干扰小,方法检出限为0.21～0.72 ng/L（按水样1L计）,加标回收率为64.8%～122%,RSD为1.2%～11.0 %。成功利用该方法对广西实际河水样品进行了检测。结果表明方法可以同时满足环境水样中20种痕量有机氯农药的测定。     

A sequential injection method for the determination of piroxicam in pharmaceutical formulations using europium sensitized fluorescence

A simple, selective and sensitive luminescence method for the assay of piroxicam (PX) in pharmaceutical formulation is developed. The method is based on the luminescence sensitization of europium (Eu³⁺) by complexation with PX. The signal for PX–EU is monitored at λ_ex=358 nm and λ_em=615 nm. Optimum conditions for the formation of the complex in methanol were 0.01 M TRIS buffer and 0.2 mM of Eu³⁺ which allows the determination of 100–2000 ppb of pX in batch method and 100–1000 ppb with limit of detection (LOD) = 23.0 ppb using sequential injection analysis (SIA). The relative standard deviations of the method range between 2 and 3% indicating excellent reproducibility of the method. The proposed method was successfully applied for he assay of PX in pharmaceutical formulations (Feldene capsules and tablets). Average recoveries of 101.0±0.3 and 98.8±2.7% were obtained for capsules in methanol using batch and sequential injection (SI) methods, respectively.     

Spectrophotometric method for the determination of vanadium in uranium rich hydrogeochemical samples using pyridyl azo resorcinol (PAR)

A simple and precise method has been developed for the determination of traces of vanadium(V), using 4-(2 pyridyl azo) resorcinol, in natural water samples, containing very high concentrations of uranium. CDTA-pyrophosphate buffer has been used for masking interferants, including uranium which otherwise interferes above 125 ppb. The reaction of vanadium with PAR in the presence of buffer requires a waiting period of 45 min. The Sandell sensitivity of the method is 0.003 microg/ml, at 545 nm at an optimum pH of 6.5 +/- 0.2. The precision of the method is +/- 15% at the 100 ppb level of vanadium(V). The method has been successfully applied to a number of natural water samples during hydrogeochemical exploration.     

On-line determination of cyanide in the presence of sulfide by flow injection with pervaporation

A pervaporation-flow injection (PFI) method is described for the analysis of cyanide in the presence of sulfide. The interfering sulfide ion in the injected sample is precipitated on-line using an acidified lead nitrate reagent solution before the donor stream enters the pervaporation cell. Using amperometric detection at a silver electrode set at −50 mV (vs Ag/AgCl), linear calibration was obtained in the range 0.02–100.0 mg l⁻¹ with a detection limit of 1.0 μg l⁻¹. Sample throughput was of the order of 12–15 h⁻¹. When the method was applied to the analysis of synthetic samples, there was no significant interference from sulfide at concentrations up to 50 mg l⁻¹. Thiocyanate did not interfere at levels up to 1000 mg l⁻¹. When applied to industrial samples containing sulfide and thiocyanate ions where the cyanide ions are predominantly complexed with various metal ions the PFI method was found to give results close to those obtained by standard distillation methods for weak acid dissociable (WAD) cyanide.