Microwave properties of composites with glass coated amorphous magnetic microwires

The complex permittivity and permeability of composites filled with Fe-based microwires are measured in a coaxial line at frequencies from 0.01 to 10 GHz.The samples under study consist of closely packed wire sections with various orientations relative to wave vector. The composites, where the wires are collinear to the coaxial axis, are found to be low permeable. Their permittivity has frequency dispersion governed by the length of the wire and its linear impedance. The middle section of the wire has higher impedance than that of the end sections where the regular domain structure is distorted. Magnetic bias parallel to the wire axis affects the linear impedance and parameters of dielectric absorption of a composite, the effect is proportional to bias strength. The samples of a coil-type structure, where the wires are wound around the coaxial axis, display the intensive magnetic absorption attributed to the domain wall motion. The absorption takes place in the megahertz band, at microwaves the permeability is close to unity. The microwave properties of diluted composites filled with randomly oriented permeable wires are discussed.     

Coil-less fluxgate effect in (Co0.94Fe0.06)72.5Si12.5B15 amorphous wires

In this study, the coil-less fluxgate properties of the as-cast and annealed amorphous wires with the composition (Co_0.94Fe_0.06)_72.5Si_12.5B₁₅ were investigated. As its name implies, a coil-less fluxgate is a new type of magnetic-field sensor without a coil. When the wire is periodically saturated in a magnetic field in the circumferential direction with a 30 kHz, 62 mA driving current under a 16.5π rad/m torsional strain, there is a linear variation in the second harmonic of the voltage from the wire ends as a function of the applied external DC magnetic field along the length of the wire.Current-stress annealing of each sample improved the sensitivity of the coil-less fluxgate sensor. This is the first time that it has been shown that a linear change in the output of the coil-less fluxgate sensor can be obtained using torsion annealed wire without the necessity of twisting the wire during measurement. We showed that the linear operating range of the sensor can be increased by increasing the demagnetization factor in the sensing direction, so that the coil-less fluxgate sensor can be miniaturised just by reducing the wire length.     

Magnetic properties and magneto electric effect in ferroelectric rich Ni0.5Zn0.5Fe2O4+BPZT ME composites

Magneto electric composites with composition (x) Ni_0.5Zn_0.5Fe₂O₄+(1-x) Ba_0.8Pb_0.2Zr_0.8Ti_0.2O₃ (BPZT—barium lead zirconate titanate) in which x varies as 0.0, 0.15, 0.30, 0.45 and 1.0 mol% were prepared by standard double sintering ceramic method. The presence of constituent phases such as ferrite and ferroelectric was confirmed by X-ray diffraction. The structural analyses were carried out by using X-ray diffraction pattern. Scanning electron micrographs (SEM) were taken to understand the microstructure of the samples. The calculated values of the porosity of the samples lie between 4.5% and 16.2%. The hysteresis measurements were made to determine saturation magnetization (M_s), magnetic moment (μ_B) and coercivity (H_c). From the AC susceptibility measurements the contribution of both the single domain (SD) particles of the ferrite phase and mixed domain (SD+MD) particles of the composites in ME output were explained. The static magneto electric voltage coefficients (dE/dH)_H were measured as a function of intensity of magnetic field and the maximum ME coefficient were observed for the composites with 30% of ferrite+70% of ferroelectric phase.     

Mössbauer studies on the superparamagnetic behavior of CoFe2O4 with a few nanometers

CoFe₂O₄ nanoparticles with a cubic spinel structure are prepared by a high-temperature thermal decomposition method. The average particle sizes are 4.6  and 5.7 nm for CoFe₂O₄ made with two kinds of solvents by TEM. Mössbauer spectra of 4.6 nm particles displayed a superparamagnetic behavior as demonstrated by a single line with zero hyperfine fields, but that of 5.7 nm particles did not at room temperature. It is considered that anisotropy energy was still more superior to thermal energy because of particle size of 5.7 nm CoFe₂O₄. Furthermore, Mössbauer spectra exhibited the typical spectrum shapes of the CoFe₂O₄ at 4.2 K. The spectrum at 4.2 K was fitted using two magnetic components of hyperfine fields _Hhf=540.4,512.6$H_{\mathrm{hf}}=540.4,512.6$ kOe and isomer shifts δ=0.40,0.30$\delta =0.40,0.30$ mm/s for 4.6 nm and _Hhf=542.7,512.8$H_{\mathrm{hf}}=542.7,512.8$ kOe and δ=0.41,0.29$\delta =0.41,0.29$ mm/s for 5.7 nm corresponding to Fe³⁺ ions at site A and site B, respectively.     

Morphology and magnetic properties of Co0.8Fe2.2O4 films prepared by the chemical solution deposition

Co_0.8Fe_2.2O₄ ferrite thin films have been prepared on Si(0 0 1) substrates by the chemical solution deposition. Structural characteristics indicate all films are single phase with spinel structure and the space group and the mean grain size increases from 8 to 30 nm with the increase of annealing temperature. The magnetic properties of Co_0.8Fe_2.2O₄ thin films are highly dependent on annealing temperature. The sample annealed at 800 °C possesses high saturation magnetization, moderate coercivity and squareness ratio, making it a promising application candidate in high-density record and magneto-optical materials.     

Multiferroic properties of Bi0.8La0.2FeO3/CoFe2O4 multilayer thin films

Bi_0.8La_0.2FeO₃/CoFe₂O₄ (BLFO/CFO) multilayer thin films (totally 20 layers BLFO and 19 layers CFO) were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and transmission electron microscope measurements show that the films are polycrystalline and consisted of multilayered structure. Ferroelectric hysteresis loops with remnant polarization and saturated polarization of 4.2 and 13.3 μC/cm², respectively, were observed. On the other hand, the films show well-shaped magnetization hysteresis loops with saturated and remnant magnetization of 34.7 and 11.4 emu/cm³, respectively, which are significantly larger than pure BLFO thin films deposited under the same conditions. These results indicate that constructing epitaxial superlattice might be a promising way to fabricate multiferroics with improved properties.     

Eu and Fe Mössbauer study of mechanically alloyed EuFeO3

EuFeO₃ was prepared by mechanical alloying starting from europium and iron oxides. After 20 h of milling the resulting compound is pure EuFeO₃. Samples were studied as a function of milling period using XRD, Mössbauer, SEM, and magnetic measurements. Mössbauer spectroscopy was used to probe both the transition metal and the rare-earth sites. Results are compared with previous works on EuFeO₃ prepared by different methods.     

Mössbauer spectroscopy as a probe of magnetic states in La0.5Ca0.5FeO3−δ perovskite

Charge disproportionation in La_0.5Ca_0.5FeO_3−δ perovskite has been detected by zero-field Mössbauer spectra from 20 K to room temperature. On the basis of the parameters of center shifts and hyperfine fields, Mössbauer spectra identified that the iron ionic states are Fe³⁺ and Fe⁵⁺ below 150 K, Fe³⁺, Fe⁴⁺ and Fe⁵⁺ in the intermediate temperature region, as well as Fe³⁺ and Fe⁴⁺ above 220 K. At low temperatures, the system exhibits a cluster-glass-like state resulting from competition between antiferromagnetic interaction of Fe³⁺–Fe³⁺ and ferromagnetic interaction of Fe³⁺–Fe⁵⁺.     

Mössbauer study of antiferromagnetic CuFeO2

We have studied the magnetic spin structure of antiferromagnetic CuFeO₂ by X-ray diffraction (XRD) and Mössbauer spectroscopy. Its crystal structure determined by XRD analysis was a rhombohedral structure (space group R-3m) and lattice constants a₀ and c₀ were 3.0333 and 17.1595 Å, respectively. In spite of 4-Fe sublattices in a delafossite CuFeO₂, its Mössbauer spectra were analyzed with 1-set (6-Lorentzian lines) below 10 K due to the collinear-commensurate spin structure, but the spectra were fitted with 4-sextet above 10 K due to the incommensurate spin structure. This phenomenon was attributed to the spin–lattice relaxation effect. Magnetic Néel temperature was also determined at 18 K, which corresponded to the high-spin Fe³⁺ valance state. On the other hand, CuFe_0.98Al_0.02O₂ powder with a noncollinear spin structure was fitted with 4-sextet at 4.2 K.     

X-ray diffraction,microstructure, Mössbauer and magnetization studies of nanostructured Fe50Ni50 alloy prepared by mechanical alloying

Nanocrystalline Fe₅₀Ni₅₀ alloy samples were prepared by the mechanical alloying process using planetary high-energy ball mill. The alloy formation and different physical properties were investigated as a function of milling time, t, (in the 0–50 h range) by means of the X-ray diffraction (XRD) technique, scanning electron microscopy (SEM), energy dispersive X-ray (EDAX), Mössbauer spectroscopy and the vibrating sample magnetometer (VSM). The complete formation of γ-FeNi is observed after 24 h milling. When milling time increases from 0 to 50 h, the lattice parameter increases towards the Fe₅₀Ni₅₀ bulk value, the grain size decreases from 67 to 13 nm, while the strain increases from 0.09% to 0.41%. Grain morphologies at different formation stages were observed by SEM. Saturation magnetization and coercive fields derived from the hysteresis curves are discussed as a function of milling time.     

Spin glass ordering of Zn0.75Co0.25Fe0.5Cr1.5O4 cubic spinel

The linear and nonlinear low field AC susceptibilities of Zn_0.75Co_0.25Fe_0.5Cr_1.5O₄ show peaks due to non-critical contributions, which mask the peak due to spin glass ordering. They extend into the region of temperatures in which Mössbauer spectra do not show any magnetic component. When a DC field of 200 Oe suppresses the non-critical contributions, peak due to spin glass ordering is clearly visible. The spin glass ordering is thus shown to be a thermodynamic transition. The critical exponent is found to fall within the range found using other spin glasses. Mössbauer spectra in zero fields provide T_SG, which agrees with the peak temperature of AC susceptibilities in the absence of non-critical contributions. 〈S_Z〉 determined using Mössbauer spectra does not show any anomaly. In the presence of a field of 5 T, the spectra show SG ordering at 4.2 K, which converts into ferrimagnetic ordering at higher temperatures.     

Mössbauer characterization of tin dopant ions in the antiferromagnetic ilmenite MnTiO3

Mössbauer parameters of ¹¹⁹Sn diamagnetic dopant cations in an antiferromagnetic compound having the ilmenite structure are for the first time reported. The spectra reveal a well resolved hyperfine splitting pattern of combined magnetic and quadrupole interactions (at 5 K, δ=0.19 mm/s, H₁=52.5 kOe, eV_ZZQ_3/2=−0.80 mm/s, θ≈0°). This spectral component whose contribution (A₁=82%) represents more than four fifths of the total amount of the dopant (Sn/(Mn+Ti)=1/200) is assigned to Sn(IV) ions located in the bulk of MnTiO₃, on the Mn(II) site, and with a Mn(II) vacancy in their nearest surrounding. Two spectral components with minor contributions are also observed: one of them (H₂≈25 kOe, A₂=8%) can be assigned to Sn(IV) ions, in the MnTiO₃ lattice as well, on a site where they exhibit a weaker spin polarization (this site could be the Ti(IV) one) and the other (H₃=0 kOe, A₃=10%) to SnO₂ or/and Ti_1−xSn_xO₂ clusters. The Néel temperature of MnTiO₃ probed by the ¹¹⁹Sn dopant (T_N=69±2 K) agrees well with the values previously provided by ESR and antiferromagnetic resonance measurements. Variation of H₁ with temperature follows close the Brillouin function for S=5/2. No perturbation appears in the Mössbauer spectra around T=90 K where a broad peak, characteristic of 2D magnetic interactions, is observed on the static magnetic susceptibility curve.     

Emission Mössbauer studies of the magnetoresistive compound, La0.7Sr0.3MnO3

The magnetic behavior of the Sr_0.3 manganite is studied using a local microprobe, ⁵⁷Co. In contrast with Ca substituted manganites, a much larger fraction of the material exhibits short-range order with superparamagnetic-like behavior even at 80 K. The differences in behavior are attributed to the large mismatch between the ionic radii of La⁺³ and the divalent substituent Sr⁺², which introduces anharmonicity in local vibrations. In common with all other compounds exhibiting negative bulk magnetoresistivity, the Sr_0.3 compound also exhibits very marked softening of lattice as one approaches T_c from below. Application of an external magnetic field results in coalescing of nanosized magnetic clusters to form larger ones with better alignment of spins.     

Maxwell-Wagner characterization of dielectric relaxation in Ni0.8Zn0.2Fe2O4/Sr0.5Ba0.5Nb2O6 composite

Dense composites were prepared through incorporating the dispersed Ni_0.8Zn_0.2Fe₂O₄ ferromagnetic particles into Sr_0.5Ba_0.5Nb₂O₆ ferroelectric matrix. Extrinsic dielectric relaxation and associated high permittivities of the materials are reported in the composites. We used an ideal equivalent circuit to explain electrical responses in impedance formalism. A Debye-like relaxation in the permittivity formalism was also found. Interestingly, real permittivity (ε′) of the sample containing 30% Ni_0.8Zn_0.2Fe₂O₄ shows obvious independence of the temperature at 100 kHz. Dielectric relaxation and high-ε′ properties of the composites are explained in terms of the Maxwell-Wagner (MW) polarization model.     

Temperature-dependent Mössbauer and dielectric studies of Mg0.95Mn0.05Fe1.0Ti1.0O4

The effect of tetravalent Ti⁺⁴ substitution in Mg_0.95Mn_0.05Fe₂O₄ on its magnetic and electrical properties has been studied using X-ray diffraction, Mössbauer spectroscopy, isothermal dc magnetization and dielectric measurements. X-ray diffraction studies have shown the structural transformation from cubic to tetragonal with the Ti⁺⁴ substitution. The Mössbauer spectra of Mg_0.95Mn_0.05Fe_1.0Ti_1.0O₄ recorded in the temperature range 20-300 K shows the presence of the magnetic as well as quadrupole interactions. The isothermal hysteresis loop infers that the system exhibits a ferrimagnetic ordering at room temperature. The Zero-field-cooled (ZFC) and field-cooled (FC) magnetization studies support ferrimagnetic ordering of Mg_0.95Mn_0.05Fe_1.0Ti_1.0O₄ at room temperature. Signatures of ferroelectric transition have been observed in the temperature range 200-300 K from dielectric measurements. The observed magnetic and dielectric behaviour indicate that this material exhibits multiferroic behaviour.     

The role of iron in the formation of the magnetic structure and related properties of La0.8Sr0.2Co1−xFexO3 (x=0.15, 0.2, 0.3)

La_0.8Sr_0.2Co_1−xFe_xO₃ (x=0.15, 0.2, 0.3) samples were studied by means of AC magnetic susceptibility, magnetization, magnetoresistance and ⁵⁷Fe Mössbauer spectrometry. Iron was found to take on a high spin 3d^5−α electronic state in each of the samples, where α refers to a partly delocalized 3d electron. The compounds were found to exhibit a spin-cluster glass transition with a common transition temperature of ∼53 K. The spin-cluster glass transition is visualized in the ⁵⁷Fe Mössbauer spectra as the slowing down of magnetic relaxation below ∼70 K, thereby showing that iron takes part in the formation of the glassy magnetic phase. The paramagnetic-like phase found at higher temperatures is identified below T_c≈195 K as being composed of weakly interacting, magnetically ordered nanosized clusters of magnetic ions in part with a magnetic moment oriented opposite to the net magnetic moment of the cluster. For each of the samples a considerable low-temperature negative magnetoresistance was found, whose magnitude in the studied range decreases with increasing iron concentration. The observed results obtained on the present compounds are qualitatively explained assuming that the absolute strengths of magnetic exchange interactions are subject to the relation ∣J_Co–Co∣<∣J_Fe–Co∣<∣J_Fe–Fe∣.     

Effect of dc-Joule-heating thermal processing on magnetoimpedance of Fe72Al5Ga2P11C6B4 amorphous alloy

The effect of multistep dc-Joule-heating thermal processing on magnetoimpedance (MI) of Fe₇₂Al₅Ga₂P₁₁C₆B₄ ribbons is presented. After material optimization significant increase of MI response up to value ΔZ/Z≈55% as well as sensitivity of about 6%/kA/m (for H?3–4 kA/m), were recorded in still amorphous samples at driving frequencies 2–3 MHz. On-line and post-annealing electrical resistivity together with Mössbauer spectra analysis and frequency dependence of the penetration depth were used for characterization of MI improvement.     

Mössbauer study of Fe0.92−xCoxP0.08 nanowire arrays

Arrays of Fe_0.92−xCo_xP_0.08 (0.22≤x≤0.78) ternary alloy nanowires were fabricated in anodic aluminium oxide templates by electrochemical deposition. The broadened peaks in transmission Mössbauer spectra and the halo in selected area electron diffraction patterns indicate that the structure of Fe_0.92−xCo_xP_0.08 nanowires is amorphous. However, the short-range order of Fe_0.92−xCo_xP_0.08 nanowires has a bcc structure with a [110]-preferred orientation that is parallel to the nanowires. The magnetic texture results in the magnetic moment direction of the Fe atoms being along the nanowires. The short-range order around the Fe atoms reaches a minimum at x=0.45. With increasing Co content, the average hyperfine field decreases, while the isomer shift and quadrupole splitting remain almost constant, which result from the variation of 3d and 4s electron volume density at the Fe sites.     

Structure and magnetic properties of (Nd,Dy)16(Fe,Co)76−xTixB8 powders prepared by mechanical alloying

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at % of Ti results in an increase of coercivity from 796 to 1115 kA m⁻¹. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA m⁻¹. Mössbauer investigations shows that for x?1 the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x>1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity decreases due to the presence of an amorphous phase. A heat treatment at a higher temperature (1073 K) for longer time (1 h) results in the full recrystallisation of powders. The mean hyperfine field of the Nd₂Fe₁₄B phase decreases for titanium contents of 0?x?1, and remains constant for x>1. This indicates that the Ti content in the Nd₂Fe₁₄B phase reaches its maximum value.