Improved surface-enhanced Raman scattering on optimum electrochemically roughened silver substrates

In this work, the effects of preparation conditions used in roughening silver substrates by electrochemical triangular-wave oxidation-reduction cycles (ORC) on surface-enhanced Raman scattering (SERS) were first investigated. The optimum roughening conditions for obtaining strongest SERS of Rhodamine 6G (R6G) are as follows. Ag electrodes were cycled in deoxygenated aqueous solutions containing 0.1 M NaCl from −0.3 to +0.2 V versus Ag/AgCl at 25 mV s⁻¹ for five scans. The SERS of R6G adsorbed on this optimum procedure-prepared roughened Ag substrate exhibits a higher intensity by one order of magnitude, as compared with that of R6G adsorbed on a normally roughened Ag substrate.     

Direct evidence of chemical effect of surface-enhanced Raman scattering observed on electrochemically prepared rough gold substrates

In this study, polypyrrole (PPy) films were electrochemically deposited on gold substrates roughened by an electrochemical triangular-wave oxidation-reduction cycles (ORC) in an aqueous solution containing 0.1N KCl. Then the substrates were heated from 25 to 50 °C and the corresponding SERS performances of PPy were observed in situ. The results indicate that the SERS enhancement capabilities of substrates are gradually raised from 25 °C to a maximum at 40 °C and monotonically decreased from 40 to 50 °C. These SERS enhancement capabilities ascribed to the charge transfers from PPy to Au, which are responsible for the chemical effects of SERS mechanisms, are successfully observed via SERS and high resolution X-ray photoelectron spectroscopy (HRXPS) analyses. The variation in content of the oxidized PPy peak of the double peaks in the range of 1000-1150 cm⁻¹ in SERS spectrum obtained on an Au substrate at different temperatures is consistent with its corresponding variation in the SERS intensity of PPy. The variation in content of the oxidized nitrogen of PPy deposited on an Au substrate at different temperatures revealed from an HRXPS analysis also confirms this consistence.     

Photochemical decoration of silver nanoparticles on magnetic microspheres as substrates for the detection of adenine by surface-enhanced Raman scattering

In this work, silver nanoparticles (AgNPs) decorated magnetic microspheres (MMs) are prepared as surface-enhanced Raman scattering (SERS) substrate for the analysis of adenine in aqueous solutions. To prepare these substrates, magnetic particles were first synthesized by coprecipitation of Fe(II) and Fe(III) with ammonium hydroxide. A thin layer of cross-linked polymer was formed on these magnetic particles by polymerization through suspension of magnetic particles into a solution of divinyl benzene/methyl methacrylate. The resulted polymer protected magnetic particles are round in shape with a size of 80 μm in diameter. To form AgNPs on these MMs, photochemical reduction method was employed and the factors in photochemical reduction method were studied and optimized for the preparation of highly sensitive and stable AgNPs on MMs substrates (abbreviated as AgMMs substrates). By dispersing the AgMMs in aqueous samples, cylindrical magnet was used to attract the AgMMs for SERS detections. The observed enhancement factor of AgMMs reached 7 orders in magnitude for detection of adenine with a detection limit approaching to few hundreds of nanomolar.     

Effects of electrolytes used in roughening gold substrates by oxidation–reduction cycles on surface-enhanced Raman scattering

In this work, the effects of electrolytes used in roughening gold substrates by electrochemical methods on surface-enhanced Raman scattering (SERS) were first investigated. First, gold substrates were roughened by triangular-wave oxidation–reduction cycles (ORC) in aqueous solutions containing different kinds of 0.1 M electrolytes. Then Rhodamine 6G (R6G) was used as Raman probe to examine this effect of electrolytes used on the SERS observed. The result indicates that the highest intensity of SERS of R6G was obtained on the roughened Au substrate prepared in 0.1 M NaCl, which was less used in the literature. Meanwhile, it was also found that the rougher surface morphology observed, which is contributive to the higher SERS obtained, is corresponding to the smaller cathodic peak area shown in the cyclic voltammograms for roughening the Au substrate.     

Cuttlebone-derived organic matrix as a scaffold for assembly of silver nanoparticles and application of the composite films in surface-enhanced Raman scattering

Biologically derived materials provide a rich variety of approaches toward new functional materials because of their fascinating structures and environment-friendly features, which is currently a topic of research interest. In this paper, we show that the cuttlebone-derived organic matrix (CDOM) is an excellent scaffold for the one-step synthesis and assembly of silver nanoparticles (AgNPs), which can be further used as substrate for surface-enhanced Raman scattering (SERS). Formation of AgNPs–CDOM composite was accomplished by the reaction of CDOM with AgNO₃ and NH₃·H₂O solution at 80 °C without using any other stabilizer and reducing agents. UV–vis spectra and TEM were utilized to characterize the AgNPs and investigate their formation process. Results demonstrate that the size and distribution of AgNPs can be partly regulated by changing incubation time; the concentration of NH₃·H₂O is critical to the formation rate of AgNPs. As a proof of principle, we show that the AgNPs–CDOM composite can be employed in trace analysis using SERS.     

Highly reproducible surface-enhanced Raman scattering-active Au nanostructures prepared by simple electrodeposition: Origin of surface-enhanced Raman scattering activity and applications as electrochemical substrates

The fabrication of effective surface-enhanced Raman scattering (SERS) substrates has been the subject of intensive research because of their useful applications. In this paper, dendritic gold (Au) rod (DAR) structures prepared by simple one-step electrodeposition in a short time were examined as an effective SERS-active substrate. The SERS activity of the DAR surfaces was compared to that of other nanostructured Au surfaces with different morphologies, and its dependence on the structural variation of DAR structures was examined. These comparisonal investigations revealed that highly faceted sharp edge sites present on the DAR surfaces play a critical role in inducing a high SERS activity. The SERS enhancement factor was estimated to be greater than 10⁵, and the detection limit of rhodamine 6G at DAR surfaces was 10⁻⁸ M. The DAR surfaces exhibit excellent spot-to-spot and substrate-to-substrate SERS enhancement reproducibility, and their long-term stability is very good. It was also demonstrated that the DAR surfaces can be effectively utilized in electrochemical SERS systems, wherein a reversible SERS behavior was obtained during the cycling to cathodic potential regions. Considering the straightforward preparation of DAR substrates and the clean nature of SERS-active Au surfaces prepared in the absence of additives, we expect that DAR surfaces can be used as cost-effective SERS substrates in analytical and electrochemical applications.     

Silver-particle-based surface-enhanced resonance Raman scattering spectroscopy for biomolecular sensing and recognition

We demonstrate in this work that 2-μm-sized Ag (μAg) powders can be used as a core material for constructing biomolecular sensing/recognition units operating via surface-enhanced resonance Raman scattering (SERRS). This is possible because μAg powders are very efficient substrates for both the diffuse reflectance IR and the surface-enhanced Raman scattering–SERRS spectroscopic characterization of molecular adsorbates prepared in a similar manner on silver surfaces. Besides, the agglomeration of μAg particles in a buffer solution can be prevented by the layer-by-layer deposition of cationic and anionic polyelectrolytes such as poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA). In this particular study, we used rhodamine B isothiocyanate (RhBITC) as a SERRS marker molecule, and μAg powders adsorbed consecutively with RhBITC and PAH–PAA bilayers were finally derivatized with biotinylated poly(l-lysine). On the basis of the nature of the SERRS peaks of RhBITC, those μAg powders were confirmed to selectively recognize streptavidin molecules down to concentrations of 10⁻¹⁰ g mL⁻¹. Since a number of different molecules can be used as SERS–SERRS marker molecules, the present method proves to be an invaluable tool for multiplex biomolecular sensing/recognition via SERS and SERRS.     

Partition layer-modified substrates for reversible surface-enhanced Raman scattering detection of polycyclic aromatic hydrocarbons

Herein, we present progress towards an analytical sensor for polycyclic aromatic hydrocarbons (PAHs) using surface-enhanced Raman scattering (SERS) on partition layer-modified nanostructured substrates. Specifically, a 1-decanethiol monolayer has been assembled on a silver film over nanospheres substrate to concentrate PAHs within the zone of SERS detection. Both anthracene and pyrene were detected with limits of detection at 300 and 700 pM, respectively. The measured SERS spectra allowed for easy distinction of the two PAH compounds, due to varying peak locations, and insight into the partitioning mechanism. Additionally, exposure to a common environmental interferant, Suwannee River fulvic acid, did not impede the measurement of the PAHs, and the sensor is reusable after a short exposure to 1-octanol. Finally, the utility of this sensing platform for PAH detection was compared to that achievable for other classes of organic pollutants such as polychlorinated biphenyls and polybrominated diphenyl ethers. Figure SERS detection of polycyclic aromatic hydrocarbons facilitated via partition layer modified substrates.

In-situ surface-enhanced Raman scattering and FT-Raman spectroscopy of black prints

The black inkjet and laser prints were analysed with regard to application in forensic analysis of questioned documents. The purpose of this work was to study spectral properties and compare the suitability of surface-enhanced Raman scattering (SERS) with Fourier transform Raman spectra of prints. This work aimed to find optimal surface-enhanced Raman spectroscopic approach for the future analysis of documents using statistical methods. In this work, we analysed eight prints of four laser and four inkjet devices. The samples were measured using two dispersive Raman devices; (DXR Raman microscope with excitation line 532 nm, Foram 685-2 spectrometer − 685 nm) and FT-Raman device (Bruker Spectrometer MultiRAM with excitation line 1064 nm). The silver nanoparticles (AgNPs) colloid for SERS experiment were synthesised and checked by UV–vis spectroscopy and scanning electron microscopy (SEM). The remarkable differences caused by centrifugation of silver colloid were observed just in the SEM images. The main contribution of this paper is to propose the novel approach achieving sufficient SERS signal intensity of black prints using the both, laser and inkjet printers. Moreover, this method is based on just a single metal colloid, and the analysis can be performed in-situ, i.e. directly on the printed sample surface. We consider the SERS could by highly promising and universal for applications in the forensic analysis of printed documents with the combination of statistical method when conventional methods are not effective.     

Interaction of soil humic acids with herbicide paraquat analyzed by surface-enhanced Raman scattering and fluorescence spectroscopy on silver plasmonic nanoparticles

A study of the interaction between paraquat (methyl viologen) and humic acids, extracted from a soil amended over 30 years with crop residues, cow slurries and cattle manure, was carried out by two emission spectroscopies based on plasmonic effects: surface-enhanced Raman scattering (SERS) and surface-enhanced fluorescence (SEF). To carry out this study Ag nanoparticles were used. The complex formation was tested by analyzing the effect of the herbicide on humic acids, and by varying experimental parameters such as the pH and the laser excitation wavelength. The study of the vibrational bands led to infer information about the interaction mechanism of paraquat with humic acids and to find a correlation between this interaction and the humic acids structural modification induced by the different amendments added to soil.     

A simple approach for ultrasensitive detection of bisphenols by multiplexed surface-enhanced Raman scattering

Bisphenol A (BPA) is well known for its use in plastic manufacture and thermal paper production despite its risk of health toxicity as an endocrine disruptor in humans. Since the publication of new legislation regarding the use of BPA, manufacturers have begun to replace BPA with other phenolic molecules such as bisphenol F (BPF) and bisphenol B (BPB), but there are no guarantees regarding the health safety of these compounds at this time. In this context, a very simple, cheap and fast surface-enhanced Raman scattering (SERS) method was developed for the sensitive detection of these molecules in spiked tap water solutions. Silver nanoparticles were used as SERS substrates. An original strategy was employed to circumvent the issue of the affinity of bisphenols for metallic surfaces and the silver nanoparticles surface was functionalized using pyridine in order to improve again the sensitivity of the detection. Semi-quantitative detections were performed in tap water solutions at a concentrations range from 0.25 to 20 μg L⁻¹ for BPA and BPB and from 5 to 100 μg L⁻¹ for BPF. Moreover, a feasibility study for performing a multiplex-SERS detection of these molecules was also performed before successfully implementing the developed SERS method on real samples.     

Sonoelectrochemical synthesis of spike-like gold-silver alloy nanoparticles from bulk substrates and the application on surface-enhanced Raman scattering

The synthesis of non-spherical spike-like gold-silver alloy nanoparticles on platinum substrates was first developed by sonoelectrochemical methods in this study. First, a silver substrate was roughened by a triangular-wave oxidation-reduction cycle (ORC) in an aqueous solution containing 0.1 M HCl. Silver-containing complexes were found in the solution after the ORC treatment. Then a gold substrate was subsequently roughened by the similar ORC treatment in the same silver complexes-containing solution. After this procedure, Au- and Ag-containing complexes were left in the solution. Subsequently, the Au working electrode was immediately replaced by a Pt electrode. A cathodic overpotential was applied under controlled sonication and slight stirring to synthesize Au-Ag alloy nanoparticles on the Pt substrate. Encouragingly, the surface-enhanced Raman scattering (SERS) of Rhodamine 6G on the Au-Ag alloy nanoparticles-deposited Pt substrate exhibits a higher intensity by eight-fold of magnitude and a better resolution, as compared to that obtained on the Au nanoparticles-deposited Pt substrate.     

Low-frequency surface-enhanced Raman scattering spectroscopy at metal electrode surfaces

Low-frequency surface-enhanced Raman scattering (SERS) spectroscopy is a versatile tool for studying surface phenomena under electrochemical conditions. This spectroscopy enables us to obtain rich information on extramolecular vibrations between substrate and adsorbates, which are sensitive to atomistic surface features of the substrate. Owing to recent advancements in optical filter technology, low-frequency SERS signals are now becoming easily detectable using conventional Raman systems equipped with holographic notch filters. In addition, SERS background signals, which have been simply ignored, can provide electronic information on the metal substrate. This allows us to observe both sides of electrode–electrolyte interfaces in situ and simultaneously, which is never expected in far-infrared or terahertz absorption spectroscopy. This advanced SERS spectroscopy can help our understanding of electrochemical and electrocatalytic reactions at the molecular scale.     

Quantitative analysis of methyl green using surface-enhanced resonance Raman scattering

Surface-enhanced resonance Raman scattering (SERRS) spectra of aqueous solutions of the triphenylmethane dye methyl green have been obtained for the first time by use of citrate-reduced silver colloids and a laser excitation wavelength of 632.8 nm. Given the highly fluorescent nature of the analyte, which precluded collection of normal Raman spectra of the dye in solution and powdered state, it was highly encouraging that SERRS spectra showed no fluorescence due to quenching by the silver sol. The pH conditions for SERRS were optimised over the pH range 0.5–10 and the biggest enhancement for SERRS of this charged dye was found to be at pH 2.02, thus this condition was used for quantitative analysis. SERRS was found to be highly sensitive and enabled quantitative determination of methyl green over the range 10⁻⁹ to 10⁻⁷ mol dm⁻³. Good fits to correlation coefficients were obtained over this range using the areas under the vibrational bands at 1615 and 737 cm⁻¹. Finally, a limit of detection of 83 ppb was calculated, demonstrating the sensitivity of the technique.     

Surface-enhanced Raman scattering detection of cholinesterase inhibitors

A new sensitive surface-enhanced Raman scattering (SERS) assay for detection of cholinesterase inhibitors such as organophosphorous pesticides using silver colloidal nanoparticles was developed and optimized. Acetylcholinesterase (AChE) mediated the hydrolysis of acetylthiocholine to produce thiocholine, which interacted with the silver nanoparticles to give a specific SERS spectrum. Variation in enzyme activity due to inhibition was measured from changes in intensity of a characteristic peak (772 cm⁻¹) of the SERS spectrum that was directly correlated with the concentration of produced thiocholine. The method was demonstrated for the detection of paraoxon as reference AChE inhibitor. Limit of detection of paraoxon for 5 min incubation at 25 °C was 1.8 × 10⁻⁸ M. This assay can be utilized for the detection of trace amounts of any AChE inhibitor.     

One-pot synthesis of silver colloid with body-heat for surface-enhanced Raman spectroscopy detections

In this study, a convenient method of preparing the substrate is proposed with one-pot synthesis of silver colloid under body heat, and the SERS detection uses the fresh substrate to avoid the drawback of substrates' short life of use. The synthesis of silver colloid is carried out in a 10 mL vial by using ascorbic acid as a reductant and trisodium citrate as a stabilizer. The vial is grasped with the palm of the experimenter for several minutes without shaking. The proposed method is simple, rapid, green energy and cost-effective. By adjusting the concentration of trisodium citrate, not only the particle size can be controlled from about 110 nm to 50 nm but also the homogeneity of nanoparticles can be improved. As a SERS substrate, the silver colloid has high batch reproducibility and showed good SERS activity. The relative standard deviation between different manufacturers is 5.51% when the substrate of silver colloid is used for the detection of rhodamine 6 G. Using the substrate, the lowest detection concentrations of rhodamine 6 G, crystal violet, enrofloxacin, melamine and leucomalachite green are 1.0×10~(-8), 6.1×10~(-8),1.4 × 10~(-6), 7.1 ×10~(-5) and 5.1 ×10~(-8) mol/L, respectively. Results demonstrate that the developed method has the advantage of convenience and high efficiency in the field preparation of reliable SERS substrate.     

Temporal evolution of Raman intensities on surface-enhanced Raman scattering active copper and gold electrodes at negative potentials

The effect of a roughening procedure on surface-enhanced Raman scattering (SERS) intensity of pyridine at copper and gold electrodes subjected to negative potential has been investigated. Among four procedures tested for a copper electrode the one consisting of electrochemical activation in a solution of LiCl and CuCl₂ resulted in the most stable and effective surface. It was proved that the presence of pyridine during the pretreatment procedure caused a very fast, irreversible decay of SERS intensity for both copper and gold electrodes. Quite stable, at least at room temperatures, gold surfaces were obtained by oxidation-reduction cycles activation in KCl solution.     

Fabrication of bimetallic microfluidic surface-enhanced Raman scattering sensors on paper by screen printing

Au–Ag bimetallic microfluidic, dumbbell-shaped, surface enhanced Raman scattering (SERS) sensors were fabricated on cellulose paper by screen printing. These printed sensors rely on a sample droplet injection zone, and a SERS detection zone at either end of the dumbbell motif, fabricated by printing silver nanoparticles (Ag NPs) and gold nanoparticles (Au NPs) successively with microscale precision. The microfluidic channel was patterned using an insulating ink to connect these two zones and form a hydrophobic circuit. Owing to capillary action of paper in the millimeter-sized channels, the sensor could enable self-filtering of fluids to remove suspended particles within wastewater without pumping. This sensor also allows sensitive SERS detection, due to advantageous combination of the strong surface enhancement of Ag NPs and excellent chemical stability of Au NPs. The SERS performance of the sensors was investigated by employing the probe rhodamine 6G, a limit of detection (LOD) of 1.1 × 10⁻¹³ M and an enhancement factor of 8.6 × 10⁶ could be achieved. Moreover, the dumbbell-shaped bimetallic sensors exhibited good stability with SERS performance being maintained over 14 weeks in air, and high reproducibility with less than 15% variation in spot-to-spot SERS intensity. Using these dumbbell-shaped bimetallic sensors, substituted aromatic pollutants in wastewater samples could be quantitatively analyzed, which demonstrated their excellent capability for rapid trace pollutant detection in wastewater samples in the field without pre-separation.     

Characteristics of the ring stretching of oxidized polypyrrole on the surface-enhanced Raman spectrum

In this study, polypyrrole (PPy) films were electropolymerized under different preparation conditions on rough gold substrates. The peak shown at the higher frequency of the double peaks at about 1329 and 1386 cm^–1 in surface-enhanced Raman scattering of PPy was initially assigned to the ring stretching of oxidized PPy. A systematic study was carried out to confirm this assignment. It was found that the conductivity of PPy was strongly related to and increased with this Raman peak intensity of oxidized PPy. Meanwhile, the normalized relative intensities of this Raman peak for various PPy films are consistent with their corresponding doping levels. Electronic Publication     

A surface-enhanced Raman scattering method for detection of trace glutathione on the basis of immobilized silver nanoparticles and crystal violet probe

Unsatisfactory sensitivity and stability for molecules with low polarizability is still a problem limiting the practical applications of surface-enhanced Raman scattering (SERS) technique. By preparing immobilized silver nanoparticles (Fe₃O₄/Ag) through depositing silver on the surface of magnetite particles, a highly sensitive and selective SERS method for the detection of trace glutathione (GSH) was proposed on the basis of a system of Fe₃O₄/Ag nanoparticles and crystal violet (CV), in which the target GSH competed with the CV probe for the adsorption on the Fe₃O₄/Ag nanoparticles. Raman insensitive GSH replaced the highly Raman sensitive CV adsorbed on the surface of Fe₃O₄/Ag particles. This replacement led to a strong decrease of the CV SERS signal, which was used to determine the concentration of GSH. Under optimal conditions, a linear response was established between the intensity decrease of the CV SERS signal and the GSH concentration in the range of 50–700 nmol L⁻¹ with a detection limit of 40 nmol L⁻¹. The use of a Fe₃O₄/Ag substrate provided not only a great SERS enhancement but also a good stability, which guarantees the reproducibility of the proposed method. Its use for the determination of GSH in practical blood samples and cell extract yielded satisfactory results.