Magnetic behavior of nanocrystalline CoFe2O4

Magnetic nanoparticles of CoFe₂O₄ have been synthesized under an applied magnetic field through a co-precipitation method followed by thermal treatments at different temperatures, producing nanoparticles of varying size. The magnetic behavior of these nanoparticles was investigated. As-grown nanoparticles demonstrate superparamagnetism above the blocking temperature, which is dependent on the particle size. One of the nanoparticles demonstrated a constricted magnetic hysteresis loop with no or small coercivity and remanence at low magnetic field. However, the loop opens up at high magnetic field. This magnetic behavior is attributed to the preferred Co ions and vacancies arrangements when the CoFe₂O₄ nanoparticles were synthesized under an applied magnetic field. Furthermore, this magnetic property is strongly dependent on the high temperature heat treatments that produce Co ions and vacancies disorder.     

Magnetic properties of RE0.7Ca0.3Mn0.95Fe0.05O3 (RE=Sm and Gd) manganites at low temperature

The magnetic properties of RE_0.7Ca_0.3Mn_0.95Fe_0.05O₃ perovskite with rare-earth cations (RE=Sm and Gd) were investigated by means of X-ray diffraction, Mössbauer spectroscopy, and low temperature (4.2-266 K) magnetization measurements. Structural characterization of these compounds shows that they both have orthorhombic (Pbnm) structure. The Mössbauer spectra show clear evidence of local structural distortion of the Mn(Fe)O₆ octahedron, which is based on the non-zero nuclear quadrupole interactions for high-spin Fe³⁺ ions. It was found that the local structural distortion increases significantly when Sm³⁺ is replaced by Gd³⁺. This distortion is attributed to the Jahn-Teller coupling strength as estimated from the Mössbauer effect results. The magnetic results indicate that the Curie temperature decreases as a result of replacing Sm by Gd. This is due to the decrease of the average A-site cationic radius 〈r_A〉. The rapid increase of magnetization at low temperature indicates the magnetic ordering of rare earth ions at the A-site.     

Magnetic and dielectric properties of Ni0.8Co0.1Cu0.1Fe2O4+PZT composites

Magnetoelectric composites of Ni_0.8Co_0.1Cu_0.1Fe₂O₄ and Lead Zirconate Titanate (PZT) were prepared by using conventional ceramic method. The measured values of saturation magnetization (M_s) and magnetic moments (μ_B) are in accordance with the volume fraction of ferrite content in the composite. The dielectric constant of the composites decreases with frequency. The plots of dielectric constant () against temperature (T) show a peak at their respective transition temperatures. The ME output was measured by varying dc bias magnetic field. A large ME output signal of 776 mV/cm was observed for 35% ferrite +65% ferroelectric composite. The magnetoelectric (ME) response is found to be dependent on the content of ferrite phase.     

Magnetic study of Mg0.95Mn0.05Fe2O4 ferrite nanoparticles

The magnetic properties of Mg_0.95Mn_0.05Fe₂O₄ ferrite samples with an average particle size of ∼6.0±0.6 nm have been studied using X-ray diffraction, Mössbauer spectroscopy, dc magnetization and frequency dependent real χ^′(T) and imaginary χ^″(T) parts of ac susceptibility measurements. A magnetic transition to an ordered state is observed at about 195 K from Mössbauer measurements. The zero-field-cooled (ZFC) and field-cooled (FC) magnetization have been recorded at low field and show the typical behavior of a small particle system. The ZFC curve displays a broad maximum at , a temperature which depends upon the distribution of particle volumes in the sample. The FC curve was nearly flat below , as compared with monotonically increasing characteristics of non-interacting superparamagnetic systems indicating the existence of strong interactions among the nanoparticles. A frequency-dependent peak observed in χ^′(T) is well described by Vogel-Fulcher law, yielding a relaxation time and an interaction parameter . Such values show the strong interactions and rule out the possibility of spin-glass (SG) features among the nanoparticle system. On the other hand fitting with the Néel-Brown model and the power law yields an unphysical large value of τ₀ (∼6×10⁻⁶⁹ and 1.2×10⁻²² s respectively).     

Ac magnetotransport in La0.7Sr0.3Mn0.95Fe0.05O3 at low dc magnetic fields

We report the ac electrical response of La_0.7Sr_0.3Mn_1−xFe_xO₃(x=0.05) as a function of temperature, magnetic field (H) and frequency of radio frequency (rf) current (). The ac impedance (Z) was measured while rf current directly passes through the sample as well as in a coil surrounding the sample. It is found that with increasing frequency of the rf current, Z(T) shows an abrupt increase accompanied by a peak at the ferromagnetic Curie temperature. The peak decreases in magnitude and shifts down with increasing value of H. We find a magnetoimpedance of for at around room temperature when the rf current flows directly through the sample and when the rf current flows through a coil surrounding the sample. It is suggested that the magnetoimpedance observed is a consequence of suppression of transverse permeability which enhances skin depth for current flow. Our results indicate that the magnetic field control of high frequency impedance of manganites is more useful than direct current magnetoresistance for low-field applications.     

Synthesis and magnetic properties of hard/soft SrFe12O19/Ni0.7Zn0.3Fe2O4 nanocomposite magnets

Magnetic nanocomposite SrFe₁₂O₁₉/Ni_0.7Zn_0.3Fe₂O₄ powders with different weight fractions of the Ni_0.7Zn_0.3Fe₂O₄ soft ferrite were synthesized by a combination of the sol–gel self-propagation and glyoxilate precursor methods. The results of magnetic measurements revealed the higher Mr/Ms ratio for the nanocomposites than that for the single phase SrFe₁₂O₁₉ which proves the existence of the intergrain exchange coupling between hard and soft magnetic phases with the exchange spring behavior. The highest Mr/Ms ratio of 0.63 was obtained in the composite consisting of 80 wt% of SrFe₁₂O₁₉ and 20 wt% Ni_0.7Zn_0.3Fe₂O₄. The microstructural studies of this sample exhibited the average dimensions of hard and soft phases about 20 nm and 15 nm, respectively which are small enough for strong exchange coupling according to the theoretical studies. The variations of the reduced remanence (Mr/Ms) with increasing the weight fraction of the soft phase could be also explained by the role of the exchange and dipolar interactions in tuning the magnetic properties of the nanocomposites.     

Synthesis of nanocrystalline Zn0.5Mn0.5Fe2O4 via in situ polymerization technique

Nanocrystalline Zn_0.5Mn_0.5Fe₂O₄ was synthesized through the pyrolysis of polyacrylate salt precursors prepared via in situ polymerization of the metal salts and acrylic acid. The pyrolysis behavior of the polymeric precursors was studied by use of thermal analysis. The as-obtained product was characterized by powder X-ray diffraction (XRD), transmission electron microscope (TEM), electron diffraction (ED) pattern, scanning electron microscopy (SEM) and electron dispersive X-ray (EDX) analysis. The results revealed that the particle size is in the range of 15–25 nm for Zn-Mn ferrites with good crystallinity. Magnetic properties of the sample at 300 K were measured using a vibrating sample magnetometer, which showed that the sample exhibited characteristics of superparamagnetism.     

Effect of Ni doping on structural and magnetic properties of Co1-xNixFe1.9Mn0.1O4

Nickel-substituted iron-deficient cobalt ferrite containing small quantity of manganese having the chemical composition Co_1−xNi_xFe_1.9Mn_0.1O₄ with x=0.2, 0.4, 0.6 and 0.8, were prepared by the standard double sintering ceramic technique. The thermal decomposition process of the powder (i.e. grounded starting materials) was studied by thermo-gravimetric analysis (TGA). The compositional analysis was carried out by EDAX pattern. The infrared spectroscopy studies show the presence of tetrahedral and octahedral group complexes within the spinel phase. Microstructural features were studied by scanning electron microscopy, grain size found to be decreasing with increasing Ni content. Room temperature hysteresis measurement was carried out under the field of 6 kOe for all samples which reveal monotonic decrease of magnetization at 6 kOe (M_6 kOe). The coercive field (H_c) decreases up to concentration of Ni²⁺ (x=0.6) and a small increase was observed for x=0.8. Initial permeability (μ_i) plotted against temperature at 10 kHz shown sharp drop at Curie temperature and values observed at transition are found to be dependent on the nickel content.     

Magnetic properties of CoFe1.9RE0.1O4 nanoparticles (RE=La,Ce, Nd,Sm, Eu,Gd, Tb,Ho) prepared in polyol

Highly crystalline CoFe_1.9RE_0.1O₄ ferrite nanoparticles, where RE=La, Ce, Nd, Sm, Eu, Gd, Tb, and Ho, have been synthesized by forced hydrolysis in polyol. X-ray diffraction (XRD), transmission electron microscopy (TEM), electron energy-loss spectroscopy (EELS), ⁵⁷Fe Mössbauer spectrometry, Co K-edge X-ray absorption spectroscopy and magnetic measurements using a SQUID magnetometer were employed to investigate the effect of the substitution RE³⁺ ions for Fe³⁺ ones on the structure, the microstructure, the chemical homogeneity, and the magnetic properties of the cobalt ferrite system. All the produced particles are superparamagnetic at room temperature. Nevertheless, the substitution causes reduction of the blocking temperature which is mainly ascribed to partial cation exchange among the spinel-like sublattices of CoFe₂O₄ induced by the insertion of the relatively large RE³⁺ ions. The low-temperature saturation magnetization and coercivity appear to be greatly affected by the nature of RE³⁺ ions—maxima values were found for Gd³⁺ and Eu³⁺, respectively.     

Preparation and magnetic properties of BaFe12O19/Ni0.8Zn0.2Fe2O4 nanocomposite ferrite

Nanocomposite of hard (BaFe₁₂O₁₉)/soft ferrite (Ni_0.8Zn_0.2Fe₂O₄) have been prepared by the sol–gel process. The nanocomposite ferrite are formed when the calcining temperature is above 800 °C. It is found that the magnetic properties strongly depend on the presintering treatment and calcining temperature. The “bee waist” type hysteresis loops for samples disappear when the presintering temperature is 400 °C and the calcination temperature reaches 1100 °C owing to the exchange-coupling interaction. The remanence of BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite with the mass ratio of 5:1 is higher than a single phase ferrite. The specific saturation magnetization, remanence magnetization and coercivity are 63 emu/g, 36 emu/g and 2750 G, respectively. The exchange-coupling interaction in the BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite is discussed.     

Microwave sintering of high-permeability (Ni0.20Zn0.60Cu0.20)Fe1.98O4 ferrite at low sintering temperatures

The (Ni_0.20Zn_0.60Cu_0.20)Fe_1.98O₄ ferrite was sintered using microwave sintering and conventional sintering technique, respectively. It was found that microwave sintering technique can effectively promote the forward diffusion of ions and thus accelerate the sintering process, resulting in the grain growth and the densification of matrix. At the low frequency of 100 kHz, the magnetizing contribution of domain wall motion is predominant, and compact and coarse matrixes are favorable for domain wall motion, giving rise to improvement of relative initial permeability and loss of ferrites. Using microwave sintering technique, for the (Ni_0.20Zn_0.60Cu_0.20)Fe_1.98O₄ ferrite, the relative initial permeability μ_i of about 2000 and the relative loss factor tanδ/μ_i of about 8.7×10⁻⁶ at 100 kHz were achieved at only 980 °C sintering temperature. In addition, the sintering time of ferrites was reduced from 5 to 0.5 h by using microwave sintering technique.     

Structural and magnetic properties of MnxCo1−xFe2O4 ferrite nanoparticles

We report on the structural and magnetic properties of nanoparticles of Mn_xCo_1−xFe₂O₄ (x=0.1, 0.5) ferrites produced by the glycothermal reaction. From the analysis of XRD spectra and TEM micrographs, particle sizes of the samples have been found to be about 8 nm (for x=0.1) and 13 nm (for x=0.5). The samples were characterized by DC magnetization in the temperature range 5-380 K and in magnetic fields of up to 40 kOe using a SQUID magnetometer. Mössbauer spectroscopy results show that the sample with higher Mn content has enhanced hyperfine fields after thermal annealing at 700 °C. There is a corresponding small reduction in hyperfine fields for the sample with lower Mn content. The variations of saturation magnetization, remnant magnetization and coercive fields as functions of temperature are also presented. Our results show evidence of superparamagnetic behaviour associated with the nanosized particles. Particle sizes appear to be critical in explaining the observed properties.     

Magnetotransport and magnetoelastic effects in Co-doped La0.7Sr0.3MnO3 nanocrystalline perovskites

La_0.7Sr_0.3Mn_1−xCo_xO₃ (x=0, 0.05, 0.1) nanoparticles, prepared by sol-gel method, were studied by means of X-ray diffraction, transmission electron microscopy, resistivity, magnetoresistance, thermal expansion and magnetostriction measurements. Results show that partial substitution of Mn by Co leads to a reduction in lattice parameters, enhancement of resistivity and room temperature magnetoresistance MR, decrease of metal-insulator transition temperature T_MI and T_C, an increase in thermal expansion coefficient, volume magnetostriction and anisotropic magnetostriction. The latter increases about one order of magnitude with 10% Co substitution. In comparison with Mn ions, the Co ions possess higher anisotropy energy, larger magnetostriction effect, smaller ionic size and spin state transitions with increase in temperature and magnetic field; this suggests that Co substitution leads to double-exchange interaction weakening, resulting in suppression of ferromagnetic long-range order and metallic state and increase of magnetic anisotropy. Furthermore, our samples have a relatively lower T_MI and T_C, higher resistivity and MR, compared with the reported values for similar compounds with larger particle sizes. This is attributed to the nanometric grain size and spin-polarized tunneling between neighboring grains.     

多晶La0.7Sr0.3MnO3的低温输运性质和磁电阻效应

详细研究了由纳米晶粒组成的块体多晶La_0.7Sr_0.3MnO₃(LSM)的电阻率和磁电阻效应,以及它们的温度依赖性.随着温度从室温降低,电阻率(ρ)在250K附近存在一最大值,低于该温度后,样品表现为金属导电特性,随后在50K附近存在一极小值.也就是说在低于50K的温度范围内,随着温度降低ρ反而升高,表现为绝缘体性的导电特性.经研究发现,这种随温度降低ρ反而增加的现象与隧穿效应的理论模型(lnρ∝T^-1/2)符合得很好 关键词： 0.7Sr_0.3MnO₃')" href="#">多晶La_0.7Sr_0.3MnO₃ 隧道效应 隧道磁电阻效应     

X-ray Debye temperature of mechanically milled Ni0.5Zn0.5Fe2O4 spinel ferrite

The X-ray Debye temperatures, θ _M , of spinel ferrite composition Ni_0.5Zn_0.5Fe₂O₄, mechanically milled upto 9 hrs, were determined from integrated intensities of selected Bragg reflections. The θ _M was found to increase with milling time. The results are explained in the light of milling induced grain orientation and surface effect. The values of θ _M were found to be lower as compared to the Debye temperatures obtained from infrared spectral data analysis. The difference can be explained on the basis of increase in an excess free volume in the form of vacancies and vacancy clusters associated with grain boundaries.     

The effect of B2O3 addition to the microstructure and magnetic properties of Ni0.4Zn0.6Fe2O4 ferrite

The effects of 0.01 and 0.1 mol B₂O₃ addition to the microstructure and magnetic properties of a Ni–Zn ferrite composition expressed by a molecular formula of Ni_0.4Zn_0.6Fe₂O₄ were investigated. The toroid-shaped samples prepared by pressing the milled raw materials used in the preparation of the composition were sintered in the range of 1000–1300 °C. The addition of 0.01 mol B₂O₃ increased the grain growth and densification giving rise to reduced intergranular and intragranular porosity due to liquid-phase sintering. The sintered toroid sample at 1300 °C gave the optimum magnetic properties of B_r=170 mT, H_c=0.025 kA/m and a high initial permeability value of μ_i=4000. The increment of the B₂O₃ content to 0.1 mol resulted in a pronounced grain growth and also gave rise to large porosity due to the evaporation of B₂O₃ at higher sintering temperatures. Hence, it resulted in an air-gap effect in the hysteresis curves of these samples.     

Magnetic pair making and breaking effect of Ru in La0.7Sr0.3Mn0.9Ru0.1O3 and La0.5Sr0.5Co0.9Ru0.1O3

The substitutional effect of Ru on the magnetic and transport properties of double exchange ferromagnets, La_0.7Sr_0.3MnO₃ and La_0.5Sr_0.5CoO₃ has been investigated. It is found that substitution of 10% Ru at the Mn site of La_0.7Sr_0.3MnO₃ decreases the Curie temperature by 20 K than that of the parent compound. However, a large decrease in the Curie temperature, ΔT_c80 K and the system undergoes a transition from metallic state to insulating state is observed when 10% Ru is doped in La_0.5Sr_0.5CoO₃. The marginal effect of Ru in the Mn–O–Mn sublattice in comparison to the Co–O–Co sublattice could be due to the magnetic exchange interaction between Mn and Ru by virtue of the fact that Ru exhibits variable valence states, Ru⁺⁴/Ru⁺⁵. The e_g and t_2g parentage of Ru⁺⁵ is similar to Mn⁺⁴ and therefore, Ru⁺⁵ ion appears to participate in the double exchange mediated ferromagnetic (FM) interaction. On the other hand, Ruthenium (IV) ion disrupts an intermediate spin state of cobalt (Co⁺³: t_2g⁵e_g¹), forcing a double exchange FM state to anti-FM state.     

Enhancement of the magnetostrictive properties of Co0.9Mn0.1Fe2O4 synthesized by using the precursor preparation technique

Co_1−xMn_xFe₂O₄ has been prepared by calcining hydrotalcite-like precursors for the first time. The crystallization behaviors and magnetoelastic properties of the samples have been investigated. The experimental results show that precursor preparation technique is superior compared to the traditional ceramic method. By adopting hydrotalcite-like precursor preparation technique, a fine and more uniform microstructure can be developed. An obvious enhancement of magnetostriction from 95 to 122 ppm and saturation magnetization from 66 to 78 emu/g has been obtained in Co_0.9Mn_0.1Fe₂O₄ composite under lower magnetic filed. This is propitious to apply to sensors and actuators.