PBT／PET共混体系的熔融行为

用差示扫描量热法（ＤＳＣ）考察了ＰＢＴ／ＰＥＴ共混体系的结晶熔融行为，在共混体系中两组份的结晶熔上均随着含量的减小而下降，熔点下降既有形结构变化因素，又有因两组份相容而引起的热力学因素。熔融热焓△Ｈｍ的变化与两组份结晶熔点的变化有相似的规律。这些结果说明在共混体系中ＰＥＴ、ＰＢＴ两组份在结晶一熔融过程中存在相互协同作用，同时也说明ＰＢＴ、ＰＥＴ两组份是晶相分离的，而非晶区是相混容的。     

PBT／PET共混体系的协同效应

ＰＢＴ、ＰＥＴ具有良好相容性，且两种聚合物分子链间存在相互作用，它们的共混体系在熔体降温结晶过程中以及溶液中均表现出协同效应。虽然ＰＢＴ、ＰＥＴ在共混体系中各自形成晶区，但熔体降温结果过程中只能观察到一个结晶放热峰，当ＰＢＴ／ＰＥＴ共混物中两组份分子链段数目相近时，熔体降温结晶峰温较低，峰形变宽，共混体系的结晶程度降低在溶液中两组份分子链段数目相近时，共混物特性粘度（η）值最大，分子链的均方根末端     

极低密度聚乙烯与其它聚乙烯的共混

从结构角度，用ＤＳＣ，ＷＡＸＤ，ＳＡＸＳ研究了聚乙烯（ＰＥ）家族中极低密度聚乙烯（ＶＬＤＰＥ）与其它ＰＥ的互容性．ＨＤＰＥ／ＶＬＤＰＥ是共晶互容的，以其大量无规部分“溶解”了ＨＤＰＥ的结晶缺陷部分，提高了ＨＤＰＥ的Ｔｃ，Ｔｍ，Ｘｃ，结晶峰半高宽变窄，晶胞参数随组成而有最低值．ＶＬＤＰＥ与ＬＬＤＰＥ结构极为相似，ＤＳＣ及ＷＡＸＤ证明其共混物是共晶相容体系．ＬＤＰＥ／ＶＬＤＰＥ的结晶度符合按组成的计算值，但晶胞参数ａ，ｂ以及晶粒尺寸增大，ＤＳＣ上有分别相应于两组份的两个Ｔｍ；ＶＬＤＰＥ的Ｔｃ，Ｔｍ峰高之和高于按组份的计算值，ＬＤＰＥ的Ｔｍ，Ｔｃ则低于计算值．认为是正如ＬＬＤＰＥ／ＬＤＰＥ，ＬＤＰＥ向充满整个体积的ＶＬＤＰＥ中不断填入，以ＶＬＤＰＥ为晶核而结晶，形成相分离的不相容体系．     

聚对苯二甲酸乙二酯／热致液晶聚合物共混体系中液晶组分的诱导结晶效应

用差示扫描量热法对聚对苯二甲酸乙二酯（ＰＥＴ）／热致液晶高分子（ＬＣＰ）共混体系的等温和非等温结晶行为进行了研究．结果表明，由于液晶组分的加入，共混体系中ＰＥＴ的结晶速率和结晶度均得到提高．说明ＬＣＰ具有ＰＥＴ结晶成核剂的作用．在较低的ＬＣＰ组分含量下（～２ｗｔ％），这一效果最为明显，说明ＬＣＰ是以很小的微区或某些ＬＣＰ分子链介晶微束的形式对ＰＥＴ的结晶起成核剂的作用．     

混合液晶与尼龙1010三元共混物的研究

采用ＤＣＳ、ＰＯＭ、ＳＥＭ及力学性能测试，研究了不同对羟基苯甲醛和对苯二甲酸乙二醇酯含量的液晶共聚酯ＰＥＴ４０／ＰＨＢ６０（ＬＣＰ１）和ＰＥＴ３０／ＰＨＢ７０（ＬＣＰ２）的共混物与尼龙１０１０为基体的三元混体系。结果表明，液晶共混物的力学性能比单组分有明显提高，通过改变混合液晶中两组分的含量可调节其加工温度与粘度，从而满足了与尼龙１０１０共混的加工窗口要求。混合液晶的加入对尼龙１０１０的结晶与熔融     

磷酸三苯酯对PBT／PET共混体系结晶行为的影响

用广角Ｘ－角线衍射法和差法扫描量热法研究了磷酸三苯酯对ＰＢＴ／ＰＥＴ共混体系结晶行为影响，结果表明：ＴＰＰＷ作为该共混体系的稳定剂，只能延长在熔融状态下酯交换反应发生的时间，ＴＰＰ含量一定时，熔融时间增加，ＰＢＴ，ＰＥＴ之间的酯交换反应同样会发生，不同熔融时间，就要求ＴＰＰ的用量也不相同。ＴＰＰ在ＰＢＴ／ＰＥＴ共混体系中没有结晶成核剂的作用，它也不改变ＰＢＴ，ＰＥＴ的结晶结构。     

PBT／PET共混体系非晶区的相容性

利用ＰＢＴ、ＰＥＴ的特性参数，通过不同组份比ＰＢＴ／ＰＥＴ共混体系的混合自由能△Ｇｍ，从理论上预测其相容性。在一定的条件下△Ｇｍ＜０，ＰＢＴ、ＰＥＴ可以相容。对不同组份比共混体系的玻璃化转变过程从分子链段运动的角度进行分析。     

离聚物Surlyn对PBT/PP共混体系的力学性能及形态结构的影响

用力学性能测试、ＤＭＡ、ＳＥＭ等方法研究了离聚物Ｓｕｒｌｙｎ对ＰＢＴ／ＰＰ共混体系的力学性能及形态结构的影响。结果表明，在ＰＢＴ／ＰＰ共混体系中引入少量Ｓｕｒｌｙｎ可以改善界面的粘接性，从而改善其力学性能。当共混体系中ＰＢＴ／ＰＰ的组份比不变（９０／１０）且Ｓｕｒｌｙｎ的含量为６ｐｈｒ左右时，共混物的冲击强度出现极大值；而弯曲强度在Ｓｕｒｌｙｎ含量为１－２ｐｈｒ左右时有最大值。当共混体系中Ｓｕｒｌｙｎ的含量不变（６ｐｈｒ）时，其力学性能随ＰＰ含量的增加而下降。用玻璃纤维增强共混体系，可显著提高力学性能。     

高密度聚乙烯与乙烯丙烯辛烯—1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性。     

高密度聚乙烯与乙烯丙烯辛烯－1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性．     

Miscibility of Semi-flexible Thermotropic Liquid Crystalline Copolyesteramide with Polyamide 66

IntroductionIn sl'tu polymer composites containing liquid crystalline polymers(LCPs) have attractedconsiderable attention in the past'decades['--'j. But the development of in sl'tu composites is restricted by two factors. First, the melting temperatures of thermotropic liquid crystallinepolymers (TLCPs) are generally higher than those of the commodity engineering resins. Athigh processing temperatures, these resins tend to become unstable, thereby, causing seriousproblems during fiber spinn…     

聚酯／聚醚酯高分子混合系的凝集状态和结晶化机理

研究了结晶性高分子聚对苯二甲酸乙二酯（ＰＥＴ）聚二苯氧乙烷（１,２）二甲酸（Ｐ．Ｐ′）乙二酯（ＰＥＥＴ）混合系的热结晶化机理．用ＤＳＣ,Ｘ光,偏光显微镜观测研究发现,ＰＥＴ与ＰＥＥＴ的熔融混合并未发生酯交换和共聚合等化学反应,各组分独立结晶,它们的结晶度、结晶速度、球晶结构受到结晶化温度和混合组成两因子的影响,提出了表征这种效果的综合结晶化阻碍因子值．     

PTT/PET共混体系晶体形态与结晶性能的研究

用差示扫描量热仪(DSC)、广角X射线衍射(WAXD)和正交偏光显微镜研究了聚对苯二甲酸丙二酯(PTT)和聚对苯二甲酸乙二酯(PET)共混体系的晶体形态与结晶性能.结果表明,共混体系结晶性能与PTT的含量有关.PET的加入,使共混体系的球晶尺寸减小.球晶完善性降低.当PTT含量为40wt%～60wt%时,共混物分别出现了双重熔融峰和双重结晶峰.双重熔融峰是加热过程中熔融重结晶造成的,双重结晶峰说明不完善的晶体产生的次级结晶.     

多组分单体接枝聚丙烯/尼龙6反应共混物结晶行为研究

用多组分熔融接枝的方法将甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)共同接枝到聚丙烯 (PP)上 ,制得具有较高GMA接枝率的多单体接枝聚丙烯 ,PP g (GMA co St) .将PP g (GMA co St)与尼龙 6 (PA6 )进行共混 ,利用扫描电镜 (SEM) ,差示扫描量热计 (DSC)和广角X射线衍射 (WAXD)对共混物的形态和结晶进行了研究 .在共混过程中 ,PP g (GMA co St)与PA6反应原位生成了PP g PA6 ,有效改善了共混物的相容性 ,分散相尺寸明显减小 .在PP g (GMA co St) PA6为 3 7的体系中 ,PP g (GMA co St)出现分级结晶现象 ,其在较低温度下的结晶属于均相成核结晶 .在PP g (GMA co St) PA6为 7 3的体系中 ,由于PA6相分散细微 ,在通常结晶温度下不结晶 ,而是在低温下均相成核与PP g (GMA co St)同时结晶 .WAXD证实体系中接枝PP ,PA6为分别结晶 ,无共晶或新的晶型产生     

三元共聚液晶聚酯酰亚胺/PET共混体系结构与性能研究

通过熔融共混的方式,将实验室自行设计合成的三元共聚热致液晶聚酯酰亚胺(PPDI)与聚对苯二甲酸乙二酯(PET)进行共混,制备一系列不同液晶聚合物含量的共混体系.采用示差扫描量热仪(DSC)、广角X-射线衍射仪(WAXD)和动态力学性能分析仪(DMA)对共混体系的结构与性能进行表征.结果表明,共混体系中两组份之间具有良好...     

Non-isothermal crystallization behavior of Styrene butadiene rubber/high density polyethylene binary blends

The thermal and crystallization behavior of the blends are studied by differential scanning calorimetry and XRD. The presence of the amorphous component in the blend is found to influence the non-isothermal crystallization of HDPE. The addition of small quantities of SBR resulted in an increase in the rate of crystallization whereas nucleation is delayed. As compared to HDPE, larger crystallite size, a narrower size distribution, were observed in low SBR (~up to 30?wt%) content blends. The half time of crystallization also found to reduce as the SBR content in the blend increased. However, a lower degree of crystallinity was observed in these blends. The results thus show that incorporation of SBR in HDPE, while accelerating the rate of crystallization, lower the degree of crystallization. The reduction in the overall crystallization rate at high-SBR content is attributed to a decrease in the growth rate in the later stages of crystallization. It is observed that in dynamically cross-linked blends, the presence of crosslinked SBR that can acts as heterogeneous nuclei facilitated the nucleation of HDPE. However, the crystal growth may be impeded. As a result the overall crystallinity of the crosslinked blends found to decrease. From XRD profiles it had seen that addition of SBR and dynamic crosslinking does not exert an effect on the crystalline structure of HDPE. The dynamic vulcanization of SBR/HDPE blends enhanced the process of crystallization of HDPE phase. These conclusions are supported by the thermal characterization (DSC) results also.     

Microhardness and thermal stability of compatibilized LDPE/PA6 blends

Microhardness tests, water absorption and thermogravimetric measurements have been performed on blends of low density polyethylene (LDPE) with different molar mass and polyamide 6 (PA6) compatibilized with 2 pph poly(ethylene-co-acrylic acid) (Escor 5001 by Exxon). The negative deviation of Vickers microhardness from the additivity has been interpreted by changes in the crystallinity of the blend components. The hardness values of the compatibilized blends that are lower than those of the corresponding uncompatibilized blends have been explained by the decrease of the degree of crystallinity of PA6 phase in the presence of Escor. The molar mass of LDPE almost does not influence on the hardness values. The lower water absorption of the compatibilized blends, caused by the formation of a copolymer between PA6 and the compatibilizer leads to microhardness values of the wet compatibilized blends higher than those of the corresponding uncompatibilized blends. The thermogravimetric measurements demonstrate that the thermal stability of blends increases in the presence of 2 pph Escor 5001. The results confirm the compatibilizing efficiency of Escor 5001 towards LDPE/PA6 blends in a wide composition range.     

Effects of the oriented mesophase on the cold crystallization of syndiotactic polystyrene and its blend with poly(2,6‐dimethyl‐1,4‐phenylene oxide)

The effects of molecular orientation on the crystallization and polymorphic behaviors of syndiotactic polystyrene (sPS) and sPS/poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) blends were studied with wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry. The oriented amorphous films of sPS and sPS/PPO blends were crystallized under constraint at crystallization temperatures ranging from 140 to 240°C. The degree of crystallinity was lower in the cold‐crystallized oriented film than in the cold‐crystallized isotropic film. This was in contrast to the case of the cold crystallization of other polymers such as poly(ethylene terephthalate) and isotactic polystyrene, in which the molecular orientation induced crystallization and accelerated crystal growth. It was thought that the oriented mesophase was obtained in drawn films of sPS and that the crystallization of sPS was suppressed in that phase. The WAXD measurements showed that the crystal phase was more ordered in an sPS/PPO blend than in pure sPS under the same annealing conditions. The crystalline order recovered in the cold‐crystallized sPS/PPO blends in comparison with the cold‐crystallized pure sPS because of the decrease in the mesophase content. The crystal forms depended on the crystallization temperature, blend composition, and molecular orientation. Only the α′‐crystalline form was obtained in cold‐crystallized pure sPS, regardless of molecular orientation, whereas α′, α″, and β′ forms coexisted in the cold‐crystallized sPS/PPO blends prepared at higher crystallization temperatures (200–240°C). The β′‐form content was much lower in the oriented sPS/PPO blend than in the isotropic blend sample at the same temperature and composition. It was concluded that the oriented mesophase suppressed the crystallization of the stable β′ form more than that of the metastable α′ and α″ forms during the cold crystallization of sPS/PPO blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1665–1675, 2003     

Melt-crystallization behavior and isothermal crystallization kinetics of crystalline/crystalline blends of poly(ethylene terephthalate)/poly(trimethylene terephthalate)

The melt-crystallization and isothermal melt-crystallization kinetics of poly(ethylene terephthalate)/poly(trimethylene terephthalate) blends (PET/PTT) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy. Although PET and PTT in the binary blends are miscible at amorphous state, they will crystallize individually when cooled from the melt. In the DSC measurements, PET component with higher supercooling degree will crystallize first, and then the crystallite of PET will be the nucleating agent for PTT, which induce the crystallization of PTT at higher temperature. On the other hand, in both blends of PET80/PTT20 and PET60/PTT40, the PET component will crystallize at higher temperature with faster crystallization rate due to the dilute effect of PTT. So the commingled minor addition of one component to another helps to improve the crystallization of the blends. For blends of PET20/PTT80 and PET40/PTT60, isothermal crystallization kinetics evaluated in terms of the Avrami equation suggest different crystallization mechanisms occurred. The more PET content in blends, the fast crystallization rate is. The Avrami exponent, n = 3, suggests a three-dimensional growth of the crystals in both blends, which is further demonstrated by the spherulites formed in all blends. The crystalline blends show multiple-melting peaks during heating process.     

马来酸酐接枝热塑性弹性体在PP/PA6共混物中的作用

研究了马来酸酐接枝热塑性弹性体 (TPEg )作为增容剂对聚丙烯 (PP) 尼龙 6 (PA6 )共混体系的相容性、相态以及物理力学性能的影响 .研究结果表明TPEg的加入大大改善了PP PA6共混体系的相容性 ,且随TPEg含量的增大分散相粒径明显降低 ,共混物的韧性以及延展性大大提高 ,同时拉伸强度及模量仍保持较好的水平 .TPEg增容的PP PA6共混物的非等温结晶行为的研究表明 ,共混物中PP和PA6的结晶行为不同于各自纯的聚合物 ,PA6作为成核剂使PP的结晶温度提高 ;而PA6由于TPEg的加入 ,出现分级结晶现象 ,一级结晶温度略低于纯PA6的结晶温度 ,且随TPEg含量增大结晶受阻 ,二级结晶温度与PP的接近 .由于PP、PA 6以及TPEg之间存在较强的相互作用 ,三元共混物中PP及PA6的玻璃化转变温度分别较其纯聚合物升高 .基于上述结果 ,提出了本共混体系的结构模型