Synthesis and magnetic characterization of nickel ferrite nanoparticles prepared by co-precipitation route

Magnetic nanoparticles of nickel ferrite (NiFe₂O₄) have been synthesized by co-precipitation route using stable ferric and nickel salts with sodium hydroxide as the precipitating agent and oleic acid as the surfactant. X-ray diffraction (XRD) and transmission electron microscope (TEM) analyses confirmed the formation of single-phase nickel ferrite nanoparticles in the range 8-28 nm depending upon the annealing temperature of the samples during the synthesis. The size of the particles (d) was observed to be increasing linearly with annealing temperature of the sample while the coercivity with particle size goes through a maximum, peaking at ∼11 nm and then decreases for larger particles. Typical blocking effects were observed below ∼225 K for all the prepared samples. The superparamagnetic blocking temperature (T_B) was found to be increasing with increasing particle size that has been attributed to the increased effective anisotropy energy of the nanoparticles. The saturation moment of all the samples was found much below the bulk value of nickel ferrite that has been attributed to the disordered surface spins or dead/inert layer in these nanoparticles.     

Sol-gel preparation and characterization of CoFe2O4-SiO2 nanocomposites

Magnetic nanocomposites formed by cobalt ferrite particles dispersed in a silica matrix were prepared by a sol-gel process. The effects of the thermal treatment temperature and the salt concentration on the structural and magnetic properties of the composites were investigated. By controlling these parameters, CoFe₂O₄/SiO₂ nanocomposites with different crystallite size and magnetic properties were obtained. By increasing the annealing temperature and salt concentration, composites with a progressive increase in the coercive field and of the density of magnetization were produced. In particular, a nanocomposite, with a Fe/Si molar concentration of 21%, obtained by drying the gel at 150 °C and further annealing at 800 °C, has a coercivity of 2000 Oe, which is more than twice higher than the coercivity of bulk cobalt ferrite.     

X-ray diffraction studies on crystallite size evolution of CoFe2O4 nanoparticles prepared using mechanical alloying and sintering

Nanosized cobalt ferrite spinel particles have been prepared by using mechanically alloyed nanoparticles. The effects of various preparation parameters on the crystallite size of cobalt ferrite which includes milling time; ball-to powder weight ratio (BPR) and sintering temperature, were studied using X-ray diffractometer (XRD). Scherrer's equation was used to study the crystallite size evolution of the as-prepared materials. The results of the as-milled sample revealed that both milling time and BPR plays a role in determining the crystallite size of the milled powder. However, where sintering is involved, the sintering temperature results in grain growth, and thus plays a dominant role in determining the final crystallite size of the samples sintered at higher temperature (above 900 °C). From the vibrating-sample magnetometer (VSM) measurement it was observed that the coercivity of the as-milled samples without sintering is almost negligible, which is a type characteristic of superparamagnetic material. However, for the sintered samples, the saturation increases while coercivity decreases with increases sintering temperature.     

Exchange bias and vertical shift in CoFe2O4 nanoparticles

Magnetic properties of core–shell cobalt ferrite nanoparticles prepared by co-precipitation route in the range 15–48 nm have been studied. It is shown that the coercivity follows non-monotonic size dependence and exhibits a peak at around 26 nm. Field-cooled magnetization exhibited both horizontal (exchange bias) and vertical shifts. The exchange bias is understood as originating at the interface between a surface region (with structural and spin disorder) and a core ferrimagnetic region. The dependence of the exchange bias and vertical shift on the particle size and cooling field is found to have significant differences. These differences are explained in the light of recent results that suggest that there is a variation of the pinning strength amongst the interface spins and the vertical shift is affected by the more strongly pinned uncompensated spins.     

Microstructure and magnetic properties of FePt:Ag nanocomposite films on SiO2/Si(1 0 0)

FePt:Ag nanocomposite films were prepared by pulsed filtered vacuum arc deposition system and subsequent rapid thermal annealing on SiO₂/Si(1 0 0) substrates. The microstructure and magnetic properties were investigated. A strong dependence of coercivity and ordering of the face-central tetragonal structure on both Ag concentration and annealing temperature was observed. With Ag concentration of 22% in atomic ratio, the coercivity got to 6.0 kOe with a grain size of 6.7 nm when annealing temperature was 400 °C.     

Low-temperature ordering of L10 FePt phase in FePt thin film with AgCu underlayer

FePt (20 nm) films with AgCu (20 nm) underlayer were prepared on thermally oxidized Si (0 0 1) substrates at room temperature by using dc magnetron sputtering, and the films annealed at different temperature to examine the disorder–order transformation of the FePt films. It is found that the ordered L1₀ FePt phase can form at low annealing temperature. Even after annealing at 300 °C, the in-plane coercivity of 5.2 kOe can be obtained in the film. With increase in annealing temperature, both the ordering degree and coercivity of the films increase. The low-temperature ordering of the films may result from the dynamic stress produced by phase separation in AgCu underlayer and Cu diffusion into FePt phase during annealing.     

Effects of synthesis variables on the magnetic properties of CoFe2O4 nanoparticles

Cobalt ferrite nanoparticles (CoFe₂O₄) have been synthesized using precipitation in water solution with polyethylene glycol as surfactant. Influence of various synthesis variables included pH, reaction time and annealing temperature on the magnetic properties and particle sizes has also been studied. Structural identification of the samples was carried out using Thermogravimetric and Differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy, Scanning electron microscopy, High resolution transmission electron microscopy. Vibrating sample magnetometer was used for the magnetic investigation of the samples. Magnetic properties of nanoparticles show strong dependence on the particle size. The magnetic properties increase with pH of the precipitating medium and annealing temperature while the coercivity goes through a maximum, peaking at around 25 nm.     

Preparation and characterizations of SiO2-coated nanoparticles of Mn0.4Zn0.6Fe2O4

Core/shell nanoparticles consisting of a magnetic core of zinc-substituted manganese ferrite (Mn_0.4Zn_0.6Fe₂O₄) and a shell of silica (SiO₂) are prepared by a sol-gel method using tetraethyl orthosilicate (TEOS) as a precursor material for silica and salts of iron, manganese and zinc as the precursor of the ferrite. Three weight percentages of the shell materials of SiO₂ are used to prepare the coated nanoparticles. The X-ray diffractograms (XRD) of the coated and uncoated magnetic nanoparticles confirmed that the magnetic nanoparticles are in their mixed spinel phase in an amorphous matrix of silica. Particles sizes of the samples annealed at different temperatures are estimated from the width of the (3 1 1) line of the XRD pattern using the Debye-Sherrer equation. The information regarding the crystallographic structure together with the particles sizes extracted from the high-resolution transmission electron microscopy (HRTEM) of a few selected samples are in agreement with those obtained from the XRD. HRTEM observations revealed that particles are coated with silica. The calculated thickness is in agreement with that obtained from the HRTEM pictures. Hysteresis loops observed in the temperature range 300 down to 5 K and Mössbauer spectra at room temperature indicate superparamagnetic relaxation of the nanoparticles.     

Synthesis and magnetic properties of antiferromagnetic Co3O4 nanoparticles

Antiferromagnetic Co₃O₄ nanoparticles with diameter around 30 nm have been synthesized by a solution-based method. The phase identification by the wide-angle X-ray powder diffraction indicates that the Co₃O₄ nanoparticle has a cubic spinel structure with a lattice constant of 0.80843(2) nm. The image of field emission scanning electron microscope shows that the nanoparticles are assembled together to form nanorods. The magnetic properties of Co₃O₄ fine particles have been measured by a superconducting quantum interference device magnetometer. A deviation of the Néel temperature from the bulk is observed, which can be well described by the theory of finite-size scaling. An enhanced coercivity as well as a loop shift are observed in the field-cooled hysteresis loop. The exchange bias field decreases with increasing temperature and diminishes at the Néel temperature. The training effect and the opening of the loop reveal the existence of the spin-glass-like surface spins.     

Investigations on structural and magnetic properties of cobalt ferrite/silica nanocomposites prepared by the coprecipitation method

Magnetic nanocomposites consisting of cobalt ferrite nanoparticles embedded in silica matrix were prepared by the coprecipitation method using metallic chlorides as precursors for ferrite. Subsequently composites were annealed at 100, 200 and 300 °C for 2 h. The samples were structurally characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The magnetic properties were measured in the temperature range of 10-300 K using vibrating sample magnetometer (VSM). The effects of thermal treatment on structural and magnetic properties of nanocomposites were investigated. When the samples were annealed, CoFe₂O₄ nanocrystallites were observed in the SiO₂ matrix, whose size increases with increase in annealing temperature. The coercivity and saturation magnetization of nanocomposite (annealed at 300 °C for 2 h) are much higher than that of bulk cobalt ferrite. The realization of adjustable particle sizes and controllable magnetic properties makes the applicability of the CoFe₂O₄ nanocomposite more versatile.     

The effect of solution temperature on crystallite size and magnetic properties of Zn substituted Co ferrite nanoparticles

In this work zinc substituted cobalt ferrite nanoparticles (Co_0.5Zn_0.5Fe₂O₄) have been synthesized by the coprecipitation method, using stable ferric, zinc and cobalt salts with sodium hydroxide, at different solution temperatures, from room temperature to 363 K. The cobalt-zinc ferrite crystalline phase, the particle size and the morphology of the resulting nanoparticles were studied by X-ray diffraction and transmission electron microscopy. The average crystallite size of each sample was calculated from the broadening of the most intense peak (3 1 1), using Scherrer's formula and the results show crystallite sizes increased from 6 to 8 nm by increasing the solution temperature from room temperature to 363 K respectively. Room temperature VSM measurements show that the prepared nanoparticles have superparamagnetic behavior and did not saturate at maximum field of 800 kA/m. The variation of AC-susceptibility of the samples with respect to temperature was measured and it was found that the blocking temperature increased from 198 to 270 K by increasing the solution temperature from room temperature to 363 K respectively. FTIR spectra of the samples have been analyzed in the frequency range 400-4000 cm⁻¹, which also confirms the results of XRD.     

Exchange coupling in CoO–Co bilayer

In this work, exchange bias and coercivity enhancement in ferromagnet (FM)–antiferromagnet (AFM) bilayer have been investigated. CoO film (50 nm) was deposited by sputtering with a relatively high oxygen partial pressure. The deposited films were subsequently annealed at varied temperature up to 973 K in the air atmosphere. The CoO film shows a disordered structure in the as-deposited state and an increase of crystallinity after annealing characterized by XRD and Raman spectra. A 40-nm Co film was deposited on the as-deposited CoO and annealed films. The Co–CoO bilayer shows a large exchange bias up to 1600 Oe and relatively high coercivity up to 3200 Oe (H_C−) at 5 K, which is much larger than that of crystalline Co–CoO bilayer films without any treatment. The spin glass behavior combined with increasing crystallinity, surface roughness of CoO after annealing may be attributed to the large exchange bias and high coercivity.     

Morphology and magnetic properties of Co0.8Fe2.2O4 films prepared by the chemical solution deposition

Co_0.8Fe_2.2O₄ ferrite thin films have been prepared on Si(0 0 1) substrates by the chemical solution deposition. Structural characteristics indicate all films are single phase with spinel structure and the space group and the mean grain size increases from 8 to 30 nm with the increase of annealing temperature. The magnetic properties of Co_0.8Fe_2.2O₄ thin films are highly dependent on annealing temperature. The sample annealed at 800 °C possesses high saturation magnetization, moderate coercivity and squareness ratio, making it a promising application candidate in high-density record and magneto-optical materials.     

Coercivity and squareness enhancement in ball-milled FeCo–MnO nanocomposites

FeCo–MnO nanocomposites were prepared by ball milling mixtures of Fe, Co and Mn, where MnO was obtained from the oxidation of Mn after or during the milling process. The coercivity and squareness of FeCo–MnO nanocomposites increase with increasing milling time. After annealing treatment, the coercivity and squareness increase and exhibit a maximum at 120 h milling time. The temperature dependence of the magnetic properties of FeCo–MnO was also studied and there is a distinct boundary at 120 K. The exchange-bias field and the coercivity decrease quickly with increasing temperature from 30 to 120 K. However, there are no shifted hysteresis loops and the coercivity decreases slightly with increasing temperature from 120 K to room temperature. The enhancement of the coercivity and squareness is mainly attributed to the exchange-bias effects and the reduced magnetic interactions between the FeCo particles by the efficient isolation in MnO matrix.     

Temperature dependence of magnetic properties of NiFe2O4 nanoparticles embeded in SiO2 matrix

Spinel ferrite NiFe₂O₄ nanoparticles (?25 nm) in SiO₂ matrix were prepared by sol–gel method. The phase and average crystallite size of the samples were determined by X-ray diffraction method and the particle size distributions were studied by a transmission electron microscope. Magnetic properties of the samples were investigated with different ferrite particle sizes and at various temperatures down to 10 K. Superparamagnetic properties were observed at room temperature when the particle size is less than 10 nm.In superparamagnetic state, the field dependence of magnetization follows Langevin function which was originally developed for paramagnetism. The effective anisotropy constant K_eff is found to increase significantly with the decrease in particle volume and an order of magnitude higher than that of the bulk samples when the particle size is below 5 nm due to the dominance of surface anisotropy. In case of nanosized systems, the effect of size reduction on the law of approach to saturation has also been studied in detail.     

Preference orientation and magnetic properties of CoxFe3−xO4 nanocrystalline thin films on quartz substrate

Nanocrystalline spinel ferrite thin films of Co_xFe_3−xO₄ (x=0.3$x=0.3$, 0.5, 0.8, and 1.0) have been prepared by RF sputtering on quartz substrate without a buffer layer at room temperature and annealed at the temperature range from 200 to 600 °C in air. The as-sputtered films exhibit the preferred orientation and the high magnetization and coercivity. After annealing, the preferred orientations become poor, but the magnetization and coercivity increase. The sample with a magnetization of 455 emu/cm³, a coercivity of 2.8 kOe, a remanence ratio of 0.72, and a maximum energy product of 2.4 MGOe has been obtained. The influence of Co ions and annealing temperature on the magnetic properties has been discussed.     

Hydrothermal synthesis and magnetic properties of gadolinium-doped CoFe2O4 nanoparticles

CoFe_2−xGd_xO₄ (x=0-0.25) nanoparticles were synthesized via a simple hydrothermal process at 200 °C for 16 h without the assistance of surfactant. The as-synthesized powders were characterized by X-ray diffraction, transmission electron microscopy, and a vibrating sample magnetometer. The X-ray diffraction results showed that the as-synthesized powders were in the pure phase with a doping amount of ≤0.25, and the peaks could be readily indexed to the cubic spinel cobalt ferrite. Transmission electron microscopy and high resolution transmission electron microscopy observations revealed that the gadolinium-doped cobalt ferrite nanoparticles were single crystal, roughly spherical, uniformly distributed, and not highly agglomerated. The room temperature magnetic field versus magnetization measurements confirmed a strong influence of gadolinium doping on the saturation magnetization and coercivity due to large lattice distortion and grain growth of small particles.     

Ferromagnetic resonance observation of a phase transition in magnetic field-aligned Fe2O3 nanoparticles

Fe₂O₃ hematite (alpha) nanoparticles suspended in the liquid phase of the liquid crystal 4,4-azoxyanlsole (PAA) are cooled below the freezing temperature (397 K) in a 4000 G dc magnetic field. The in field solidification locks the direction of maximum magnetization of the particles parallel to the direction of the applied dc magnetic field removing the effects of dynamical fluctuations of the nanoparticles on the magnetic properties allowing a study of the intrinsic magnetic properties of the nanoparticles as well as the anisotropic behavior of the ferromagnetic resonance (FMR) signal. Freezing in PAA allows temperature-dependent measurements to be made at much higher temperature than previous measurements. The field position, line width and intensity of the FMR signal as a function of temperature as well as the magnetization show anomalies in the vicinity of 200 K indicative of a magnetic transition, likely the previously observed Morin transition shifted to lower temperature due to the small particle size. Weak ferromagnetism is observed below T_c in contrast to the bulk material where it is antiferromagnetic below T_c. The Raman spectrum above and below 200 K shows no evidence of a change in lattice symmetry associated with the magnetic transition.     

Synthesis and magnetic characterization of Zn0.6Ni0.4Fe2O4 nanoparticles via a polyethylene glycol-assisted hydrothermal route

Zn-doped nickel ferrite nanoparticles (Zn_0.6Ni_0.4Fe₂O₄) have been prepared via a surfactant, polyethylene glycol assisted hydrothermal route. X-ray powder diffractometry (XRD), Fourier transform infrared spectroscopy, transmission electron microscopy (TEM), and vibrating scanning magnetometry (VSM) were used for the structural, morphological, and magnetic characterizations of the product, respectively. TEM analysis revealed that the nanoparticles have a narrow size distribution, with average particle size of 15±1 nm, which agrees well with the XRD based estimate of 14±2 nm. The absence of saturation and remanent magnetization, and coercivity in the high temperature region of the M-H curve and non-zero magnetic moments indicate superparamagnetism of the nanoparticles with a canted spin structure. The appearance of a peak on the temperature-dependent zero-field cooling magnetization curve at ∼190 K indicates the blocking temperature of the sample.     

Monolayer deposition of L10 FePt nanoparticles via electrospray route

The deposition monolayers of L1₀ FePt nanoparticles via an electrospraying method and the magnetic properties of the deposited film were studied. FePt nanoparticles in a size of around 2.5 nm in diameter, prepared by a liquid process, were used as a precursor. The size of the deposited particles can be controlled up to 35 nm by controlling the sprayed droplet size that is formed by adjusting the precursor concentration and the precursor flow rate. The droplets were heated in a tubular furnace at a temperature of up to 900 °C to remove all organic compounds and to transform the FePt particles from disordered face centered cubic to an ordered FCT phase. Finally, the particles were deposited in the form of a monolayer film on a silicon substrate by electrostatic force and characterized by scanning electron microscopy. The monolayer of particles was obtained by the high charge on particles obtained during the electrospraying process. The magnetic properties of the monolayer were investigated by magneto-optic Kerr effect measurements. Coercivity up to 650 Oe for a film consisting of 35 nm L1₀ FePt nanoparticles was observed after heat treatment at a temperature of 800 °C.