Thermodynamic parameters of solids at high pressures from vibrational spectroscopy: MgO and MgAl2O4

Abstract

The effect of pressure on the optical or acoustic modes in the sideband fluorescence of Cr³⁺ doped into the MgO and MgAl₂O₄ lattices was identical to that measured for the corresponding Raman and infrared modes of MgAl₂O₄ and ultrasonic sound velocities (Chang and Barsch 1973, Jackson and Niesler 1982) for both MgO and MgAl₂O₄. This shows that the impurity cation does not measurably perturb the crystal lattice vibrations and thus may be used to probe the thermodynamic properties of such cubic materials at high pressures. The effect of pressure on the heat capacity, C_V, and entropy, S, of MgO and MgAl₂O₄ spinel was determined using statistical thermodynamics on the lattice vibrations measured to over 200 kbar. The results for MgO are identical to predictions from Debye theory to at least 10% compression.     

Luminescence channels of manganese-doped spinel

Two independent luminescence channels are observed from manganese-doped spinel Mn:MgAl₂O₄. The luminescence around 520 nm is assigned to transition from the lowest electronic excited state ⁴T₁ to the ground state ⁶A₁ of Mn²⁺ (3d)⁵ ion by analyzing the excitation spectrum and electron spin resonance measurement. The emission at 650 nm is triggered by the band edge excitation and is assigned similarly to the charge-transfer process associated with the manganese ion.     

Electrochemical activities of yttrium doped spinel LiMn2O4

It was found for the first time that the catalysis of yttrium doping of spinel LiMn₂O₄ can enhance the electrochemical activities of manganese, leading to both improvement of electrochemical capacity and reactivity with the electrolyte of manganese. A proper amount of doping was 0.5%, and such yttrium-doped sample, Li(Y_0.005Mn_0.995)₂O₄, had an initial capacity of 130 mAh g⁻¹ over that of the undoped one with the capacity retention to reach 92.3% exceeding that of the undoped one at 100th cycle.     

Preparation of TiO2-coated LiMn2O4 by carrier transfer method

The TiO₂-coated LiMn₂O₄ has been prepared by a carrier transfer method and investigated. This novel synthetic method involved the transfer of TiO₂ into the surface of LiMn₂O₄ with Vulcan XC-72 active carbon powders as a dispersant. The X-ray diffraction shows that spinel structure of materials does not change after the coating of TiO₂. The electrochemical performance tests show that the initial discharge capacity of TiO₂-modified LiMn₂O₄ is 111.5 mA h g⁻¹, which is better than that of pristine LiMn₂O₄ (103.8 mA h g⁻¹). The cyclic performance is significantly improved after surface modification. The TiO₂-modified LiMn₂O₄ by a carrier transfer method exhibits better discharge capability and lower resistance.     

尖晶石结构自旋有序CaTi2O4单晶生长和磁化率特性研究

通过助溶剂熔融法并在氩气气氛炉中成功生长出高质量大尺寸的CaTi₂O₄的单晶.X射线衍射实验及能量损失谱EDS证实,制备的CaTi₂O₄单晶晶胞参数a=9.781?,b=9.966?,c=3.148?,所有样品均为单相,且符合化学计量比,样品高纯.通过直流磁化率的测量,首次给出了晶体的Van-Vleck顺磁因子为6.85×10^-5cm³/mol,Cure-Weiss温度为-0.44 K,呈弱反铁磁性.同时,通过单晶各向磁化率的测量,进一步确认了CaTi₂O₄晶体中一维有序Ti-Ti反铁磁dimer链的形成,并明确了其方向. 关键词： 2O₄')" href="#">CaTi₂O₄ 磁化率 各向异性 反铁磁二聚化     

Preparation and characterization of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanorod by low heating solid state coordination method

Cathode material LiMn₂O₄ nanorod was prepared by annealing of the mixed precursor which was synthesized by low heating solid state coordination method using lithium acetate, manganese acetate and oxalic acid as starting materials. The structures and morphologies of the LiMn₂O₄ nanorod were investigated as a function of annealing temperature and time. The results showed that all samples in different annealing temperatures and time have the same spinel structure. The higher the annealing temperature is, the more complete the crystal structure forms, and the larger the particle size is. In addition, the electrochemical properties of the LiMn₂O₄nanorod were studied in this paper.     

ZnFe2O4的固相法和水热法制备及其电化学性能研究

本文用固相反应法和水热法制备了ZnFe₂O₄材料,X射线衍射(X-ray diffraction, XRD)表明制备出来的ZnFe₂O₄为尖晶石结构,表面形貌测试 (scanning electron microscopy, SEM) 显示两种方法制备的材料的平均粒径分别为500 nm和200 nm.比表面积测试结果表明,两种方法制备的样品的比表面积分别为136.7 m² g^{-1关键词： 2O₄')" href="#">ZnFe₂O₄ 尖晶石结构 电化学性能 锂离子电池}     

Synthesis and characterization of pure and ZrO2-doped nanocrystalline CuO-NiO system

The physicochemical, surface and catalytic properties of pure and doped 0.25CuO-NiO solids prepared by sol-gel method were investigated. The dopant concentration was 2, 4 and 6 mol% ZrO₂. The solids investigated were calcined at 400 and 600 °C. The techniques employed were XRD, EDX, TEM, surface excess oxygen, nitrogen adsorption at −196 °C and catalytic oxidation of CO by O₂ using both static and flow methods. The results revealed that the investigated system dissolved 4 mol% ZrO₂ by heating at 400 °C. This process was accompanied by a significant increase in the S_BET and V_p with subsequent decrease in the (r) values of the doped adsorbent. ZrO₂-doping of the system investigated followed by calcination at 400 and 600 °C led to a considerable increase in its catalytic activity in CO oxidation by O₂ using static and flow methods. The doping process was not accompanied by any change in the activation energy of the catalyzed reaction.     

Enhanced cyclability of triple-metal-doped LiMn2O4 spinel as the cathode material for rechargeable lithium batteries

To improve the cycle performance of spinel LiMn₂O₄ as the cathode of 4-V-class lithium secondary batteries, spinel phases LiM _x Mn_2 − x O₄ (M=Li, Fe, Co; x = 0, 0.05, 0.1, 0.15) and LiFe_0.05M _y Mn_{1.95 − y} O₄ (M=Li, Al, Ni, Co; y = 0.05, 0.1) were successfully prepared using the sol–gel method. The spinel materials were characterized by powder X-ray diffraction (XRD), elemental analysis, and scanning electron microscopy. All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns. Electrochemical studies were carried out using the Li|LiM _x Mn_2 − x O₄ (M=Li, Fe, Co; x = 0, 0.05, 0.1, 0.15) and LiFe_0.05M _y Mn_{1.95 − y} O₄ (M=Li, Al, Ni, Co; y = 0.05, 0.1) cells. These cathodes were more tolerant to repeated lithium extraction and insertion than a standard LiMn₂O₄ spinel electrode in spite of a small reduction in the initial capacity. The improvement in cycling performance is attributed to the stabilization in the spinel structure by the doped metal cations.     

Electronic structure studies of the spinel CoFe2O4 by X-ray photoelectron spectroscopy

The spinel CoFe₂O₄ has been synthesized by combustion reaction technique. X-ray photoelectron spectroscopy shows that samples are near-stoichiometric, and that the specimen surface both in the powder and bulk sample is most typically represented by the formula (Co_0.4Fe_0.6)[Co_0.6Fe_1.4]O₄, where cations in parentheses occupy tetrahedral sites and those within square brackets in octahedral sites. The results demonstrate that most of the iron ions are trivalent, but some Fe²⁺ may be present in the powder sample. The Co 2p_3/2 peak in powder sample composed three peaks with relative intensity of 45%, 40% and 15%, attributes to Co²⁺ in octahedral sites, tetrahedral sites and Co³⁺ in octahedral sites. The O 1s spectrum of the bulk sample is composed of two peaks: the main lattice peak at 529.90 eV, and a component at 531.53 eV, which is believed to be intrinsic to the sample surface. However, the vanishing of the O 1s shoulder peak of the powder specimen shows significant signs of decomposition.     

Monochromatic blue-green and red emission of rare-earth ions in MgGa2O4 spinel

Pr³⁺-activated blue-green phosphor and Eu³⁺-activated red phosphor hosted in MgGa₂O₄ spinel have been prepared by a gel-assisted high-temperature calcination process, respectively. Both anion and cation vacancies in the host were formed by decreasing the Mg concentration in the reaction source. The induced vacancies provide possibility of the accommodation of the doped rare-earth ions with larger atomic size in the highly symmetrical spinel structure. Due to the efficient energy transfer from the spinel host to the sole 4f sub-level of the doped rare earths, monochromatic emissions with high efficiency can be obtained to allow the phosphors to find applications in solid-state laser device and other phosphors excited under low energy. The corresponding spectroscopic transition mechanism has been proposed in this work.     

多孔SiO2包裹磁性纳米颗粒Fe3O4的制备与表征

采用加热分解油酸铁法制备了Fe₃O₄磁性纳米颗粒,并用有机模板和反相微乳液相结合的方法将磁性纳米颗粒包裹在多孔二氧化硅中.用红外光谱(FTIR)研究了不同的处理方式对油酸铁表面官能团的影响及油酸的反应浓度和加热分解油酸铁的过程中升温速率对Fe₃O₄纳米颗粒的影响.结果表明,用乙醇和丙酮处理后的固态蜡状油酸铁表面的油酸基团会受到损害,将不利于加热分解时形成单分散性的Fe₃O₄纳 关键词： 3O₄纳米颗粒')" href="#">Fe₃O₄纳米颗粒 2包裹')" href="#">多孔SiO₂包裹 反相微乳液法 油酸铁     

Al掺杂的尖晶石型LiMn2O4的结构和电子性质

采用基于密度泛函理论的第一性原理方法, 在广义梯度近似(GGA)和GGA+U方法下对尖晶石型LiMn₂O₄及其Al掺杂 的尖晶石型LiAl_0.125Mn_1.875O₄晶体的结构和电子性质进行了计算. 结果表明: 采用GGA方法得到尖晶石型LiMn₂O₄是立方晶系结构, 其中的Mn离子为+3.5价, 无法解释它的Jahn-Teller 畸变. 给出的LiMn₂O₄能带结构特征也与实验结果不符. 而采用GGA+U方法得到在低温下的LiMn₂O₄和其掺杂 体系LiAl_0.125Mn_1.875O₄的晶体都是正交结构, 与实验一致. 也能明确地确定Mn的两种价态Mn³⁺/Mn⁴⁺的分布并且能够说明Mn³⁺O₆的z方向有明显的Jahn-Teller 畸变, 而Mn⁴⁺O₆则没有畸变. LiMn₂O₄的能带结构与实验比较也能够符合. 采用GGA+U方法对Al掺杂体系的LiAl_0.125Mn_1.875O₄的研究表明, 用Al替换一个Mn不会明显地改变晶体的电子性质, 但可以有效地消除Al³⁺O₆ 八面体的Jahn-Teller畸变, 从而改善正极材料LiMn₂O₄的性能, 这与电化学实验的观察结果相一致.     

The study of transition on NiFe2O4 nanoparticles prepared by co-precipitation/calcination

In this study, the NiFe₂O₄ nanoparticles have been prepared by co-precipitation and calcination process. Using a vibrating sample magnetometer (VSM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive spectrometer of X-ray (EDX), and X-ray photoelectron spectroscopy (XPS), the samples obtained by co-precipitation and then by further calcination have been analyzed. The experimental results show that the precursor synthesized by co-precipitation is the composite of both amorphous FeOOH and Ni(OH)₂, but has no amorphous NiFe₂O₄. The results of both EDX and XPS revealed that the FeOOH species is wrapped up by Ni(OH)₂ species. In the calcination process, the amorphous composite is dehydrated and transformed gradually into crystalline NiFe₂O₄ nanoparticles, with the metal ions diffusing. The reaction is different from the one used to prepare other ferrite (e.g., CoFe₂O₄, MnFe₂O₄, Fe₃O₄, etc.) nanoparticles directly by co-precipitation. With increasing calcination temperature, the NiFe₂O₄ grains grow and the magnetization is enhanced.     

Characterization and electrochemical performance of the spinel LiMn2O4 prepared from -MnO2

The preparation and characterization of the spinel LiMn₂O₄ obtained by solid state reaction from quasi-amorphous -MnO₂ is reported. A well-defined highly pure spinel was characterized from X-ray diffractograms. The average manganese valence of -MnO₂ and spinel samples was found to be 3.89±0.01 and 3.59±0.01, respectively. The electrochemical performance of the spinel was evaluated through cyclic voltammetry and chronopotentiometry. The voltammetric profiles obtained at 1 mV/s for the LiMn₂O₄ electrode in 1 M LiClO₄ dissolved in a 2:1 mixture of ethylene carbonate and dimethyl carbonate showed typical peaks for the lithium insertion/extraction reactions. The charge capacity of this electrode was found to be 110 mA h g⁻¹ for the first charge/discharge cycles.     

Mössbauer characterization of calcium–ferrite oxides prepared by calcining Fe2O3 and CaO

Calcium ferrite oxides were prepared by calcining a mixture powder of iron- and calcium oxide. The ⁵⁷Fe-Mössbauer spectra of the calcium ferrites oxides were measured, revealing that the products should be Ca₂Fe₂O₅ and CaFe₂O₄, the ratio of which was dependent of the Fe/Ca atomic ratio of the mixture powder.     

Synthesis hexagonal ZrW2O8 and its thermal properties

ZrW₂O₈ as the typical negative thermal expansion (NTE) material has attracted much attention for the potential applications in various fields such as tailored coefficient of thermal expansion (CTE) composites. The hexagonal ZrW₂O₈ (h-ZrW₂O₈), with the combination of ZrO₂ and WO₃ in a composite, was synthesized at a pressure of 2 GPa and the temperature between 600°C and 700°C. We found h-ZrW₂O₈ decomposes to ZrO₂+WO₃ oxides that start from 500°C and end at 800°C, and determined the CTE of h-ZrW₂O₈ is?16.3×10^?6°C^?1 in the temperature range from 150°C to 450°C. The results show that ZrW₂O₈ with a hexagonal structure is metastable and exhibits high NTE property like its cubic structure.     

Characterization of the metallic phase in nanocrystalline ZnAl2O4-supported Pt catalysts

In this study several complementary methods as XRD, HRTEM, O₂ and H₂ adsorption, as well as H₂-O₂ titration were used for characterization of the metallic phase in 0.5-3.0 wt.% Pt/ZnAl₂O₄ catalysts. Three nanocrystalline ZnAl₂O₄ spinels used as a supports were prepared by the solvothermal and co-precipitation method. It was found that irrespective of the preparation method they form very good support materials with a high capacity to achieve high platinum dispersion. O₂ and H₂ chemisorption data showed metal dispersion up to 90% and good correspondence with HRTEM results was observed. The H₂-O₂ titration method may be applied for determination of Pt dispersion only in the high-loaded Pt/ZnAl₂O₄ catalysts. The catalytic performances of Pt supported on the prepared spinels were evaluated in the propane total oxidation reaction.     

Infrared active phonon modes and ionicity of single crystal MgAl2O4

Near-normal incident infrared reflectivity spectra of （100） MgAl2O4 spinel single crystal have been measured at different temperatures in the frequency region between 50 and 6000 cm^-1. Eight infrared-active phonon modes are identified, which are fitted with the factorized form of the dielectric function. The dielectric property and optical conductivity of the MgAl2O4 crystal are analysed. From TO/LO splitting, the effective Szigeti charges and Born effective charges at different temperatures are calculated for studying the ionicity and the effect of polarization. Based on the relationship between the （LO-TO）1 splitting, which represents the transverse and longitudinal frequencies splitting of the highest energy phonon band in the reflectivity spectrum, and the ionic-covalent parameter, the four main phonon modes are assigned. MgA1204 can be considered as a pure ionic crystal and its optical characters do not change with decreasing temperature, so it may be used as a suitable substrate for high-Tc superconducting thin films.     

On the isotope effect of Tc in squaric acid (H2C4O4)

The phase transition mechanism in squaric acid is reviewed from the viewpoint of the pressure dependence of the O—H—O bond length (2R). The two-dimensional pressure effect on T_c is extracted from the hydrostatic pressure behaviour by taking account of the uniaxial stress applied perpendicular to the layer planes. The result shows that if 2R(H₂SQ) is stretched to 2R(D₂SQ) the phase transition temperature 7^H _c of H₂SQ coincides with T^D _c of D₂SQ. This result supports the suggestion that the phase transition mechanism is of the order-disorder type.