低轴径比CrCoAPO-5分子筛的合成与表征

通过控制合成液制备温度、晶体晶化速度等因素, 调控CrCoAPO-5分子筛颗粒的形貌及大小。合成的分子筛颗粒采用SEM、XRD、FT-IR、UV-Vis、TG、BET、ICP-OES等进行表征。结果表明低温5 ℃配制的合成液引入晶种后, 在传统水热条件下150 ℃晶化4.5 h, 可制备出直径3 μm、轴径比小于0.2的六边形片状分子筛颗粒。相对于较大颗粒的样品具有较短的扩散孔道, 更高的催化活性。     

无模板剂预晶化液添加法合成ZSM-5分子筛

研究了旋转烘箱中无模板剂条件下,预晶化液添加对合成ZSM-5分子筛的影响。系统研究了预晶化液加入量对合成分子筛晶化速率及颗粒大小的影响。采用X射线衍射,扫描电镜,N2吸附-脱附,和激光粒度分布等分析方法对合成的ZSM-5分子筛样品的物化性能进行了表征。结果表明,预晶化液的添加可以明显加快分子筛的晶化速率,预晶化液添加量为33.3wt%时达到最大结晶度的合成时间由未添加时的48 h减少到24 h。添加预晶化液的母液在150℃晶化24 h时所得ZSM-5分子筛团聚体的颗粒大小随着预晶化液加入量的增大而增大,由5.5μm增大到26.3μm。团聚体颗粒的比表面积比未添加预晶化液得到的分子筛(292 m2.g-1)有了不同程度的提高,如添加量为33.3wt%时为394 m2.g-1。对预晶化液添加法合成ZSM-5分子筛团聚体颗粒的生长机理进行了讨论。     

ZSM-5分子筛结晶度及晶粒大小的影响因素

以硅溶胶为硅源,偏铝酸钠为铝源,用晶种法制备ZSM-5分子筛.考察了物料混合方式、陈化时间、晶化时间、晶化温度、碱度和水量等对ZSM-5分子筛相对结晶度和晶粒大小的影响.用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和激光粒度分析等对所合成样品进行了表征.结果表明:在一定的高碱度条件下形成高浓度的硅铝酸盐凝胶,才能合成出晶化良好的样品,ZSM-5分子筛是按固相机理形成的;合成ZSM-5分子筛的相对结晶度和平均颗粒度均随晶化温度的升高及硅铝酸盐凝胶浓度的增加而增大,在室温陈化24 h、180℃晶化12～24 h时相对结晶度最高,平均颗粒度基本上与陈化时间无关.     

低成本原料一步直接合成小晶粒ZSM-5分子筛

以硫酸铝、水玻璃、正丁胺、水、晶种、NaCl、浓硫酸等低成本试剂为原料,一步直接合成法制备了高结晶度小晶粒ZSM-5分子筛,详细考察了凝胶陈化方式、滴加顺序、晶化时间、晶化温度、水量及原料硅铝比对分子筛结晶度及粒度的影响.通过XRD、SEM等对合成的分子筛进行了详细表征.研究结果表明:采用低温水浴回流搅拌陈化方式、在160～170℃、晶化30 h可获得高结晶度小晶粒ZSM-5分子筛.正反加顺序对分子筛结晶度影响不大.     

晶化条件对MnAPO-36分子筛合成的影响

以拟薄水铝石、质量分数85%的正磷酸、四水合醋酸锰为原料,三正丙胺为模板剂,采用原位水热法合成了MnAPO-36分子筛,利用FT-IR、SEM、XRD、TG-DSC及NH3-TPD等方法对MnAPO-36分子筛进行了表征.考察了晶化温度和晶化时间对原位水热法合成MnAPO-36的结晶度的影响.研究结果表明,用三正丙胺为模板剂在水热条件下制备MnAPO-36分子筛,容易共生MnAPO-5的晶型.采用先在100℃晶化50 h,然后在150℃晶化24 h的两步晶化方法,能得到纯度相对较高的MnAPO-36.     

低硅SAPO-34分子筛的复合模板剂法合成及其对甲醇制烯烃的催化性能

系统考察了模板剂比例和晶化条件对复合模板剂(三乙胺+四乙基氢氧化铵)法合成低硅SAPO-34分子筛的影响;评价了合成产物对甲醇制烯烃的催化性能.结果表明,190℃晶化时不易合成低硅SAPO-34分子筛,而170℃晶化、模板剂组成为2Et3N+0.3TEAOH时可合成纯相SAPO-34分子筛.较高温度晶化时,延长晶化时间,SAPO-34有向SAPO-5转晶的趋势,而较低温度晶化时则相反.与晶化3 d的分子筛样品相比,170℃晶化5 d后的分子筛样品的比表面积较大、强酸中心较多、弱酸中心较少、对甲醇制烯烃反应的催化寿命较长.     

高岭土微球上无胺法ZSM-5的原位合成

无胺体系中,采用水热法在焙烧高岭土微球上原位晶化合成了ZSM-5分子筛。考察了晶化温度、晶化时间、晶种加入量以及合成体系硅铝比等主要因素对分子筛合成的影响,得出了较佳的原位晶化合成条件。采用XRD、SEM、N₂吸附脱附等手段对合成样品进行了表征。结果表明：在高岭土微球上合成出了颗粒尺寸小于1 μm的小晶粒原位ZSM-5分子筛;晶化产物的比表面积、总孔容、微孔表面积和微孔孔容均明显增大,微孔分布集中于0.54 nm。     

动态水热合成b轴取向MFI型分子筛膜

在旋转烘箱中采用动态水热法,在不锈钢片支撑体上合成了连续的b轴取向MFI型分子筛膜,并运用扫描电镜和X射线衍射考察了合成釜转速、晶化温度和晶化时间对所得分子筛膜性能的影响.与静态水热法相比,动态水热合成过程中合成液的温差和浓度差大大降低,且合成液持续冲刷支撑体表面,使得动态法具有合成时间短、取向性好和分子筛颗粒粒径分布均一的优点.     

气相转移法合成ZSM-5/SAPO-5复合分子筛

以磷酸、拟薄水铝石和硅溶胶为原料, 三乙胺为模板剂, 采用气相转移法合成了一系列ZSM-5/SAPO-5复合分子筛. 产物经X射线衍射、扫描电镜、X射线能量散射谱、红外光谱及N2 静态吸附法等手段对其进行了表征, 证明合成材料是以ZSM-5为核、SAPO-5为壳的双结构分子筛. 实验结果表明, 干胶制备条件及液相组成都影响复合分子筛的结晶. 晶化温度的提高和晶化时间的延长有利于分子筛结晶度的提高. VPT法可以减小SAPO-5和复合分子筛颗粒的直径, 改善SAPO-5在ZSM-5分子筛表面的分布. 重油裂化结果表明, 核壳结构复合分子筛对生成低碳烯烃的性能优于机械混合的样品.     

ZSM-5、ZSM-57分子筛和丝光沸石间的转晶规律

考察了硅铝比、碱度、有机胺模板剂、晶化时间及温度等合成条件对ZSM-5、ZSM-57 分子筛和丝光沸石之间相互转晶的影响. 发现较高的碱度、较长的晶化时间有利于合成丝光沸石；较低的碱度、较高的诱导晶化温度、较长的晶化时间有利于合成低硅铝比的ZSM-57 分子筛；合成低硅铝比的ZSM-5分子筛则需要在能合成丝光沸石和ZSM-57 分子筛的碱度区间内精确调节碱度, 缩短晶化时间、降低诱导晶化温度、加入适当晶种, 有利于合成低硅铝比的ZSM-5 分子筛. 合成条件稍微改变, 会导致各种沸石之间发生转晶, 晶化产物出现两种或两种以上的晶型.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.