刷涂热分解法制备Ti/SnO2-Sb2O5阳极及其性能

通过刷涂热分解法制备了锑掺杂的钛基二氧化锡(Ti/SnO2-Sb2O5)涂层电极.在酸性介质中,用扫描电镜(SEM)、X射线衍射仪(XRD)、循环伏安和快速寿命测试等方法研究了Ti/SnO2-Sb2O5电极制备条件、电极结构、性能和寿命.结果表明,TFSnO2-Sb2O5电极涂层具有"干泥"结构,用锡锑摩尔比为9:1的涂液组成、在550℃烧结温度下制备的Ti/SnO2-Sb2O5的电极涂层平整致密,龟裂小,电极孔隙率小,稳定性最好.     

刷涂热分解法制备Ti/SnO2-Sb2O5阳极及其性能

通过刷涂热分解法制备了锑掺杂的钛基二氧化锡(Ti/SnO2-Sb2O5)涂层电极. 在酸性介质中, 用扫描电镜(SEM)、X射线衍射仪(XRD)、循环伏安和快速寿命测试等方法研究了Ti/SnO2-Sb2O5电极制备条件、电极结构、性能和寿命. 结果表明, Ti/SnO2-Sb2O5电极涂层具有“干泥”结构, 用锡锑摩尔比为9:1的涂液组成、在550 ℃烧结温度下制备的Ti/SnO2-Sb2O5的电极涂层平整致密,龟裂小, 电极孔隙率小, 稳定性最好.     

Ni-Co/RuO2复合电极的制备及其电催化析氢性能

采用快速凝固结合去合金化的方法制备纳米多孔Ni-Co合金,利用RuO_2对Ni-Co合金进行表面修饰,通过X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)对多孔材料进行物相分析和形貌表征,并通过线性扫描伏安法、多电位阶跃法、交流阻抗法和恒电流电解法测试多孔电极的电催化析氢性能。结果表明,Ni-Co/RuO_2复合电极材料在50 mA·cm~(-2)电流密度下析氢过电位为180 mV,析氢过程由Volmer-Heyrovsky步骤控制,交换电流密度为4.42 mA·cm~(-2),经10 h恒电流电解后电位仅增加20 mV,表现出良好的析氢稳定性。     

SnO2、Ag/SnO2微球的制备及其光催化性能研究

在SnCl_2-H_2C_2O_4-PVP(聚乙烯吡络烷酮)-H_2O的水热体系中,180℃下反应10 h制备了粒径约为900 nm的四方结构的SnO_2微球。以SnO_2微球为基底,通过光还原法,制备了Ag/SnO_2复合微球。用X射线衍射(XRD),扫描电子显微镜(SEM)对产物进行结构表征,并提出了可能的化学反应。以酸性大红为例,研究了SnO_2微球和Ag/SnO_2复合物的光催化性能,结果表明,SnO_2微球和Ag/SnO_2复合物对酸性大红的降解均有一定的光催化效果,而且,Ag的复合可以有效提高SnO_2微球的光催化活性。     

溶剂热法制备石墨烯/SnO2及其气敏性

采用溶剂热法制备了石墨烯/SnO_2(G/SnO_2)纳米材料,利用扫描电子显微镜(SEM)、X射线衍射(XRD)、拉曼光谱(Raman)等对G/SnO_2进行了表征,研究了石墨烯的量和溶剂热温度对该纳米材料气敏性能的影响。实验结果表明,石墨烯可以调节SnO_2晶体的生长:当石墨烯上清液的量为1 mL、热处理温度为160℃时,制备的G/SnO_2纳米材料在室温下对氨气具有较好的气敏选择性和较高的灵敏度;且当气体体积浓度为1 000μL·L~(-1)时,对NH3的灵敏度为266.4,检出限达到了0.01μL·L~(-1)。     

ZnFe2O4/TiO2纳米管阵列电极的制备及光电催化降解苯酚的研究

采用阳极氧化法和电沉积法制备出具有可见光响应的ZnFe2O4/TiO2纳米管阵列电极.用环境扫描电子显微镜(ESEM)、X-射线衍射(XRD)和透射电子显微镜(TEM)对制备的ZnFe2O4/TiO2纳米管阵列电极的表面形貌和结构进行了表征.结果表明,该方法成功地将ZnFe2O4纳米颗粒均匀分散在TiO2纳米管中,分布在管口处的较少.同时,详细讨论了反应物浓度、沉积时间、循环次数、沉积电压对ZnFe2O4/TiO2纳米管阵列电极性能的影响.通过在可见光下降解苯酚评价了复合电极的光催化活性,实验结果表明:由于ZnFe2O4和TiO2之间的协同效应,复合电极的光响应范围扩展到了可见光区域,光电催化活性提高1.5～2倍.     

Ni2+掺杂Ti/SnO2-Sb2O5电极的制备及性能

采用溶胶凝胶法制备了Ni2+掺杂的Ti/SnO2-Sb2O5电极,并通过XRD、SEM、EDS、苯酚降解、加速寿命实验等技术手段,研究了Ni2+的掺杂对电极的结构、形貌、电催化性能及稳定性的影响。结果表明:Ni2+的掺入细化了SnO2晶粒,增大了电极的比表面积,改善了电极表面的龟裂程度,提高了电极的导电性能;相对于Ti/SnO2-Sb2O5电极Ni2+的掺入将苯酚完全降解的时间缩短为原来的40%,将电极的使用寿命提高为原来的4.8倍。     

阳极电沉积条件对Ti/SnO2-Sb2O5/PbO2+Nano-Co3O4复合电极组成、形貌和结构的影响

本文在涂有中间层SnO2-Sb2O5的Ti基体上,采用阳极复合电沉积法制备了Ti/SnO2-Sb2O5/PbO2+Nano-Co3O4复合电极材料,借助于X射线衍射（XRD）、X射线光电子能谱（XPS）、扫描电镜（SEM）等分析方法研究了制备条件对该复合电极材料的组成、结构和形貌的影响。结果表明,纳米Co3O4的掺杂可提高PbO2电极表面的粗糙度和空隙率;沉积电位、镀液中Co3O4粒子浓度及有机溶剂的添加均对镀层中Co3O4的嵌入量有很大影响。     

SnO_(2)/ITO光电化学电极制备及性能研究EI北大核心CSCD

采用商品化氧化铟锡(ITO)导电玻璃、纳米SnO_(2)水胶体分散液,通过旋涂法制备了高性能SnO_(2)/ITO电极,考察了SnO_(2)旋涂浓度、旋涂量、Triton X-100浓度、煅烧温度对SnO_(2)/ITO电极性能的影响,并优化了缓冲体系、pH、浓度及偏压条件。结果表明,当SnO_(2)水胶体分散液浓度15%、Triton X-100浓度0.01%、煅烧温度450℃时,制备的SnO_(2)/ITO电极具有较高的热稳定性和光电化学性能;草酸-草酸钠缓冲体系有利于光电流的产生,当草酸浓度为30 mmol/L(pH 6.0)、偏压为0.5 V时,可以产生较高的稳态光电流信号,以Ru(bpy)_(2)(dppz)^(2+)为光电化学信号探针,检测限为10 nmol/L。考察了ITO电极的性能差异性,同一批次及不同批次之间的光电流信号一致性相对标准偏差(RSD)在3.9%~5.6%之间。     

RuO2修饰纳米多孔Ni-Mo复合电极及其电催化析氢性能

采用脱合金化结合胶体聚沉的方法制备了纳米多孔Ni/RuO_2、Ni-Mo/RuO_2复合电极材料。通过X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电镜(SEM)、透射电镜(TEM)对电极材料的物相、元素组态、形貌结构、孔径大小和结晶度进行表征,并通过线性扫描伏安、交流阻抗以及循环伏安等方法测试多孔电极的电催化析氢性能。分析结果显示:RuO_2由于聚沉作用包覆在Ni基合金的骨架表面。Mo的加入使Ni-Mo合金非晶化的同时,促使其骨架细化,形成双连续的纳米多孔结构。Mo与RuO_2的加入以及Mo含量的增加均提高了电催化析氢性能。纳米多孔Ni_(2.5)Mo_(2.5)/RuO_2复合电极在50 mA·cm~(-2)的电流密度下析氢过电位为182 mV。     

Formation of nano-crystalline quartz crystals from ZnO/MgO/Al2O3/TiO2/ZrO2/SiO2 glasses

Glasses with the compositions 50.9 SiO₂ · 20.8 Al₂O₃ · (20.8 ? x) MgO· × ZnO · 3.7 TiO₂ · 3.7 ZrO₂ with x = 0, 2.3, 4.6 and 9.3 were annealed at temperatures in the range from 850 to 1100 °C. Depending on temperature, high- or low-quartz solid solutions, magnesium aluminosilicate, mullit and spinel precipitated. These glass–ceramics exhibit excellent mechanical properties and are potential candidates for applications in micromechanics or as hard disc substrate.The larger the ZnO concentration, the lower is the glass transition temperature. Also microhardnesses and Young’s moduli increased with increasing ZnO concentration. The nucleation temperature was of minor importance. To achieve good mechanical properties, the initially formed high-quartz phase must transform to the corresponding low-quartz phase. This occurs if the quartz phase contains only minor MgO or ZnO concentrations, which can be achieved by increasing the annealing times or temperature. Then MgO, ZnO and Al₂O₃ occur as separate spinel or gahnite phase.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Synthesis and characterization of inorganic solid electrolytes of Li2O-SiO2-P2O5 and Li2O-TiO2-SiO2-P2O5 systems

The lithium-ion-conducting inorganic solid electrolytes in the oxide systems Li₂O-SiO₂-P₂O₅ and Li₂O-TiO₂-SiO₂-P₂O₅ were prepared by the solid-state reaction, and the electrolyte pellet made by cold-pressing method had diameter of 13 mm and was about 1 mm thick. Phase identification and surface morphology of the products were carried out by X-ray diffraction and scanning electron microscopy. Ionic conductivity of the pellets was investigated through ac impedance. The results show that the adding of other cations can improve the ionic conductivity of the solid electrolyte, and the sintering temperature and duration can influence the ionic conductivity. The maximum ionic conductivity in the samples is 9.9 × 10⁻⁴ S/cm in the Li₂O-TiO₂-SiO₂-P₂O₅ system. Original Russian Text ? W. Li, M. Wang, Z.H. Li, X.F. Shang, H. Wang, Y.W. Wang, Y.B. Xu, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 11, pp. 1341–1345.     

Removal of NO in NO/N2, NO/N2/O2, NO/CH4/N2, and NO/CH4/O2/N2 systems by flowing microwave discharges

In this paper, continuing previous work, we report on experiments carried out to investigate the removal of NO from simulated flue gas in nonthermal plasmas. The plasma-induced decomposition of small concentrations of NO in N2 used as the carrier gas and O2 and CH4 as minority components has been studied in a surface wave discharge induced with a surfatron launcher. The reaction products and efficiency have been monitored by mass spectrometry as a function of the composition of the mixture. NO is effectively decomposed into N2 and O2 even in the presence of O2, provided always that enough CH4 is also present in the mixture. Other majority products of the plasma reactions under these conditions are NH3, CO, and H2. In the absence of O2, decomposition of NO also occurs, although in that case HCN accompanies the other reaction products as a majority component. The plasma for the different reaction mixtures has been characterized by optical emission spectroscopy. Intermediate excited species of NO*, C*, CN*, NH*, and CH* have been monitored depending on the gas mixture. The type of species detected and their evolution with the gas composition are in agreement with the reaction products detected in each case. The observations by mass spectrometry and optical emission spectroscopy are in agreement with the kinetic reaction models available in literature for simple plasma reactions in simple reaction mixtures.     

The preparation of NbH5(Me2PCH2CH2Me2)2 and NbHL2(Me2PCH2CH2PMe2)2 (L = CO or C2H4)

MMe₅(dmpe) (M = Nb or Ta, dmpe = Me₂PCH₂CH₂PMe₂) reacts with H₂ (500 atm) and dmpe in THF at 60°C to give MH₅(dmpe)_2? NbH₅(dmpe)₂ readily reacts with two mol of CO or ethylene (L) to give NbHL₂(dmpe)₂. The exchange of the hydride ligand with the ethylene protons in NbH(C₂H₄)₂(dmpe)₂ is not rapid on the ¹H NMR time scale (60 MHz) at 95°C.     

Study of plasma-polymerization deposition of C2H2/CO2/H2 onto ethylene-co-propylene rubber membranes

Ethylene-co-propylene rubber (ERP) membranes were modified by use of acetylene/carbon dioxide/hydrogen (C₂H₂/CO₂/H₂) plasma-polymerization deposition. The influence of flow rate of gases, glow discharge power and deposition time on the amount of deposition was investigated. Infrared spectroscopy and scanning electron microscopy were employed to study the structure and surface morphology of the deposited EPR membrane. The water contact angle and the permeation property were examined as well. The results showed that deposition comprises oxygen-containing groups including >C=O and –OH, the hydrophilicity of EPR membrane was therefore improved. It was also found that the permeation coefficient of plasma modified EPR membrane decreased with the increase of the amount of deposition.     

Slow energy transfer between vibrational models of CH2Cl2, CD2Cl2, CH2ClBr and CH2Br2

Inefficient vibrational energy exchange between the lowest vibrational mode and the higher lying vibrational modes of CH₂Cl₂, CD₂Cl₂, CH₂ClBr and CH₂Br₂ was investigated by ultrasonic absorption experiments. Breathing sphere theory is used to interpret the data available for VV and VR, T transfer in methylene halides.     

Direct formation of cyclobutenylphosphonates from 1-alkynylphosphonates and Cp2ZrCl2/2EtMgCl/2CuCl

Zirconacycles 2 prepared from 1-alkynylphosphonates 1, zirconocene dichloride, and 2 equiv of EtMgCl are smoothly converted into cyclobutenylphosphonates 3 when treated with two equiv of CuCl in 65-81% isolated yield. The reaction is specific and general only for zirconacyclopentenyl phosphonates.     

Formation of [Cp2TiSbMe2]2, [Cp2TiSb(SiMe3)2]2 and [Cp2TiCl]2·2Mes4Sb2

Reactions of [Cp₂Ti(btmsa)] (btmsa = bis(trimethylsilyl)acetylene) with R₄Sb₂ (R = Me, Me₃Si) give [Cp₂TiSbMe₂]₂ (1) or [Cp₂TiSb(SiMe₃)₂]₂ (2) respectively. [Cp₂TiCl]₂·2Mes₄Sb₂ (3) is serendipitously formed from [Cp₂Ti(btmsa)] and Mes₂SbH containing NH₄Cl traces.     

TiO2/SiO2/CeO2复合纳米薄膜超亲水性能的研究

采用溶胶凝胶法在载玻片表面制备了均匀透明的TiO2-SiO2-CeO2超亲水性薄膜，并用X射线衍射、傅立叶红外光谱、紫外-可见分光光度计研究了SiO2及稀土铈添加对TiO2薄膜表面特征及超亲水性能的影响。结果表明，Ti02-SiO2-CeO2薄膜亲水性能及亲水持续效应显著提高。实验中掺杂的铈是以三价离子态引入的，由于Ce^3 在高温下很容易氧化，故在薄膜中铈主要以四价态形式存在。Ce^4 在光激发下很容易捕获光生电子生成Ce^3 离子，光生空穴则与表面氧离子反应形成氧空位，而氧空位对亲水性的提高具有关键作用。添加SiO2后，薄膜表面的羟基含量增加，这主要是由于TiO2与SiO2复合在表面形成Lewis酸所致。表面稳定的羟基可使亲水性在暗中保持较长时间，因而亲水持续效应提高。添加SiO2及稀土铈后，薄膜中TiO2晶粒尺寸变小，量子效应增强，这也导致亲水性提高。因此添加稀土铈及SiO2后，薄膜表面的氧空穴增多，薄膜的超亲水性及亲水持续效应提高。