Electrochemistry and scanning electron microscopy of polyaniline/peroxidase-based biosensor

An amperometric biosensor was prepared by in situ deposition of horseradish peroxidase (HRP) enzyme on a polyaniline (PANI)-doped platinum disk electrode. The PANI film was electrochemically deposited on the electrode at 100 mV s⁻¹/Ag-AgCl. Cyclic voltammetric characterization of the PANI film in 1 M HCl showed two distinct redox peaks, which prove that the PANI film was electroactive and exhibited fast reversible electrochemistry. The surface concentration and film thickness of the adsorbed electroactive species was estimated to be 1.85×10⁻⁷ mol cm⁻² and approximately 16 nm, respectively. HRP was electrostatically immobilized onto the surface of the PANI film, and voltammetry was used to monitor the electrocatalytic reduction of hydrogen peroxide under diffusion-controlled conditions. Linear responses over the concentration range 2.5×10⁻⁴ to 5×10⁻³ M were observed. Spectroelectrochemistry was used to monitor the changes in UV-vis properties of HRP, before and after the catalysis of H₂O₂. The biosensor surface morphology was characterized by scanning electron microscopy (SEM) using PANI-doped screen-printed carbon electrodes (SPCEs) in the presence and absence of (i) peroxidase and (ii) peroxide. The SEM images showed clear modifications of the conducting film surface structure when doped with HRP, as well as the effect of hydrogen peroxide on the morphology of biosensor.     

Composite film of carbon nanotubes and chitosan for preparation of amperometric hydrogen peroxide biosensor

A new amperometric biosensor for hydrogen peroxide was developed based on cross-linking horseradish peroxidase (HRP) by glutaraldehyde with multiwall carbon nanotubes/chitosan (MWNTs/chitosan) composite film coated on a glassy carbon electrode. MWNTs were firstly dissolved in a chitosan solution. Then the morphology of MWNTs/chitosan composite film was characterized by field-emission scanning electron microscopy. The results showed that MWNTs were well soluble in chitosan and robust films could be formed on the surface. HRP was cross-linked by glutaraldehyde with MWNTs/chitosan film to prepare a hydrogen peroxide biosensor. The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for H₂O₂ in the absence of a mediator. The linear range of detection towards H₂O₂ (applied potential: −0.2 V) was from 1.67 × 10⁻⁵ to 7.40 × 10⁻⁴ M with correction coefficient of 0.998. The biosensor had good repeatability and stability for the determination of H₂O₂. There were no interferences from ascorbic acid, glucose, citrate acid and lactic acid.     

Development of hydrogen peroxide biosensor based on in situ covalent immobilization of horseradish peroxidase by one-pot polysaccharide-incorporated sol-gel process

A simple and reliable one-pot approach was established for the development of a novel hydrogen peroxide (H₂O₂) biosensor based on in situ covalent immobilization of horseradish peroxidase (HRP) into biocompatible material through polysaccharide-incorporated sol-gel process. Siloxane with epoxide ring and trimethoxy anchor groups was applied as the bifunctional cross-linker and the inorganic resource for organic-inorganic hybridization. The reactivity between amine groups and epoxy groups allowed the covalent incorporation of HRP and the functional biopolymer, chitosan (CS) into the inorganic polysiloxane network. Some experimental variables, such as mass ratio of siloxane to CS, pH of measuring solution and applied potential for detection were optimized. HRP covalently immobilized in the hybrid matrix possessed high electrocatalytic activity to H₂O₂ and provided a fast amperometric response. The linear response of the as-prepared biosensor for the determination of H₂O₂ ranged from 2.0 × 10⁻⁷ to 4.6 × 10⁻⁵ mol l⁻¹ with a detection limit of 8.1 × 10⁻⁸ mol l⁻¹. The apparent Michaelis-Menten constant was determined to be 45.18 μmol l⁻¹. Performance of the biosensor was also evaluated with respect to possible interferences. The fabricated biosensor exhibited high reproducibility and storage stability. The ease of the one-pot covalent immobilization and the biocompatible hybrid matrix serve as a versatile platform for enzyme immobilization and biosensor fabricating.     

Mesoporous silica hollow sphere (MSHS) for the bioelectrochemistry of horseradish peroxidase

In this work, novel mesoporous silica hollow spheres (MSHS) were chosen as an immobilization matrix, to construct a mediator-free third-generation HRP biosensor. UV-vis spectroscopy revealed that horseradish peroxidase (HRP) entrapped in MSHS could retain its native structure. FTIR spectroscopy and nitrogen adsorption-desorption isotherms indicated that HRP are intercalated into the mesopores. The direct electron transfer of HRP entrapped in MSHS was observed. A pair of stable and well-defined redox peaks of HRP with a formal potential of about −0.150 V (vs. Ag/AgCl) in 0.1 M pH 7.0 phosphate-buffered solution (PBS) were obtained. The biosensor exhibited a fast amperometric response to H₂O₂ with a linear range of 3.9 × 10⁻⁶ to 1.4 × 10⁻⁴ M (R = 0.997, N = 20). The detection limit was 1.2 × 10⁻⁶ M based S/N = 3.     

Amperometric biosensor for hydrogen peroxide based on coimmobilized horseradish peroxidase and methylene green in ormosils matrix with multiwalled carbon nanotubes

A novel amperometric biosensor for the analytical determination of hydrogen peroxide was developed. The fabrication of the biosensor was based on the coimmobilization of horseradish peroxidase (HRP), methylene green (MG) and multiwalled carbon nanotubes within ormosils; 3-aminopropyltrimethoxysilane (APTMOS), 2-(3,4-epoxycyclohexyl)ethyltrimethoxysilane (ETMOS) and phenyltrimethoxysilane (PHTMOS). APTMOS determined the hydrophilicity/hydrophobicity of the ormosils and PHTMOS and ETMOS increased the physical and mechanical strength of the ormosil matrix. The ormosil modified electrodes were characterized with SEM, UV-vis spectroscopy and electrochemical methods. Cyclic voltammetry and amperometric measurements demonstrated the MG coimmobilized with HRP in this way, displayed good stability and could efficiently shuttle electrons between immobilized enzyme and electrode, and MWCNTs facilitated the electrocatalytic reduction of H₂O₂ at reduced over potential. The Micheaelis constant of the immobilized HRP was 1.8 mM, indicating a high affinity of the HRP to H₂O₂ without loss of enzymatic activity in ormosil matrix. The prepared biosensor had a fast response of H₂O₂, less than 10 s, and excellent linear range of concentration from 5 × 10⁻⁷ to 2 × 10⁻⁵ M with the detection limit of 0.5 μM (S/N = 3) under the optimum conditions. At the same time, the influence of solution pH, effect of enzyme amount, steady-state applied potential and temperature on the biosensor were investigated. The enzyme electrode retained about 90% of its initial activity after 30 days of storage in a dry state at 4 °C. The preparation of the developed biosensor was convenient and showed high sensitivity with good stability.     

Integrated multienzyme electrochemical biosensors for the determination of glycerol in wines

The construction and performance of integrated amperometric biosensors for the determination of glycerol are reported. Two different biosensor configurations have been evaluated: one based on the glycerol dehydrogenase/diaphorase (GDH/DP) bienzyme system, and another using glycerol kinase/glycerol-3-phosphate oxidase/peroxidase (GK/GPOx/HRP). Both enzyme systems were immobilized together with the mediator tetrathiafulvalene (TTF) on a 3-mercaptopropionic acid (MPA) self-assembled monolayer (SAM)-modified gold electrode by using a dialysis membrane. The electrochemical oxidation of TTF at +150 mV (vs. Ag/AgCl), and the reduction of TTF⁺ at 0 mV were used for the monitoring of the enzyme reactions for the bienzyme and trienzyme configurations, respectively. Experimental variables concerning both the biosensors composition and the working conditions were optimized for each configuration. A good repeatability of the measurements with no need of cleaning or pretreatment of the biosensors was obtained in both cases. After 51 days of use, the GDH/DP biosensor still exhibited 87% of the original sensitivity, while the GK/GPOx/HRP biosensor yielded a 46% of the original response after 8 days. Calibration graphs for glycerol with linear ranges of 1.0 × 10⁻⁶ to 2.0 × 10⁻⁵ or 1.0 × 10⁻⁶ to 1.0 × 10⁻⁵ M glycerol and sensitivities of 1214 ± 21 or 1460 ± 34 μA M⁻¹ were obtained with GDH/DP and GK/GPOx/HRP biosensors, respectively. The calculated detection limits were 4.0 × 10⁻⁷ and 3.1 × 10⁻⁷ M, respectively. The biosensors exhibited a great sensitivity with no significant interferences in the analysis of wines. The biosensors were applied to the determination of glycerol in 12 different wines and the results advantageously compared with those provided by a commercial enzyme kit.     

Integrated multienzyme electrochemical biosensors for monitoring malolactic fermentation in wines

Integrated amperometric biosensors for the determination of l-malic and l-lactic acids were developed by coimmobilization of the enzymes l-malate dehydrogenase (MDH) and diaphorase (DP), or l-lactate oxidase (LOX) and horseradish peroxidase (HRP), respectively, together with the redox mediator tetrathiafulvalene (TTF), on a 3-mercaptopropionic acid (MPA) self-assembled monolayer (SAM)-modified gold electrode by using a dialysis membrane. The electrochemical oxidation of TTF at +100 mV (vs. Ag/AgCl), and the reduction of TTF⁺ at −50 mV were used for the monitoring of the enzyme reactions involved in l-malic and l-lactic acid determinations, respectively. Experimental variables concerning the biosensors composition and the detection conditions were optimized for each biosensor. Good relative standard deviation values were obtained in both cases for the measurements carried out with the same biosensor, with no need of cleaning or pretreatment of the bioelectrodes surface, and with different biosensors constructed in the same manner. After 7 days of continuous use, the MDH/DP biosensor still exhibited 90% of the original sensitivity, while the LOX/HRP biosensor yielded a 91% of the original response after 5 days. Calibration graphs for l-malic and l-lactic were obtained with linear ranges of 5.2 × 10⁻⁷ to 2.0 × 10⁻⁵ and 4.2 × 10⁻⁷ to 2.0 × 10⁻⁵ M, respectively. The calculated detection limits were 5.2 × 10⁻⁷ and 4.2 × 10⁻⁷ M, respectively. The biosensors exhibited a high selectivity with no significant interferences. They were applied to monitor malolactic fermentation (MLF) induced by inoculation of Lactobacillus plantarum CECT 748^T into a synthetic wine. Samples collected during MLF were assayed for l-malic and l-lactic acids, and the results obtained with the biosensors exhibited a very good correlation when plotted against those obtained by using commercial enzymatic kits.     

Bilayer lipid membrane biosensor with enhanced stability for amperometric determination of hydrogen peroxide

In this paper, a polydopamine (PDA) film is electropolymerized on the surface of bilayer lipid membrane (BLM) which is immobilized with horseradish peroxidase (HRP). The coverage of the PDA film on HRP/BLM electrode is monitored by electrochemical impedance spectroscopy (EIS). The electrocatalytic reduction of H₂O₂ at the PDA/HRP/BLM electrode is studied by means of cyclic voltammetry (CV). The biosensor has a fast response to H₂O₂ of less than 5 s and an excellent linear relationship is obtained in the concentration range from 2.5 × 10⁻⁷ to 3.1 × 10⁻³ mol L⁻¹, with a detection limit of 1.0 × 10⁻⁷ mol L⁻¹ (S/N = 3). The response current of BLM/HRP/PDA biosensor retains 84% of its original response after being stored in 0.1 mol L⁻¹ pH 7.0 PBS at 4 °C for 3 weeks. The selectivity, repeatability, and storage stability of PDA/HRP/BLM biosensor are greatly enhanced by the coverage of polydopamine film on BLM.     

One-step construction of reagentless biosensor based on chitosan-carbon nanotubes-nile blue-horseradish peroxidase biocomposite formed by electrodeposition

A simple and controllable electrodeposition approach was established for one-step construction of novel reagentless biosensors by in situ formation of chitosan-carbon nanotubes-nile blue-horseradish peroxidase (CS-CNTs-NB-HRP) biocomposite film on electrode surface. The mediator effect of NB, conducting performance of CNTs and the biocompatible microenvironment of CS were combined by such one-step non-manual process. NB could interact with CNTs and resulted in good dispersion of CNTs-NB nanocomposites in aqueous solution. Cyclic voltammetry measurements demonstrated that electrons were efficiently shuttled between HRP and the electrode mediated by NB. The developed reagentless biosensor exhibited a fast amperometric response for the determination of H₂O₂ and 95% of the steady-state current was obtained within 2 s. The linear response of the reagentless biosensor for the determination of H₂O₂ ranged from 1.0 × 10⁻⁶ to 2.4 × 10⁻⁴ mol l⁻¹ with a detection limit of 1.2 × 10⁻⁷ mol l⁻¹. The biosensor exhibited high reproducibility and long-time storage stability. The as-prepared biosensor also showed effective anti-interference capability. The ease of the one-step non-manual technique and the promising feature of the biocomposite could serve as a versatile platform for fabricating electrochemical biosensors.     

Mn(II)-sodium dodecyl sulphate complex mimic enzyme-catalyzed fluorescence quenching of Pyronine B by hydrogen peroxide

Mn(II)-sodium dodecyl sulphate complex (Mn(II)-SDS) is used to mimic the active group of peroxidase. The catalytic characteristic of this mimic enzyme catalyst in the oxidation reaction of fluorescence substrate, tetraethyldiaminoxanthyl chloride (Pyronine B (PB)), with hydrogen peroxide has been studied. The experimental results show that Mn(II)-SDS complex has similar catalytic activity that of peroxidase. The steady-state catalytic rate depends upon mimic enzyme and substrate concentrations, and the Michaelis-Menten parameters K_m, V_max and K_cat are 7.6×10⁻⁶ M, 7.9×10⁻⁷ M s⁻¹ and 7.9 s⁻¹, respectively. The catalytic activity of Mn(II)-SDS complex is compared with those of HRP and Hemin. Though the catalytic activity of Mn(II)-SDS complex is 15.9% of that of HRP, it can catalyze the oxidation reaction of PB with hydrogen peroxide lead to fluorescence quenching of PB. Under optimum conditions, linear relationship between fluorescence quenching F₀/F and concentration of H₂O₂ is in the range of (0.0-3.6) × 10⁻⁷ M. The detection limit is determined to be 3.0×10⁻⁹ M. By coupling this mimic catalytic reaction with the catalytic reaction of glucose oxidase (GOD), glucose can be detected. Linear relationship between F₀/F and concentration of glucose is in the range of (0.0-1.4) × 10⁻⁷ M. The detection limit is determined to be 4.2×10⁻⁹ M. This method is applied to the determination of glucose in human serum and the results are in good agreement with the phenol-4-aminoantipyrine (4-AAP).     

Chemically glycosylation improves the stability of an amperometric horseradish peroxidase biosensor

We constructed a biosensor by electrodeposition of gold nano-particles (AuNPs) on glassy carbon (GC) and subsequent formation of a 4-mercaptobenzoic acid self-assembled monolayer (SAM). The enzyme horseradish peroxidase (HRP) was then covalently immobilized onto the SAM. Two forms of HRP were employed: non-modified and chemically glycosylated with lactose. Circular dichroism (CD) spectra showed that chemical glycosylation did neither change the tertiary structure of HRP nor the heme environment. The highest sensitivity of the biosensor to hydroquinone was obtained for the biosensor with HRP-lactose (414 nA μM⁻¹) compared to 378 nA μM⁻¹ for the one employing non-modified HRP. The chemically glycosylated form of the enzyme catalyzed the reduction of hydroquinone more rapidly than the native form of the enzyme. The sensor employing lactose-modified HRP also had a lower limit of detection (74 μM) than the HRP biosensor (83 μM). However, most importantly, chemically glycosylation improved the long-term stability of the biosensor, which retained 60% of its activity over a four-month storage period compared to only 10% for HRP. These results highlight improvements by an innovative stabilization method when compared to previously reported enzyme-based biosensors.     

Bienzymatic amperometric biosensor for glucose based on polypyrrole/ceramic carbon as electrode material

A novel amperometric biosensor utilizing two enzymes, glucose oxidase (GOD) and horseradish peroxidase (HRP), was developed for the cathodic detection of glucose. The glucose biosensor was constructed by electrochemical formation of a polypyrrole (PPy) membrane in the presence of GOD on the surface of a HRP-modified sol-gel derived-mediated ceramic carbon electrode. Ferrocenecarboxylic acid (FCA) was used as mediator to transfer electron between enzyme and electrode. In the hetero-bilayer configuration of electrode, all enzymes were well immobilized in electrode matrices and showed favorable enzymatic activities. The amperometric detection of glucose was carried out at +0.16 V (versus saturated calomel reference electrode (SCE)) in 0.1 M phosphate buffer solution (pH 6.9) with a linear response range between 8.0×10⁻⁵ and 1.3×10⁻³ M glucose. The biosensor showed a good suppression of interference in the amperometric detection.     

Amperometric biosensor for hydrogen peroxide based on hemoglobin entrapped in titania sol-gel film

Hemoglobin (Hb) was entrapped in a titania sol-gel matrix and used as a mimetic peroxidase to construct a novel amperometric biosensor for hydrogen peroxide. The Hb entrapped titania sol-gel film was obtained with a vapor deposition method, which simplified the traditional sol-gel process for protein immobilization. The morphologies of both titania sol-gel and the Hb films were characterized using scanning electron microscopy (SEM) and proved to be chemically clean, porous, homogeneous. This matrix provided a biocompatible microenvironment for retaining the native structure and activity of the entrapped Hb and a very low mass transport barrier to the substrates. H₂O₂ could be reduced by the catalysis of the entrapped hemoglobin at −300 mV without any mediator. The reagentless H₂O₂ sensor exhibited a fast response (less than 5 s) and sensitivity as high as 1.29 mA mM⁻¹ cm⁻². The linear range for H₂O₂ determination was from 5.0×10⁻⁷ to 5.4×10⁻⁵ M with a detection limit of 1.2×10⁻⁷ M. The apparent Michaelis-Menten constant of the encapsulated hemoglobin was calculated to be 0.18±0.02 mM. The stability of the biosensor was also evaluated.     

Uric acid determination using uricase and the autotransducer molecular absorption properties of peroxidase

Uric acid (UA) is determined using the UV-vis molecular absorption properties of peroxidase (HRP). The method as a whole involves UA oxidation in the presence of uricase (UOx), giving H₂O_2. The H₂O₂ then reacts with HRP forming the compound I species which returns to its initial form by reaction with UA and intramolecular reduction. The molecular absorption changes of HRP at 420 nm during the reaction enable the UA to be determined. A mathematical model relating the analytical signal to UA, UOx and HRP has been developed and experimentally validated. The possibility of carrying out both enzymatic reactions sequentially or simultaneously is discussed, the latter option producing better analytical performances. The method permits UA determination in the range 1.5 × 10⁻⁶-4.0 × 10⁻⁵ M, with an R.S.D. of about 3% (n = 5, 1.5 × 10⁻⁶ M UA). It has been applied to analyte determination in synthetic serum samples.     

FIA-near-infrared spectrofluorimetric trace determination of hydrogen peroxide using tricarchlorobocyanine dye (Cy.7.Cl) and horseradish peroxidase (HRP)

A new kind of near-infrared fluorescence agent, tricarbochlorocyanine dye (Cy.7.Cl), had been synthesized in house and used for near-infrared spectrofluorimetric determination of hydrogen peroxide (H₂O₂) by flow injection analysis (FIA) for the first time. The oxidation reaction of Cy.7.Cl with H₂O₂ occurred under the catalysis of horseradish peroxidase (HRP) and it was studied in detail. The possible reaction mechanism was discussed. Under optimal experimental conditions, fluorescence from Cy.7.Cl displayed excitation and emission maxima (ex/em) at 780 and 800 nm, respectively. The two linear working ranges were 1.86 × 10⁻⁷ to 4.11 × 10⁻⁷ mol L⁻¹ and 4.11 × 10⁻⁷ to 7.19 × 10⁻⁶ mol L⁻¹, respectively. The detection limit was 5.58 × 10⁻⁸ mol L⁻¹ of H₂O₂. The effect of interferences was studied. The proposed method was successfully applied to the determination of hydrogen peroxide in rainwater, serum and plant samples.     

Quantification of biogenic amines by microchip electrophoresis with chemiluminescence detection

A highly sensitive microchip electrophoresis (MCE) method with chemiluminescence (CL) detection was developed for the determination of biogenic amines including agmatine (Agm), epinephrine (E), dopamine (DA), tyramine, and histamine in human urine samples. To achieve a high assay sensitivity, the targeted analytes were pre-column labeled by a CL tagging reagent, N-(4-aminobutyl)-N-ethylisoluminol (ABEI). ABEI-tagged biogenic amines after MCE separation reacted with hydrogen peroxide in the presence of horseradish peroxidase (HRP), producing CL emission. Since no CL reagent was added to the running buffer, the background of the CL detection was extremely low, resulting in a significant improvement in detection sensitivity. Detection limits (S/N = 3) were in the range from 5.9 × 10⁻⁸ to 7.7 × 10⁻⁸ M for the biogenic amines tested, which were at least 10 times lower than those of the MCE–CL methods previously reported. Separation of a urine sample on a 7 cm glass/poly(dimethylsiloxane) (PDMS) microchip channel was completed within 3 min. Analysis of human urine samples found that the levels of Agm, E and DA were in the ranges of 2.61 × 10⁻⁷ to 4.30 × 10⁻⁷ M, 0.81 × 10⁻⁷ to 1.12 × 10⁻⁷ M, and 8.76 × 10⁻⁷ to 11.21 × 10⁻⁷ M (n = 4), respectively.     

Preparation and characterization of Prussian blue nanowire array and bioapplication for glucose biosensing

Prussian blue nanowire array (PBNWA) was prepared via electrochemical deposition with polycarbonate membrane template for effective modification of glassy carbon electrode. The PBNWA electrode thus obtained was demonstrated to have high-catalytic activity for the electrochemical reduction of hydrogen peroxide in neutral media. This enabled the PBNWA electrode to show rapid response to H₂O₂ at a low potential of −0.1 V over a wide range of concentrations from 1 × 10⁻⁷ M to 5 × 10⁻² M with a high sensitivity of 183 μA mM⁻¹ cm⁻². Such a low-working potential also substantially improved the selectivity of the PBNWA electrode against most electroactive species such as ascorbic acid and uric acid in physiological media. A detection limit of 5 × 10⁻⁸ M was obtained using the PBNWA electrode for H₂O₂, which compared favorably with most electroanalysis procedures for H₂O₂. A biosensor toward glucose was then constructed with the PBNWA electrode as the basic electrode by crosslinking glucose oxidase (GOx). The glucose biosensor allowed rapid, selective and sensitive determination of glucose at −0.1 V. The amperometric response exhibited a linear correlation to glucose concentration through an expanded range from 2 × 10⁻⁶ M to 1 × 10⁻² M, and the response time and detection limit were determined to be 3 s and 1 μM, respectively.     

Characterization of graphite electrodes modified with laccase from Trametes versicolor and their use for bioelectrochemical monitoring of phenolic compounds in flow injection analysis

Spectrographic graphite electrodes were modified through adsorption with laccase from Trametes versicolor. The laccase-modified graphite electrode was used as the working electrode in an amperometric flow-through cell for monitoring phenolic compounds in a single line flow injection system. The experimental conditions for bioelectrochemical determination of catechol were studied and optimized. The relative standard deviation of the biosensor for catechol (10 μM, n=12) was 1.0% and the reproducibility for six laccase-modified graphite electrodes, prepared and used different days was about 11%. The optimal conditions for the biosensor operation were: 0.1 M citrate buffer solution ( at pH 5.0), flow rate of 0.51 ml min⁻¹ and a working potential of −50 mV versus Ag|AgCl. At these conditions the responses of the biosensor for various phenolic compounds were recorded and the sensor characteristics were calculated and compared with those known for biosensors based on laccase from Coriolus hirsutus, cellobiose dehydrogenase (CDH) from Phanerochaete chrysosporium and horseradish peroxidase (HRP).     

Electrochemiluminescent disposable cholesterol biosensor based on avidin–biotin assembling with the electroformed luminescent conducting polymer poly(luminol-biotinylated pyrrole)

An electrochemiluminescent cholesterol disposable biosensor has been prepared by the formation of assembled layers on gold screen-printed cells. The detection layer is based on the electro-formation of new luminol copolymers with different synthesized biotinylated pyrroles prepared by click-chemistry, offering a new transduction layer with new electroluminescent properties on biosensors. The electrochemiluminescence (ECL) luminol copolymers are electroformed by cyclic voltammetry (five cycles) at pH 7.0 uses a10⁻³ M biotinylated pyrrole–luminol ratio of 1:10 in PBS buffer. With respect to the recognition layer, cholesterol oxidase was biotinylated by incubation with biotin vinyl sulfone, and immobilized on the copolymer by avidin–biotin interaction. The analytical signal of the biosensor is the ECL enzymatic initial rate working in chronoamperometric mode at 0.5 V excitation potential with 10 s between pulses at pH 9.5. The disposable device offers a cholesterol linear range from 1.5 × 10⁻⁵ M to 8.0 × 10⁻⁴ M with a limit of detection of 1.47 × 10⁻⁵ M and accuracy of 7.9% for 9.0 × 10⁻⁵ M and 14.1% for 2.0 × 10⁻⁴ M, (n = 5). Satisfactory results were obtained for cholesterol determination in serum samples compared to a reference procedure.     

A novel amperometric biosensor for the detection of nitrophenol

We report on a novel amperometric biosensor for detecting phenolic compounds based on the co-immobilization of horseradish-peroxidase (HRP) and methylene blue (MB) with chitosan on Au-modified TiO₂ nanotube arrays. The titania nanotube arrays were directly grown on a Ti substrate using anodic oxidation first; a gold thin film was then coated onto the TiO₂ nanotubes by an argon plasma technique. The morphology and composition of the fabricated Au-modified TiO₂ nanotube arrays were characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Cyclic voltammetry and amperometry were used to study the proposed electrochemical biosensor. The effect of pH, applied electrode potential and the concentration of H₂O₂ on the sensitivity of the biosensor have been systemically investigated. The performance of the proposed biosensor was tested using seven different phenolic compounds, showing very high sensitivity; in particular, the linearity of the biosensor for the detection of 3-nitrophenol was observed from 3 × 10⁻⁷ to 1.2 × 10⁻⁴ M with a detection limit of 9 × 10⁻⁸ M (based on the S/N = 3).