活性炭富集示波极谱法测定水中痕量钒

本文研究了钒在活性炭上的吸附行为和解吸附条件，建立了ｐＨ３－４条件下吸附，氢氧化钠溶液洗脱，示波极谱法测定水中痕量钒的方法，本法富集倍数为１００，对水样的最小检出浓度为０．０５μｇ／Ｌ加标回收率为８７．４％－１００．３％，７份平行样品测定的相对标准偏差为３。５％－１２．８％。     

活性炭富集二苯偶氮羰酰肼分光光度法测定水中痕量钒

采用粒径≤９０μｍ 活性炭吸附富集天然水中痕量钒,并用二苯偶氮羰酰肼分光光度法测定。研究了钒在活性炭上的吸附行为和解吸条件。采用在ｐＨ３～４．５ 的条件下吸附,１ ｍ ｏｌ／ＬＮａＯＨ 溶液洗脱,本法富集倍数达１００ 倍,样品中钒的检出下限为３．９×１０－ ９ｇ／Ｌ ,标准加入回收率为８８％ ～１０３％ ,相对标准偏差小于１０％ 。方法已用于自来水,漓江水等环境水样中痕量钒测定。     

催化动力学光度法测定痕量钒(Ⅴ)的研究

研究了在ｐＨ９．２的硼砂介质中，痕量钒（Ⅴ）催化Ｈ２Ｏ２氧化桑色素褪色反应体系的新催化光度法。测量范围为０～７．５μｇ／５０ｍＬ加标回收率为９５％～９８．５％，测定２μｇ钒（Ⅴ），ＲＳＤ为１．６８％，用于水样中痕量钒（Ⅴ）的测定。     

贵金属同时浮选分离富集行为的研究及ICP－AES的测定

本文通过对贵金属－碘化钾－孔雀绿显色体系的浮选行为研究，建立了一种同时浮选富集分离铂、钯、铑、铱、金的新方法。实验结果表明，在０．３６ｍｏｌ／ＬＨＣｌ０．１ｍｏｌ／ＬＫＩ和２．４×１０￣（－４）ｍｏｌ／ＬＭＧ的溶液中，加入环已烷振荡１ｍｉｎ，铂、钯、铑、铱、金可被定量浮选，继而用ＩＣＰ－ＡＥＳ测定。对含量为５～１５０μｇ的贵金属，浮选回收率分别为铂８８．６％～９５．７％，钯９２．３％～９９．５％，铑９３．７％～１０１％，铱９２％～９８．５％，金８６．４％～９４％。方法应用于铜镍矿、铂网废料等物料中上述贵金属元素的测定，结果满意。     

钼钒磷杂多酸铵蓝的合成和性质研究

本实验采用分步加原料的方法，以不同的磷钼钒比，直接合成了三种１：１２系列的钼钒磷杂多酸铵蓝，即（ＮＨ４）４Ｈ２·１５Ｈ２Ｏ（ｂｌｕｃ—１），（ＮＨ４）５Ｈ２·和（ＮＨ４）６Ｈ２·３０Ｈ２Ｏ（ｂｌｕｃ－３），并研究了反应条件对这些钼钒磷杂多酸铵蓝形成的影响．通过元素分析、电位滴定、电子光谱和Ｘ射线衍射等测试手段研究了配合物的性质，并确定了配合物的组成．     

氟化钙增敏石墨炉原子吸收法测定人发和血清样品中痕量钼的研究

石墨炉原子吸收法测定生物样品中痕量钼时，用氟化钙作基体改进剂，可使钼的原子吸光度提高５．７倍，其特征量原来的４．２× １０＾－１１ｇ／１％吸收降低到５．１×１０＾－１２ｇ／１％吸收，测定下限为０．５５ｎｇ·ｍＬ＾－１，线性范围为０～１０００ｎｇ· ｍＬ＾－１． 对人发和牛血清标样中痕量钼测定。结果满意。     

催化动力学光度法测定痕量钒（V）的研究

研究了在ｐＨ９．２的硼矽介质中，痕量钒（Ｖ）催化Ｈ２Ｏ２氧化桑色素褪色反应体系的新催化光度法，测定范围为０～７．５μｇ／５０ｍＬ，加标回收率为９５％～９８．５％，测定２μｇ钒（Ｖ）ＲＳＤ为１．６８％，用于水样中痕量钒（Ｖ）的测定。     

光电直读光谱法测定高速工具钢中多元素

利用美国贝尔德公司生产的ＢＡＩＲＤＳＰＥＣＴＲＯＶＡＣ２０００（ＤＶ－５，ＨＲ－４００光源）光电直读光谱仪测定高速工具钢（Ｗ１８Ｃｒ４Ｖ）中硅，锰，磷，硫，铬，钒，镍，钨和钼，以铁元素做内标，对谱线进行基体和干扰校正，所得分析结果基本与标准值一致，其相对标准偏差为０．２％～５．６％。     

借2—（2—咪唑偶氮）—苯酚—4—磺酸螯合物和液相色谱分离铬,钼,钒和钴

研究了离子对反相高效液相色谱分离铬（Ⅱ）、钼（Ⅵ）、钒（Ⅳ）和钴（Ⅱ）之２－（咪唑偶氮）－苯酚－４－磺酸螯合物的柱前衍生条件；检测波长的选择；流动相中有机溶剂、四丁基溴化铵及酸度的影响，并讨论了１５种外来离子的干扰情况。本方法已用于合金钢和钒喳的分析。检测限为０．４ｎｇ铬、１．２ｎｇ钼和０．１ｎｇ钒。     

硅钼杂多阴离子薄膜修饰电极线性扫描伏安法测定黑液中可溶性硅

本文报导了以玻碳电极为基体的１：１２硅钼杂多阴离子薄膜化学修铈电极的制备及其电化学特性。并应用于导数伏安法测定。在４．０×１０￣（－３）ｍ０ｌ／Ｌ（ＮＨ＿４）＿６ＭＯ＿７Ｏ＿（２４）－６．８×１０￣（－２）ｍｏｌ／ＬＮａ＿３Ｃｉｔ－０．４８ｍｏｌ／ＬＮＨＯ＿３体系中，硅浓度在８．３×１０￣（－７）～１．７×１０￣（－３）ｍｏｌ／Ｌ范围内与峰电流呈良好线性关系，检测限为８．０×１０￣（－７）ｍｏｌ／Ｌ。对可溶性硅（以ＳｉＯ＿２计）为２４５．０５ｍｇ／Ｌ的黑液，稀释１０倍后，取２．００ｍＬ平行测定９次，ＲＳＤ为０．５８％，加标回收率在９７．３％～１０４．４％间。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.