两Ag-TPB电极上的零电流示波双电位滴定法

将银片(或碳棒、铂片等)依次浸入Na-TPB及AgNO_3溶液中,得到用于示波电位滴定的Ag-TPB电极。在这种电极上进行双电位滴定。并用示波器直接指示⊿E的变化,确定滴定终点。方法简便灵敏,且可用于药物分析。     

铜修饰电极上铜(Ⅱ)的示波电位滴定法

用示波电位滴定法测定铜,已有文献报道[1,2],大多数是用铂电极和自制的碳糊电极作为指示电极。笔者研究了用铜(Ⅱ)为修饰物,对铜电极进行吸附修饰,使铜电极产生一定的电位响应,对铜(Ⅱ)进行示波电位滴定,根据示波器上的荧光点最大位移为终点。结果表明,铜(Ⅱ)在0.50-350.00 mg范围内均能准确测定。该法用于含铜样品中铜的测定,结果与标准值吻合较好。1试验部分1.1主要仪器与试剂SR8型双踪示波器;磁力加热搅拌器;甘汞电极和铜修饰电极。EDTA标准溶液:0.01 mol·L-1,按文献[3]配制;铜(Ⅱ)标准溶液:1.000 0 g·L-1。1.2铜修饰电极的制备将…     

膜电极上并联电容和控制电流示波电位滴定法

本文研制了几种含聚氯乙烯（ＰＶＣ）膜的选择性电极，使用两种克服电极上交流噪音的方法即并联电容和控制电流示波电位滴定法测定Ｃｕ＾２＋、Ｎｉ＾２＋等金属离子以及ＴＰＢ＾－、Ｍｎｏ４等阴离子并对盐酸左旋咪唑，盐酸阿米替林，心得安等药物含量进行了测定，文中还对这两种方法消除交流噪音的机理进行了探讨，获得满意的结果。     

修饰铂电极上Mn(Ⅱ)的示波双电位滴定法测定

制备了Mn(Ⅱ)修饰铂电极,用循环伏安法表征了修饰电极的电化学性能,并对电极响应机理进行了探讨.优化了试验条件,提出了一种新的测定Mn(Ⅱ)的示波双电位滴定法.在1.0 mol/L的六次甲基四胺底液(pH=5.5～6.6)中,用修饰电极作为双指示电极,以EDTA标准溶液滴定Mn(Ⅱ),利用示波器屏幕上荧光点的显著最大位...     

PVC膜电极上的示波电位滴定法及其在药物分析中的应用

本文研究了用于示波电位滴定的PVC膜电极,成功地用于中和、络合及沉淀滴定,并探讨了它们在药物分析中的应用。所研究电极见表1。实验部分一仪器与试剂 SR-071型双踪示波器,213型铂片电极     

示波电位滴定法测定COD的研究

本文用回流处理样品，以示波电位滴定法测定水中化学耗氧量（ＣＯＤ），方法简单，终点变化敏锐，特别适宜于有色和有悬浊物的样品分析。     

双修饰电极零电流示波双电位滴定的研究——混合酸的连续滴定

本文采用双聚苯胺修饰电极进行示波双电位滴定,用示波器直接指示△E的变化,以示波器荧光屏上荧光点最大位移指示终点。方法简便、快速、直观,用于乙二醛母液中混合酸的连续滴定,结果满意。     

EDTA滴定钴(Ⅱ)的示波电位滴定法——用EDTA修饰的铂电极作为指示电极

制备了用EDTA修饰的铂电极并用循环伏安法检测了修饰电极的电化学性能,在以钴(Ⅱ)标准溶液滴定EDTA溶液的示波电位滴定中,用两支上述修饰电极作为双指示电极体系。当在阴极示波器的屏幕上观察到荧光点的突然最大位移即可判定滴定终点。取10.00 mg钴(Ⅱ)按此方法连续测定15次,所得终点电位值均在45 mV左右,算得其相对标准偏差(RSD)值为0.01。滴定操作在pH 10~11的氨性缓冲溶液中进行,可按需要加入诸如氟化物、酒石酸盐之类的络合剂。测定质量在1.2~31.2 mg之间的钴(Ⅱ)时,回收率在99.9%~100.3%之间。将此方法应用于陶瓷着色剂中Co2O3的测定,所得结果与已知值相符,测定的RSD值(n=7)小于0.05%。     

查尔酮冠醚PVC膜钾离子选择性电极的初步研究

查尔酮冠醚ＰＶＣ膜钾离子选择性电极的初步研究李廷盛，蔡汉临，王传林，张建明，魏旭东，胡宏纹（华中师范大学化学系武汉４３００７０））（南京大学化学系南京）关键词查尔酮冠醚ＰＶＣ膜，钾离子电极，性能钾离子在生物细胞膜内外的浓度梯度对生物膜的能量传输等起着...     

PVC膜离子选择电极检测下限的优化

价格低廉、携带方便、适用浓度宽、操作简单快捷、能耗低的离子选择电极在医院、分析实验室、野外等领域得到了越来越广泛的应用。尽管如此,由于PVC膜中存在的离子流严重破坏了更低检测下限的获取,限制了离子选择电极的进一步发展。因此,本文从减小甚至消除PVC膜中存在的离子流角度出发,系统论述了优化PVC膜离子选择电极检测下限的原理和优良策略,根据收集归纳的大量数据定量阐述传感膜组成的优化、电极组装和调制、应用旋转电极以及电流极化处理等对检测下限的优化提升作用,进一步总结出各种方法的改善规律,分析它们的优势和面临的问题。提出在PVC铸膜液中要突破传统配方,减小增塑剂和离子交换剂用量,以抑制传感膜两侧的离子流,同时外加电流补偿处理等也是降低电极检测下限的有效方法,对检测下限的改善最好的可降低5个数量级。这一总结为PVC膜离子选择电极的高性能化明确了研究方向。     

Cationic Surfactant Ion-Selective PVC Membrane Electrode Containing Macrocyclic Diimine Crown Ether

ABSTRACT

DP⁺ ion-selective PVC membrane electrode based on 2,3,11,12-dibenzo-5,9-diaza-4,9(10)-cis-diimino-1,13-dioxacyclopentadecane as a novel macrocyclic diimine crown ether is proposed. o-Nitrophenyl octyl ether as plasticizer and potassium tetrakis(4-chlorophenyl)borate as lipophilic salt were used. The electrode exhibits a Nernstian response for 1.0 x 10^?2-1.0 x 10^?6 mol 1^?1 DPCl with a slope of 58 mVdecade^?1. The detection limit is 2.5 x 10^?7 mol 1^?1. The electrode response was stable over a wide pH range (3-11). The lifetime of the electrode was about 2 months. The electrode shows a high selectivity towards inorganic cations. Among the organic cations tested, only hexadecyltrimethylammonium ion interferes. The electrode was suitable for determining the critical micelle concentration and as an end-point detector in the potentiometric titration of the cationic surfactants.     

PVC matrix membrane sensor for potentiometric determination of dodecylsulfate

The construction and performance characteristics of a new potentiometric PVC membrane sensor for the determination of sodium dodecyl sulfate (SDS) are described. The sensor was based on the use of an N-cetyl-N,N,N trimethyl ammonium (CTA) dodecyl sulfate (DS) ion pair as ion exchange sites in PVC matrix in the presence of o-nitrophenyl octylether as plasticiser. The sensor exhibited a fast, stable, and near-Nernstian response for SDS over the concentration range of 1 × 10^?3 to 10^?6 M at 25°C and the pH range 4–8.5 with anionic slope of 52.5 ± 0.5 mV decade^?1. The lower detection limit was 3 × 10^?6 M, and the response time was 25 s. Selectivity coefficients of SDS with respect to a number of different species were investigated. There were negligible interferences caused by most of the investigated anions. The determination of 1.0–280.0 µg mL^?1 of SDS in aqueous solutions showed an average recovery of 99.1%, and the mean relative standard deviation was 1.4 at 100 µg mL^?1. The results obtained in the determination of SDS in liquid soap, water and in some pharmaceutical preparations compared favourably with those obtained by the Methylene Blue active substance method (MBAS). In the present investigation, the DS sensor has been used as an end-point indicator electrode for some precipitation titration reactions, e.g. titration of SDS with CTMABr and cetylpyridinium chloride with SDS.     

Asymmetrical Schiff Bases as Carriers in PVC Membrane Electrodes for Cadmium (II) Ions

5‐[((4‐Methyl phenyl) azo)‐N‐(6‐amino‐2‐pyridin) salicylaldimine] (S₁), and 5‐[((4‐methyl phenyl) azo)‐N‐(2‐diamino‐2‐cyano‐1‐ethyl cyanide) salicylaldehyde] (S₂) with N and O donor atoms are effective ionophores to make Cd²⁺‐selective membrane electrodes. The electrodes based on S₁ and S₂ exhibits a Nernstian or near‐Nernstian response for cadmium ion over a wide concentration range 1.5×10^?1–7.5×10^?7 with a slope of 28 and 2.0×10^?1–4.0×10^?7 with a slope of 22, respectively. They have quick response and can be used for three or four months without any divergence in potential. The proposed sensors show fairly good selectivity over some alkali, alkaline earth, transition and heavy metal ions. The electrodes based on S₁ and S₂ can be used in the pH range 3.5–9. These electrodes were used as an indicator electrode in potentiometric titration of cadmium ion with EDTA and in the direct determination of cadmium ion in aqueous solutions.     

PVC膜氯离子选择电极的临床应用研究

本文介绍利用功能高分子活性材料,采用熔融压片成膜的方法研制了PVC膜氯离子选择电极,并对电极性能进行测试并做了临床应用试验,结果表明:电极在10~(-1)M Cl~-中稳定性好,响应时间快,在10~(-1)～10~(-4)M Cl~-中电极呈能斯特响应,其斜率为56～57mV/pCl~-。经临床检测血液标本,该电极抗蛋白、脂类、血球能力强,可以满足临床检测的要求。     

新型PVC膜涂丝诺氟沙星选择电极的研制与应用

制备了一种稳定性和重现性均良好的新型PVC膜涂丝诺氟沙星选择电极 ,该电极是以Ag/AgCl丝为基体 ,在其表面先涂一层含Cl-的脲醛树脂 ,然后再涂一层含硅钨酸 -诺氟沙星离子缔合物的PVC膜。采用正交设计法 ,研究了离子缔合物的种类、活性物在膜中的含量及增塑剂3因素对电极的影响。电极的线性范围为7.9×10 -5～1.0×10 -2mol·L -1 ,检出限为2.5×10 -5mol·L -1,斜率为35.7mV/decade(30℃) ,可直接用于诺氟沙星胶囊的含量测定 ,回收率为99 %～102 % ,结果与中国药典法基本一致。     

脂溶性金属酞菁的合成及其作为PVC膜电极载体的研究

脂溶性金属酞菁的合成及其作为ＰＶＣ膜电极载体的研究李俊忠,庞新宇,陆素,高德,俞汝勤（湖南大学化学化工系,长沙,４１００８２）关键词脂溶性金属酞菁,载体,ＰＶＣ膜电极金属酞菁由于价廉、稳定及其所具有的氧化还原性、光导电和催化等独特的物理化学性质,已在...     

Determination of Fluoride Ions in Mouthwash Samples by a PVC Membrane Samarium(III) Sensor

Abstract

In this study, a new ion-selective electrode for Sm³⁺ is described, illustrating 2-[(E)-1-(1H-pyrrol-2-yl)methylidene]-1-hydrazinecarbothioamide (PMH) in a poly(vinylchloride) (PVC) membrane with nitrobenzene (NB) as a plasticizer and sodium tetraphenyl borate (NaTPB) as an anionic additive. The proposed sensor exhibited a Nernstian response for Sm³⁺ ions over a wide concentration range between 1.0 × 10^?2 and 1 × 10^?6 M, with a detection limit of 5.2 × 10^?7 M in the pH range of 4.2–8.5. Moreover, the sensor displayed the Nernstian slope of 19.8 ± 0.3 mV per decade, having a fast response time within 10 s over the entire concentration range. This electrode presented very good selectivity and sensitivity toward the Sm³⁺ ions over a wide variety of cations, including alkali, alkaline earth, transition-metal, and heavy-metal ions. It was used as an indicator electrode in the potentiometric titration of Sm³⁺ ions with EDTA. The membrane sensor was also applied to the determination of fluoride ions in mouthwash samples.     

Amperometry of Heparin Polyion Using a Rotating Disk Electrode Coated with a Plasticized PVC Membrane

Electrochemical method of detection of heparin polyion was developed based on voltammetry of heparin on a rotating glassy carbon (GC) electrode coated with a plasticized PVC membrane. The membrane was deposited on the GC disk by spin‐coating technique using a mixture of solutions of PVC in tetrahydrofuran, and 1,1′‐dimethylferrocene (DMFc) and hexadecyltrimethylammonium tetrakis(4‐chlorophenyl)borate (HTMATPBCl) in o‐nitrophenyl octyl ether. UV/vis reflection spectrometry was used to evaluate the membrane thickness, which exhibits a linear correlation with the membrane resistance measured by impedance spectroscopy. It is shown that this electrode can be used for amperometric or coulometric detection of heparin in aqueous samples of medically relevant concentrations (1–10 U mL^?1), with a detection limit of 1.4 U mL^?1. Evidence is provided indicating that the current determining step is the reversible adsorption of the ion‐pair of heparin polyion with HTMA⁺ cation at the membrane/aqueous electrolyte interface, which is driven by oxidation of DMFc at the GC/membrane interface.