Structural and electronic relationships between conducting iron niobates and iron tungstates

Members of the system FeNbO and FeWO were compared, and their electronic properties were correlated with the structural parameters. The compounds crystallize as ordered variants of the basic α-PbO₂ structure, and the nature of the ordering of the [FeO₆] and [NbO₆] or [WO₆] octahedra determines the conductivity which may be observed for these phases.     

Structure,magnetic, and electrical properties of bismuth niobates doped with d-elements: VIII. Phase transitions and electrophysical properties of bismuth niobate

Reversible phase transitions of bismuth niobate Bi₃NbO₇ have been observed: from the lowtemperature cubic modification to the tetragonal one at 860°C and from the tetragonal modification to the hightemperature cubic one at 950–980°C. With increasing temperature of the cubic modification preparation, the unit cell parameter has been decreasing. Electrophysical properties of the cubic phases have matched at the frequencies below 1 kHz (up to 650 K). The specific conductivity of the tetragonal phase exceeds that of the cubic phase by no more than an order of magnitude (below 1000 K).     

Structure, magnetic, and electric properties of bismuth niobates doped with d elements: I. Magnetic behavior of chromium-containing solid solutions of low-and high-temperature bismuth orthoniobate

Magnetic susceptibility of solid solutions of bismuth orthoniobates of low-and high-temperature modifications containing chromium was studied. Parameters of exchange interactions in the dimeric clusters of nickel atoms and also the distribution of monomers and dimers in the solid solutions were calculated. The crystal structure of bismuth orthoniobate of the high-temperature modification is characterized by a greater tolerance to the formation of oxygen vacancies, resulting from heterovalent substitution.     

Structure, magnetic, and electric properties of bismuth niobates doped with d elements: II. State of nickel atoms in solid solutions of low-and high-temperature bismuth orthoniobate

The magnetic susceptibility of nickel-doped solid solutions of bismuth orthoniobate of the low-and high-temperature modifications was studied. Parameters of exchange interactions in dimeric clusters of nickel atoms and also the distribution of monomers and dimers in the solid solutions were calculated. The nickel-containing solid solutions of low-and high-temperature bismuth orthoniobate are similar in magnetic behavior.     

Structural characterization of amorphous and nanostructured bismuth silicate xerogels

Bismuth silicate xBi₂O₃·(1 − x)SiO₂ xerogels, 0 ≤ x ≤ 0.5, doped with gadolinium have been synthesized by sol–gel method. The study aims to evidence by X-ray diffraction (XRD), electron paramagnetic resonance (EPR) and nuclear magnetic resonance (NMR) the structural changes in amorphous Bi₂O₃–SiO₂ xerogels, function of Bi₂O₃ content and heat treatment. As was proved by XRD, nanostructured samples were obtained after 30 min heat treatment at 400 °C of the as-prepared samples with x > 0, in the mainly amorphous matrices nanocrystals of Bi_5.6Si_0.5O_9.4 phase being developed. The dimension of the nanocrystallites are function of the bismuth content, and vary from few nanometers to 25 nm for samples with x = 0.14 and x = 0.5 respectively. The local order around silicon, reflected by 29Si MAS NMR spectra, is less dependent on both composition and thermal history of the samples, showing that an amorphous silicon rich phase is present in all samples. The changes in the local order around Gd³⁺ ions, as reflected by the EPR spectra dependence on composition and especially on the heat treatment, support the assumption that a part of these paramagnetic ions is incorporated in the bismuth rich phase.     

Gas transport properties of substituted PEEKs

Tert-butyl and di-tert-butyl were added as pendant groups to the ether-ether phenyl ring of poly(ether ether ketone), PEEK. tert-butyl PEEK, TBPEEK, was amorphous and di-tert-butyl PEEK, DBPEEK, was semicrystalline. However, a 2 : 1 random copolymer of TBPEEK and DBPEEK, TBDBPEEK, was amorphous. Gas transport of N₂, O₂, CH₄, and CO₂ through amorphous films of PEEK, TBPEEK, TBDBPEEK, and tetramethylbiphenyl PEEK were determined at 35°C and at pressures to about 15 atm. The results support previous observations that tert-butyl and tetramethylbiphenyl groups are very effective in disrupting chain packing in the polymer. For the present polymers, these substitutions led to a 5–18-fold increase in permeability, and, in some cases, at no loss in permselectivity. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2355–2362, 1997     

Gas sorption and transport in substituted polystyrenes

The effects of pendant groups on gas transport were investigated using a series of substituted polystyrenes. Permeability coefficients were measured at 35°C and 1 atm for He, N₂, O₂, CH₄, and CO₂, and diffusion coefficients were calculated from time lag data. The absolute permeabilities for the polystyrenes are correlated reasonably well using a free volume model. All pendant group substitutions resulted in a reduction of the mobility selectivity for CO₂/CH₄ separation relative to polystyrene, although there was very little effect on the O₂/N₂ selectivity. The effects of the various substituents were individually analyzed in terms of their size, rigidity, and polarity. The addition of a methyl group to the backbone significantly decreases transport, while attachment to the para ring position increases permeation. Bulky rigid groups, such as t-butyl, enhance permeation even more. Methoxy and acetoxy substitutions provided an excellent means of examining plasticization of polymers by CO₂, such as cellulose acetate, which contain these same moieties. The response of these polymers indicates that the degree of plasticization is related to the polarity and flexibility of the pendant group.     

Gas sorption and transport in substituted polycarbonates

The effects of molecular structure manipulation of polycarbonates on sorption and transport of various gases were studied using tetramethyl, tetrachloro, and tetrabromo substitutions onto the aromatic rings of bisphenol A polycarbonate. Solubility and permeability measurements were made at 35°C over the pressure range of 1–20 atm for a variety of gases, namely CO₂, CH₄, O₂, N₂, and He. A threefold to fourfold increase in permeability was caused by the tetramethyl substitution, whereas the tetrachloro and tetrabromo substitutions reduced the permeability relative to the tetramethyl substitution. Lower activation energies for transport were found for the tetramethyl polycarbonate relative to the unsubstituted polycarbonate. Permeability coefficients were factored into solubility and diffusion coefficients. Sorption levels increased for all substitutions, but among the substituted polymers the levels remain practically the same. Solubility data were analyzed in terms of the dual sorption model. The Henry's law solubility coefficients obtained from this analysis were found to be consistent with a predictive equation developed for rubbery polymers. The usual correlation for predicting the Langmuir sorption capacity of the model overestimates the values for the substituted polycarbonates, and a proposal for the cause of this is offered. Thermal expansion of these polymers was measured using dilatometry, and the results are used in the interpretation of the sorption data. Diffusion phenomena are explained by segmental mobility and free volume considerations. The effects of CO₂ exposure history on sorption and transport were also investigated.     

Structural characterisation of the first mononuclear bismuth porphyrin

A single carboxylate picket bismuth porphyrin has been characterised in the solid state as the first instance of a non-dimeric structure; the carboxylate picket, bent over the macrocycle, is coordinated to the bismuth, inducing a significant distortion of the porphyrin core.     

Oxygen-ionic conductors based on substituted bismuth molybdates with column-type structural fragments

The possibility of synthesizing oxygen-ionic conductors from substituted bismuth molybdates containing [Bi₁₂O₁₄] _n ⁸ⁿ⁺ columns, MoO₄ tetrahedra, and isolated Bi ions in their structure was studied. The specifics of their structure and electric conductivity were investigated. The general formula of the solid solutions can be recorded as Bi₁₃Mo_{5 ? x} Me _x O_{34 ? δ}, where Me is the fouror five-valent d metal (Ti, Zr, V, Nb). The electric conductivity of doped bismuth molybdates considerably increased compared with that of the matrix compound. The electric conductivity reached 5.5 × 10^?3 S cm^?1 at 700°C and 1.8 × 10^?4 S cm^?1 at 350°C for the zirconium-doped compound with x = 0.4. The porosity of the ceramics was less than 5%; the thermal expansion coefficient was of the order of 14 × 10^?6 K^?1. Based on the set of their characteristics, these compounds are recommended as materials for membranes of electrochemical devices.     

Structural and transport characteristics of polyethylene oxide/phenolic resin blend solid polymer electrolytes

Details on the structure and transport characteristics of the solid polymer electrolyte polyethylene oxide (PEO)/lithium salt (LiClO₄) modified by novolac phenolic resin are presented here. From IR spectra it could be concluded that complex formation occurred through multiple interactions between the ether oxygen of PEO–lithium, phenolic lithium, and the phenolic ether oxygen of PEO. The free hydroxyl band in phenolic reflected that phenolic closely interacted with both the PEO polymer and ionic salt. With increasing salt content in PEO, the vibration band corresponding to the ClO anion (～623 cm^?1) displayed growth of a shoulder at ～635 cm^?1, suggesting the formation of Li⁺…ClO₄^? ion pairing. However, in the presence of phenolic, ion‐pairing formation was effectively suppressed, which suggested that the phenolic moiety facilitated a greater degree of LiClO₄ salt dissociation. Activation energy analysis revealed two conducting pathways: one through the amorphous PEO and the other through the PEO/phenolic amorphous matrix. The high ion conductivity originated from effective salt dissociation and the establishment of a new conduction network formed by PEO and phenolic. Furthermore, the structural modification also extended the thermal stability and mechanical strength of the solid polymer electrolyte composite. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3866–3875, 2004     

Structural and electrical properties of crystals of substituted polyaniline

The simultaneous polymerization and crystallization of aniline has been reported earlier. In this article, the X‐ray crystal structure analysis, SEM morphological analysis and electrical properties of such crystals of oligo‐polyanilines are being reported. The structural analysis shows a pseudo‐orthorhombic lattice. The SEM images reveal flaky and triangular growth habit with granular overgrowths on the surface. The bulk conductivities achieved vary from 10^?5 S/cm to 10^?7 S/cm as the oxidant concentration is reduced from 5 to 0.1%. The temperature dependence showed a transition point upto which there is a decrease in current and above which the current increases. The ESR studies reveal polarons involved in charge conduction and their concentration is proportional to the oxidant concentration. The X‐ray patterns, conductivities, and ESR results have been correlated with the degree of polymerization results obtained from GPC studies. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1127–1137, 2007     

Structural characterization of methanol substituted lanthanum halides

The first study into the alcohol solvation of lanthanum halide [LaX₃] derivatives as a means to lower the processing temperature for the production of the LaBr₃ scintillators was undertaken using methanol (MeOH). Initially the de-hydration of {[La(μ-Br)(H₂O)₇](Br)₂}₂ (1) was investigated through the simple room temperature dissolution of 1 in MeOH. The mixed solvate monomeric [La(H₂O)₇(MeOH)₂](Br)₃ (2) compound was isolated where the La metal center retains its original 9-coordination through the binding of two additional MeOH solvents but necessitates the transfer of the innersphere Br to the outersphere. In an attempt to in situ dry the reaction mixture of 1 in MeOH over CaH₂, crystals of [Ca(MeOH)₆](Br)₂ (3) were isolated. Compound 1 dissolved in MeOH at reflux temperatures led to the isolation of an unusual arrangement identified as the salt derivative {[LaBr_2.75·5.25(MeOH)]^+0.25 [LaBr_3.25·4.75(MeOH)]^−0.25} (4). The fully substituted species was ultimately isolated through the dissolution of dried LaBr₃ in MeOH forming the 8-coordinated [LaBr₃(MeOH)₅] (5) complex. It was determined that the concentration of the crystallization solution directed the structure isolated (4 concentrated; 5 dilute) The other LaX₃ derivatives were isolated as [(MeOH)₄(Cl)₂La(μ-Cl)]₂ (6) and [La(MeOH)₉](I)₃·MeOH (7). Beryllium Dome XRD analysis indicated that the bulk material for 5 appear to have multiple solvated species, 6 is consistent with the single crystal, and 7 was too broad to elucidate structural aspects. Multinuclear NMR (¹³⁹La) indicated that these compounds do not retain their structure in MeOD. TGA/DTA data revealed that the de-solvation temperatures of the MeOH derivatives 4–6 were slightly higher in comparison to their hydrated counterparts.     

Structural characterization of mono-ruthenium substituted Keggin-type silicotungstates

We have synthesized the mono-ruthenium substituted Keggin-type silicotungstate [SiW(11)O(39)Ru(III)(H(2)O)](5-) (1a) by reaction of the mono-lacunary silicotungstate precursor [SiW(11)O(39)](8-) with Ru(acac)(3) under hydrothermal conditions and isolated as the caesium salt Cs(5)[SiW(11)O(39)Ru(III)(H(2)O)] (1). The DMSO-coordinated complex [SiW(11)O(39)Ru(III)(DMSO)](5-) (2a) was prepared by reaction of 1a with DMSO in aqueous solution at 353 K and isolated as the caesium-potassium mixed salt Cs(4.9)K(0.1)[SiW(11)O(39)Ru(III)(DMSO)] (2). Both compounds 1 and 2 were characterized by single-crystal X-ray structure analysis, powder X-ray structure analysis, UV-Vis spectroscopy, cyclic voltammetry, IR-spectroscopy and elemental analysis. 1 crystallized in the tetragonal space group P4(2)/ncm with a = 20.9299(4), c = 10.3603(4) Angstrom, Z = 4. The ruthenium atom in the Keggin unit could not be distinguished from the tungsten due to disorder. The structural analysis of 2 (monoclinic, P2(1)/c, a = 13.5850(4), b = 20.2764(7), c = 18.1326(4) Angstrom, beta = 90.8730(10) degrees , Z = 4) successfully revealed that the incorporated ruthenium atom is coordinated by DMSO through a Ru-S bond. Polyanion 2a represents the first mono-substituted Keggin ion in which the ruthenium center is not crystallographically disordered. UV-Vis spectroscopy combined with controlled potential electrolysis confirmed that the incorporated rutheniums in 1 and 2 have a valence state of +3. The IR spectra of both 1 and 2 were very similar. All these data indicate that 1 synthesized by reaction of the mono-lacunary silicotungstate K(8)[SiW(11)O(39)] with Ru(acac)(3) under hydrothermal conditions is truly the mono-ruthenium substituted Keggin-type silicotungstate.     

Structural and optical properties of barium titanate modified bismuth borate glasses

Glass samples with composition (70B₂O₃–29Bi₂O₃–1Dy₂O₃) modified with Barium titanate (BT), where BT is added in different successive weight percents, have been synthesized by conventional melt quenching technique. X-ray diffraction studies were performed in order to confirm the amorphous nature of the samples. The density of the samples has been found to decrease with an increase in the BT content, whereas an opposite trend has been observed in the molar volume. The analysis of FTIR and Raman spectra of the samples depicts that the glass network is built up of mainly BiO₆, BiO₃, BO₃ and BO₄ units. Its detailed analysis also revealed that the glass structure depends upon the amount of BT in the glass matrix and hence it acts as a modifier in the glass network. Introduction of BT into the glass matrix leads to the conversion of BO₃ trigonal units into BO₄ tetrahedral units, which results in a decrease in the degree of disorder in the glass network and makes the glass system more stable. The values of Urbach energy obtained for the prepared samples also confirmed the decrease in disorder in the glass network. The optical absorption measurements carried out for well-polished samples show a decrease in optical band gap energy with an increase in BT content whereas the molar refractivity shows the reverse trend. The Hydrogenic excitonic model applied to the studied glasses suggested that the present glass system favors direct transitions. The metallization criterion of the presently studied samples suggests that the prepared glasses may be potential candidates for nonlinear optical applications.     

Structural and rate studies of the formation of substituted benzynes

The key elimination step for the formation of 3-substituted and 3,6-disubstituted benzynes from 2-haloaryllithiums displays a pronounced solvent-dependent regioselectivity. All 2-haloaryllithiums with electron withdrawing groups in the 6 position are shown by 6Li and 13C NMR spectroscopic studies to be monomers in THF. DFT computational studies implicate trisolvates. Rate studies reveal that LiF eliminates via monomer-based pathways requiring THF dissociation whereas LiCl eliminates via nondissociative pathways. Elimination to form 3-chloro- and 3-fluorobenzyne from 2-chloro-6-fluorophenyllithium displays a pronounced solvent-dependent regioselectivity that is traced to competing solvent-dissociative and nondissociative dissociative pathways for the elimination of LiCl and LiF, respectively.     

Oxygen nonstoichiometry and transport properties of strontium substituted lanthanum ferrite

This study presents an investigation of the properties of (La_0.6Sr_0.4)_0.99FeO_3-δ (LSF40) covering thermomechanical properties, oxygen nonstoichiometry and electronic and ionic conductivity. Finally, oxygen permeation experiments have been carried out and the oxygen flux has been determined as a function of temperature and driving force.The electrical conductivity was measured using a 4 probe method. It is shown that the electrical conductivity is a function of the charge carrier concentration only. The electron hole mobility is found to decrease with increasing charge carrier concentration in agreement with recent literature.Values of the chemical diffusion coefficient, D_Chem, and the surface exchange coefficient, k_Ex, have been determined using electrical conductivity relaxation. At D_Chem is determined to be with an activation energy of . The surface exchange coefficient is found to decrease with decreasing oxygen partial pressure.Oxygen permeation experiments were carried out. The flux through a membrane placed between air and wet hydrogen/nitrogen was (corresponding to an equivalent electrical current density of ). The oxygen permeation measurements are successfully interpreted based on the oxygen nonstoichiometry data and the determined transport parameters.     

Structural and electronic properties of amorphous bismuth calcium borate from first-principle calculations

Structural Chemistry - We investigatethe electronic and structural properties of two new amorphous materials, Bi6Ca2O28B12 and Bi6Ca2 O28B11:Tm, using density functional theory with a short-range...     

Structural properties and potential reactivity of substituted 3- aroyldithiocarbazates

A series of substituted 3-aroyldithiocarbazates has been synthesized and studied. The corresponding acid dissociation constants have been determined potentiometrically. Semiempirical PM3 molecular orbital calculations suggest the existence of several tautomeric forms of the compounds. Geometrical parameters, proton affinities, and static reactivity indices have been examined. Structural properties and protonation sites are well described by calculations. The strong correlations between the pK _a values and the Hammett constants as well as the N(3) calculated proton affinities indicate that the N(3) atom is the most probable protonation site. The thermodynamics of the protonation process are mainly controlled by HOMO-LUMO rather than electrostatic interactions. According to PM3 results, 3-aroyldithiocarbazic acid should be quite stable in the gas phase, while a mechanism for its decomposition in solution is proposed.