Multielemental analysis in small amounts of environmental reference materials with inductively coupled plasma mass spectrometry

The lowest possible sample weight for performing multielemental trace element analysis on environmental and biological samples by ICP-MS has been investigated. The certified reference materials Bovine Liver NIST SRM 1577b, Human Hair NCS DC 73347 and Oriental Tobacco Leaves CTA-OTL-1 were applied at sample weights (1, 5, 20 and 50 mg aliquots, n = 10) which were significantly lower than those recommended with most recoveries in the range of 95–110%. Samples were digested in a mixture of nitric acid, hydrogen peroxide and hydrogen fluoride by closed-vessel microwave digestion. Multielemental analysis was performed with an optimized ICP-QMS method. Aqueous standard solutions were applied for external calibration with rhodium as the internal standard element. The detection limits varied between 0.02–¶0.38 μg/g for Li, Na, Cr, Mn, Ni, Cu, Zn, Sr, Cd, Ba and Pb, and up to 1.92 μg/g for Mg, Al, Ca, Fe and Ni. Digested human plasma samples were spiked with multielemental solution (0.5–10 μg/L) to test the analytical method and the recoveries were 95–105% for most analytes. Our results show that in the case of homogeneous SRMs it is possible to use them in very low amounts (1–5 mg) for method development and quality control.     

Determination of trace amounts of some metals in samples with high salt content by atomic absorption spectrometry after cobalt-diethyldithiocarbamate coprecipitation

A method for determination of trace amounts of Cu, Fe, Pb, Mn, Zn, Cd, Ni, Bi and Cr in aqueous solutions by flame atomic absorption spectrometry after coprecipitation by using a combination of sodium diethyldithiocarbamate as a chelating agent and cobalt as a carrier element was introduced. Different factors including amounts of reagents, pH of sample solution, standing time, sample volume for the precipitation and matrix effects were examined. Under selected conditions, the relative standard deviation of the combined method of sample treatment, coprecipitation and determination with flame AAS (n = 9) is generally about 3.5-6.9%; the limits of detection (3 s, n = 20) for the analytes were found to be between 4 and 64 microg 1(-1). The procedure was applied to the analysis of sea water and dialysis concentrate samples with quantitative recovery, > or =95%.     

New fluorimetric method of liquid chromatography for the determination of the neurotoxin domoic acid in seafood and marine phytoplankton

Domoic acid (DA) is a neurotoxic amino acid that is responsible for the human toxic syndrome, amnesic shellfish poisoning (ASP). A new rapid, sensitive liquid chromatographic (LC) method has been developed for the determination of DA in various marine samples. DA in marine biological materials was derivatised with 4-fluoro-7-nitro-2,1,3-benzoxadiazole (NBD-F) and analysed using isocratic reversed-phase LC with fluorimetric detection. The calibration, based on standard DA solutions, was linear in the range 0.04-2 microg/ml (r2=0.998) and the detection limit (3:1, signal/noise) was better than 1 ng/ml. Using the certified reference material (MUS-1B), recoveries of DA from shellfish tissue were >95% (n=5). When a strong anion exchange SPE cartridge was used for sample clean-up the detection limit was 6 ng DA/g mussel tissue. Good reproducibility was achieved with RSD values ranging from 3% for 8 microg DA/g (n=5), to 5% for 0.04 microg DA/g (n=5). This new method was successfully applied to the determination of DA in naturally contaminated shellfish and in marine phytoplankton cultures of Pseudonitzschia sp.     

Determination of total mercury and methylmercury in human hair by graphite-furnace atomic absorption spectrophotometry using 2,3-dimercaptopropane-1-sulfonate as a complexing agent.

For the determination of total mercury in hair, an amount (25.0 mg) of hair sample was digested with conc. HNO3 (400 microl) at 90 degrees C for 10 min in a 7-ml teflon microreaction vessel. After digestion, the pH of the acidic hair mixture was adjusted to 5.0-6.0 by NaOH and was then passed through a clean-up Sep-Pak C18 cartridge. To the eluate, 2,3-dimercaptopropane-1-sulfonate (DMPS) and sodium acetate buffer (pH = 6.0) were added to form a mercury-DMPS complex. This complex was preconcentrated on two Sep-Pak C18 cartridges in series, and each cartridge was eluted with methanol and adjusted to 2.00 ml. A portion (50 microl) was introduced into a graphite cuvette and then atomized according to a temperature program. The method detection limit (MDL, 3sigma) was 0.064 (microg g(-1)); the calibration graph was linear up to 7.52 microg g(-1). Good accuracies were obtained when testing two human hair certified reference materials (GBW 09101 and BCR-397). Six real samples were analyzed, and the recoveries were 95.8 - 98.2% with a relative standard deviation (RSD, n = 3) < 2.1%. For the determination of methylmercury (CH3Hg+), 25.0 mg of hair sample was extracted with 2.0 mol dm(-3) HCl (1.0 ml) by ultrasonicating for 1 h. The supernatant solution was used for CH3Hg+ analysis and the hair residue was used for the analysis of inorganic mercury (Hg2+). The MDL of CH3Hg+ was 0.068 microg g(-1); the calibration graph was linear up to 6.00 microg g(-1). Six real samples were analyzed, and the recoveries were 96.0-99.2% with RSD (n = 3) < 2.3%. The sum of the concentrations of CH3Hg+ and Hg2+ was very close to that of the total mercury measured with a relative error within 3.6%. The proposed method can be accurately applied to the measurement of CH3Hg+, Hg2+, and total mercury in hair samples.     

Determination of bisphenol A in sewage effluent and sludge by solid-phase and supercritical fluid extraction and gas chromatography/mass spectrometry

Methods have been developed for the determination of bisphenol A (BPA) residues in municipal sewage and sludge samples. BPA in wastewater samples was enriched with a C18 solid-phase extraction cartridge, eluted with acetone, and converted to the pentafluoropropionyl derivative. For sludge samples, BPA was acetylated and extracted with supercritical carbon dioxide. In both cases, BPA-d16 was used as a surrogate to monitor extraction efficiency. Final analyses of derivatized sample extracts were performed by gas chromatography/mass spectrometry operating in the electron impact mode. For water samples, mean recoveries and standard deviations were 89 +/- 6, 94 +/- 4, and 85 +/- 7% at fortification levels of 1, 0.1, and 0.025 microg/L, respectively, with a method detection limit of 0.006 microg/L. For solid waste samples, mean recoveries and standard deviations were 93 +/- 5 and 92 +/- 6% at fortification levels of 2.5 and 0.25 microg/g, respectively, and the method detection limit was 0.05 microg/g. For the Canadian samples under investigation, concentrations of BPA ranged from 49.9 to 0.031 microg/L in sewage influent and effluent, and from 36.7 to 0.104 microg/g in sludge.     

Application of matrix solid-phase dispersion and liquid chromatography–mass spectrometry to fungicide residue analysis in fruits and vegetables

A method based on matrix solid-phase dispersion (MSPD) and liquid chromatography-electrospay ionization-mass spectrometry used to analyze fifteen fungicide residues in fruits and vegetables is described. The method required only 0.5 g of sample, C(18)-bonded silica was used as dispersant sorbent, and ethyl acetate was used as eluting solvent. Fortified recoveries in apple, orange, banana, lettuce, grape and tomato samples ranged from 71% to 102% and relative standard deviations were less than 13% with fortified levels of 0.03-1.5 mg kg(-1). Detection and quantification limits were 1 approximately 30 microg kg(-1) and 4 approximately 100 microg kg(-1), respectively, with linear calibration curves extending up to 15 mg kg(-1). The analytical characteristics of MSPD compared very favorably with those found for a classical multiresidue method: the quick, easy, cheap, effective, rugged, and safe (QuEChERS) method. The method was applied to determine the fungicides in real samples. Liquid chromatography-tandem mass spectrometry (LC-MS-MS) was used as confirmatory tool for positive samples.     

Atomic absorption spectrometric determination of Cd(II), Mn(II), Ni(II), Pb(II) and Zn(II) ions in water,fertilizer and tea samples after preconcentration on Amberlite XAD-1180 resin loaded with l-(2-pyridylazo)-2-naphthol

A new chelating resin, 1-(2-pyridylazo)-2-naphthol (PAN) coated Amberlite XAD-1180 (AXAD-1180), was prepared and used for the preconcentration of Cd(II), Mn(II), Ni(II), Pb(II) and Zn(II) ions prior to their determination by flame atomic absorption spectrometry (FAAS). The optimum pH for simultaneous retention of the elements and the best elution means for their simultaneous elution were pH 9.5 and 3 M HNO₃, respectively. The sorption capacity of the resin was found to be 5.3 mg/g for Cd and 3.7 mg/g for Ni. The detection limits for Cd(II), Mn(II), Ni(II), Pb(II) and Zn(II) were 0.7, 10, 3.1, 29 and 0.8 μg/L, respectively. The effects of interfering ions for quantitative sorption of the metal ions were investigated. The preconcentration factors of the method were in the range of 10–30. The recoveries obtained were quantitative (≥95%). The standard reference material (GBW07605 Tea sample) was analysed for accuracy of the described method. The proposed method was successfully applied to the analysis of various water, urea fertilizer and tea samples. The article is published in the original.     

Automated microwave digestion of certifiable color additives for determination of mercury by cold vapor atomic absorption spectrometry

A procedure using an automated microwave flow digestion technique was developed and validated for the digestion of samples of certifiable color additives before mercury determination by cold vapor atomic absorption spectrometry. Recovery studies were performed by spiking most of the color additives subject to batch certification by the U.S. Food and Drug Administration with inorganic mercury (HgNO3) and with organic mercury (CH3HgCl). Successful recoveries of 72-113% Hg added at the 1 microg/g level were obtained. A method detection limit of 0.2 microg Hg/g was estimated from a Hg-spiked FD&C Yellow No. 6 sample. At the specification level of 1 ppm Hg (1 microg Hg/g), the 95% confidence interval was +/- 0.2 ppm (0.2 microg Hg/g).     

顶空气相色谱法测定氟尼辛葡甲胺原料药中有机溶剂残留量

建立了氟尼辛葡甲胺原料药中乙酸乙酯、甲醇、异丙醇、乙醇和乙腈有机溶剂残留量的顶空气相色谱分析方法。以HP-FFAP色谱柱(30 m×0.32 mm×1.0 μm)为分离柱,火焰离子化检测器检测,外标法定量,并考察了顶空平衡温度、平衡时间等对残留有机溶剂测定的影响。实验结果表明,在顶空平衡温度为90 ℃、平衡时间为30 min条件下获得较好的定量结果。乙酸乙酯、甲醇、异丙醇、乙醇和乙腈的线性范围分别为0.40～7.93 mg/L (r=0.9998)、7.32～146.48 mg/L (r=0.9996)、4.53～90.61 mg/L (r=0.9999)、3.62～72.32 mg/L (r=0.9998)和2.31～46.24 mg/L (r=0.9996);平均回收率范围为95.96%～100.31%,精密度(以相对标准偏差计,n=6)为1.97%～3.28%;检出限分别为0.08、0.9、0.2、0.4和0.3 mg/L。利用该方法对实际样品氟尼辛葡甲胺原料药中有机溶剂残留量进行了检测。结果表明,该样品中含有异丙醇和乙醇,其含量分别为177.44 μg/g与69.32 μg/g。本方法快速、灵敏、准确,适用于氟尼辛葡甲胺原料药中残留溶剂的检测。     

气相色谱-质谱法同时测定化妆品中19种邻苯二甲酸酯

建立了同时测定化妆品中19种邻苯二甲酸酯的气相色谱-质谱(GC-MS)方法。样品经二氯甲烷超声提取后,用硅胶-中性氧化铝(2:3, m/m)混合填料固相小柱保留、乙酸乙酯-正己烷(8:2, v/v)洗脱等步骤净化后,采用GC-MS对19种目标物进行定性、定量分析。采用保留时间与特征离子丰度比共同进行定性分析,减少了复杂样品基质中的干扰。在优化的实验条件及0.1、0.5、2.0 μg/g的添加水平下,平均加标回收率为72.2%～110.9%,其中加标水平为0.1 μg/g的相对标准偏差(RSD, n=6)小于10.3%;方法检出限(以3倍标准偏差计)为0.0065 μg/g(邻苯二甲酸二异戊酯)～0.062 μg/g(邻苯二甲酸二异丁酯)之间。应用该方法检测了6种化妆品中19种PAEs的含量。该方法可推广用于多种类型化妆品中PAEs的测定。     

Application of acetylacetone chelation solid-phase extraction to GFAAS measurements of trace amounts of beryllium in marine organisms.

Trace amounts of Be (0.046-2.59 ng) in a dried marine organism sample (10 mg) could be accurately determined by GFAAS after treating with microwave digestion (HNO3/H2O2) at 85 degrees C for 10 min and using acetylacetone as a chelating agent in the presence of an acetate buffer (pH 6.0). The method detection limit (MDL, 3sigma) for Be was found to be 4.6 ng g(-1); the calibration graph was linear up to 259 ng g(-1). Good recoveries (98.5-105.0%) were obtained for eight marine organism samples (including five fish, one lobster, one oyster, and one algae) with a relative standard deviation (RSD, n = 3) < 3.0%. The proposed method could be applied measurements of Be in various marine organisms.     

Analyses of pesticide residues in fruit-based baby food by liquid chromatography/electrospray ionization time-of-flight mass spectrometry

A liquid chromatography/electrospray ionization time-of-flight mass spectrometry (LC/ESI-TOFMS) method has been developed for the determination of 12 pesticides (namely, carbendazim, thiabendazole, imazalil, tridemorph, triadimefon, bitertanol, prochloraz, flutriafol, myclobutanil, iprodione, diphenylamine and procymidone) in fruit-based baby food (multi-fruit jars and juices intended for infant consumption). The developed method consists of a sample treatment step based on liquid-liquid extraction using acetonitrile, followed by a clean-up step based on dispersive solid-phase extraction (SPE) with a primary-secondary amine (PSA). Multi-fruit and apple juices were processed by a SPE procedure using Oasis HLB cartridges. Subsequent identification and quantitation was accomplished by LC/ESI-TOFMS analysis: the confirmation of the target pesticides was based on accurate mass measurements of selected ions (protonated molecules ([M+H]+) and fragment ions). Confirmation studies were accomplished at low concentration levels (10 microg kg-1) and accuracy errors lower than 2 ppm were obtained in most cases. Baby food extracts spiked at 10 microg kg-1 fortification level yielded average recoveries in the range 78-105% with relative standard deviations less than 10% for most of the analytes. Limits of detection (LODs) were between 0.1 and 4 microg kg-1 depending on the pesticide studied. Finally, the proposed method was applied to a total of 33 baby food samples from Spain and the United Kingdom. Although imazalil, thiabendazole and carbendazim were detected in a high number--over 60%- of baby food samples, none of the samples tested were found to be above the 0.01 mg kg-1 EU standard.     

-电感耦合等离子体质谱法测定硅锰冶炼渣中8种金属元素

实验采用HCl-HNO₃-HF-HClO₄混合酸为消解体系对样品进行前处理,加入1.0 mL盐酸羟胺溶液(100 g/L)溶解残渣,选择合适的同位素,以¹⁰³Rh为内标测定Cr、Co、Ni、Cu、Zn和Cd,以¹⁹³Ir为内标测定Tl和Pb,建立了电感耦合等离子体质谱(ICP-MS)法测定硅锰冶炼渣中8种重金属元素的方法。实验发现,样品前处理选择HCl∶HNO₃∶HF∶HClO₄=5∶5∶5∶1,并在复溶阶段加入1.0 mL盐酸羟胺溶液(100 g/L)可以完全消解样品,实验采用KED模式和干扰系数校正法消除质谱干扰,样品中待测元素的测定结果不受基体成分的干扰。通过绘制校准曲线及测定流程空白,各元素校准曲线的相关系数均大于0.9999,方法检出限为0.006~0.19 mg/kg,方法定量限为0.018~0.57 mg/kg。对硅锰渣实际样品进行测定,各元素的相对标准偏差(RSD,n=11)在0.83%~4.1%,加标回收率为94.7%~106%;经过人员比对实验,相对偏差为-4.54%~4.24%。测定结果稳定可靠,能满足硅锰冶炼渣中8种微量金属元素含量的分析检测要求。     

A simple supported liquid hollow fiber membrane microextraction for sample preparation of trihalomethanes in water samples

A simple and efficient liquid-phase microextraction (LPME) technique using a supported liquid hollow fiber membrane, in conjunction with gas chromatography-electron capture detector has been developed for extraction and determination of trihalomethanes (THMs) in water samples. THMs were extracted from water samples through an organic extracting solvent impregnated in the pores and filled inside the porous hollow fiber membrane. Our simple conditions were conducted at 35 degrees C with no stirring and no salt addition in order to minimize sample preparation steps. Parameters such as types of hollow fiber membranes, extracting solvents and extraction time were studied and optimized. The method exhibited enrichment factors ranged from 28- to 62-fold within 30 min extraction time. The linearity of the method ranged from 0.2 to 100 microg l(-1). The limits of detection were in the low microg l(-1) level, ranging between 0.01 and 0.2 microg l(-1). The recoveries of spiked THMs at 5 microg l(-1) in water were between 98 and 105% with relative standard deviations (RSDs) less than 4%. Furthermore, the method was applied for determination of THMs in drinking water and tap water samples was reported.     

Determination of some trace metals in waters by flame atomic absorption spectrometry after preconcentration on Amberlite XAD-16 resin with sodium tetraborate

A method was described for the determination of the elements Cr, Mn, Fe, Co, Ni, Cu, Cd, Pb, and Bi in waters by flame atomic absorption spectrometry (FAAS) after separation and preconcentration on Amberlite XAD-16 resin with sodium tetraborate using a chromatographic column. Parameters influencing the analytical performance, including pH and the volume of sample, amount of analyte and interfering effect of co-existing ions, were studied in detail. The recovery values were quantitative (> or = 95%), and the relative standard deviation (RSD) and detection limit (DL) varied in the range of 1.1-2.4% (n=10) and 0.002-0.177 microg m(-1) (3s, n=20), respectively. After being optimized, the proposed method was applied to the drinking water, waste water and artificial sea water samples. Recovery values of the elements investigated, were quantitative for tap water and synthetic sea water, except for Mn, Co and Ni (including also Cd for synthetic sea water). Recovery values of Cd, Pb, Cu and Co were found to be 95, 102, < or = 87, and < or = 83%, respectively, for the waste water samples.     

Cigarette filter as sorbent for on-line coupling of solid-phase extraction to high-performance liquid chromatography for determination of polycyclic aromatic hydrocarbons in water

An on-line solid-phase extraction (SPE) protocol using the cigarette filter as sorbent coupled with high-performance liquid chromatography (HPLC) was developed for simultaneous determination of trace naphthalene (NAPH), phenanthrene (PHEN), anthracene (ANT), fluoranthene (FLU), benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(a)pyrene (BaP), and benzo(ghi)perylene (BghiP) in water samples. To on-line interface solid-phase extraction to HPLC, a preconcentration column packed with the cigarette filter was used to replace a conventional sample loop on the injector valve of the HPLC for on-line solid-phase extraction. The sample solution was loaded and the analytes were then preconcentrated onto the preconcentration column. The collected analytes were subsequently eluted with a mobile phase of methanol-water (95:5). HPLC with a photodiode array detector was used for their separation and detection. The detection limits (S/N = 3) for preconcentrating 42 mL of sample solution ranged from 0.9 to 58.6 ng L(-1) at a sample throughput of 2 samples h(-1). The enhancement factors were in the range of 409-1710. The developed method was applied to the determination of trace NAPH, PHEN, ANT, FLU, BbF, BkF, BaP and BghiP in local river water samples. The recoveries of PAHs spiked in real water samples ranged from 87 to 115%. The precisions for nine replicate measurements of a standard mixture (NAPH: 4.0 microg L(-1), PHEN: 0.40 microg L(-1), ANT: 0.40 microg L(-1), FLU: 2.0 microg L(-1), BbF: 1.6 microg L(-1), BkF: 2.0 microg L(-1), BaP: 2.0 microg L(-1), BghiP: 1.7 microg L(-1)) were in the range of 1.2-5.1%.     

Determination of microcystins in fish by solvent extraction and liquid chromatography

A liquid chromatography electrospray mass spectrometry (LC/ESI/MS) method has been developed to identify and quantify microcystins in fish liver and intestine. Microcystins (MCs) were extracted from 500 mg sample with methanol-water (85:25, v/v) and the extracts concentrated to 250 microl. The parameters were optimized by a full factorial 2(3) design. Neither laborious pre-treatment nor clean up were necessary. MCs were separated using conventional C18 column and an acetonitrile-acidified water (pH 3) gradient. Negative samples (without MCs) were discriminated by liquid chromatography diode array detection (LC/DAD). The limits of detection (LOD) and the limits of quantification (LOQ) resulted equal for MC-RR, MC-YR, and MC-LR and were 0.1 and 0.5 microg g(-1), respectively. MCs recoveries at three levels in spiked samples (0.5-3.0 microg g(-1)) were > 92%, with relative standards deviations (RSDs) < 16% for liver samples and > 68% with RSDs < 18% for intestine samples. The proposed method was applied to determine MC-LR in exposed fish to evaluate the bioaccumulation risk. The results showed the transference of MC-LR from cyanobacterial cells to fish tissues.     

Simple and sensitive method for determination of glycoalkaloids in potato tubers by high-performance liquid chromatography with chemiluminescence detection

A novel, simple and sensitive high-performance liquid chromatographic method for the determination of the potato glycoalkaloids, alpha-solanine and alpha-chaconine, based on the chemiluminescent reaction of tris(2,2'-bipyridine)ruthenium(III) has been developed. The calibration graph was linear in the range of 5 ng/ml-10 microg/ml for both alpha-solanine and alpha-chaconine. The detection limits of alpha-solanine and alpha-chaconine were 1.2 and 1.3 ng/ml, respectively. This method was successfully applied to a potato tuber sample without cleanup, pre-concentration, and derivatization steps. The recoveries (mean +/- standard deviation, %) of alpha-solanine and alpha-chaconine spiked in tuber pith at 10 microg/g (n = 6) were 101.0 +/- 4.4% and 103.6 +/- 7.1%, respectively.     

Stability studies of carbamate pesticides and analysis by gas chromatography with flame ionization and nitrogen-phosphorus detection

As a result of thermal stability studies of carbamate pesticides, a method has been proposed for their direct determination by gas chromatography in the ranges 1-20 and 0.1-1 mg l(-1), using flame ionization and nitrogen-phosphorus detection, respectively. The method allows the determination of propham, propoxur, carbofuran, carbaryl, methiocarb, isopropoxyphenol and naphthol in powdered potato samples. The analytes were previously extracted with a light petroleum-dichloromethane (1:1, v/v) mixture and preconcentred by solid-phase extraction through a C8 cartridge. The recoveries obtained from spiked potato samples (n=4 replicates) at two concentration levels, 10 and 0.5 mg of pesticide per kg of sample, were in the ranges 72-115 and 50-73%, with relative standard deviations of 2-7 and 5-8%, respectively. The detection limits were 50-210 and 41-53 microg kg(-1) with flame ionization and nitrogen-phosphorus detection, respectively, and reaching the maximum residue levels, 0.05 mg kg(-1) for methiocarb and propoxur, set by the Real Decreto 280/1994 (based on the European directive).     

固相萃取-高效液相色谱法测定钙强化食品中的维生素D

以含有体积分数为20%的0.95 mol/L柠檬酸水溶液的二甲基亚砜作为维生素D的破壁溶液,利用Chromabond XTR固相萃取柱(14500 mg, 70 mL)对样品进行提取和净化,建立了测定钙强化食品中维生素D的固相萃取-高效液相色谱方法。方法的线性范围为0.1～100.0 μg/mL,线性相关系数为0.999。方法的定性检出限为0.01 μg/g,定量检出限为0.03 μg/g。低(0.1 μg/g)、中(0.5 μg/g)、高(1.0 μg/g)三个浓度水平的加标回收率分别为106.2%,99.5%和100.1%,相对标准偏差小于10%。