Determination of lincomycin and tylosin residues in honey by liquid chromatography/tandem mass spectrometry

A simple and rapid analytical method was developed for the determination of lincomycin and tylosin residues in honey as part of field studies examining the efficacy and target animal safety of these antibiotics to control American foulbrood disease in honey bees. Residues of the antibiotics were determined using liquid chromatography/electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS). Honey samples were diluted and injected directly into the LC/MS/MS system without additional cleanup by solid-phase extraction or liquid-liquid partitioning. A six-port valve system was utilized to selectively route eluant from the LC column into the mass spectrometer only during a relatively short portion of the chromatographic run corresponding to the elution of the analytes of interest. Minimal contamination of the MS source chamber was observed despite the analysis of large numbers of samples. Using internal standard quantitation, excellent accuracy and precision were obtained with no apparent matrix-to-matrix variation. Based on the analysis of fortified replicates, the mean percent deviation from the theoretical concentration and the percent relative standard deviation were both less than 10% for tylosin over an analytical range of 10-1000 microg/kg. Slightly higher mean percent deviations and relative standard deviations were observed for the analysis of lincomycin in fortified replicate samples. The method detection limits were determined to be 5 and 2 microg/kg for lincomycin and tylosin, respectively.     

Calibration Point for Electron Ionization MS / MS spectra measured with multiquadrupole mass spectrometers

A protocol for establishing standard instrument conditions for measurement of product ion MS/MS spectra from parent ions produced by electron ionization is presented. Within this protocol, the ion at m/z 231 (C₅F₉ ⁺) from perfluorokerosene or perfluorotributylamine is selected as the parent ion and subjected to collision-induced dissociation. The relative intensities of product ions at m/z 69, 131, and 181 are monitored as a function of collision energy while keeping the target gas pressure constant within the range of 10^?4–10^?6 torr (measured), or a beam attenuation of approximately 30-70%. The collision energy at which the ion intensities for product ions at m/z 69 and 181 are equal is defined as the calibration point at that collision gas pressure; the intensity of the ion at m/z 131 is very close to this value as well. Electron ionization MS/MS spectra taken at the calibration point using two different multiquadrupole instruments show good reproducibility for several test compounds. The high degree of similarity may aid in the establishment of a MS/MS spectral library.     

Development of a Liquid Chromatography Tandem Mass Spectrometry Method for Identification of Flavonoids in Ginkgo biloba

A rapid, selective and sensitive method for analysis of trace flavonoids and its glycoside derivatives in ginkgo has proposed. Ultrasonic‐assisted extraction of sample preparation was adopted to extract trace flavonoids in ginkgo leaf and its processed product. The compounds were identified using liquid chromatography negative electrospray ionization triple quadrupole tandem mass spectrometry (MS/MS). The neutral loss scan mode of MS/MS was used to screen flavonoid compounds and those compounds with acid group, or having rhamnosyl, glucosyl, or coumaroyl moiety in the samples. The successive data‐dependent product ion scan mode of MS/MS was used to identify the structure of the components. The analytical results represented three aglycone flavonoids and seven flavonoid glycosides in ginkgo. The method detection limits were evaluated for the analytes analyzed in the range of 0.88 to 2.67 μg/mL.     

Sensitive and rapid method to determine trimetazidine in human plasma by liquid chromatography/tandem mass spectrometry

A simple, sensitive, and rapid liquid chromatographic/tandem mass spectrometric (LC/MS/MS) method, using electrospray ionization, was developed and validated to quantify trimetazidine in human plasma using propranolol hydrochloride as an internal standard (IS). Samples were prepared by solid-phase extraction and analyzed without drying and reconstitution. The analyte and IS were chromatographed on a C18 reversed-phase column under isocratic conditions using 2 mM ammonium acetate (pH 3.5)-acetonitrile (40 + 60, v/v) as the mobile phase with a run time of 2.0 min. Quantitation was done on a triple-quadrupole mass analyzer API-3000, equipped with turbo ion spray interface and operating in multiple reaction monitoring mode to detect parent --> product ion (m/z 267.2 --> 181.4) transition. The method was validated for sensitivity, accuracy and precision, linearity, recovery, matrix effect, and stability. Linearity in plasma was observed over the concentration range of 1.5-300 ng/mL. Lower limit of quantification achieved was 1.5 ng/mL with precision < 10% using 10 microL injection volume. The mean relative recovery of analyte (97.36%) and IS (99.93%) was consistent and reproducible. Interbatch and intrabatch precision was < 8.0% and the accuracy determined was within +/- 8% in terms of relative error.     

Solid-phase extraction coupled with liquid chromatography-tandem mass spectrometry for determination of trace rosiglitazone in urine

This project evaluated solid-phase extraction (SPE) combined with liquid chromatography-tandem mass spectrometry (LC-MS/MS) to determine the trace amount of rosiglitazone in human urine. The analytical performance of four modes of LC-MS and tandem MS operation (atmospheric pressure chemical ionization (APCI), electrospray ionization (ESI), positive and negative ionization) was compared for two mass spectrometers, a triple-quadrupole and a quadrupole ion trap instrument. Rosiglitazone was extracted from urine using a SPE cartridge of 50mg C8 sorbent and acetonitrile used as the eluting solvent. Samples were then separated on a RP18 column interfaced with a tandem mass spectrometer. The recovery of rosiglitazone was greater than 91.2%. The urine assay combining SPE and LC-APCI-MS/MS of triple-quadrupole was proved a very selective and sensitive method for determination of trace rosiglitazone. The assay was linear over a wide range, with a lower limit of quantification of 0.1 ng/mL using 1 mL of urine. The intra- and inter-day precisions were <9.8% and <7.9%, respectively, and the accuracies were in the range 91.0-103.6%. The rosiglitazone concentration profile in human urine was also determined. The results of this study reveal the adequacy of SPE-LC-APCI-MS/MS method for analyzing rosiglitazone from diabetic patients' urines. The concentrations of rosiglitazone were detected to range from 760 to 164 pg/mL.     

Toxaphene analysis in Great Lakes fish: a comparison of GC-EI/MS/MS and GC-ECNI-MS, individual congener standard and technical mixture for quantification of toxaphene

Toxaphene is considered to be a problematic organochlorine pollutant because of its bioaccumulation potential and persistence in aquatic environments. In this study, whole lake trout and walleye composites were used to evaluate two analytical techniques for total toxaphene and selected congener analysis. The efficacy of using gas chromatography electron ionization tandem mass spectrometry (GC-EI/MS/MS) and electron capture negative ionization mass spectrometry (GC-ECNI-MS) were compared. Although the sensitivity using GC-ECNI-MS was approximately five times greater than GC-EI/MS/MS, the latter provided more consistent inter-Parlar relative response factors (RRF). When using technical calibration mixtures, these results suggest a more accurate total toxaphene measurement was obtained using the GC-EI/MS/MS method. Total toxaphene concentrations in lake trout composites from both methods were highly correlated (R ² = 0.985) with the MS/MS concentrations approximately half of those determined by ECNI, suggesting systematic high bias in toxaphene concentrations when measured using GC-ECNI.     

Quantitative determination of tiopronin in human plasma by LC-MS/MS without derivatization

Tiopronin (TP) is a synthetic thiol compound without chromophore. By optimizing the chromatographic conditions and sample preparation processes, an improved LC‐MS/MS analytical method without derivatization has been developed and validated to determine TP concentrations in human plasma. After reduction with 1,4‐dithiothreitol, plasma samples were deproteinized with 10% perchloric acid. The post‐treatment samples were analyzed on a C₈ column interfaced with a triple quadrupole tandem mass spectrometer in negative electrospray ionization mode. Methanol–5 mmol/L ammonium acetate (20:80, v/v) was used as the isocratic mobile phase. The assay was linear over the concentration range of 40.0–5000 ng/mL. The intra‐ and inter‐day precisions were within 12.9% in terms of relative standard deviation and the accuracy within 5.6% in terms of relative error. This simple and sensitive LC‐MS/MS method with short analytical time (3.5 min each sample) was successfully applied to the pharmacokinetic study of TP in healthy Chinese male volunteers after an oral dose of 300 mg TP. Copyright © 2011 John Wiley & Sons, Ltd.     

Application of an integrated matrix-assisted laser desorption/ionization time-of-flight, electrospray ionization mass spectrometry and tandem mass spectrometry approach to characterizing complex polyol mixtures

Polyols are being used in a wide range of industrial applications including surfactants and precursors for grafted polymers. The characterization of polyols is of significance in correlating compositions and structures with their properties. We illustrate two real world examples where traditional analytical methods including GPC and NMR failed to reveal compositional differences, but the combination of matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF), electrospray ionization mass spectrometry (ESI MS), and MS/MS can produce compositional information required for problem solving. The first example involves failure analysis of four ethylene oxide and propylene oxide (EO/PO) copolymer products. The results from the mass spectrometry analysis unequivocally demonstrate that one of the samples has a small variation in copolymer composition, leading to its abnormal activity. The second example is in the area of deformulation of complex polyol mixtures. Two samples displaying similar properties and activities were found to be two different polyol blends. One of the samples is a more cost-effective product. These examples demonstrate that MALDI, ESI MS, and MS/MS should be seriously considered as an integrated component of an overall polyol characterization program in product failure analysis and deformulation.     

DNA assay based on monolayer-barcoded nanoparticles for mass spectrometry in combination with magnetic microprobes

Mass spectrometry (MS) based methodology offers simple, fast and sensitive diagnosis. While it has become the predominate approach in biomolecular analysis, it has not been suitable for analyzing nucleic acid due to its low ionization efficiency. We report herein on a DNA assay based on monolayer-barcoded nanoparticles that were encoded with reporter mass molecules, which act as surrogate molecules for the matrix-assisted laser desorption/ionization time-of-flight MS (MALDI-TOF MS) identification of target DNA through mass spectrometry in combination with magnetic microprobes. This assay demonstrated high MS sensitivity, with the ability to detect target DNA at femtomolar (10⁻¹⁵ M) levels. This inaugural effort using combined techniques is significant because it showed an extraordinary analytical capability for differentiating the single nucleotide polymorphism (SNP), which comprises the most abundant source of genetic variation in the human genome. We also report herein the feasibility of MS detection of two target DNAs that have the same mass but different nucleotide base composition, which classic MS methodology is inherently unable to differentiate.     

气相色谱-质谱法分析蜂蜜中的多种农药残留

开展了蜂蜜中23种农药残留的气相色谱-电子轰击离子源质谱(GC-EI/MS)分析方法的研究,并对其中3种农药的EI/MS碎片离子的断裂机理与结构进行了初步解析。探讨了蜂蜜试样前处理条件的优化与选择。将蜂蜜试样用乙酸乙酯提取剂超声提取、Florisil硅藻土色谱柱净化和正己烷-乙酸乙酯(体积比为7∶3)混合洗脱剂洗脱后,以PCB103为内标物,采用选择离子监测(SIM)方式下的GC-EI/MS分析。当试样的加标浓度为50,100和200 μg/kg时,加标回收率为82%～120%,相对标准偏差小于11.0%。23种农药的检测限都小于10.0 μg/kg,线性范围为10～500 μg/kg,相关系数都大于0.995。此分析方法已成功地应用于蜂蜜中23种痕量农药残留的分析。     

Terpolymerization of maleic anhydride with vinyl monomers

The relative reactivity of vinyl monomers characterized by electron donor and electron acceptor properties in free radical terpolymerization with maleic anhydride has been compared on the basis of product composition analysis. Terpolymers containing ca. 50 mol % of maleic anhydride were obtained in systems containing two electron donor monomers and the relative reactivity of them increases in the following order: 1-hexene < propylene ≈ isobutylene < styrene < isoprene < 1,3-butadiene. In systems consisting of an electron donor monomer and two electron acceptor monomers (i.e., maleic anhydride and an acrylic monomer), the composition of the terpolymers formed depends essentially on the resonance stabilization of the electron donor monomer. With a rise of their resonance stabilization, the content of acrylic monomeric units decreases and the share of alternating sequences of the electron donor and maleic anhydride monomeric units increases. It was found that the relative reactivity of maleic anhydride in all such systems is much greater than that predicted on the basis of reactivity ratios determined in binary systems. The relative reactivity of the studied acrylic monomers decreases in the order: methyl methacrylate > methyl acrylate > acrylonitrile. In the presence of catalytic amounts of ZnCl₂ the content of acrylic monomeric units clearly increases in the products obtained, mainly as a result of homopropagation. The results obtained are discussed in terms of the classical mechanism of propagation and the complex participation model.     

固相萃取-超高效液相色谱-电喷雾串联质谱法同时测定地表水中9种微囊藻毒素

建立了固相萃取-超高效液相色谱-电喷雾串联三重四极杆质谱(SPE-UPLC-ESI-MS/MS)联用技术分析水中9种微囊藻毒素的方法。样品经SPE提取和净化后,以Waters ACQUITY UPLCTM BEH C18色谱柱为分离柱,以含0.1%甲酸乙腈和含0.1%甲酸水作为流动相进行梯度洗脱,电喷雾离子源电离、正离子多反应监测模式质谱进行定性和定量分析。9种微囊藻毒素在0.1～50 μg/L或0.5～100 μg/L质量浓度范围内线性良好,相关系数为0.9990～0.9998,方法的检出限(以3倍信噪比计)为0.1～0.5 ng/L;高、中、低3个添加水平的回收率为75.8%～109%,相对标准偏差为0.49%～10.0%。结果表明,该方法灵敏、准确,检测范围广,分析速度快。应用该方法检测了杭州市两处水库水样中的微囊藻毒素,分别检出了3种和8种微囊藻毒素。     

高效液相色谱-串联质谱法检测奶中克拉维酸残留

采用高效液相色谱-串联质谱(HPLC-MS/MS)建立了克拉维酸在奶中的残留检测方法。2 g样品经乙醇沉淀蛋白质后,转入鸡心瓶中旋转蒸发浓缩至0.5 mL左右,用乙酸铵定容,净化后检测。流动相为乙腈和0.1%甲酸水,梯度洗脱,经Luna 5u C8色谱柱分离,采用电喷雾电离,多反应监测负离子模式对克拉维酸进行定量分析。采用基质匹配法对奶中克拉维酸的含量进行标准校正,在克拉维酸含量为10～400 μg/kg范围内呈现良好的线性关系,相关系数大于0.999;奶中加标样品的检出限(LOD,按信噪比(S/N)≥3计)为10 μg/kg,定量限(LOQ, S/N≥10)为20 μg/kg。在定量限、1/2最高残留限量、最高残留限量、2倍最高残留限量添加水平下,奶中克拉维酸的平均回收率为80.00%～91.25%,相对标准偏差为5.60%～8.77%。该方法可用于奶中克拉维酸残留的分析检测。     

On-line cloud point extraction combined with electrothermal vaporization inductively coupled plasma atomic emission spectrometry for the speciation of inorganic antimony in environmental and biological samples

The present paper describes an analytical method based on liquid chromatography coupled to tandem mass-spectrometry (LC-MS/MS) for the determination of acrylamide in foodstuffs. Atmospheric pressure chemical ionization (APCI) as ionization source and an ion-trap (LCQ) analyzer were used, and to the best of our knowledge, this hyphenated technique has not ever been employed to this purpose. In order to obtain clean extracts an improved purification procedure based on the coupling of two highly cross-linked polystyrene-divinylbenzene polymeric sorbents: Strata-X-C and ENV+, was also developed. High recoveries (85%) and good reproducibility (relative standard deviation of 12%) were obtained using the two solid-phase extraction cartridges in combination. One hundred percent water as mobile phase was used for the LC separation. The obtained figures of merit showed detection limits of 250 pg for standards and 45 ng/g for samples, and run-to-run and day-to-day precisions of 3.3 and 8%, respectively. Acrylamide (AA) was determined in several of the most frequently eaten carbohydrate-rich foodstuffs commercialized in Spain such as potato crisps and chips, biscuits, crisp breads, pastry, dried fruits, chocolates and coffee. For the first time, a typical pastry product called as “churros” and highly consumed in Spain was also studied. Some of the products tested such as french fries frozen or “churros” were household cooked. Acrylamide was determined in the selected food commodities using the developed analytical methodology. A commonly used method by liquid chromatography coupled to tandem mass-spectrometry with a triple quadrupole as mass analyzer (LC-QqQ-MS/MS) was also applied in order to validate the analytical results. Different levels of acrylamide were obtained and pastry and dried fruits showed the lower levels (<20 ng/g). Potato chips and french fries gave values of the order of 500-9250 ng/g.     

Imaging with mass spectrometry: Which ionization technique is best?

The use of mass spectrometry (MS) to acquire molecular images of biological tissues and other substrates has developed into an indispensable analytical tool over the past 25 years. Imaging mass spectrometry technologies are widely used today to study the in situ spatial distributions for a variety of analytes. Early MS images were acquired using secondary ion mass spectrometry and matrix-assisted laser desorption/ionization. Researchers have also designed and developed other ionization techniques in recent years to probe surfaces and generate MS images, including desorption electrospray ionization (DESI), nanoDESI, laser ablation electrospray ionization, and infrared matrix-assisted laser desorption electrospray ionization. Investigators now have a plethora of ionization techniques to select from when performing imaging mass spectrometry experiments. This brief perspective will highlight the utility and relative figures of merit of these techniques within the context of their use in imaging mass spectrometry.     

Influence of structural features of isomeric hydrocarbons on ion formation at atmospheric pressure

Ion mobility spectrometry (IMS) in combination with different techniques of atmospheric pressure ionization (⁶³Ni ionization, photoionization, Corona discharge ionization) was applied to determine the influence of structural features of aromatic and cyclic hydrocarbons on ion mobility spectra. For this purpose, different sets of isomeric hydrocarbons were investigated using the above-mentioned ionization techniques. We found different structural features of these isomeric non-polar compounds which cause distinct differences in ion mobility spectra. These differences result from the formation of different product ions or a different relative abundance of ions formed depending on the occurrence of certain structural features (position of the double bond, arrangement of double bonds within the carbon ring, configuration of aliphatic side chain in the space, position of aliphatic side chain on the carbon ring and the number of carbon atoms in the aliphatic side chain). The nature of product ions formed was determined using a coupling of IMS with mass spectrometry (MS).     

The preparation of novel 1-propenyl ethers and their cationic photopolymerization

A series of nine difunctional 1-propenyl ether monomers bearing ether, ester, carbonate, and urethane groups were prepared based on trimethylolpropane diallyl ether as the starting material. The monomers were fully characterized and then subjected to photoinitiated cationic polymerization using diaryliodonium salts as photoinitiators. The course of the polymerizations was followed using Fourier transform real-time infrared spectroscopy and the relative reactivities of the various monomers were determined. It could be shown that the differences in reactivity could be related mainly to the basicity of the functional group introduced into the molecule. © 1996 John Wiley & Sons, Inc.     

A rapid HPLC/ESI‐MS/MS method for quantitative analysis of isovalerylshikonin in rat plasma

A new, fast and sensitive high‐performance liquid chromatography/electrospray ionization tandem mass spectrometry (HPLC/ESI‐MS/MS) method was developed and validated for isovalerylshikonin in rat plasma using emodin as internal standard (IS). The analyte was extracted from rat plasma with ethyl acetate, after 10% HCl treatment and protein precipitated by methanol. The compound was separated on an Ultimate? XB‐C₁₈ analytical column using a mobile phase of methanol–10 mM ammonium acetate in water–acetonitrile containing 0.05% formic acid (45 : 10 : 45, v/v/v) with isogradient elution. The analyte was detected in negative ion mode using multiple‐reaction monitoring. The method was validated and the specificity, linearity, lower limit of quantitation (LLOQ), precision, accuracy, recoveries and stability were determined. LLOQ was 9 ng/mL for isovalerylshikonin. Correlation coefficient (r) value for the linear range of the analyte was greater than 0.99. The intra‐day and inter‐day precision and accuracy were better than 8.52%. The relative and absolute recovery was above 86% and no matrix effects were observed for isovalerylshikonin. This validated method provides a modern, rapid and robust procedure for the pharmacokinetic study of the two compounds in rats after intravenous administration to rats (n = 4). Copyright © 2009 John Wiley & Sons, Ltd.     

Using Electron Induced Dissociation (EID) on an LC Time-Scale to Characterize a Mixture of Analogous Small Organic Molecules

LC ESI FTICR MS of a sample of cediranib identified this pharmaceutical target molecule plus an additional 10 compounds of interest, all of which were less than 10% total ion current (TIC) peak intensity relative to cediranib. LC FTICR tandem mass spectrometry using electron induced dissociation (EID) has been achieved and has proven to be the best way to generate useful product ion information for all of these singly protonated molecules. Cediranib [M + H]⁺ fragmented by EID to give 29 product ions whereas QTOF-CID generated only one very intense product ion, and linear ion trap-CID, which generated 10 product ions, but all with poor S/N. Twenty-six of the EID product ions were unique to this fragmentation technique alone. By considering the complementary LC-EID and LC-CID data together, all 10 unknown compounds were structurally characterized and proven to be analogous to cediranib. Of particular importance, EID produced unique product ion information for one of the low level cediranib analogues that enabled full characterization of the molecule such that the presence of an extra propylpyrrolidine group was discovered and proven to be located on the pyrrolidine ring of cediranib, solving an analytical problem that could not be solved by collision induced dissociation (CID). Thus, it has been demonstrated that EID is in harmony with the chromatography duty-cycle and the dynamic concentration range of synthetic compounds containing trace impurities, providing crucial analytical information that cannot be obtained by more traditional methodologies.     

电喷雾萃取电离质谱法检测1-羟基芘

采用电喷雾萃取电离质谱(EESI-MS)分析致癌性环境有机污染物多环芳烃(PAHs)生物标志物1-羟基芘(1-OHP),探究1-OHP在EESI源中电离的可行性,考察ESI溶剂和样品溶液组成对方法灵敏度的影响,初步建立I-OHP的EESI MS半定量分析方法.结果表明,溶液中1-OHP能够在EES1源中有效电离,生成准分子离子[M-H]- (m/z 217),并得到其二级质谱特征碎片离子[M- H- CO]- (m/z 189);水、甲醇、乙醇、正丙醇和正丁醇5种ESI溶剂中,使用甲醇时,离子峰m/z 217信噪比最大.样品溶液中甲醇含量越高,离子峰m/z 217强度越强.离子峰m/z 217强度与1-OHP浓度在10～200 μg/L内的线性相关性相对最好;相关系数(R)0.982;相对标准偏差(RSD)为3.4％～14.0％(n=5);定量下限约为10 μg/L(S/N=10);单次检测时间小于0.5 min.