Effects of Titania on the Adsorptive and Catalytic Properties of Silica-Supported Cobalt Catalyst

A series of Ti-promoted (6 wt%) Co/SiO₂ catalysts with titania content of 0 to 10 wt% were sequentially prepared by incipient wetness impregnation, and characterized with X-ray diffraction, thermogravimetric analysis, chemisorption, temperature-programmed desorption and infrared spectroscopy. The influences of Ti addition and reduction temperature (400–700 °C) on the adsorptive behavior and the catalytic properties for CO hydrogenation were investigated. The presence of Ti decreases the adsorption capacity of the cobalt surface for H₂, but enhances activity per gram cobalt. In addition, the turnover frequency increases 2–4 times upon Ti addition at reduction temperatures of 400–700 °C. The promotion in activity is accompanied by an enhanced selectivity for higher hydrocarbons and olefins. These modifications can be rationalized by the creation of active sites for CO dissociation. The desorption of CO₂ at 100 °C during temperature-programmed desorption of CO indicates the formation of active sites for CO disproportionation. Infrared spectroscopy indicates an increase in the relative absorbance of 2060–2075 cm^?1 bands upon Ti addition, which are attributed to CO adsorbed on the defect sites of the cobalt surface. Therefore, the promotion effect of Ti may be directly related to the formation of defect sites on the cobalt surface induced by the decorated titania moieties.     

Preparation of Titania/PDMS Hybrid Films and the Conversion to Porous Materials

Transparent films of titania/poly(dimethylsiloxane) (PDMS) hybrids were prepared by the solvent evaporation from the precursor solution prepared by the co-hydrolysis and co-condensation of titanium tetraisopropoxide and a methoxy-functionalized PDMS. The hybrid films were flexible and had high homogeneity of the composition. The organic groups of PDMS were decomposed at 400°C in air to form porous films. Though the heated films were rather brittle compared to the as-synthesized films, they were still transparent and homogeneous. The BET surface areas of the films after the heat treatment at 400°C were over 300 m²/g, while the as-synthesized hybrid films were non porous. According to the BDDT classification, the nitrogen adsorption/desorption isotherms of the calcined films were Type I, showing that the films were microporous. The titania domains were still amorphous after the heat treatment at 400°C and transformed to anatase after the heat treatment at 1,000°C.     

A Novel Route to the Synthesis of Mesoporous Titania with Full Anatase Nanocrystalline Domains

A porous, high surface area TiO₂ with anatase or rutile crystalline domains is advantageous for high efficiency photonic devices. Here, we report a new route to the synthesis of mesoporous titania with full anatase crystalline domains. This route involves the preparation of anatase nanocrystalline seed suspensions as the titania precursor and a block copolymer surfactant, Pluronic P123 as the template for the hydrothermal self-assembly process. A large pore (7–8 nm) mesoporous titania with a high surface area of 106–150 m²/g after calcination at 400°C for 4 h in air is achieved. Increasing the hydrothermal temperature decreases the surface area and creates larger pores. Characteristics of the seed precursors as well as the resultant mesoporous titania powder were studied using XRD analysis, N₂-adsorption/desorption analysis, and TEM. We believe these materials will be especially useful for photoelectrochemical solar cell and photocatalysis applications.     

High surface area sol–gel alumina–titania nanocatalyst

Alumina–titania mixed oxide nanocatalysts with molar ratios = 1:0.5, 1:1, 1:2, 1:5 have been synthesized by adopting a hybrid sol–gel route using boehmite sol as the precursor for alumina and titanium isopropoxide as the precursor for titania. The thermal properties, XRD phase analysis, specific surface area, adsorption isotherms and pore size details along with temperature programmed desorption of ammonia are presented. A specific surface area as high as 291 m²/g is observed for 1:5 Al₂O₃/TiO₂ composition calcined at 400 °C, but the same composition when calcined at 1,000 °C, resulted in a surface area of 4 m²/g, while 1:0.5 composition shows a specific surface area of 41 m²/g at 1,000 °C. Temperature programmed desorption (of ammonia) results show more acidic nature for the titania rich mixed oxide compositions. Transmission electron microscopy of low and high titania content samples calcined at 400 °C, shows homogeneous distribution of phases in the nano range. In the mixed oxide, the particle size ranges between 10–20 nm depending on titania content. The detailed porosity data analysis contributes very much in designing alumina–titania mixed oxide nanocatalysts.     

Thermal, spectral, and diffraction properties of Co-exchanged montmorillonite with 2-, 3-, and 4-hydroxyphenol

The influence of the 2-, 3-, and 4-OH phenols on the type of interaction with Co-exchanged montmorillonite and thermal properties of these materials were studied. The results of XRD, IR, and thermal (TG, DTG) analysis show that organic species are intercalated into the interlayer space of montmorillonite. Thermal decomposition in the temperature interval 20?C700?°C of studied samples with 2- and 3-hydroxyphenol proceeds in three steps (the release of adsorbed H₂O molecules, combustion/desorption of protonated hydroxy phenols and dehydroxylation), while the sample with 4-hydroxyphenol decompose in four steps (the new peak at ~222?°C corresponds to directly coordinated organic species). The effect of different position of the hydroxyl groups on the phenol ring on the thermal decomposition is evident.     

Mesoporous Titania Thin Film with Highly Ordered and Fully Accessible Vertical Pores and Crystalline Walls

We report the preparation of mesoporous titania thin films with the R m pore structure derived from the Im m self‐assembled ordering of the titania species and an EO₁₀₆PO₇₀EO₁₀₆ triblock copolymer. The films were spin‐cast and then aged at 18 °C at a relative humidity of 70 %, which led to the orientation of the Im m structure with the [111] direction perpendicular to the substrates. The [111] body‐diagonal channels became vertical channels upon calcination at 400 °C, thus leading to thin films with vertical channels. The pores are ordered over a large area of up to 1 μm². The titania films can be formed on various types of substrates. By using a titania film formed on a Pt‐coated Si wafer as a template, we produced by an electrochemical‐deposition technique arrays of gold nanowires, whose morphology suggests that most of the pores of the titania thin films are accessible. The pore structure of vertical channels is stable up to 600 °C, at which temperature the wall materials crystallize into anatase.     

Physicochemical Characterization and Catalytic Properties of Titania Gel Doped with Lithium and Rubidium

The effect on titania of doping with lithium and rubidium titania gels has been studied in samples prepared with titanium (IV) tetra-n-butoxide co-gelling with the alkaline metal precursors. Titania and doped titania were characterized by X-Ray diffraction, which showed that the catalysts were nanostructured. In samples calcined at 400°C, the crystallite size of the anatase phase was 17 and 14 nm, and 78 and 38 nm for samples calcined at 600°C, for Li/TiO₂ and Rb/TiO₂, respectively. The specific surface areas of doped samples (400°C) are lower in Li/TiO₂ (90 m²/g) than in Rb/TiO₂(125 m²/g). Evaluation of their basic properties has been carried out in the acetone condensation reaction. It was found that the activity strongly depended on the Li and Rb ionic radii.     

A thermogravimetric and infrared emission spectroscopic study of alunite

Thermogravimetric and differential thermogravimetric analysis has been used to characterize alunite of formula [K₂(Al³⁺)₆(SO₄)₄(OH)₁₂]. Thermal decomposition occurs in a series of steps (a) dehydration up to 225°C, (b) well defined dehydroxylation at 520°C and desulphation which takes place as a series of steps at 649, 685 and 744°C.The alunite minerals were further characterized by infrared emission spectroscopy (IES). Well defined hydroxyl stretching bands at around 3463 and 3449 cm^?1 are observed. At 550°C all intensity in these bands is lost in harmony with the thermal analysis results. OH stretching bands give calculated hydrogen bond distances of 2.90 and 2.84–7 Å. These hydrogen bond distances increase with increasing temperature. Characteristic (SO₄)^2? stretching modes are observed at 1029.5, 1086 and 1170 cm^?1. These bands shift to lower wavenumbers on thermal treatment. The intensity in these bands is lost by 550°C.     

Metal-Support interaction in Silica-Supported Cobalt Catalyst

The variations in catalytic properties for CO hydrogenation and adsorptive properties for H₂ and CO of silica-supported cobalt catalyst as a function of reduction temperature (400 to 700 °C) were investigated. A mild sintering of cobalt metal from 130 Å to 145 Å occurred only when the reduction temperature was further increased from 600 to 700 °C. However, a monotone decrease in the activity (per gram Co) for CO hydrogenation was observed with increasing reduction temperature. This is accompanied with a decrease in methane and an increase in olefin formation. The decrease in activity can not be accounted for by the variation of crystallite size of cobalt metal. A concurrent suppression in the amount of hydrogen and CO adsorptions was observed after reduction temperature was raised to 700 °C. The turnover frequencies, based on cobalt dispersion estimated from H₂ and CO chemisorption, remained, more or less, similar with increasing reduction temperature from 400 to 600 °C, but increased ca. 3 and 1.5 times, respectively, at 700 °C. The relative amount of subcarbonyl species (2062 cm^?1) with respect to the linear adsorbed CO (2010 cm^?1) was found to increase as well. Furthermore, reduction of silica surface at 700 °C was indicated by the presence of ?Si-H, which was detected by infrared spectroscopy at 2294 cm^?1. This shows the presence of metal-support interaction for silica-supported cobalt systems after reduction treatment at 700 °C.     

Thermal decomposition of the hydrotalcite

Summary A combination of thermogravimetry and hot stage Raman spectroscopy has been used to study the thermal decomposition of the synthesised zinc substituted takovite Zn₆Al₂CO₃(OH)₁₆·4H₂O. Thermogravimetry reveals seven mass loss steps at 52, 135, 174, 237, 265, 590 and ~780°C. MS shows that the first two mass loss steps are due to dehydration, the next two to dehydroxylation and the mass loss step at 265°C to combined dehydroxylation and decarbonation. The two higher mass loss steps are attributed to decarbonation. Raman spectra of the hydroxyl stretching region over the 25 to 200°C temperature range, enable identification of bands attributed to water stretching vibrations, MOH stretching modes and strongly hydrogen bonded CO₃^2--water bands. CO₃^2- symmetric stretching modes are observed at 1077 and 1060 cm^-1. One possible model is that the band at 1077 cm^-1is ascribed to the CO₃^2- units bonded to one OH unit and the band at 1092 cm^-1is due to the CO₃^2- units bonded to two OH units from the Zn-takovite surface. Thermogravimetric analysis when combined with hot stage Raman spectroscopy forms a very powerful technique for the study of the thermal decomposition of minerals such as hydrotalcites.</o:p>     

Formation and Conversion of Surface Compounds upon Interaction of Ethanol with Cu/CeO<Subscript>2</Subscript> Catalyst According to in situ IR Spectroscopy

In the conditions of ethanol conversion on the surface of a 5%Cu/CeO₂ catalyst, the method of in situ IR spectroscopy reveals ethoxy groups, acetate and formiate complexes, and consolidation products. Acetaldehyde, acetone, croton aldehyde, butadiene, hydrogen, CO, and CO₂ are observed in the reaction products. As the temperature of the experiment increases, the concentration of acetaldehyde passes through a maximum at T = 250°C. This product is formed due to the interaction of ethoxy and hydroxyl surface groups. The concentration of acetone, croton aldehyde, and butadiene also passes through a maximum in the 350–400°C range. These products are associated with the decomposition of the consolidation products. The concentration of hydrogen, CO and CO₂ steadily increases with temperature and only these reaction products are left at T > 400°C. A mechanism of hydrogen formation based on the conversion of the highest temperature formiate surface complex is discussed.     

Thermal decomposition of the composite hydrotalcites of iowaite and woodallite

The thermal stability and thermal decomposition pathways for synthesized composite iowaite/woodallite have been determined using thermogravimetry analysis in conjunction with evolved gas mass spectrometry. Dehydration of the hydrotalcites occurred over a range of 56–70°C. The first dehydroxylation step occurred at around 255°C and, with the substitution of more iron(III) for chromium(III) this temperature increased to an upper limit of 312°C. This trend was observed throughout all decomposition steps. The release of carbonate ions as carbon dioxide gas initialised at just above 300°C and was always accompanied by loss of hydroxyl units as water molecules. The initial loss of the anion in this case the chloride ion was consistently observed to occur at about 450°C with final traces evolved at 535 to 780°C depending of the Fe:Cr ratio and was detected as HCl (m/z=36). Thus for this to occur, hydroxyl units must have been retained in the structure at temperatures upwards of 750°C. Experimentally it was found difficult to keep CO₂ from reacting with the compounds and in this way the synthesized iowaite-woodallite series somewhat resembled the natural minerals.     

Effects of Ti Addition on Alumina/Titania Composite Aerogels Synthesized by Sol–Gel Process and Supercritical Ethanol Drying

Alumina/titania composite aerogels with different titania contents were synthesized by the sol–gel process and supercritical ethanol drying. The structures and morphologies of synthesized aerogels were analyzed by X‐ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetry, and N₂ adsorption–desorption tests. Supercritical ethanol drying induced the crystallization of titania, which prompted the transformation of the structure from pseudoboehmite to γ‐Al₂O₃ . Reversely, alumina retarded the anatase‐to‐rutile transformation of titania. The content of titania significantly affected the structure and morphology of alumina/titania composite aerogels. A high content of titania (≥40%) resulted in the phase separation of titania particles, which grew to form the anatase phase octahedral particles with well‐developed facets. When the titania content was low, titania particles could be homogeneously dispersed in alumina particles to form spherical clusters with the poor crystallinity. Titania particles were in the anatase phase, and no rutile phase was formed until the temperature rose to 1000°C. In addition, titania addition resulted in a decrease in the specific surface area (SSA) of alumina aerogels because the SSA of titania was lower than that of alumina aerogels.     

Effects of calcining temperature on photocatalytic activity of Fe-doped sulfated titania

Using industrial titanyl sulfate as a raw material, Fe‐doped sulfated titania (FST) photocatalysts were prepared by using the one‐step thermal hydrolysis method and characterized using XRD, SEM, TGA–DSC, FTIR, UV–Vis DRS and N₂ adsorption–desorption techniques. The effects of calcining temperature on the structure of the titania were investigated. The photocatalytic activity of the FST was evaluated using the photodegradation of methylene blue and photooxidation of phenol in aqueous solutions under UV and visible light irradiation, respectively. The results evinced that Ti⁴⁺ is substituted by Fe³⁺ in titania lattice and forms impurity level within the band gap of titania, which consequently induces the visible light absorption and visible‐light‐driven photocatalytic activity. The synergistic effects of Fe‐doping and sulfation are beneficial to the efficient separation of the photogenerated carriers and also improve the quantum efficiency of photocatalysis. In addition, Brönsted acidity arisen from the strong inductive effect of sulfate is also conducive to enhancing the photocatalytic performance of FST. However, when the calcining temperature is higher than 800°C, sulfur species and surface hydroxyl groups decompose and desorb from FST and the specific surface area decreases sharply. Moreover, severe sintering and rutile phase formation occur simultaneously. All these are detrimental to photocatalytic activity of FST.     

Al (110) surface oxide thermal stability in ultrahigh vacuum

This research characterizes the stability of the Al₂O₃ surface oxide on Al (110) as a function of temperature and within an ultrahigh vacuum environment (p < 5 × 10^?12 Torr). Auger electron spectroscopy and temperature desorption spectroscopy were used to correlate the change in oxygen and carbon surface concentration. The surface oxide was observed to remain stable up to 350–400 °C. Above this temperature, the oxide began to dissociate resulting in a CO desorption peak at 425 °C followed by extensive dissolution of the C and O into the Al bulk. A second and much smaller CO desorption peak was observed at 590 °C in concert with complete oxide breakdown and the virtual disappearance of surface carbon and oxygen. Extrapolation of the Auger electron spectral ratios of C_KLL and O_KLL peaks to the sum of the Al⁰_LVV and Al³⁺_LVV peak suggests that the surface concentration of each approaches zero at ~640 °C. The predominant mechanism for reduction of the surface oxide occurs by dissolution into the bulk instead of desorption. Copyright © 2013 John Wiley & Sons, Ltd.     

Thermal behavior of a bentonite

The mineralogical composition of the Kütahya calcium bentonite (CaB) from Turkey was obtained as mass% of 60% calcium rich smectite (CaS), 30% opal-CT (OCT), trace amount illite (I), and some non-clay impurities by using chemical analysis (CA), X-ray diffraction (XRD), and thermal analysis (TG-DTA) data. The crystallinity, porosity, and surface area of the samples heated between 25–1300°C for 2 h were examined by using XRD, TG, DTA and N₂-adsorption-desorption data. The position of the 001 reflection which is the most characteristic for CaS does not affect from heating between 25–600°C and then disappeared. The decrease in relative intensity (I/I ₀) from 1.0 to zero and the increase in full width at half-maximum peak height (FWHM) from 0.25 to 1.0° of the 001 reflection show that the crystallinity of the CaS decreased continuously by rising the heating temperature from 25 to 900°C and then collapsed. The most characteristic 101 reflection for opals intensifies greatly between 900 and 1100°C with the opal becoming more crystalline. The total water content of the natural bentonite after dried at 25, 105 and 150°C for 48 h were determined as 8.8, 5.0 and 2.5%, respectively. The mass loss occurs between 25 and 400°C over two steps with the maximum rate at 80 and 150°C, respectively. The exact distinction of the dehydration temperatures for the adsorbed water and interlayer water is seen almost impossible. The temperature interval, maximum rate temperature, and mass loss during dehydroxylation are 400–800°C, 670°C and 4.6–5.0%, respectively. The maximum rate temperatures for decrystallization and recrystallization are 980 and 1030°C, respectively. The changes in specific micropore volume (V _mi), specific mesopore volume (V _me), specific surface area (S) were discussed according to the dehydration and dehydroxylation of the CaS. The V _mi, V _me and S reach to their maxima at around 400°C with the values of 0.045, 0.115 cm³ g⁻¹ and 90 m² g⁻¹, respectively. The radii of mesopores for the bentonite heated at 400°C are distributed between 1–10 nm and intensified approximately at 1.5 nm.     

On the Mechanism of Urea‐Induced Titania Modification

The mechanism of surface modification of titania by calcination with urea at 400 °C was investigated by substituting urea by its thermal decomposition products. It was found that during the urea‐induced process titania acts as a thermal catalyst for the conversion of intermediate isocyanic acid to cyanamide. Trimerization of the latter produces melamine followed by polycondensation to melem‐ and melon‐based poly(aminotri‐s‐triazine) derivatives. Subsequently, amino groups of the latter finish the process by formation of Ti? N bonds through condensation with the OH‐terminated titania surface. When the density of these groups is too low, like in substoichiometric titania, no corresponding modification occurs. The mechanistic role of the polytriazine component depends on its concentration. If present in only a small amount, it acts as a molecular photosensitizer. At higher amounts it forms a crystalline semiconducting organic layer, chemically bound to titania. In this case the system represents a unique example of a covalently coupled inorganic–organic semiconductor photocatalyst. Both types of material exhibit the quasi‐Fermi level of electrons slightly anodically shifted relative to that of titania. They are all active in the visible‐light mineralization of formic acid, whereas nitrogen‐modified titania prepared from ammonia is inactive.     

Vibrational analysis of sodium α-, β- and γ-hydroxybutyrates. Inter- and intramolecular hydrogen bonds

The infrared and Raman spectra of sodium α-, β- and γ-hydroxybutyrates and their deuterated analogues are examined in the 4000-100 cm⁻¹ range and an assignment of the fundamental vibrations is given. Based on the localization of the asymmetric stretching vibrations ν_asOH and the out-of-plane vibration γOH, inter- and/or intramolecularly hydrogen-bonded forms are proposed: the low frequencies of ν_asOH (<3200 cm⁻¹) and high frequencies of γOH (≈800 cm⁻¹) argue in favour of the existence of intramolecular hydrogen bonding. Sodium α-hydroxybutyrate exhibits as a chelate ring with an intramolecular hydrogen bond between hydroxyl and carboxyl groups, whereas sodium, β-hydroxybutyrate has the two association forms with inter- and intramolecular hydrogen bonds. Sodium γ-hydroxybutyrate exists as a hydrogen-bonded polymer, with an intermolecular hydrogen bond between the hydroxyl groups and between the hydroxyl and carbonyl groups. At a crystallization temperature above 50°C, only the α- salt showed a structural change indicating the existence of intra- and intermolecular hydrogen bonds. This result is confirmed by differential scanning analysis.     

Interfacial Impregnation Chemistry in the Synthesis of Cobalt Catalysts Supported on Titania

The interfacial chemistry of the impregnation step involved in the synthesis of cobalt catalysts supported on titania was investigated with regard to the mode of interfacial deposition of the aqua complex [Co(H₂O)₆]²⁺ on the “titania/electrolyte solution” interface, the structure of the inner‐sphere complexes formed, and their relative interfacial concentrations. Several methodologies based on the application of deposition experiments and electrochemical techniques were used in conjunction with diffuse‐reflectance spectroscopy and EPR spectroscopy. These suggested the formation of mononuclear/oligonuclear inner‐sphere complexes on deposition of the [Co(H₂O)₆]²⁺ ions at the “titania/electrolyte solution” interface. The joint application of semiempirical quantum‐mechanical calculations, stereochemical considerations, and modeling of the deposition data revealed the exact structure of these complexes and allowed their relative concentrations at various Co^II surface concentrations to be determined. It was found that the interface speciation depends on the Co^II surface concentration. Mononuclear complexes are formed at the compact layer of the “titania/electrolyte solution” interface for low and medium Co^II surface concentrations. Formation of mono‐hydrolyzed Ti₂O–TiO and the dihydrolyzed TiO–TiO disubstituted configurations is very probable. In the first configuration one water ligand of the [Co(H₂O)₆]²⁺ ion is substituted by a bridging surface oxygen atom and another by a terminal surface oxygen atom. In the second configuration two water ligands of the [Co(H₂O)₆]²⁺ ion are substituted by two terminal surface oxygen atoms. Binuclear and trinuclear inner‐sphere complexes are formed, in addition to the mononuclear ones, at relatively high Co^II surface concentrations.     

Aqueous colloidal sol–gel route to synthesize nanosized ceria-doped titania having high surface area and increased anatase phase stability

Nanocrystalline sol–gel derived titania doped with ceria (1, 2, 5 and 10-mole%) has been prepared from titanyl oxysulphate. The titania doped with 5-mole% CeO₂ after calcining to 500 °C, possesses specific surface area of 97 m² g⁻¹ and has anatase phase stability up to 900 °C. Moreover it retains a surface area of 37 m² g⁻¹ at 700 °C. In comparison, the undoped calcined material has anatase stability only up to 700 °C and specific surface area only 48 m² g^-1 and 6 m² g^-1 at 500 °C and 700 °C, respectively. The diffuse reflectance spectra show that, as the cerium content increases, the absorption undergoes a red shift and reaches the visible range. The exceptionally high phase stability, crystallinity and high surface area are due to the extremely fine particle size and effective doping achieved by the specific synthesis method. The results based on X-ray diffraction, specific surface area and diffuse reflectance spectra indicated that the maximum threshold limit of doping is up to a value of 5-mole%.