聚乳酸与聚乳酸-羟基乙酸多孔细胞支架的制备及孔隙的表征

应用溶液烧铸致孔剂浸出技术制备了不同致孔剂用量与不同致孔剂颗粒尺寸条件下的一系列聚乳酸及不同组成的聚乳酸－羟基乙酸多孔细胞支架;用一种改进的方法－重量法测定其孔隙率;在聚乳酸－羟基乙酸多孔支架上进行了软骨细胞培养。研究结果表明,随着制备过程中致孔剂用量的增加,多孔支架的孔隙逐渐增加,而与致孔剂的颗粒大小基本无关;致孔剂的颗粒大小只影响多孔支架的孔径;在致孔剂用量及致孔剂颗粒尺寸都相同的情况下,随着共聚物中乙交酯含量的增加,孔隙率逐渐下降;软骨细胞在支架上繁殖情况良好,三周后已开始分泌细胞外基质。     

原代大鼠肝细胞在多孔壳聚糖及其复合物支架上的培养

研究了原代肝细胞在壳聚糖及其复合物多孔支架上的生长及代谢.结果表明,细胞在多孔壳聚糖支架上生长良好,且密度、代谢活性较单层培养条件下有大幅度提高,细胞在7d后仍能保持较强的分泌白蛋白和合成尿素的功能,壳聚糖复合物上肝细胞的代谢活性更高.还从材料的化学结构和几何形态角度对这种材料的优势进行了讨论.     

低热-高压法制备PLGA多孔支架及其体外降解研究

采用低热-高压法制备了聚(dl-丙交酯／乙交酯)75／25(PLGA75／25)组织工程多孔支架。该方法避免了使用有机溶剂，支架的孔隙率在90％以上，孔径大小分布均匀。多孔支架经过酒精处理后，支架表面产生许多微小的凹陷；用藻酸钙改性处理后，支架形态保持良好。两种处理都使支架的压缩强度有所增大，亲水性增强。虽然孔隙率高的支架降解速率稍慢，但其体外降解规律基本一致：特性粘数争力学强度衰减快，而质量损失较慢，降解6周后，支架的质量损失仅为3％左右；体外降解3周后，支架的形态保持良好，可望在细胞移植争组织修复的早期发挥支撑作用。     

胶原-磺化羧甲基壳聚糖/硅橡胶皮肤再生材料的制备及其对小型猪烫伤创面全层皮肤缺损的修复研究

制备了一种胶原-磺化羧甲基壳聚糖/硅橡胶皮肤再生材料,并以小型猪为模型,考察了其对烫伤全层皮肤缺损的修复性能.首先合成了磺化羧甲基壳聚糖,并对其结构进行了表征.制备了胶原-磺化羧甲基壳聚糖多孔支架,采用扫描电子显微镜(SEM)研究了磺化羧甲基壳聚糖含量对支架微结构的影响.随着磺化羧甲基壳聚糖含量的增大,胶原-磺化羧甲基壳聚糖支架从纤维结构向片状结构转化,且支架的孔径相对变大.采用体外成纤维细胞培养实验证明胶原-磺化羧甲基壳聚糖支架无明显细胞毒性.进一步将胶原-磺化羧甲基壳聚糖支架与硅橡胶膜复合,构建具有双层结构的皮肤再生材料.以小型猪为模型,评价了其对深度烫伤创面的修复性能.大体观察和组织学分析结果显示,胶原-磺化羧甲基壳聚糖/硅橡胶皮肤再生材料具有更快的血管化性能,且经该材料处理的创面能有效支持薄自体皮片的移植成活,实现深度烫伤创面的全层修复.     

高压静电法制备多孔磁性壳聚糖微球

以壳聚糖(Chitosan, CS)为基质, 通过共混法引入四氧化三铁磁性颗粒, 以硅胶(Silicagel, S)为致孔剂, 在热的NaOH溶液中溶出硅胶致孔, 采用高压静电法制备磁性壳聚糖微球. 通过SEM观察了微球的结构和形貌, 并对微球结构和形貌的影响因素及其制备工艺进行了系统的研究, 结果表明, 高压静电法制备的磁性硅胶/壳聚糖微球粒径可通过微量进样器的针头大小来控制, 并且粒径分布均匀, 实验重复性及可控性好; 当以质量体积分数为5%的壳聚糖醋酸溶液(体积分数2％, mS∶mCS=4∶1), 用8号针头进样时, 制得直径约为600 μm, 孔洞分布均匀, 孔径约为50 μm的多孔磁性壳聚糖微球. 由于磁性多孔壳聚糖微球中含有大量的活性羟基和氨基, 因此显弱碱性, 对酸性物质和金属离子的吸附作用很好, 且可通过外加磁场进行有效分离. 磁性多孔壳聚糖微球在生物分离及污水中的酸性染料处理方面具有潜在的应用价值.     

医用多孔壳聚糖膜的制备及性能研究

以邻苯二甲酸二丁酯为致孔剂,制备了多孔壳聚糖膜,并用扫描电镜对其表面和断面形貌进行了分析,同时对膜的吸水性、水蒸气透过性、比表面积、力学性能及生物相容性等进行了考察。分析结果表明:以邻苯二甲酸二丁酯为致孔剂,制备的多孔壳聚糖膜孔径均匀,吸水性好,孔隙率高,比表面积大,膜的最大吸水率、孔隙率和比表面积分别为196%、71.5%和1.0472 m2.g-1;膜的力学性能好,最大抗拉强度为273.17MN/m2。     

接枝共聚法制备二氧化钛/聚（苯乙烯-二乙烯基苯）复合微球

本文以KH560、苯乙烯、马来酸酐为连接组分,将二氧化钛接枝到聚（苯乙烯-二乙烯基苯）微球的表面,成功制备了无孔和多孔纳米复合微球。研究了硅烷偶联剂（KH560）和苯乙烯对二氧化钛在无孔微球表面的分散性和接枝数量以及支撑微球的多孔性质对接枝到微球内部的二氧化钛数量的影响。结果表明,KH560和苯乙烯能够提高二氧化钛在微球表面的分散性和稳定性,使二氧化钛以30-80nm的粒径接枝在微球表面。苯乙烯又能使二氧化钛在无孔微球表面的接枝数量从10.4%增大到20.4%。平均孔径为136nm的多孔微球为支撑微球得到的复合粒子中二氧化钛最高接枝量可达26%,明显高于无孔微球和平均孔径为31nm的多孔微球。     

海藻酸壳聚糖可塑性支架材料的制备及表征

利用海藻酸钠和壳聚糖2种原料, 采用阴阳离子静电复合原理, 通过滴注法层层自组装成可搭载药物的缓释微球, 再按一定比例与海藻酸钠-壳聚糖溶液混合制成缓释微球型支架材料, 将缓释微球结构嵌入疏松多孔海绵状结构中. 研究了缓释微球的组分比对缓释微球型支架材料的孔隙率、 收缩率、 亲水性及降解性能的影响; 扫描电子显微镜照片显示, 微球结构相对完整, 多孔海绵状结构孔径为140~200 μm; 支架浸出液细胞毒性检测实验组对照组未见差异. 缓释微球体积所占比例即组分比为10%的缓释微球型支架材料孔隙率最高为68.2%~70.8%, 亲水性最好, 收缩率最低为4.4%~5.2%; 支架降解速率随缓释微球组分比升高而减慢, 组分比为20%的缓释微球型支架材料综合性能更优; 缓释微球型支架材料冻干成型前为液态, 具有良好可塑性. 缓释微球型支架材料为缓释系统与多孔支架材料有机结合提供了新思路.     

以陶瓷纤维为基材的硅胶吸附材料的制备与性能

以陶瓷纤维纸为基材，经水玻璃浸泡，絮凝剂沉积，盐酸调节pH值得到陶瓷纤维基硅胶吸附材料：探讨水玻璃浓度、絮凝剂浓度，盐酸浓度等条件对硅胶吸附剂吸附性能的影响：采用扫描电镜(SEM)，多孔介质孔隙分析仪揭示吸附材料的表面形貌、比表面积及孔径大小。实验结果显示：当水玻璃浓度为26．67wt%，絮凝剂浓度为15wt％，盐酸浓度为0．5mol／L时，吸附剂具有较好的吸附性能：硅胶能较好分散在纤维表面及其空隙中，BET比表面积为347．4m^2／g，总孔容为0．20295cm^2／g，其中，微孔所占比例为50．54％，平均孔径为，微孔0．4939nm，中孔3．907nm。     

多孔不锈钢载体上X型分子筛的生长成膜

 通过对X型分子筛合成方法的改进,获得了适合分子筛在多孔不锈钢载体上成长的条件．通过在不同孔径的多孔不锈钢载体上负载生长分子筛膜,研究了X型分子筛在多孔不锈钢载体上生长的规律,考察了晶化液配比、合成条件及晶化次数对分子筛负载量的影响,还考察了多孔载体的表面形貌及孔径大小对表面膜均匀连续性的影响等．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.