Simultaneous trace determination of nine organic UV-absorbing compounds (UV filters) in environmental samples

A new sensitive method has been successfully developed and validated for the simultaneous determination and quantification of nine estrogenic UV filters (benzophenone-1, benzophenone-2, benzophenone-3, benzophenone-4, 4,4-dihydroxybenzophenone, ethyl-4-aminobenzoate, 2-ethyl-hexyl-4-trimethoxycinnamate, 3-(4-methylbenzylidene)-camphor, 3-benzylidene-camphor) in different environmental matrices. After optimisation of extraction conditions for the best recovery of polar to lipophilic compounds from fish tissue and a subsequent lipid clean-up in HPLC, fish extraction recoveries exceeded 72% for all nine UV filters. Identification and quantification of compounds was performed for lipophilic UV filters with gas chromatography-electroionisation-mass spectrometry and for polar and mid-polar compounds with liquid chromatography coupled to electrospray ionisation mass spectrometry. Instrumental detection limits (IDL) varied between 5 and 260 pg injected and method detection limits (MDL) were in the low ng/g lipids range for all test compounds. The described analytical methods are shown to be useful to screen for estrogenic UV filters in environmental samples such as fish and polar organic chemical integrative samplers.     

Optimization of matrix solid-phase dispersion conditions for UV filters determination in biota samples

A low solvent consumption method for the determination of eight ultraviolet (UV) filters, displaying low to medium polarities, in freeze-dried samples of marine bivalves and fish is proposed. Matrix solid-phase dispersion (MSPD) and gas chromatography with mass spectrometry (GC-MS) were used as sample preparation and determination techniques, respectively. This work describes the influence of several parameters (type and amount of dispersant and clean-up sorbents, as well as elution solvent) on the yield and the selectivity of the MSPD extraction. Under optimized conditions, samples (0.5?g) were ground with 2?g of Florisil in a mortar with a pestle and transferred into a polypropylene syringe, which contained 1?g of C18 as clean-up sorbent. Analytes were eluted with 5?mL of acetonitrile. This extract was concentrated to dryness, re-constituted with 1?mL of ethyl acetate and injected in the GC-MS system without any further clean-up. The global average recoveries, measured for three different biota samples, spiked at three different levels (between 50 and 1000?ng?g^?1), ranged from 80% to 101% with associated standard deviations below 10%. The inter-day precision of the method varied from 4% to 15% and the achieved LOQs (defined for a signal to noise ratio of 10) ranged from 4 to 28?ng?g^?1, referred to the freeze-dried matrix. Octocrylene (OCR) was found in some samples of fish and mussels at concentrations between 15 and 20?ng?g^?1, referred to dry mass.     

Dechlorane Plus and related compounds in aquatic and terrestrial biota: a review

Dechlorane Plus, dechlorane 602, dechlorane 603 and dechlorane 604 are flame retardants that have been used for a long time as a substitute for mirex, but they have not been noticed as environmental contaminants until recently (2006). Regardless of their large molecular size and very high lipophilicity (log K _OW?>?9), Dechlorane Plus and related compounds have been detected in different aquatic and terrestrial species, supporting their bioaccumulation and biomagnification. Moreover, some studies showed different behaviour of the syn-Dechlorane Plus and anti-Dechlorane Plus isomers in the environment and different biomagnification factors in biota. This review describes the different analytical approaches applied to the determination of Dechlorane Plus and related compounds. Moreover, a summary of their levels in aquatic and terrestrial biota, as well as in humans, is presented, showing also current research results on their bioaccumulation and biomagnification potential. Finally, isomer-specific bioaccumulation of Dechlorane Plus is also discussed.     

Photolytic and photocatalytic degradation of organic UV filters in contaminated water

UV filters as emerging contaminants are of great concern and their wide detection in aquatic environments indicates their chemical stability and persistence. This review summarized the photolytic and photocatalytic degradation of UV filters in contaminated water. The findings indicated that limited research has been conducted on the photolysis and photocatalysis of UV filters. Photolysis of UV filters through UV irradiation in natural water was a slow process, which was accelerated by the presence of photosensitisers e.g. triplet state of chromaphoric dissolved organic matter (³CDOM*) and nutrients but reduced by salinity, dissolved organic matter (DOM) and divalent cations. UV Photocatalysis of 4-methylbenzylidene camphor and 2-phenylbenzimidazole-5-sulfonic acid was very effective with 100% removal within 30 min and 90 min using medicated TiO₂/H₂O₂ and TiO₂, respectively. The radiation source, type of catalyst and oxygen content were key factors. Future research should focus on improved understanding of photodegradation pathways and by-products of UV filters.     

An overview of the analytical methods for the determination of organic ultraviolet filters in biological fluids and tissues

Organic UV filters are chemical compounds added to cosmetic sunscreen products in order to protect users from UV solar radiation. The need of broad-spectrum protection to avoid the deleterious effects of solar radiation has triggered a trend in the cosmetic market of including these compounds not only in those exclusively designed for sun protection but also in all types of cosmetic products.     

The role of UV-B radiation in aquatic and terrestrial ecosystems--an experimental and functional analysis of the evolution of UV-absorbing compounds

We analysed and compared the functioning of UV-B screening pigments in plants from marine, fresh water and terrestrial ecosystems, along the evolutionary line of cyanobacteria, unicellular algae, primitive multicellular algae, charophycean algae, lichens, mosses and higher plants, including amphibious macrophytes. Lichens were also included in the study. We were interested in the following key aspects: (a) does the water column function effectively as an 'external UV-B filter'?; (b) do aquatic plants need less 'internal UV-B screening' than terrestrial plants?; (c) what role does UV screening play in protecting the various plant groups from UV-B damage, such as the formation of thymine dimers?; and (d) since early land 'plants' (such as the predecessors of present-day cyanobacteria, lichens and mosses) experienced higher UV-B fluxes than higher plants, which evolved later, are primitive aquatic and land organisms (cyanobacteria, algae, lichens, mosses) better adapted to present-day levels of UV-B than higher plants? Furthermore, polychromatic action spectra for the induction of UV screening pigments of aquatic organisms have been determined. This is relevant for translating 'physical' radiation measurements of solar UV-B into 'biological' and 'ecological' effects. From the action spectra, radiation amplification factors (RAFs) have been calculated. These action spectra allow us to determine any mitigating or antagonistic effects in the ecosystems and therefore qualify the damage prediction for the ecosystems under study. We summarize and discuss the main results based on three years of research of four European research groups. The central theme of the work was the investigation of the effectiveness of the various screening compounds from the different species studied in order to gain some perspective of the evolutionary adaptations from lower to higher plant forms. The induction of mycosporine-like amino acids (MAAs) was studied in the marine dinoflagellate Gyrodinium dorsum, the green algal species Prasiola stipitata and in the cyanobacterium Anabaena sp. While visible (400-700 nm) and long wavelength UV-A (315-400 nm) showed only a slight effect, MAAs were effectively induced by UV-B (280-315 nm). The growth of the lower land organisms studied, i.e. the lichens Cladina portentosa, Cladina foliacaea and Cladonia arbuscula, and the club moss Lycopodiumannotinum, was not significantly reduced when grown under elevated UV-B radiation (simulating 15% ozone depletion). The growth in length of the moss Tortula ruralis was reduced under elevated UV-B. Of the aquatic plants investigated the charophytes Chara aspera showed decreased longitudinal growth under elevated UV-B. In the 'aquatic higher plants' studied, Ceratophyllum demersum, Batrachium trichophyllum and Potamogeton alpinus, there was no such depressed growth with enhanced UV-B. In Chara aspera, neither MAAs nor flavonoids could be detected. Of the terrestrial higher plants studied, Fagopyrum esculentum, Deschampsia antarctica, Vicia faba, Calamagrostis epigejos and Carex arenaria, the growth of the first species was depressed with enhanced UV-B, in the second species length growth was decreased, but the shoot number was increased, and in the latter two species of a dune grassland there was no reduced growth with enhanced UV-B. In the dune grassland species studied outdoors, at least five different flavonoids appeared in shoot tissue. Some of the flavonoids in the monocot species, which were identified and quantified with HPLC, included orientin, luteolin, tricin and apigenin. A greenhouse study with Vicia faba showed that two flavonoids (aglycones) respond particularly to enhanced UV-B. Of these, quercetin is UV-B inducible and mainly located in epidermal cells, while kaempferol occurs constitutively. In addition to its UV-screening function, quercetin may also act as an antioxidant. Polychromatic action spectra were determined for induction of the UV-absorbing pigments in three photosynthetic organisms, representing very different taxonomic groups and different habitats. In ultraviolet photobiology, action spectra mainly serve two purposes: (1) identification of the molecular species involved in light absorption; and (2) calculation of radiation amplification factors for assessing the effect of ozone depletion. Radiation amplification factors (RAFs) were calculated from the action spectra. In a somewhat simplified way, RAF can be defined as the percent increase of radiation damage for a 1% depletion of the ozone layer. Central European summer conditions were used in the calculations, but it has been shown that RAF values are not critically dependent on latitude or season. If only the ultraviolet spectral region is considered, the RAF values obtained are 0.7 for the green alga Prasiola stipitata, 0.4 for the dinoflagellate Gyrodinium dorsum, and 1.0 for the cyanobacterium Anabaena sp. In the case of P. stipitata, however, the effect of visible light (PAR, photosynthetically active radiation, 400-700 nm) is sufficient to lower the RAF to about 0.4, while the PAR effect for G. dorsum is negligible. RAFs for some damage processes, such as for DNA damage (RAF=2.1 if protective effects or photorepair are not considered [1]), are higher than those above. Our interpretation of this is that if the ozone layer is depleted, increased damaging radiation could overrule increased synthesis of protective pigments. In addition to investigating the functional effectiveness of the different screening compounds, direct UV effects on a number of key processes were also studied in order to gain further insight into the ability of the organisms to withstand enhanced UV-B radiation. To this end, the temperature-dependent repair of cyclobutane dimers (CPD) and (6-4) photoproducts induced by enhanced UV-B was studied in Nicotiana tabacum, and the UV-B induction of CPD was studied in the lichen Cladonia arbuscula. Also, photosynthesis and motility were monitored and the response related to the potential function of the screening compounds of the specific organism.     

Hetarylation of organic compounds (review)

Reactions of the direct introduction of nitrogenous aromatic heterocycles into nucleophilic organic compounds with the use in situ of N-acyl salts of heterocyclic cations and also of heteroaromatic anion radicals are discussed.     

Analysis of emerging and related pollutants in aquatic biota

Water bodies cover approximately 70 % of the earth´s surface, making them ecosystems with a high environmental value and the habitat for numerous species of flora and fauna. Emerging pollutants (EPs) are ubiquitous anthropogenic compounds of environmental concern that can be found at different concentration levels in matrices such as sediment, water and aquatic biota. In addition, EPs can be bioaccumulated and biomagnified, inducing adverse effects on biota, and posing a risk to humans when contaminated biota is consumed. Unlike abiotic matrices, the occurrence of EPs in aquatic biota has not been widely studied. This is probably because their complexity, due to the presence of lipids, proteins and other organic compounds, makes the extraction and analysis of EPs difficult. This review gathers the most relevant analytical methods published between 2014 and 2019, comparing them and evaluating their strengths and weaknesses. It is intended to provide a better understanding of the development of new and improved methods, and to be a reference for researchers who are looking for the best methodology for their studies.     

Pyrolysis methods in organic geochemistry: An overview

In recent years it has been realized by geochemists that pyrolysis techniques can provide successful and rapid analyses of sedimentary organic material, including petroleums, coals, oil shales and their precursors. This article represents an introductory overview of the literature of the last 25 years pertaining to geochemical pyrolysis studies. The overview introduces non-geochemists to the many areas in academic and industrial geochemistry to which pyrolysis in general, and analytical pyrolysis in particular, are applicable.     

Metal(loid)organic compounds in contaminated soil

13 samples of soils contaminated with petrol, coaly residues, shredder and domestic waste have been investigated by low temperature gas chromatography with plasma mass spectrometry detection after sample derivatisation by hydride generation (HG/LT-GC/ICP-MS). 24 organic compounds of 9 elements could be analysed, one fifth of them exceeding the concentration of 1 microg/kg. These results are roughly comparable with those on harbour and river sediments, and are discussed in respect to a preliminary evaluation of the emission potential of solid waste and contaminated soil as well as waste treatment processes.     

Applications of bismuth(III) compounds in organic synthesis

This review article summarizes the applications of bismuth(III) compounds in organic synthesis since 2002. Although there are an increasing number of reports on applications of bismuth(III) salts in polymerization reactions, and their importance is acknowledged, they are not included in this review. This review is largely organized by the reaction type although some reactions can clearly be placed in multiple sections. While every effort has been made to include all relevant reports in this field, any omission is inadvertent and we apologize in advance for the same (358 references).     

Heterocyclic compounds as organic luminophores (review)

A review of heterocyclic compounds having luminescence properties is given. Methods for the preparation of some of them, the relationship between structure and luminescence, and their areas of application are examined.     

Photoactivity of kynurenine-derived UV filters

Quantum yields of photodecomposition and triplet state formation under aerobic and anaerobic conditions are determined for kynurenine (KN), 3-hydroxykynurenine (3OHKN), xanthurenic acid (XAN), and kynurenine adducts of glutathione (GSH-KN), cysteine (Cys-KN), histidine (His-KN), and lysine (Lys-KN) in aqueous solutions. The highest yields of anaerobic photodecomposition were obtained for GSH-KN and His-KN adducts, which correlates with the highest triplet yields for these compounds. In aerobic conditions, the photodecomposition yields for all compounds under study increase; the highest decomposition rates were observed for His-KN and 3OHKN. The fast decomposition of the latter is attributed to the dark autoxidation of the starting compound.     

Determination of arsenic compounds in reference materials by HPLC-(UV)-HG-AFS

Arsenic compounds were determined in six reference materials of biological origin. None of them has yet been certified for arsenic compounds but some are in the process of certification; for most of these reference materials indicative literature values are available. Eight commonly used arsenic standards were used for quantification using a recently developed hyphenated speciation system comprising high performance liquid chromatography (HPLC) and atomic fluorescence spectrometry (AFS), interfaced via a UV-photoreactor and a hydride generation (HG) unit. Absolute detection limits were ca. 0.2 and 0.4 ng As for separation on anion and cation exchange columns, respectively. Our results agree well with indicative literature values which were generated by different authors using various separation and detection methods. The HPLC-(UV)-HG-AFS system validated in this way is suitable for quantification of eight arsenic compounds. Moreover, the system is capable of separation of at least six more compounds in the mentioned reference materials, of which two could be attributed to arsenosugars (OH and phosphodiester form) but due to the lack of standards, quantification was not possible. For accurate and extensive speciation analysis the availability of certified reference materials and standards for arsenic compounds should be promoted.     

Microbial calorimetric analysis (MCA) of aqueous organic compounds

Adapted bacteria used in heat conduction calorimetry may be developed as 'analytical reagents' for compounds that can be metabolized by such bacteria. Adaption can be done by growing cells such as E. coli on the analyte of interest, for example a sugar. Samples to be analyzed are mixed with adapted cells which aerobically metabolize the sought-for analyte, producing heat. The method is called microbial calorimetric analysis, MCA. Average requirements are 2-200 nanomoles of analyte, "carbon", an excess of cells ca. 2-5 mg of cells, and 1-2 ml of air to maintain aerobicity. Heat production is usually completed in 300-600 sec at 25 degrees. The combination of bacteria and heat conduction calorimetry is a sensor system having a sensitivity and selectivity dependent on bacterial adaption. The system is useful in analytical problems when analytes are in turbid suspension, are poor chromogens or not even prochromogenic. MCA takes advantage of the large aerobic heats usually generated by bacteria in active utilization of organic analytes. Typically from 20 to 70 kcal exothermic heat per mole of carbon atoms is generated, e.g., (-)300 kcal/mole glucose. Heat conduction calorimeters, batch mixing instruments, measure 2-100 millicalorie heat with +/-3% error in each run. Bacteria can be grown on many different kinds of compounds. Accordingly it is fairly easy to create diverse, specific 'analytical reagents' which function in MCA much as they function in their usual environment, in soils, etc. Intact, adapted bacteria have decided advantages over isolated enzymes as 'biosensors' for a number of practical reasons.     

Determination of complex mixtures of volatile organic compounds in ambient air: an overview

This article reviews developments in the sampling and analysis of volatile organic compounds (VOCs) in ambient air since the 1970s, particularly in the field of environmental monitoring. Global monitoring of biogenic and anthropogenic VOC emissions is briefly described. Approaches used for environmental monitoring of VOCs and industrial hygiene VOC exposure assessments are compared. The historical development of the sampling and analytical methods used is discussed, and the relative advantages and disadvantages of sorbent and canister methods are identified. Overall, there is considerable variability in the reliability of VOC estimates and inventories. In general, canister methods provide superior precision and accuracy and are particulary useful for the analysis of complex mixtures of VOCs. Details of canister methods are reviewed in a companion paper. C. C. Austin is an Invited Scientist of the National Research Council of Canada.     

An overview of heterogeneous photocatalysis for the degradation of organic compounds: A special emphasis on photocorrosion and reusability

Heterogeneous photocatalysis has been extensively investigated for the degradation of organic pollutants from wastewater. The remarkable advantages of the heterogeneous photocatalysis process depend upon its ability to produce reactive oxygen species under visible/UV/solar light irradiation. However, the long-term stability and reuse potential of these catalysts are of great concern these days, yet understudied. This review aims to systematically present a state of the art understanding of such catalysts' reuse potential. Various important surface characteristics of the photocatalysts for improving the photostability and activity of the catalyst are discussed. Besides, the synergistic effect of different surface modified materials, composite materials and their surface characteristics for their enhanced activity are also covered. Finally, a discussion on various regeneration processes used for such catalysts is also presented, identifying some vital research needs in this field.     

Arylidene pyruvic acids (APAs) in the synthesis of organic compounds

1. Download : Download full-size image

     

Speciation analysis of antimony in marine biota by HPLC-(UV)-HG-AFS: Extraction procedures and stability of antimony species

Speciation analysis of antimony in marine biota is not well documented, and no specific extraction procedure of antimony species from algae and mollusk samples can be found in the literature. This work presents a suitable methodology for the speciation of antimony in marine biota (algae and mollusk samples). The extraction efficiency of total antimony and the stability of Sb(III), Sb(V) and trimethylantimony(V) in different extraction media (water at 25 and 90 °C, methanol, EDTA and citric acid) were evaluated by analyzing the algae Macrosystis integrifolia (0.55 ± 0.04 μg Sb g⁻¹) and the mollusk Mytilus edulis (0.23 ± 0.01 μg Sb g⁻¹). The speciation analysis was performed by anion exchange liquid chromatography (post-column photo-oxidation) and hydride generation atomic fluorescence spectrometry as detection system (HPLC-(UV)-HG-AFS). Results demonstrated that, based on the extraction yield and the stability, EDTA proved to be the best extracting solution for the speciation analysis of antimony in these matrices. The selected procedure was applied to antimony speciation in different algae samples collected from the Chilean coast. Only the inorganic Sb(V) and Sb(III) species were detected in the extracts. In all analyzed algae the sum of total antimony extracted (determined in the extracts after digestion) and the antimony present in the residue was in good agreement with the total antimony concentration determined by HG-AFS. However, in some extracts the sum of antimony species detected was lower than the total extracted, revealing the presence of unknown antimony species, possibly retained on the column or not detected by HPLC-(UV)-HG-AFS. Further work must be carried out to elucidate the identity of these unknown species of antimony.