Growth and morphology of ruby crystals with unusual chromium concentration

Single crystals of ruby have been obtained from fluxed melts based on the systems Li₂O–MoO₃, Li₂O–WO₃, Na₂O–WO₃, 2PbO–3V₂O₅, PbO–V₂O₅–WO₃, PbF₂–Bi₂O₃ and Na₃AlF₆ by both the TSSG method and spontaneous crystallization at the temperatures 1330–900 °C. Al₂O₃ solubility has been measured for the flux composition of 2Bi₂O₃–5PbF₂ in the temperature range 1200–1000 °C and dissolution enthalpy has been defined as 29.4 KJ/Mol. The composition of grown crystals was studied by electron microprobe analysis. The synthetic ruby contains from 0.51 to 6.38 at% of chromium admixture depending on the crystal growth conditions. Experimental results on growth conditions, composition and morphology of grown crystals are presented for each flux and temperature interval.     

Porous crystal structures obtained from directionally solidified eutectic precursors

Interconnecting cage-like porous structures of several halide compounds were prepared by the selective leaching of one eutectic phase method. The binary eutectic precursors were prepared by directional solidification using the Bridgman crystal growth technique. Porous NaMgF₃ (40% pore volume), CaF₂ (57% pore volume) and BaF₂ (43% pore volume) crystals were obtained after water leaching the NaF component of the directionally solidified NaF/NaMgF₃, NaF/CaF₂ and NaF/BaF₂ eutectics with the appropriate entangled microstructure. The growth conditions for eutectic-coupled growth and the morphology of the eutectics have been determined. In the coupled growth regime, the size of the eutectic phases “λ” is fairly uniform and varies with the eutectic growth rate “v” as λ²v=constant, which allows us to control the pore size within the 0.5–10 μm range. The simplicity and versatility of the eutectic growth also allows us to fabricate highly aligned porous structures at relatively high production rates.     

Chemical strengthening of Na2O---Al2O3---SiO2 system glasses by surface controlled crystallization

Appropriate glass compositions of the Na₂O---Al₂O₃---SiO₂ system and glass melting technology were investigated. The dependence of some factors, such as composition of molten salts, time and temperature of ion exchange treatment on the modulus of rupture was studied. As expected, the coefficient of interdiffusion is a function of concentration and has the mixed-alkali effect. The order of the interdiffusion coefficient is 10⁻⁶ cm²/s. The effect of binary and ternary salt baths on the surface controlled crystallization was reported. The experimental data showed that there is a series of technological advantages from applying molten salts of the ternary system Li₂SO₄---Na₂SO₄---K₂SO₄ in comparison with the binary system Li₂SO₄---Na₂SO₄.     

Effect of molecular weight of polystyrensulfonic acid sodium salt polymers on the precipitation kinetics of sodium bicarbonate

This paper analyzes the effect of polystyrensulfonic acid sodium salt (NaPSS), obtained by kinetic precipitation from solutions of polymers of molecular weight 245 000 and 38 000 g mol⁻¹ in sodium bicarbonate (NaHCO₃) itself precipitated from synthetic brine. Crystal size, shape and the additive adsorbed are reported. X shaped and hexagonal prisms crystals with different aspect ratios were obtained. The results show that with increasing polymer concentration the crystal size decreases, from 0.27 to 0.48 mm. Additionally, the higher molecular weight polymer shows both higher adsorption capacity and higher crystal habit modification. Crystal shape patterns were similar for both polymers; however, the higher molecular weight material induced changes at lower concentration. It was observed that the precipitation rate reached a minimum with increasing additive concentration.     

Temperature fluctuations in a LiNbO3 melt during crystal growth

The synthesis of calcium carbonate (CaCO₃) crystals from aqueous solutions containing sodium dodecyl sulfate (SDS), poly(N-vinyl-1-pyrrolidone) (PVP), or SDS/PVP complexes has been performed through a slow titration method. It was found that aragonite and calcite co-existed in the prepared crystals. The formation of aragonite in the precipitation systems without magnesium ions indicates that at ambient temperature ca. 26.0°C, initially formed amorphous CaCO₃ could also transfer into aragonite in the sedimentary phase, which indicates the controlling factor of organic additives in the nucleation and growth process of CaCO₃ crystals. The appearance of hexagonal crystals in the suspensible phase confirmed the hexagonal crystallization cell of vaterite, and revealed the colloidal-dispersion function of the SDS/PVP complex in the crystallization process of CaCO₃.     

Crystallization habit of calcium carbonate in presence of sodium dodecyl sulfate and/or polypyrrolidone

The synthesis of calcium carbonate (CaCO₃) crystals from aqueous solutions containing sodium dodecyl sulfate (SDS), poly(N-vinyl-1-pyrrolidone) (PVP) or SDS/PVP complexes has been performed through a slow titration method. It was found that aragonite and calcite coexisted in the prepared crystals. The formation of aragonite in the precipitation systems without magnesium ions indicates that at ambient temperature ca. 26.0°C, initially formed amorphous CaCO₃ could also transfer into aragonite in the sedimentary phase, which indicates the controlling factor of organic additives in the nucleation and growth process of CaCO₃ crystals. The appearance of hexagonal crystals in the suspensible phase confirmed the hexagonal crystallization cell of vaterite, and revealed the colloidal-dispersion function of the SDS/PVP complex in the crystallization process of CaCO₃.     

Fabrication of novel urchin-like architecture and snowflake-like pattern CuS

The interesting biomimetic morphologenesis of CuS, containing urchin-like architecture and snowflake-like pattern can be separately obtained via heating different solutions. In our case, ethanol or the mixed solvent of ethanol/H₂O containing CuCl₂ and CS₂ as raw materials in the presence of the surfactant additive cetyltrimethylammonium bromide (CTAB) have been used. The products were characterized by various techniques of XRD, SEM and ED. In the process, the solvent medium and the surfactant additive CTAB played very important roles in the formation of different biomimetic morphologies and the formation mechanisms were primarily discussed, respectively.     

Different shapes of spherical vaterite by photo-induced cis–trans isomerization of an azobenzene-containing polymer in a mixture of dimethyl sulfoxide and water

We studied the crystallization of CaCO₃ by the photoisomerization of azobenzene groups in poly[1-[4-[3-carboxy-4-hydroxyphenylazobenzenesulfonamido]-1,2-ethanediyl, sodium salt] (PAZO) in a mixture of dimethyl sulfoxide and water at 30 °C. The products were characterized by scanning electron microscopy (SEM), FT-IR, and powder X-ray diffraction (XRD) analysis. We observed that the different shapes of spherical vaterite particles were produced by the changes of configuration and polarity of the azobenzene groups in the polymer which resulted from photo-induced isomerization. The results indicate that the nucleation of primary particles of CaCO₃ was inhibited by in situ photo-induced cis–trans isomerization of PAZO. Therefore, we suggest that the shapes of the spherical vaterite can be effectively modified by photoisomerization of the azobenzene groups in the polymer at the initial stage of CaCO₃ crystallization.     

Growth of Na modified potassium lithium niobate crystal by the Czochralski method

Transparent Na modified potassium lithium niobate (Na_0.23K_2.60Li_1.82Nb_5.35O_15.70; NKLN) crystal was successively grown by the Czochralski method using RF induction heating from melt composition Na₂O:K₂O : Li₂O:Nb₂O₅=2:30:25:43 mol%. NKLN crystal showed a tetragonal tungsten bronze structure with lattice constants a=12.5446±0.0010 Å and c=4.0129±0.0005 Å at room temperature. The dielectric constant along the c-axis ε₃₃ showed a sharp maximum around 480 °C. Optical transmission edge was 370 nm and optical transmission spectra showed no absorption at wavelengths ranging from 380 to 800 nm. The structural and optical properties of NKLN were similar to those of the near stoichiometric KLN crystals. We believe that the growth of NKLN by the Czochralski method has an advantage for a large size and high-quality crystal.     

Synthesis and characterization of type-II textured tungsten disulfide thin films by vdWR process with Pb interfacial layer as texture promoter

The growth of type-II textured tungsten disulfide (WS₂) thin films by solid state reaction between the spray deposited WO₃ and gaseous sulfur vapors with Pb interfacial layer has been studied. X-ray diffraction (XRD) technique is used to measure the degree of preferred orientation ‘S’ and texture of WS₂ films. Scanning electron microscopy (SEM) and transmission electron microscopy techniques have been used to examine the microstructure and morphology. The electronic structure and chemical composition were studied using X-ray photoelectron spectroscopy (XPS). The use of Pb interfacial layer for the promotion of type-II texture in WS₂ thin films is successfully demonstrated. The presence of (0 0 3 l), (where l=1, 2, 3, …) family of planes in the XRD pattern indicates the strong type-II texture of WS₂ thin films. The crystallites exhibit rhombohedral (3R) structure. The large value of ‘S’ (1086) prompts the high degree of preferred orientation as well. The stratum of crystallites with their basal plane parallel to the substrate surface is seen in the SEM image. The EDS and XPS analyses confirm the tungsten to sulfur atomic ratio as 1:1.75. We purport that Pb interfacial layer enhances type-II texture of WS₂ thin films greatly.     

Mechanochemical metathesis synthesis and characterization of nano-structured MnV2O6·xH2O (x=2, 4)

A solid-state metathesis approach for the synthesis of hydrated MnV₂O₆·xH₂O (x=2, 4) materials driven by mechanochemical activation energy has been demonstrated. The metathesis pathway of forming the desired product is confirmed by the presence of high lattice energy by-product such as NaCl. The structural, optical, and chemical properties of the synthesized materials are examined by powder X-ray diffraction, X-ray photoelectron spectroscopy, thermo gravimetric analysis, scanning electron microscopy, transmission electron microscopy, and diffused reflectance measurements in the UV–vis range. The valence state of Mn and V was determined to be +2 and +5, respectively, for the title compounds and the bandgap values determined showed these materials are likely to be semiconductors.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.     

Textural properties of synthetic nano-calcite produced by hydrothermal carbonation of calcium hydroxide

The hydrothermal carbonation of calcium hydroxide (Ca(OH)₂) at high pressure of CO₂ (initial P_CO2=55 bar) and moderate to high temperature (30 and 90 °C) was used to synthesize fine particles of calcite. This method allows a high carbonation efficiency (about 95% of Ca(OH)₂–CaCO₃ conversion), a significant production rate (48 kg/m³ h) and high purity of product (about 96%). However, the various initial physicochemical conditions have a strong influence on the crystal size and surface area of the synthesized calcite crystals. The present study is focused on the estimation of the textural properties of synthesized calcite (morphology, specific surface area, average particle size, particle size distribution and particle size evolution with reaction time), using Rietveld refinements of X-ray diffraction (XRD) spectra, Brunauer–Emmett–Teller (BET) measurements, and scanning electron microscope (SEM) and transmission electron microscope (TEM) observations. This study demonstrate that the pressure, the temperature and the dissolved quantity of CO₂ have a significant effect on the average particle size, specific surface area, initial rate of precipitation, and on the morphology of calcium carbonate crystals. In contrast, these PTx conditions used herein have an insignificant effect on the carbonation efficiency of Ca(OH)₂.

Finally, the results presented here demonstrate that nano-calcite crystals with high specific surface area (S_BET=6–10 m²/g) can be produced, with a high potential for industrial applications such as adsorbents and/or filler in papermaking industry.     

A simple method to synthesize single-crystalline β-wollastonite nanowires

The single-crystalline β-wollastonite (β-CaSiO₃) nanowires were prepared via a simple hydrothermal method, in the absence of any template or surfactant using cheap and simple inorganic salts as raw materials. Xonotlite [Ca₆(Si₆O₁₇)(OH)₂] nanowires were first obtained after hydrothermal treatment at a lower temperature of 200 °C for 24 h, and after being calcinated at 800 °C for 2 h, xonotlite nanowires completely transformed into β-wollastonite nanowires and the wire-like structure was preserved. The synthesized β-wollastonite nanowires had a diameter of 10–30 nm, and a length up to tens of micrometers, and the single-crystalline monoclinic parawollastonite structured β-wollastonite was identified by XRD with the space group of P2₁/a and cell constants of a=15.42 Å, b=7.325 Å, c=7.069 Å and β=95.38°. A possible growth mechanism of β-wollastonite nanowires was also proposed. The advantages of this method for the nanowire synthesis lie in the high yield, low temperature and mild reaction conditions, which will allow large-scale production at low cost.     

Growth of nanofibrous barium carbonate on calcium carbonate seeds

Fibrous barium carbonate (BaCO₃/witherite) crystals 50–100 nm in diameter and several microns in length were grown on calcium carbonate (CaCO₃) seeds at temperatures as low as 4 °C. The BaCO₃ fibers were deposited onto calcite rhombs or CaCO₃ films using the polymer-induced liquid-precursor (PILP) process, which was induced with the sodium salt of polyacrylic acid (PAA). The structure and morphology of the resultant fibers were investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected-area electron diffraction (SAED), and polarized light microscopy (PLM). Fibers were successfully grown on calcite seeds of various morphologies, with a range of barium concentrations, and PAA molecular weight and concentration. Two categories of fibers were grown: straight and twisted. Both types of fibers displayed single-crystalline SAED diffraction patterns, but after examining high-resolution TEM lattice images, it was revealed that the fibers were in fact made up of nanocrystalline domains. We postulate that these nanocrystalline domains are well aligned due to a singular nucleation event (i.e., each fiber propagates from a single nucleation event on the seed crystal) with the nanocrystalline domains resulting from stresses caused by dehydration during crystallization of the highly hydrated precursor phase. These BaCO₃ fibers grown on calcite substrates further illustrate the robustness and non-specificity of the PILP process.     

Synthesis of AlN from Li3N and Al: Application to vapor phase epitaxy

We performed synthesis of AlN using Al and Li₃N. In this method, there are two problems that must be solved for obtaining single-phase AlN. One of them is suppression of Li₃AlN₂ formation and the other is precipitation of LiAl from the residual source materials during the cooling process. In the present work, we analyzed phase stability of products and found that AlN was stable at high temperatures and low Li–N/Al molar ratios. However, the products still contained LiAl and Al. Therefore, we examined the effectiveness of vapor phase epitaxy for separating AlN from the extra phase (LiAl and Al formed from residual source materials). From the experimental results, feasibility of vapor phase epitaxy was confirmed. That is, we can deposit only an AlN layer on a sapphire substrate by optimizing the growth conditions, i.e., temperature range above 1150 °C and Li–N/Al molar ratio less than 1.     

Preparation of CdS nanowires by the decomposition of the complex in the presence of microwave irradiation

A novel synthetic route for the preparation of CdS nanowires has been developed. CdS nanowires with a diameter of ca. 4 nm have been successfully prepared by the microwave irradiation of a complex of cadmium-1-pyrrlidine dithio carboxylic acid ammonium (C₅H₁₂N₂S₂, APDTC) [Cd(APDTC)₂]₂ in an ethylenediamine solution. The CdS nanowires were characterized by powder X-ray diffraction pattern, transmission electron microscopy (TEM), UV-Vis spectroscopy, diffuse reflection spectroscopy and PL spectroscopy.     

Role of non-stoichiometry in the cracking of oxide crystals

The cracking and stoichiometric deviations frequently observed in crystals of mixed oxides have generally been perceived to be unrelated phenomena. The present study pertains to the cracking in Czochralski grown crystals of three different materials, viz. CdWO₄, PbWO₄ and ZnWO₄. The results obtained on the single-crystal growth as well as on the thermal stability of melts of these materials and of their constituent oxides demonstrate, for the first time, that stoichiometric deviations manifest as cracks in the crystals. An important outcome of this investigation is that materials exhibiting a small degree of super-cooling with stable melting and solidification temperatures should be less prone to cracking.     

Hydrothermal synthesis of MoS2 nanowires

The MoS₂ nanowires with diameters of 4 nm and lengths of 50 nm were synthesized by a hydrothermal method using 0.36 g MoO₃ and 1.8 g Na₂S as precursors in 0.4 mol/l HCl solution at 260°C. The products are characterized by XRD, XPS, TEM, HTEM and BET. Results show that the as-prepared MoS₂ nanowires consist of 1–10 sulfide layers with BET surface areas of 107 m²/g. The possible reaction route and the formation mechanism of the MoS₂ nanowires are discussed. The effects of exterior conditions such as pH value, temperature, concentration of precursors and additives on the particle size and morphology of MoS₂ crystallites were investigated.     

Dual mineralization of dicalcium phosphate and hydroxyapatite formation on both sides of porous membrane: Alternating current induces pH-modulated crystal deposition

Dual mineralization on a porous membrane was carried out using an electrochemical approach. The porous membrane was interposed between a pair of glass cells, and calcium chloride (CaCl₂) and sodium hydrogenphosphate (Na₂HPO₄) solutions were separately injected into the cells. After inserting platinum electrodes into the cells, an alternating current with a sine waveform was applied for a given period of time. The resulting membrane was removed from the glass cells and rinsed with ultrapure water. The minerals formed on the membrane were analyzed by using spectroscopic methods such as scanning electron microscopy (SEM), infrared (IR) spectroscopy, and X-ray diffraction (XRD) and identified to be dicalcium phosphate and hydroxyapatite. It was noted that dicalcium phosphate formed on one side of the membrane, while hydroxyapatite was formed on the other side. Thus, dual mineralization could be successfully achieved on both sides of the porous membrane under an alternating current. This process of dual mineralization is very useful for the formation of versatile organic–inorganic hybrids and also for the regulation of the polymorphs on either side of a membrane.