Nanoparticle stability in semidilute and concentrated polymer solutions

The wetting of PDMS-grafted silica spheres (PDMS- g-silica) is connected to their depletion restabilization in semidilute and concentrated PDMS/cyohexane polymer solutions. Specifically, we found that a wetting diagram of chemically identical graft and free homopolymers predicts stability of hard, semisoft, and soft spheres as a function of the bulk free polymer volume fraction, graft density, and the graft and free polymer chain lengths. The transition between stable and aggregated regions is determined optically and with dynamic light scattering. The point of demarcation between the regions occurs when the graft and free polymer chains are equal in length. When graft chains are longer than free chains, the particles are stable; in contrast, the particles are unstable when the opposite is true. The regions of particle stability and instability are corroborated with theoretical self-consistent mean-field calculations, which not only show that the grafted brush is responsible for particle dispersion in the complete wetting region but also aggregation in the incomplete wetting region. Ultimately, our results indicate that depletion restabilization depends on the interfacial properties of the nanoparticles in semidilute and concentrated polymer solutions.     

Spectroscopic and Discharge Studies on Graphene Oxide Doped PVA/PVP Blend Nanocomposite Polymer Films

Graphene oxide (GO) nanoparticles were synthesized by modified Hummers method. The synthesized GO nanoparticles were incorporated in polyvinyl alcohol/polyvinyl pyrrolidone (PVA/PVP) blend polymers for the preparation of nanocomposite polymer films by solution cast technique. Different characterizations such as XRD, UV–Vis and FTIR were carried-out on to the prepared nanocomposite polymer films. The thermal analysis of the films was studied by DSC. The morphology of PVA/PVP:GO polymer films confirms GO was exfoliated within the PVA/PVP matrix and also reveals the heterogeneous phase of nanocomposite polymer electrolyte systems. From the conductivity studies the highest conductivity of PVA/PVP: GO (0.45: 0.3) was found to be 8.05 × 10^–4 S/cm at room temperature. Solid state battery has been fabricated with the configuration of Mg⁺/(PVA/PVP:GO)/(I₂ + C + electrolyte) and its cell parameters were calculated for a constant load of 100 kΩ.     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

The temperature effect on electrokinetic properties of the silica–polyvinyl alcohol (PVA) system

The influence of polyvinyl alcohol (PVA) adsorption on the structure of the diffuse layer of silica (SiO₂) in the temperature range 15–35 °C was examined. The microelectrophoresis method was used in the experiments to determine the zeta potential of the solid particles in the absence and presence of the polymer. The adsorption of PVA macromolecules causes the zeta potential decrease in all investigated SiO₂ systems. Moreover this, decrease is the most pronounced at the highest examined temperature. Obtained results indicate that the conformational changes of adsorbed polymer chains are responsible for changes in electrokinetic properties of silica particles. Moreover, the structure of diffuse layer on the solid surface with adsorbed polymer results from the following effects: the presence of acetate groups in PVA chains, the blockade of silica surface groups by adsorbed polymer and the shift of slipping plane due to macromolecules adsorption.     

Solution of telechelic ionomers in water/AOT/oil (w/o) microemulsions: a static and dynamic light scattering study

Static and quasielastic light-scattering measurements of endsulfonated polyisoprene in a water in oil (w/o) microemulsions were used to characterize the structure and diffusion properties of this complex system. The hydrophilic end groups of the polymer stick to the surfactant covered oil/water interface, thus bridging the water droplets. This structure formation decreases the mobility of the aqueous nanodroplets and polymer molecules. At interdroplet distances larger than the end-to-end distance of the ionomer chain a decrease of the osmotic modulus is observed. It can be explained by a depletion force of free ionomer chains acting on the nanodroplets. With increasing polymer concentration structure formation of the microemulsion is observed at nanodroplet concentrations where the ionomer chains just fit the average separation of two nanodroplets.     

Interactions between colloidal particles induced by polymer brushes grafted onto the substrate

We investigate the interaction energy between two colloidal particles on or immersed in nonadsorbing polymer brushes grafted onto the substrate as a function of the separation of the particles by the use of a self-consistent-field theory calculation. Depending on the colloidal size and the penetration depth, we demonstrate the existence of a repulsive energy barrier of several kBT, which can be interpreted by separating the interaction energy into three parts: colloid-polymer interfacial energy, entropic contribution due to "depletion zone" overlap of colloidal particles, and entropic elastic energy of grafted chains by the compression of particles. The existence of a repulsive barrier which is of entirely entropic origin can lead to kinetic stabilization of the mixture rather than depletion flocculation or phase separation. Therefore, the present result may suggest an approach for controlling the self-assembling behavior of colloids for the formation of target structures, by tuning the colloidal interaction on the grafting substrate under appropriate selection of colloidal size, effective gravity (influencing the penetration depth), and brush coverage density.     

SPEEK/PVA-AgNPs复合膜的制备与表征

首先,以磺化聚醚醚酮(SPEEK)为光敏自由基载体,以聚乙烯醇(PVA)为分散稳定剂,制备了具有光生自由基功能的SPEEK/PVA高分子膜;然后,通过在SPEEK/PVA膜上紫外光诱导Ag+还原生成纳米银颗粒(AgNPs),从而得到SPEEK/PVA-AgNPs复合膜。采用紫外可见分光光度计(UV-Vis)、扫描电镜(SEM)、能谱仪(EDS)、X射线光电子能谱分析(XPS)及傅里叶变换红外光谱(FT-IR)等手段对SPEEK/PVA-AgNPs材料进行了表征。结果显示:生成的银颗粒为纳米级,较均匀地分布在SPEEK/PVA高分子膜表面,SPEEK/PVA-AgNPs复合膜整体呈现棕色;形成的银纳米颗粒具有较完整的晶型,且价态分析显示其为单质。     

Effect of grafting on nanoparticle segregation in polymer/nanoparticle blends near a substrate

Nanoparticles in polymer films have shown the tendency to migrate to the substrate due to an entropic-based attractive depletion interaction between the particles and the substrate. It is also known that polymer-grafted nanoparticles show better dispersion in a polymer matrix. Here, molecular dynamics simulations are employed to study the effect of grafting on the nanoparticle segregation to the substrate. The nanoparticles were modeled as spheres and the polymers as bead-spring chains. The polymers of the grafts and the matrix are identical in nature. For a purely repulsive system, the nanoparticle density near the surface was found to decrease as the length of grafted chains and the number of grafts increased and in the bulk, the nanoparticles are well-dispersed. Whereas, in case of attractive systems with interparticle interactions on the order of thermal energy, the nanoparticles segregated to the substrate even more strongly, essentially forming clusters on the wall and in the bulk. However, due to the presence of grafted chains on the nanoparticles, the clusters formed in the bulk are structurally anisotropic. The effect of grafts on nanoparticle segregation to the surface was found to be qualitatively similar to the purely repulsive case.     

Synthesis and stabilization of Prussian blue nanoparticles and application for sensors

Prussian blue (PB) nanoparticles were synthesized by two methods from FeCl2 and K3Fe(CN)6 and from FeCl3 and K3Fe(CN)6 based on the method published by Fiorito et al., and stabilized by different polymers like polyvinyl alcohol (PVA), polyvinyl pyrrolidone (PVP), polyallylamine hydrochloride (PAH), polydiallyl-dimethyldiammonium chloride (PDDA) and polystyrene sulfonate (PSS). The effect of the monomer/Fe3+ ratio was studied regarding the average particle size and zeta-potential. The forming PB structure was checked by X-ray diffraction. The stabilization was successful for every applied polymer, but the average particle size significantly differs. Particle size distributions were determined by Malvern type nanosizer equipment and by transmission electron microscope (TEM) and zeta potential values were determined for the obtained stabile samples. The results revealed that by using FeCl2 and K3Fe(CN)6 for PB preparation particles with narrow size distribution and average diameter of 1.7 nm occurred but stabilization was necessary. By the other method the dispersion was stabile with 182 nm particles but the particle size exponentially decreased to 18 nm with increasing PVP concentration. Ultrathin nanofilms were prepared on glass support by the alternating layer-by-layer (LbL) method from PB particles and PAH. The morphology of the prepared films was investigated also by AFM. The films were immobilized on interdigitated microsensor electrodes (IME) and tested in sensing hydrogen peroxide and different acids like acetic acid, hydrochloric acid vapors.     

Control of the Colloidal Stability of Polymer-Grafted-Silica Nanoparticles Obtained by Atom Transfer Radical Polymerization

Polymer chains are grafted from silica nanobeads. The method consists in grafting first the initiator molecules on the silica surface. Then, the polymerization of styrene or n-butyl methacrylate using Atom Transfer Radical Polymerization, is conducted. The nanoparticles are kept in solution during the whole process to avoid irreversible aggregation. The state of dispersion of the grafted silica nanoparticles is followed by Small Angle Neutron Scattering, as well as the quantity and the spatial organisation of the polymer. This is done during the functionalisation and the polymerization, but also after purification where free polymer chains are eliminated. This permits to reach a quantitative level of SANS analysis from these purified particles, which is compared to chemical data given by Size Exclusion Chromatography and Thermogravimetric analysis.     

Steric and bridging interactions between two plates induced by grafted polyelectrolytes

If colloidal particles are grafted with a polymer, then the grafted chains can provide steric repulsion between them. If some of the grafted polymer chains are also adsorbed to a second particle, then a bridging force is generated as well. For uncharged plates and polymer, the following contributions to the free energy of the system have been taken into account in the calculation of the interaction force: (i) the Flory-Huggins expression for the mixing free energy of the grafted chains with the liquid; (ii) the entropy loss due to the connectivity of the polymeric segments; (iii) the van der Waals interactions between the segments and the plates; and (iv) the free energy of adsorption of the polymer segments of the grafted chains on the other plate. For charged plates, the electrostatic free energy as well as the free energy of the electrolyte are included in the total free energy of the system. By minimizing the free energy with respect to the segment concentration and, when it is the case, with respect to the electrical potential, equations for the segment number density distribution and for the electrical potential are obtained, on the basis of which the interactions between two plates grafted with polymer chains that can be also adsorbed on the other plate were calculated. The interaction thus obtained includes steric and bridging forces.     

Phase behavior of a blend of polymer-tethered nanoparticles with diblock copolymers

Using the self-consistent field theory (SCFT), we investigate the phase behavior of a mixture of diblock copolymers and nanoparticles with monodisperse polymer chains tethered to their surfaces. We assume the size of the nanoparticles to be much smaller than that of the attached polymer chains and therefore model the particles with their grafted polymer "shell" as star polymers. The polymer chains attached to the particles are of the same species as one of the blocks of the symmetric diblock copolymer. Of primary interest is how to tune the shell of the particle by changing both the length and number of tethered polymers in order to achieve higher loading of nanoparticles within an ordered structure without macrophase separation occurring. We find that the phase behavior of the system is very sensitive to the size of the particle including its tethered shell. The region of microphase separation is increased upon decreasing the star polymer size, which may be achieved by shortening and/or removing tethered polymer chains. To explore the possible structures in these systems we employ SCFT simulations that provide insight into the arrangement of the different species in these complex composites.     

Immobilization of polymer-protected metal colloid catalysts by the formation of polymer hydrogen bond complexes

poly(N-vinyl-2-pyrrolidone)-(PVP) and polyvinyl alcohol-(PVA) protected nanoscopic noble metal colloidal catalysts were immobilized to prepare the corresponding heterogeneous catalysts by forming polymer hydrogen bond complexes of polyacrylic acid (PAA) with PVP or PVA. A PVP–PAA–Pd catalyst was found to be very active and selective for the partial hydrogenation of cyclopentadiene to cyclopentene.     

Effect of nano‐size nodular structure induced by CNT‐promoted phase separation on the fabrication of superhydrophobic polyvinyl chloride films

The nonsolvent‐induced phase separation (NIPS) method was employed to fabricate the porous films based on polyvinyl chloride loaded with carbon nanotubes (CNTs). The combinational addition of CNTs and a proper nonsolvent (ethanol) resulted in a porous surface layer with the nano‐size nodular structure possessing an exact superhydrophobic behavior (water contact angle [WCA] = 157° and sliding angle [SA] <5°). The size of PVC nodules at the surface layer varies in the range of 200 to 800 nm depending on the nonsolvent concentrations, and polymer molecular weight. The effects of various nonsolvent concentrations as well as PVC molecular weight on the surface properties of the films were also investigated. Morphological and roughness analyses revealed the pronounced role of PVC molecular weight on the size of nodules, and the structural uniformity of the surface morphology based on the thermodynamic parameters such as relaxation time and dynamic of polymer chains. The concurrent use of CNTs and nonsolvent led to promote the NIPS process due to the nucleating role of CNTs, which were localized within the polymer‐rich phase leading to an ultra‐fine and packed nodular surface structure. Transmission electron microscopy results also proved the very well dispersion quality of CNTs. Glass transition temperature of PVC was also assessed, and the results were correlated to the associating ability of CNTs with polymer chains during the phase separation process. Overall, the promising potential of CNT/ethanol combination on the surface porosity and hydrophobicity of PVC nanocomposite films was revealed in this study, which could further extend its application window.     

Effect of bidispersity in grafted chain length on grafted chain conformations and potential of mean force between polymer grafted nanoparticles in a homopolymer matrix

In efforts to produce polymeric materials with tailored physical properties, significant interest has grown around the ability to control the spatial organization of nanoparticles in polymer nanocomposites. One way to achieve controlled particle arrangement is by grafting the nanoparticle surface with polymers that are compatible with the matrix, thus manipulating the interfacial interactions between the nanoparticles and the polymer matrix. Previous work has shown that the molecular weight of the grafted polymer, both at high grafting density and low grafting density, plays a key role in dictating the effective inter-particle interactions in a polymer matrix. At high grafting density nanoparticles disperse (aggregate) if the graft molecular weight is higher (lower) than the matrix molecular weight. At low grafting density the longer grafts can better shield the nanoparticle surface from direct particle-particle contacts than the shorter grafts and lead to the dispersion of the grafted particles in the matrix. Despite the importance of graft molecular weight, and evidence of non-trivial effects of polydispersity of chains grafted on flat surfaces, most theoretical work on polymer grafted nanoparticles has only focused on monodisperse grafted chains. In this paper, we focus on how bidispersity in grafted chain lengths affects the grafted chain conformations and inter-particle interactions in an implicit solvent and in a dense homopolymer polymer matrix. We first present the effects of bidispersity on grafted chain conformations in a single polymer grafted particle using purely Monte Carlo (MC) simulations. This is followed by calculations of the potential of mean force (PMF) between two grafted particles in a polymer matrix using a self-consistent Polymer Reference Interaction Site Model theory-Monte Carlo simulation approach. Monte Carlo simulations of a single polymer grafted particle in an implicit solvent show that in the bidisperse polymer grafted particles with an equal number of short and long grafts at low to medium grafting density, the short grafts are in a more coiled up conformation (lower radius of gyration) than their monodisperse counterparts to provide a larger free volume to the longer grafts so they can gain conformational entropy. The longer grafts do not show much difference in conformation from their monodisperse counterparts at low grafting density, but at medium grafting density the longer grafts exhibit less stretched conformations (lower radius of gyration) as compared to their monodisperse counterparts. In the presence of an explicit homopolymer matrix, the longer grafts are more compressed by the matrix homopolymer chains than the short grafts. We observe that the potential of mean force between bidisperse grafted particles has features of the PMF of monodisperse grafted particles with short grafts and monodisperse grafted particles with long grafts. The value of the PMF at contact is governed by the short grafts and values at large inter-particle distances are governed by the longer grafts. Further comparison of the PMF for bidisperse and monodisperse polymer grafted particles in a homopolymer matrix at varying parameters shows that the effects of matrix chain length, matrix packing fraction, grafting density, and particle curvature on the PMF between bidisperse polymer grafted particles are similar to those seen between monodisperse polymer grafted particles.     

Synthesis of functional graft copolymers by solution copolymerization and their evaluation as dispersants in nonaqueous phase dispersion polymerization

The poly(HEMA‐co‐MMA‐g‐PMMA) graft copolymer was prepared with a poly(methyl methacrylate) (PMMA) macromonomer, 2‐hydroxyethyl methacrylate (HEMA), and methyl methacrylate (MMA), and its application as a dispersant for the nonaqueous phase dispersion polymerization of polystyrene (PST) was investigated. Monodisperse PST particles were obtained with two‐dimensionally tailored graft copolymers, with the number of grafted chains controlled and the polar component (HEMA) in the backbone chains balanced. As for the reactor, a stirred vessel with moderate agitation yielded uniform polymer particles, whereas sealed glass ampules with an overturning motion yielded broader size distributions. Increasing the polarity of the solvent in the continuous phase yielded smaller polymer particles with a gradual deterioration of monodispersity. Uniform polymer particles with a coefficient of variation of less than 6% were obtained up to 30 wt % solid contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1788–1798, 2003     

MICRON CORE-SHELL PARTICLES PREPARED BY GRAFTING POLYMERIZATION OF METHYL METHACRYLATE FROM NARROW DISPERSE SURFACE OF CHLOROMETHYLATED POLYDIVINYLBENZENE VIA ATRP

Grafting of poly(methyl methacrylate) from narrow disperse polymer particles by surface-initiated atom transfer radical polymerization (ATRP) was investigated. Polydivinylbenzene (PDVB) particles were prepared by dispersion polymerization with poly(N-vinyl pyrrolidone) (PVP) as the stabilizer. Chloromethylated PDVB was used as initiating core sites for subsequent ATRP of methyl methacrylate with CuBr/bpy as catalyst system. It was found that poly(methyl methacrylate) was grafted not only from the particle surfaces but also from within a thin shell layer, leading to particles size increases from 2.38-3.00μm with a core-shell structure particles. The grafted core-shell particles were characterized with FTIR, SEM, DSC.     

The displacement of adsorbed polymer from silica surfaces by the addition of a nonionic surfactant

The adsorption of polyvinyl alcohol and Synperonic NP8 (nonyl phenol ethoxylate with an average of eight ethylene oxide groups per molecule) on fumed silica has been studied at various pH values. This was followed by an investigation of the competitive adsorption of NP8 and PVA. It was shown that NP8 can displace the polymer from the silica. This was attributed to a higher adsorption energy for the NP8 molecule compared with the value of the individual adsorbed PVA segments. Sediment volume experiments showed that the addition of NP8 to a colloidally stable silica dispersion with adsorbed PVA can induce flocculation as a result of displacement of some or all of the PVA chains from the surface. Initially the adsorption of the NP8 molecules caused an increase in the hydrophobic interaction (resulting in the flocculation) between the alkyl phenol groups which are oriented towards the bulk solution (since the PEO chains preferentially adsorb on the silica surface). Restabilisation at higher NP8 concentrations occur through the formation of bilayers with the PEO chains now dangling in solution.     

Photoinduced shape fixity and thermal-induced shape recovery properties based on polyvinyl alcohol bearing coumarin

In this paper, polyvinyl alcohol (PVA) bearing coumarin with different degrees of substitution (DS) are synthesized by esterifying hydroxyl of PVA with 7-carboxylmethoxycoumarin. The grafted polymer has photosensitive property and presents photocrosslinking due to the photodimerization between pendant coumarin groups, which affords PVA–coumarin sample photoinduced shape fixity properties. PVA–coumarin can be cross-linked after being illuminated under UV light of 360 nm; this provides the possibility that the sample has shape memory properties only if the cross-linking extent is suitable. The shape memory properties were induced by thermal as most shape memory polymer do. In fact, the shape fixity and recovery has strong relationship with DS, irradiation time, and thickness of sample. The effect of DS on the grafted polymer structure and properties has been studied by differential scanning calorimetry, thermogravimetric analysis, and UV spectra.     

Analysis of the grafting process of PVP on a silicon surface by AFM and contact angle

Silicon wafers have been silylated with VTMS (vinyltrimethoxysilane) and hydrolyzed. Subsequently, PVP (polyvinyl pyrrolidone) was grafted onto the silylated surface by two different techniques: the grafting-through (GT) and the grafting-onto techniques (GO). The measurement of contact angles along with the topography analysis by atomic force microscopy (AFM) has allowed monitoring the different stages of the process and the temporal evolution of polymer grafting. The results have demonstrated the feasibility of both methods of grafting but have shown that the GT method gives a higher density of polymer-grafted chains. The AFM technique in adequate liquid environments has been proven to permit the surface density of chains to be distinguished by both methods and to estimate the length of the resulting PVP chains.