Quantification of 13 priority polycyclic aromatic hydrocarbons in human urine by headspace solid-phase microextraction gas chromatography-isotope dilution mass spectrometry

Polycyclic aromatic hydrocarbons (PAHs) are common environmental pollutants in both living and working environments. The aim of this study was the development of a headspace solid-phase microextraction gas chromatography-isotope dilution mass spectrometry (HS-SPME/GC-IDMS) method for the simultaneous quantification of 13 PAHs in urine samples. Different parameters affecting PAHs extraction by HS-SPME were considered and optimized: type/thickness of fiber coatings, extraction temperature/time, desorption temperature/time, ionic strength and sample agitation. The stability of spiked PAHs solutions and of real urine samples stored up to 90 days in containers of different materials was evaluated. In the optimized method, analytes were absorbed for 60 min at 80 °C in the sample headspace with a 100 μm polydimethylsiloxane fiber. The method is very specific, with linear range from the limit of quantification to 8.67 × 10³ ng L⁻¹, a within-run precision of <20% and a between-run precision of <20% for 2-, 3- and 4-ring compounds and of <30% for 5-ring compounds, trueness within 20% of the spiked concentration, and limit of quantification in the 2.28-2.28 × 10¹ ng L⁻¹ range. An application of the proposed method using 15 urine samples from subjects exposed to PAHs at different environmental levels is shown.     

Ultrasonication extraction and gel permeation chromatography clean-up for the determination of polycyclic aromatic hydrocarbons in edible oil by an isotope dilution gas chromatography–mass spectrometry

An analytical method for the determination of US EPA priority pollutant 16 polycyclic aromatic hydrocarbons (PAHs) in edible oil was developed by an isotope dilution gas chromatography–mass spectrometry (GC–MS). Extraction was performed with ultrasonication mode using acetonitrile as solvent, and subsequent clean-up was applied using narrow gel permeation chromatographic column. Three deuterated PAHs surrogate standards were used as internal standards for quantification and analytical quality control. The limits of quantification (LOQs) were globally below 0.5 ng/g, the recoveries were in the range of 81–96%, and the relative standard deviations (RSDs) were lower than 20%. Further trueness assessment of the method was also verified through participation in international cocoa butter proficiency test (T0638) organised by the FAPAS with excellent results in 2008. The results obtained with the described method were satisfying (z ≤ 2). The method has been applied to determine PAH in real edible oil samples.     

Solid-phase microextraction—Gas chromatography to determine volatile organic sulfur compounds in the air at sewage treatment plants

Solid-phase microextraction (SPME) was applied to the determination of 7 volatile organic sulfur compounds (VOSCs), which were analysed by gas chromatography-mass spectrometry. The compounds studied were ethyl mercaptan (CH₃CH₂SH), dimethyl sulfide ((CH₃)₂S), carbon disulfide (CS₂), propyl mercaptan (C₃H₈S), butyl mercaptan (C₄H₁₀S), dimethyl disulfide ((CH₃)₂S₂) and 1-pentanethiol (C₅H₁₂S). Temperature and time conditions of SPME extraction were optimised and the method was validated, with good linearity in a calibration range between 0.1 and 1000 μg m⁻³. Method detection limits ranged between 0.01 and 0.08 μg m⁻³ and method quantification limits were between 0.10 and 0.25 μg m⁻³, allowing real samples taken from several different areas of a sewage treatment plant to be analysed. Repeatability of the method between samples went from 5.6% for pentanethiol up to 14.2% for carbon disulfide, and concentrations of total target compounds were found between 18 and 529 μg m⁻³, depending on the sampling site.     

Air pollution from traffic emissions in Oporto, Portugal: Health and environmental implications

Air pollution represents a serious risk not only to environment and human health, but also to historical heritage. In this study, air pollution of the Oporto Metropolitan Area and its main impacts were characterized. The results showed that levels of CO, PM₁₀ and SO₂ have been continuously decreasing in the respective metropolitan area while levels of NO_x and NO₂ have not changed significantly. Traffic emissions were the main source of the determined polycyclic aromatic hydrocarbons (PAHs; 16 PAHs considered by U.S. EPA as priority pollutants, dibenzo[a,l]pyrene and benzo[j]fluoranthene) in air of the respective metropolitan area. The mean concentration of 18 PAHs in air was 69.9 ± 39.7 ng m⁻³ with 3-4 rings PAHs accounting for 75% of the total Σ_PAHs. The health risk analysis of PAHs in air showed that the estimated values of lifetime lung cancer risks considerably exceeded the health-based guideline level. Analytical results also confirm that historical monuments in urban areas act as passive repositories for air pollutants present in the surrounding atmosphere. FTIR and EDX analyses showed that gypsum was the most important constituent of black crusts of the characterized historical monument Monastery of Serra do Pilar classified as “UNESCO World Cultural Heritage”. In black crusts, 4-6 rings compounds accounted approximately for 85% of Σ_PAHs. The diagnostic ratios confirmed that traffic emissions were the major source of PAHs in black crusts; PAH composition profiles were very similar for crusts and PM₁₀ and PM_2.5.     

Response of halogenated compounds in ion mobility spectrometry depending on their structural features

Ion mobility spectrometry (IMS) with handheld and transportable devices permits the sensitive detection of chlorinated compounds which are important in environmental monitoring. The ion mobility spectra in negative measuring modus mostly show one product ion peak [(H₂O)_nCl⁻] due to dissociative electron attachments. In this paper, we investigated relevant chlorinated compounds (R-Cl) where R represents allyl-, benzyl-, phenyl-, alkyl- and vinyl-groups. These groups cause differences in the R-Cl bond strength and differences in the cleavage of chlorine can therefore be expected. All chlorinated substances investigated provide the same product ion peak at 2.75 cm² Vs⁻¹ independent on the different C-Cl bond strength. However, distinct influences of structural features on the peak intensities of the (H₂O)_nCl⁻ product ion peak were established. Generally, increasing sensitivities were obtained in the order chlorobenzenes < vinyl- < allyl- < alkyl compounds < benzylchlorides. Sensitivities and limits of detection (LODs) of aromatic compounds depend on the nature and position of second substituent. Electron-withdrawing substituents (chlorine, fluorine, nitrile) enhance sensitivity while electron-repelling substituents decrease it. A dependence of sensitivity on the chain length or ring size can be observed for alkyl compounds. Additional influences of intramolecular interactions on the sensitivity were found for di-halogenated compounds. Therefore, the quantification of negative product ion peaks of chlorinated compounds requires a consideration of structural features of analytes.     

Quantitative analysis of polycyclic aromatic hydrocarbons using high-performance liquid chromatography-photodiode array-high-resolution mass spectrometric detection platform coupled to electrospray and atmospheric pressure photoionization sources

Polycyclic aromatic hydrocarbons (PAHs) are common pollutants present in atmospheric aerosols and other environmental mixtures. They are of particular air quality and human health concerns as many of them are carcinogenic toxins. They also affect absorption of solar radiation by aerosols, therefore contributing to the radiative forcing of climate. For environmental chemistry studies, it is advantageous to quantify PAH components using the same analytical technics that are commonly applied to characterize a broad range of polar analytes present in the same environmental mixtures. Liquid chromatography coupled with photodiode array and high-resolution mass spectrometric detection (LC-PDA-HRMS) is a method of choice for comprehensive characterization of chemical composition and quantification of light absorption properties of individual organic compounds present in the environmental samples. However, quantification of non-polar PAHs by this method is poorly established because of their imperfect ionization in electrospray ionization (ESI) technique. This tutorial article provides a comprehensive evaluation of the quantitative analysis of 16 priority pollutant PAHs in a standard reference material using the LC–MS platform coupled with the ESI source. Results are further corroborated by the quantitation experiments using an atmospheric pressure photoionization (APPI) method, which is more sensitive for the PAH detection. The basic concepts and step-by-step practical guidance for the PAHs quantitative characterization are offered based on the systematic experiments, which include (1) Evaluation effects of different acidification levels by formic acid on the (+)ESI-MS detection of PAHs. (2) Comparison of detection limits in ESI+ versus APPI+ experiments. (3) Investigation of the PAH fragmentation patterns in MS² experiments at different collision energies. (4) Calculation of wavelength dependent mass absorption coefficient (MAC_λ) of the standard mixture and its individual PAHs using LC-PDA data. (5) Assessment of the minimal injected mass required for accurate quantification of MAC_λ of the standard mixture and of a multi-component environmental sample.     

Comparison of two extraction methods for evaluation of volatile constituents patterns in commercial whiskeys Elucidation of the main odour-active compounds

An analytical procedure based on manual dynamic headspace solid-phase microextraction (HS-SPME) method and the conventional extraction method by liquid-liquid extraction (LLE), were compared for their effectiveness in the extraction and quantification of volatile compounds from commercial whiskey samples. Seven extraction solvents covering a wide range of polarities and two SPME fibres coatings, has been evaluated. The highest amounts extracted, were achieved using dichloromethane (CH₂Cl₂) by LLE method (LLECH₂Cl₂) and using a CAR/PDMS fibre (SPME_CAR/PDMS) in HS-SPME. Each method was used to determine the responses of 25 analytes from whiskeys and calibration standards, in order to provide sensitivity comparisons between the two methods. Calibration curves were established in a synthetic whiskey and linear correlation coefficient (r) were greater than 0.9929 for LLECH₂Cl₂ and 0.9935 for SPME_CAR/PDMS, for all target compounds. Recoveries greater than 80% were achieved. For most compounds, precision (expressed by relative standard deviation, R.S.D.) are very good, with R.S.D. values lower than 14.78% for HS-SPME method and than 19.42% for LLE method. The detection limits ranged from 0.13 to 19.03 μg L⁻¹ for SPME procedure and from 0.50 to 12.48 μg L⁻¹ for LLE.A tentative study to estimate the contribution of a specific compound to the aroma of a whiskey, on the basis of their odour activity values (OAV) was made. Ethyl octanoate followed by isoamyl acetate and isobutyl alcohol, were found the most potent odour-active compounds.     

Comparison of ultrasonic and pressurized liquid extraction for the analysis of polycyclic aromatic compounds in soil samples by gas chromatography coupled to tandem mass spectrometry

A pressurized liquid extraction (PLE) method has been optimized for the determination of polycyclic aromatic hydrocarbons (PAHs) in soil samples and it was compared with ultrasonic extraction. The extraction step was followed by gas chromatography-triple quadrupole mass spectrometry (GC-QqQ-MS/MS) analysis. Parameters such as type of solvent, extraction time, extraction temperature and number of extractions were optimized. There were no significant differences among the two extraction methods although better extraction efficiencies were obtained when PLE was used, minimizing extraction time and solvent consumption. PLE procedure was validated, obtaining limits of detection (LODs) ranging from 0.02 to 0.75 μg kg⁻¹ and limits of quantification (LOQs) ranging from 0.07 to 2.50 μg kg⁻¹ for the selected PAHs. Recoveries were in the range of 59-110%, except for naphthalene, which was the most volatile PAH. Finally, the method was applied to real soil samples from Southeast of Spain. PAHs concentrations were low, and phenanthrene, pyrene, fluorene, benzo[a]pyrene and chrysene were the most frequently detected analytes in the samples.     

Highly sensitive and selective fluorescence optosensor to detect and quantify benzo[a]pyrene in water samples

We describe here a method for detecting and quantifying the highly carcinogenic polycyclic aromatic hydrocarbon (PAH) benzo[a]pyrene (BaP) in water, based on a flow-trough optical sensor. The technique is fast (response time of 40 s) and simple and at the same time meets the standards of sensitivity and selectivity required by the European Guidelines on Water for Human Consumption. The optosensor is based on the on-line immobilization of BaP on a non-ionic resin (Amberlite XAD-4) solid support in a continuous-flow system. BaP was analyzed in a 15 mM H₂PO₄⁻/HPO₄²⁻ buffer solution with 25% (v/v) 1,4-dioxane at pH 7. Fluorescence intensity was measured at λ_ex/em=392/406 nm. The experimental conditions (reagent phase, pH, type and concentration of buffer solution and organic solvent) and flow-injection values (flow rate and injection volume) were carefully controlled. Under these conditions the optosensor was sensitive to a linear concentration range of between 3.0 and 250.0 ng l⁻¹ with a detection limit of 3.0 ng l⁻¹ and a standard deviation of 1.5% at 150 ng l⁻¹. The optosensor was applied to the quantification of BaP in drinking and waste water samples (95-105% recovery) in presence of the other 15 EPA PAHs at 1000 ng l⁻¹ concentration level. The influence of other fluorescent polycyclic aromatic hydrocarbons and potential interference from ions usually present in water was also evaluated.     

Pressurised membrane-assisted liquid extraction of UV filters from sludge

A method for the determination of 11 UV-filter compounds in sludge has been developed and evaluated. The procedure includes the use of non-porous polymeric membranes in combination with pressurised liquid extraction (PLE). Firstly, the solid sample, wetted with the extraction solvent, was enclosed into tailor-made bags prepared with low density polyethylene. Secondly, these packages were submitted to a conventional PLE (70 °C, 4 cycles of 5 min static time). Finally, the analytes were determined by liquid chromatography–atmospheric pressure photoionisation–tandem mass spectrometry. The main advantage of this procedure is the reduction of time, solvent and labour effort ought to the combination of extraction and clean-up in a single step. Although the extraction is not quantitative (thus, standard addition is recommended for quantification) selectivity is clearly gained using the membrane as a consequence of the differences of permeation and transport through the membrane between the analytes and other sample matrix components. The optimised protocol provides limits of detection ranging from 0.3 ng g⁻¹ (ethylhexyl dimethyl p-aminobenzoate (OD-PABA)) to 25 ng g⁻¹ (ethylhexyl triazone (EHT)) with only 0.5 g of sludge sample. All the studied UV filters were found in the samples at concentration levels between 1.4 and 2479 ng g⁻¹, emphasising the high adsorption potential of this kind of environmental pollutants onto solid samples such as sludge. Also, this method has permitted the determination of seven of the studied UV filters in sludge samples for the first time.     

An integrated analytical approach to diagnose the conservation state of building materials of a palace house in the metropolitan Bilbao (Basque Country, North of Spain)

Raman microprobe spectroscopy and μX-ray fluorescence were used to analyse the original composition and degradation products of the limestone and the sandstones from the facades of one historical building. Carbon particles, gypsum (CaSO₄·2H₂O) and some nitrate compounds were determined by Raman measurements, while elemental characterisation carried out by μXRF revealed the presence of lead, sulphur and copper as pollutants. On the one hand, the grey sandstone is the most deteriorated and in some cases pollutants reach 3 cm depth. On the other hand, quantification of soluble salts (chlorides, sulphates, nitrates, nitrites, fluorides and carbonates) was accomplished by ion chromatography. Chloride and sulphates are not significant soluble salts in the façades of the building, but the amount of nitrate is even 136 g kg⁻¹ in some of the most deteriorated samples and of 147 g kg⁻¹ in black-crusts. Finally, organic compounds (mainly PAHs) were characterised by GC-MS. Concentrations higher than 20 ppm of total PAHs were measured in the black-crusts of the rain-protected facades. The presence of certain PAHs indicated combustion of fuels as the main source of deterioration for the palace house building materials.     

Determination of halogenated hydrocarbons by flow injection ozone chemiluminescence

A flow injection gas phase chemiluminometer has been constructed for monitoring halogenated compounds which upon UV radiation consume ozone. The ozone concentration is followed by the ethylene-ozone chemiluminescent reaction and by UV absorption. The sensitivity depends on the ability of each compound to consume ozone and the limits of quantification vary from 9.6 and 25 nmol for CFCl₃ and CF₂Cl₂ to 22.5 and 17.2 μmol for CHCl₃ and CH₃CCl₃, respectively.     

A new method for the routine analysis of LAS and PAH in sewage sludge by simultaneous sonication-assisted extraction prior to liquid chromatographic determination

Linear alkylbenzene sulphonates (LAS) and polycyclic aromatics hydrocarbons (PAH) are organic pollutants in sewage sludge which will have to be monitored in the European Union according to the third draft of a future sludge directive. In the present work, an analytical method for the simultaneous extraction of 4 LAS homologues and 16 PAH congeners in sludge from wastewater treatment plants is proposed to improve the routine analysis of these compounds in sludge samples. The method involves sonication assisted extraction, clean-up and preconcentration by solid phase extraction, and determination by high-performance liquid chromatography with ultraviolet diode array (UV-DAD) and fluorescence (FLD) detectors. Average recoveries were 87% for LAS and 76% for PAH, with relative standard deviations below 13%. Limits of quantification of LAS and PAH were in the range from 13 to 56 mg kg⁻¹ and from 80 to 650 μg kg⁻¹, respectively, when using UV-DAD. Limits of quantification of LAS and PAH were in the range 5-18 mg kg⁻¹ and from 1 to 150 μg kg⁻¹, respectively, when using FLD. The applicability of the proposed method was evaluated by the determination of these compounds in sludge from wastewater treatment plants in Seville (South Spain).     

Determination of polycyclic aromatic hydrocarbons by gas chromatography — ion trap tandem mass spectrometry and source identifications by methods of diagnostic ratio in the ambient air of Campo Grande, Brazil

Polycyclic aromatic hydrocarbons (PAHs) were measured in samples collected from July to December of 2003, in Campo Grande — MS (Brazil), on three different sites: Ary Coelho Square (AC), Indigenous Nations' Park (NI) and Indubrasil (IB). Particle-bound PAHs were collected on quartz filters and gas-phase PAHs on glass cartridges using a polyurethane foam sampler, respectively. The substances of interest were extracted with a dichloromethane/methanol mixture (9:1 v/v) and subjected to gas chromatography — ion trap tandem mass spectrometry (GC-MS/MS). The concentration values of PAHs in AC varied from 0.03 to 26.28 μg m^− 3 and the average value for the sum of 16 PAHs was 51.35 μg m^− 3 (range: 2.98-79.91 μg m^− 3). On the NI site were obtained values of PAHs with concentrations of between 0.02 and 13.84 μg m^− 3 and an average value for the total of 16 PAHs was equal to 46.76 μg m^− 3 (range: 21.20-85.32 μg m^− 3). The PAH concentrations obtained in the IB sampling site varied from 0.02 to 16.74 μg m^− 3, with the obtained medium value, for the total of 16 PAHs, equal to 42.79 μg m^− 3 (range: 26.53-58.49 μg m^− 3). Strong positive correlations were found among samples (r: 0.70 to 0.97, p < 0.005) in 39% of the associations and non-significant correlations were observed among PAHs, except for Flu-Acy, BaA-Phe, Chry-BaA, BkF-Naph, BaP-Phe and BghiP-Naph that were poorly correlated. The statistical analysis of the data showed high similarity among samples on the three sites. The diagnostic ratios indicated the vehicular traffic (diesel and gasoline engines) and the biomass combustion, as major PAH sources in the three sampling sites.     

Enrichment of polycyclic aromatic hydrocarbons in seawater with magnesium oxide microspheres as a solid-phase extraction sorbent

The enrichment of polycyclic aromatic hydrocarbons (PAHs) in water samples with magnesium oxide (MgO) microspheres was evaluated, and four 3-5-ring PAHs were used as probes to validate the adsorption capacity of the material. Factors affecting the recovery of PAHs were investigated in detail, including the type and concentration of organic modifiers, elution solvents, particle size of the adsorbent, volume and flow rate of the samples, and the lifetime of MgO cartridges. The recoveries of four PAHs extracted from 20 mL of seawater spiked with standard PAHs ranged from 85.8% to 102.0% under the optimised conditions. The limits of detection varied from 1.83 ng L⁻¹ to 16.03 ng L⁻¹, indicating that the analytical method was highly sensitive. Additionally, the proposed method was successfully used to enrich PAHs in seawater. Compared to conventional methods, the proposed method consumed less organic modifier (5% acetone), and cheaper sorbents with comparable extraction efficiency were employed.     

Application of sulfur microparticles for solid-phase extraction of polycyclic aromatic hydrocarbons from sea water and wastewater samples

The application of sulfur microparticles as efficient adsorbents for the solid-phase extraction (SPE) and determination of trace amounts of 10 polycyclic aromatic hydrocarbons (PAHs) was investigated in sea water and wastewater samples using high performance liquid chromatography coupled with an ultraviolet detector (HPLC–UV). Parameters influencing the preconcentration of PAHs such as the amount of sulfur, solution flow rate and volume, elution solvent, type and concentration of organic modifier, and salt effect were examined. The results showed that at a flow rate of 10 mL min⁻¹ for the sample solutions (100 mL), the PAHs could be adsorbed on the sulfur microparticles and then eluted by 2.0 mL of acetonitrile. For HPLC–UV analysis of extracted PAHs, the calibration curves were linear in the range of 0.05–80.0 μg L⁻¹; the coefficients of determinations (r²) were between 0.9934 and 0.9995. The relative standard deviations (RSDs) for eight replicates at two concentration levels (0.5 and 4.0 μg L⁻¹) of PAHs were lower than 7.3%, under optimized conditions. The limits of detection (LODs, <!-- no-mfc -->S/N<!-- /no-mfc --> = 3) of the proposed method for the studied PAHs were 0.007–0.048 μg L⁻¹. The recoveries of spiked PAHs (0.5 and 4 μg L⁻¹) in the wastewater and sea water samples ranged from 78% to 108%. The simplicity of experimental procedure, high extraction efficiency, short sample analysis, and using of low cost sorbent demonstrate the potential of this approach for routine trace PAH analysis in water and wastewater samples.     

n-Alkanes, PAHs and surfactants in the sea surface microlayer and sea water samples of the Gerlache Inlet sea (Antarctica)

Sea surface microlayer (SML) and sea water samples (SSW) collected in the Gerlache Inlet Sea (Antarctica) were analysed for n-alkanes and polycyclic aromatic hydrocarbons (PAHs). The SML is a potential enrichment site of hydrophobic organic compounds compared to the underlying water column. Total concentration ranges of n-alkanes and PAHs (dissolved and particulate) in subsurface water (− 0.5 m depth) were 272-553 ng l^− 1 (mean: 448 ng l^− 1) and 5.27-9.43 ng l^− 1 (mean: 7.06 ng l^− 1), respectively. In the SML, the concentration ranges of n-alkanes and PAHs were 353-968 ng l^− 1 (mean: 611 ng l^− 1) and 7.32-23.94 ng l^− 1 (mean: 13.22 ng l^− 1), respectively. To evaluate possible PAH contamination sources, specific PAH ratios were calculated. The ratios reflected a predominant petrogenic input. A characterisation of surface active substances was also performed on SML and SSW samples, both by gas bubble extraction, and by dynamic surface tension measurements. Results showed a good correlation between n-alkanes, PAHs and refractory organic matter.     

Simultaneous determination of sex hormones in egg products by ZnCl2 depositing lipid, solid-phase extraction and ultra performance liquid chromatography/electrospray ionization tandem mass spectrometry

A method was developed for simultaneous determination of residues of 17 sex hormones in egg products. Target compounds were extracted from samples with methanol in an ultrasonic bath, effectively separated from lipids in the extracts by ZnCl₂ depositing filtration and purified using a C₁₈ solid-phase extraction (SPE) and followed by NH₂ SPE cartridge. The analytes were quantified by liquid chromatography using a BEH C₁₈ column coupled to an electrospray ionization tandem mass spectrometer (LC-ESI-MS/MS) operating in negative mode for estrogens and in positive multiple reaction monitoring mode for androgens. The parameters of the mass spectrometer and the composition of mobile phase and additives were also optimized to enhance detection sensitivity. Average recoveries of the target compounds varied from 70.0% to 121.0% with relative standard deviations ranging from 2.3% to 11.2% at two fortification levels. The limits of detection (LOD) of the method were from 0.002 μg kg⁻¹ to 0.23 μg kg⁻¹ and the limits of quantification (LOQ) were in the range of 0.007-0.76 μg kg⁻¹.     

Speciation of chromium in waste water using ion chromatography inductively coupled plasma mass spectrometry

Ion chromatography (IC) coupled with inductively coupled plasma mass spectrometry (ICP-MS) was systematically investigated for determining the speciation of chromium in environmental samples. Firstly, the stability of complexes formed by Cr(III) with various aminopolycarboxylic acids was studied by electrospray ionization mass spectrometry (ESI-MS). The results showed that [Cr(EDTA)]⁻ was stable in solution. Secondly, various mobile phases were examined to separate Cl⁻ from chromium species by IC to avoid Cl⁻ interference. The separation of [Cr(EDTA)]⁻ and Cr(VI) was achieved on a new anion-exchange column (G3154A/102) using a mobile phase containing 20 mM NH₄NO₃ and 10 mM NH₄H₂PO₄ at pH 7.0 without Cl⁻ interference. Detection limits for chromium species were below 0.2 μg/L with a direct injection of sample and without prior removal of interferences from the matrix. Finally, the proposed method was used for the determination of chromium species in contaminated waters.     

Two rapid and sensitive automated methods for the determination of nitrite and nitrate in soil samples

Spectrophotometric flow injection methods were developed for the individual determination of nitrite or nitrate, and for the simultaneous determination of nitrite and nitrate, in soil samples. Nitrite was determined directly using a modified version of the Griess-Ilosvay diazo-coupling reaction, measuring at 543 nm the absorbance of the azo-dye complex formed. Simultaneous nitrite and nitrate determinations were based on on-line nitrate reduction in a micro column containing copperised cadmium. A single chromogenic reagent containing all the necessary reactants was used in both methods. For determinations, the chemical and instrumental variables were optimised by univariate analysis and simplex chemometric method. The optimised conditions gave a linear calibration range between 0.05 and 1.6 µg m L^− 1 for N-NO₂⁻ and between 0.05 and 7.0 µg m L^− 1 for N-NO₃⁻. The detection limits for nitrite and nitrate were 22 µg L^− 1 and 44 µg L^− 1 respectively. The proposed methods allowed up to 35-40 samples per hour to be analysed with good precision. The simultaneous method was successfully used for the determination of nitrite and nitrate in soil samples (the results obtained were validated against those obtained by reference methods). The proposed methods are simpler and faster than conventional methods and could be routinely used in environmental monitoring laboratories.