Preparation of poly(hydroxyethyl methacrylate) and poly(hydroxypropyl methacrylate) latices

Hydroxyethyl methacrylate and hydroxypropyl methacrylate (both having extremely high solubilities in water) were polymerized in aqueous medium to obtain the respective polymer latices with a solid content as high as 10 wt.-%. The initial state of the polymerization is in solution rather than in dispersion, and the polymer product is sparingly soluble in the aqueous phase. The polymerization was carefully controlled to avoid forming hydrogel by using an oil soluble initiator and a mixture of sodium dodecyl sulfate and poly(vinyl alcohol). Solubilities of both monomers and polymers in water were also investigated.     

Creatinine imprinted poly(hydroxyethyl methacrylate) based cryogel cartridges

Creatinine imprinted cryogel (MIP) cartridge was prepared with functional monomer N-methacryloyl-(L)-histidinemethylester (MAH) under frozen conditions. Creatinine adsorption studies and selectivity of MIP cryogel were evaluated in aqueous solution and artificial urine sample. Maximum adsorbed amount of creatinine was calculated as 6.83 mg/g polymer for MIP cryogel. Langmuir and Freundlich adsorption isotherm models were used to investigate the adsorption behaviour of creatinine. In the artificial urine sample; recovery amounts of creatinine were found 34.7–46.2%. Creatinine imprinted cryogel (MIP) cartridge recognized creatinine, 4.58 and 4.37 times greater competitive molecules. MIP cryogel catridge was repeatedly used many times for adsorption desorption cycles.     

Characterisation of hydroxyapatite surface modified by poly(ethylene glycol) and poly(hydroxyethyl methacrylate) grafting

Hydroxyapatite (HA) has many applications in medicine as a biocompatible and bioactive biomaterial. Numerous studies have shown that modification of the HA surface can improve its biological and chemical properties. However, little is known about the surface properties of modified materials. In this paper the influence of organic polymers: polyethylene glycol (PEG) and polyhydroxyethyl methacrylate (pHEMA) on the surface properties and surface chemistry of hydroxyapatite (HA) is presented. The surface properties of modified HA were characterised by the FT-IR, XPS, BET, and zeta potential measurements. Specific surface area was determined by BET. Infrared and XPS spectra confirmed the presence of PEG and pHEMA on the surface of HA. The BET N₂ adsorption revealed slight changes in the HA surface chemistry after grafting modification. The surface chemical properties of the HA were considered to be based on the zeta potential. The decrease in zeta potential results in the increasing stability of the modified material and also in the reduction of bacterial adhesion. The reaction for surface modification of HA is proposed and described.     

Hydrogels of poly(hydroxyethyl methacrylate) and hydroxyethyl methacrylate—glycerol monomethacry-late copolymers

Hydrophilic three-dimensional polymer networks (hydrogels) were prepared from hydroxyethyl methacrylate (HEMA) and the copolymer HEMA and glycerol monomethacrylate (GMMA). The equilibrium water content of the hydrogels in water was investigated as a function of the initial dilution of the polymerization mixture, the type of solvent, and the hydrophilicity of the polymer. The initial dilution was found to have a decisive effect on the swelling or deswelling of hydrogels after the completion of the gel formation. With relatively less hydrophilic hydrogels, there is a critical initial dilution to produce the gel which does not swell or deswell in water after the gel formation. This “isovolumic” initial dilution shifts toward a higher dilution as the hydrophilicity of the hydrogels increases; however, when hydrophilicity of the polymer rises above a certain point, gels always swell in water. Permeability of oxygen through hydrogels was also studied.     

Modification of capillary electrophoresis capillaries by poly(hydroxyethyl methacrylate), poly(diethylene glycol monomethacrylate) and poly(triethylene glycol monomethacrylate)

Modification of capillary electrophoresis (CE) capillaries by poly(hydroxyethyl methacrylate) (poly(HEMA), poly(diethylene glycol monomethacrylate) (poly(DEGMA) and poly(triethylene glycol monomethacrylate) (poly(TEGMA), was studied. Methods based on physical adsorption of the modifier and on its chemical binding were compared on the basis of the electroosmotic flow (EOF) reproducibility, the EOF dependence on the pH, the symmetry of the peak of positively charged tyramine, the stability of the coating and the separation of standard and milk proteins in the modified capillaries. Reproducible coatings were obtained by chemical binding of the polymers to the capillary walls and by coating with a solution of a polymer, as also demonstrated by the atomic force microscopy.     

Cysteine functionalized poly(hydroxyethyl methacrylate) monolith for heavy metal removal

The aim of this study was to investigate the performance of monoliths composed of hydroxyethyl methacrylate (HEMA) to which N-methacryloyl-(L)-cysteine methyl ester (MAC) was polymerized for removal of heavy metal ions. Poly(HEMA-MAC) monolith was produced by bulk polymerization. Poly(HEMA-MAC) monolith was characterized by FTIR and scanning electron microscopy (SEM). The poly(HEMA-MAC) monolith with a swelling ratio of 89%, and containing 69.4 μmol MAC/g were used in the adsorption studies. Adsorption capacity of the monolith for the metal ions, i.e., Cu²⁺, Cd²⁺, Zn²⁺, Hg²⁺, and Pb²⁺ were investigated in aqueous media containing different amounts of the ions (10–750 mg/L) and at different pH values (3.0–7.0). The maximum adsorption capacities of the poly(HEMA-MAC) monolith were 68.2 mg/g for Zn²⁺, 129.2 mg/g for Cu²⁺, 245.8 mg/g for Pb²⁺, 270.2 mg/g for Hg²⁺, and 284.0 mg/g for Cd²⁺. pH significantly affected the adsorption capacity of MAC incorporated monolith. The competitive adsorption capacities were 587 μmol/g for Zn²⁺, 1646 μmol/g for Cu²⁺, 687 μmol/g for Pb²⁺, 929 μmol/g for Hg²⁺, and 1993 μmol/g for Cd²⁺. The chelating monolith exhibited the following metal ion affinity sequence on molar basis: Cd²⁺ > Cu²⁺ > Hg²⁺ > Pb²⁺ > Zn²⁺. The formation constants of MAC–metal ion complexes have been investigated applying the method of Ruzic. The calculated values of stability constants were 5.28 × 10⁴ L/mol for Cd²⁺, 4.16 × 10⁴ L/mol for Cu²⁺, 2.27 × 10⁴ L/mol for Hg²⁺, 1.98 × 10⁴ L/mol for Pb²⁺, and 1.25 × 10⁴ L/mol for Zn²⁺. Stability constants were increased with increasing binding affinity. The chelating monoliths can be easily regenerated by 0.1 M HNO₃ with higher effectiveness. These features make poly(HEMA-MAC) monolith a potential adsorbent for heavy metal removal.     

Synthesis and curing of poly(glycidyl methacrylate) nanoparticles

Glycidyl‐functional polymer nanoparticles [poly(glycidyl methacrylate) (PGMA)] were fabricated with microemulsion polymerization. The successful fabrication of PGMA nanoparticles was confirmed by Fourier transform infrared spectroscopy and transmission electron microscopy (TEM). A TEM image showed that the average diameter of the PGMA nanoparticles was approximately 10–28 nm and was fairly monodisperse. As the surfactant concentration increased, the average size of the nanoparticles decreased and approached an asymptotic value. A significant reduction of the nanoparticle size to the nanometer scale led to an enhanced number of surface functionalities, which played an important role in the curing reaction. The PGMA nanoparticles were cured with a low‐temperature curing agent, diethylene triamine, to produce ultrafine thermoset nanoparticles. The low‐temperature curing process was performed below the glass‐transition temperature of PGMA to prevent the coagulation and deformation of the nanoparticles. A TEM image indicated that the cured PGMA nanoparticles did not exhibit interparticle aggregation and morphological transformation during curing. The average size of the cured PGMA nanoparticles was consistent with that of the pristine PGMA nanoparticles © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2258–2265, 2005     

Dye attached poly(hydroxyethyl methacrylate) cryogel for albumin depletion from human serum

Cibacron Blue F3GA was immobilized on poly(hydroxyethyl methacrylate) cryogel and it was used for selective and efficient depletion of albumin from human serum. The poly(hydroxyethyl methacrylate) was selected as the basic component because of its inertness, mechanical strength, chemical and biological stability, and biocompatibility. Cibacron Blue F3GA was covalently attached to the poly(hydroxyethyl methacrylate) cryogel to produce poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel affinity column. The poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel was characterized with respect to gelation yield, swelling degree, total volume of macropores, Fourier Transform Infrared spectroscopy, and scanning electron microscopy. It was found that the maximum amount of adsorption (343 mg/g of dry cryogel) obtained from experimental results is very close to the calculated Langmuir adsorption capacity (345 mg/g of dry cryogel). The maximum adsorption capacity for poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel column was obtained as 950 mg/g of dry cryogel for nondiluted serum. The adsorption capacity decreased with increasing dilution ratios while the depletion ratio of albumin remained as 77% in serum sample. Finally, the poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel was optimized for using in the fast protein liquid chromatography system for rapid removal of the high abundant proteins from the human serum.     

On the preparation of stable poly(2-hydroxyethyl methacrylate) nanoparticles

A comprehensive experimental study of aqueous heterophase homopolymerization of 2-hydroxyetyl methacrylate revealed special conditions that must be fulfilled in order to obtain stable latex particles in the nanometer size range. The results clearly show that the formation and the stability of this kind of hydrophilic latex particle strongly depends on the hydrophobic-hydrophilic properties of both the initiating radicals and the stabilizers. Hydrophobic initiators in combination with sodium alkyl sulfate surfactants of proper chain lengths or ionic surface-active initiators lead to stable latex particles. In the latter case the particles keep their identity and spherical shape even after drying of the aqueous dispersion.     

Voltage-tunable volume transitions in nanoscale films of poly(hydroxyethyl methacrylate) surfaces grafted onto gold

Surface grafting of a polymerizable monomer onto Au was used to produce nanometer-scale planar hydrogel films with controllable volume. A self-assembled monolayer of 11-mercaptoundecanoic acid on a planar Au surface was activated through water-soluble carbodiimide and N-hyroxysuccinimide followed by reaction with 2-aminomethacrylate to produce a methacrylate-terminated surface layer, which readily polymerized under UV radiation in the presence of hydroxyethyl methacrylate monomer, ethylene glycol dimethacrylate cross-linker, and a photoinitiator. The reaction steps were characterized by external reflection mode Fourier transform IR spectroscopy. Under controlled UV exposure, thin (3 nm < d < 10 nm) hydrogel films were obtained from 1:1 ethanol/H(2)O. Surface plasmon resonance measurements were used to characterize both the synthesis of the hydrogel and the potential-induced volume changes. The nanometer-scale hydrogels thus produced undergo reproducible changes in thickness, when a potential is applied across the film. Thickness changes increasing with applied potential were obtained for both voltages in the range |V(appl)| 相似文献   

Morphological and spectroscopic analyses of poly(alkyl methacrylate)/poly(thiophene) composite nanoparticles prepared by dual initiation system

Poly(alkyl methacrylate)/poly(thiophene) (PAMA/PTh) core/shell nanoparticles were synthesized using a one-pot dual initiation system. A ferric chloride/hydrogen peroxide mixture and sodium vinyl sulfonate were used as an initiator couple and a reactive surfactant, respectively. In the dual initiation, process variables such as the concentration of reactive surfactant, monomer ratio, and monomer type were adjusted to control the particle size of PAMA/PTh core/shell nanoparticles from 192 to 1,172 nm. The inner structure of the core/shell nanoparticles was confirmed in their morphological transition from spherical particles to a crumpled sheath using a solvent extraction method and field-emission scanning electron microscopy. From the spectroscopic data, it was found that the UV-adsorption and fluorescent emission intensity of PAMA/PTh latexes increased with a decrease in the average particle size. The quantum efficiency of all the samples was approximately 12 % and was unaffected by the particle size.     

Antibacterial properties of novel poly(methyl methacrylate) nanofiber containing silver nanoparticles

Poly(methyl methacrylate) (PMMA) nanofiber containing silver nanoparticles was synthesized by radical-mediated dispersion polymerization and applied to an antibacterial agent. UV-vis spectroscopic analysis indicated that the silver nanoparticles were continually released from the polymer nanofiber in aqueous solution. The antibacterial properties of silver/PMMA nanofiber against both Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) bacteria were evaluated using minimum inhibitory concentration (MIC), the modified Kirby-Bauer method, and a kinetic test. The MIC test demonstrated that the silver/PMMA nanofiber had enhanced antimicrobial efficacy compared to that of silver sulfadiazine and silver nitrate at the same silver concentration.     

Preparation of poly(methyl methacrylate) grafted hydroxyapatite nanoparticles via reverse ATRP

Surface-initiated reverse atom transfer radical polymerization (reverse ATRP) technical was successfully employed to modify hydroxyapatite (HAP) nanoparticles with poly(methyl methacrylate) (PMMA). The peroxide initiator moiety for reverse ATRP was covalently attached to the HAP surface through the surface hydroxyl groups. Reverse ATRP of methyl methacrylate (MMA) from the initiator-functionalized HAP was carried out, and the end bromide groups of grafted PMMA initiated ATRP of MMA subsequently. Fourier transformation infrared (FTIR) spectroscopy, thermal gravimetric analysis (TGA) and transmission electron microscopy (TEM) were employed to confirm the grafting and to characterize the nanoparticle structure. The grafted PMMA gave HAP nanoparticles excellent dispersibility in MMA monomer. As the amount of grafted PMMA increased, the dispersibility of surface-grafted HAP and the compressive strength of HAP/PMMA composites were improved.     

Synthesis,structure, and properties of silver nanocomposite materials with poly(hydroxyethyl methacrylate) matrix

The mechanism of photoreduction of silver particles from colloidal solutions in 2-hydroxyethyl methacrylate, followed by its photopolymerization for preparing antirefl ection coatings, is considered.     

Surface modification of poly(2‐hydroxyethyl methacrylate) hydrogel for contact lens application

The present study examined poly(2‐hydroxyethyl methacrylate) (PHEMA)‐based hydrogels that have been extensively used in biomedical applications, including contact lens. In this research, we aimed to reduce adsorption of protein components from tears and bacterial deposition by surface modification of the hydrogel with different functional groups that included carboxylic acid, primary amine, and quaternary ammonium. The PHEMA was treated with a solution of sulfuric acid for partial hydrolysis of the HEMA ester groups to induce acid groups on the surface of the hydrogel. Carboxylic acid groups of the modified PHEMA were converted to primary amine and quaternary ammonium groups via carbodiimide chemistry. The surface physical and chemical properties of different samples were investigated by atomic force microscopy and X‐ray photoelectron spectroscopy, respectively. We conducted the bicinchoninic acid assay to evaluate protein deposition from artificial tear fluid on samples. Antibacterial properties of the modified hydrogels were investigated with a culture of Staphylococcus aureus, one of the major causes of eye infections. Our data showed that positively charged amine and ammonium groups efficiently resisted protein adsorption and bacterial deposition compared to alcohol and carboxylic acid groups.     

Water-compatible poly (hydroxyethyl methacrylate) polymer sorbent for miniaturized syringe assisted extraction of sulfonamides in milk

A simple, convenient, and economic self-assembly miniaturized syringe assisted extraction (mini-SAE) using poly (hydroxyethyl methacrylate) polymer (PHEMA) as sorbent coupled with liquid chromatography was proposed for rapid screening of sulfadiazine (SD) and sulfamonomethoxine (SMM) in milk. The water-compatible PHEMA was synthesized by reversible addition-fragmentation chain transfer precipitation polymerization using trithiocarbonate as chain transfer agent and methanol–water system as reaction medium. The obtained PHEMA sorbent showed good affinity to sulfonamides and was successfully applied as a special sorbent for a mini-SAE device for simultaneous extraction and isolation of SD and SMM in milk samples. Under the optimum condition, good linearity was obtained in a range of 7.0–700 ng g⁻¹ (r ≥ 0.9995) and the average recoveries of SD and SMM at three spiked levels were ranged from 85.6 to 100.3% with the relative standard deviations (RSD) ≤6.5%. The presented PHEMA-mini-SAE protocol could be potentially applied as an alternative tool for analyzing the residues of SAs in complicated biological samples.