Pt—TiO2光催化还原罗丹明B

报道了罗丹明B（RhB)在TiO2催化剂上的吸附过程及加氢反应结构。当草酸作为电给体时,光催化反应产生的氢气,可使RhB发生快速地氢反应,生成无色的加氢产物。该加氢过程与催化剂的种类、表面化学状态和担载催化剂的种类有密切关系。     

污染物甲醛为电子给体Pt/TiO2光催化制氢

研究了甲醛为电子给体在Pt/TiO2上光催化生成氢的反应。甲醛经光催化降解产生CO2和甲酸，甲酸可进一步被氧化；甲醛的光催化降解与放氢同时发生，催化剂的最佳Pt负载量为0．5％，甲醛浓度对反应的影响，表观上符合Langmuir-Hinshelwood关系式；碱性条件有利于该反应；在甲醛浓度较低时，甲醇的存在能部分地提高放氢速率，并讨论了可能的反应机理。     

Pt/TiO2光催化重整降解2-氯乙醇水溶液制氢

在无氧条件下,进行了Pt担载的TiO2光催化有毒的2-氯乙醇(下文简称氯乙醇)重整制氢反应的研究.详细讨论了动力学因素如催化剂表面Pt化学状态、Pt担载量、溶液pH值、氯乙醇浓度等对产氢速率的影响,并用XRD、HNMR、XPS等技术进行了表征,探讨了氯乙醇降解和产氢反应机理.研究表明,在光催化降解氯乙醇的同时产生氢是完全可行的.催化剂表面的Pt以Pt0的化学状态存在,有利于析氧;溶液pH值对产生速率影响也很大,而氯乙醇的浓度变化只是在开始略有影响,浓度的增加对产氢并没有明显的影响.研究得出Pt担载的TiO2光催化重整氯乙醇制氢反应的最佳条件是Pt的最佳担载量约为1.0%;氯乙醇溶液浓度范围为0.04～0.10 M;最佳溶液pH值范围为4～10.     

紫外光致活的Pt／TiO2对苄醇催化自氧化反应的研究

本文主要研究了紫外光照致活的掺铂n型半导体氧化物催化剂(Pt/TiO_2)对苄醇进行催化自氧化的反应,依据光电导、PZC、表面组成、反应活性等实验结果,提出了反应机理及其单光子作用模型。     

羧基功能化石墨烯增强TiO2光催化产氢性能

The use of semiconductor photocatalysts (CdS, g-C₃N₄, TiO₂, etc.) to generate hydrogen (H₂) is a prospective strategy that can convert solar energy into hydrogen energy, thereby meeting future energy demands. Among the numerous photocatalysts, TiO₂ has attracted significant attention because of its suitable reduction potential and excellent chemical stability. However, the photoexcited electrons and holes of TiO₂ are easily quenched, leading to limited photocatalytic performance. Furthermore, graphene has been used as an effective electron cocatalyst in the accelerated transport of photoinduced electrons to enhance the H₂-production performance of TiO₂, owing to its excellent conductivity and high charge carrier mobility. For an efficient graphene-based photocatalyst, the rapid transfer of photogenerated electrons is extremely important along with an effectual interfacial H₂-production reaction on the graphene surface. Therefore, it is necessary to further optimize the graphene microstructures (functionalized graphene) to improve the H₂-production performance of graphene-based TiO₂ photocatalysts. The introduction of H₂-evolution active sites onto the graphene surface is an effective strategy for the functionalization of graphene. Compared with the noncovalent functionalization of graphene (such as loading Pt, MoS_x, and CoS_x on the graphene surface), its covalent functionalization can provide a strong interaction between graphene and organic molecules in the form of H₂-evolution active sites that are produced by chemical reactions. In this study, carboxyl-functionalized graphene (rGO-COOH) was successfully modified via ring-opening and esterification reactions on the TiO₂ surface by using an ultrasound-assisted self-assembly method to prepare a high-activity TiO₂/rGO-COOH photocatalyst. The Fourier transform infrared (FTIR) spectra, X-ray photoelectron spectroscopy (XPS), and thermogravimetric (TG) curves revealed the successful covalent functionalization of GO to rGO-COOH by significantly enhanced ―COOH groups in FTIR and increased peak area of carboxyl groups in XPS. A series of characterizations, including X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), XPS, and UV-Vis adsorption spectra, were performed to demonstrate the successful synthesis of TiO₂/rGO-COOH photocatalysts. The experimental data for the hydrogen-evolution rate showed that the TiO₂/rGO-COOH displayed an extremely high hydrogen-generation activity (254.2 μmol∙h⁻¹∙g⁻¹), which was 2.06- and 4.48-fold higher than those of TiO₂/GO and TiO₂, respectively. The enhanced photocatalytic activity of TiO₂/rGO-COOH is ascribed to the carboxyl groups of carboxyl-functionalized graphene, which act as effective hydrogen-generation active sites and enrich hydrogen ions owing to their excellent nucleophilicity that facilitates the interfacial hydrogen production reaction of TiO₂. This study provides novel insights into the development of high-activity graphene-supported photocatalysts in the hydrogen-generation field.      

Pt/TiO2光诱导催化重整乙醇制氢

对无氧条件下Pt/TiO2光诱导催化重整乙醇制氢进行了系统的研究，结果表明，乙醇的光催化重整制氢反应受催化剂表面化学状态，反应体系的pH值，浓度的影响较大，而受反应体系温度的影响较小，在运动XRD，XPS，HNMR等技术手段对催化剂和反应产物进行表征，分析的基础上，提出了无氧条件下乙醇光催化重整制氢可能的反应机理。     

无氧条件下Pt/TiO_2光催化重整降解—乙醇胺水溶液制氢

以-乙醇胺(以下简称乙醇胺)为电子给体,在无氧条件下进行了Pt/TiO2光催化重整制氢的研究.详细讨论了诸多因素如催化剂表面Pt化学状态、Pt担载量、溶液pH值、乙醇胺溶液浓度等对产氢效率的影响,并用XRD、HNMR、XPS等进行了深入表征,探讨了Pt/TiO2光催化重整降解乙醇胺和产氢的反应,实验表明,利用所制备的光催化剂,可实现在消除水中有机污染物的同时制取氢气的目标.催化剂表面的Pt以Pt0的化学状态存在,有利于析氢;溶液pH值和浓度的变化对产生速率也有一定的影响.同时发现Pt/TiO2光催化重整乙醇胺制氢反应的最佳条件是:Pt的最佳担载量约为0.5％-1.0％;乙醇胺溶液最佳浓度约为0.05 mol·L-1;最佳溶液pH值范围为4-10;氨基取代的羰基类化合物是其主要中间产物.     

Pt/TiO2光催化甲烷重整水气制氢

在室温下以太阳能替代传统的高温高压热反应条件,在固定床装置中实现连续动态光催化甲烷重整水气(PSRM)制氢反应:CH4+2H2O(g)→4H2+CO2. 产物的主成分是H2和CO2,同时检测到微量或痕量的C2H6、C2H4和CO. 重点考察了以光沉积法负载Pt的TiO2(p-Pt/TiO2)为光催化剂,该反应体系在不同CH4/H2O进料摩尔比、进料的总流速、光照波长、催化剂用量以及贵金属的负载方式等的实验条件对氢气产率的影响. 最优化的反应条件为:CH4/H2O进料摩尔比为4; 进料总流速为0.5 mL.min-1; 光沉积负载要优于浸渍法; 相同的负载方式Pd和NiOx为比较优异的助催化剂; 最佳催化剂用量为20 mg.cm-2. 最后循环实验结果表明,p-Pt/TiO2及反应体系都具有比较高的稳定性.     

Visible Light Photocatalytic Activity of Pt/N‐TiO2 towards Enhanced H2 Production from Water Splitting

Present work mainly focuses on experimental investigation to improvement of hydrogen production by water photoelectrolysis. An experimental facility was designed and constructed for visible light photocatalysis. A series of N‐TiO₂ photocatalysts impregnated with platinum on the surface of N‐TiO₂ were prepared. Hydrogen production upon irradiating aqueous Pt/N‐TiO₂ suspension with visible light was investigated. The shift in excitation wavelength of TiO₂ was 380 nm improved the yield of hydrogen production by N‐TiO₂ and Pt/N‐TiO₂. We used a 400 W mercury arc lamp combined with a 400 nm cutoff filter eliminating all the wavelengths under 400 nm. Pt/N‐TiO₂ material was characterized with TPR, reflective UV/Visible spectroscopy and TEM. The best hydrogen production rate obtained for this setup for N/Ti = 10, 0.05 wt% Pt/N‐TiO₂, through water splitting was about 772 μmolh^?1g^?1.     

无氧条件下Pt/TiO2光催化重整降解一乙醇胺水溶液制氢

以一乙醇胺（以下简称乙醇胺）为电子给体,在无氧条件下进行了Pt/TiO2光催化重整制氢的研究.详细讨论了诸多因素如催化剂表面Pt化学状态、Pt担载量、溶液pH值、乙醇胺溶液浓度等对产氢效率的影响,并用XRD、HNMR、XPS等进行了深入表征,探讨了Pt/TiO2光催化重整降解乙醇胺和产氢的反应, 实验表明,利用所制备的光催化剂, 可实现在消除水中有机污染物的同时制取氢气的目标.催化剂表面的Pt以Pt0的化学状态存在, 有利于析氢;溶液pH值和浓度的变化对产生速率也有一定的影响.同时发现Pt/TiO2光催化重整乙醇胺制氢反应的最佳条件是:Pt的最佳担载量约为0.5％～1.0％;乙醇胺溶液最佳浓度约为0.05 mol•L－1;最佳溶液pH值范围为4～10;氨基取代的羰基类化合物是其主要中间产物.     

MoS_2/TiO_2复合催化剂的制备及其在紫外光下的光催化制氢活性

为了研究复合光催化剂在光催化中的制氢效率,采用水热法制备了Mo S2纳米片,然后通过水热法在Mo S2纳米片上负载了TiO_2纳米颗粒,形成了Mo S2/TiO_2异质结复合催化剂。采用冷场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)、紫外-可见吸收光谱(UV-Vis)、拉曼光谱(Raman),X射线光电子能谱(XPS)对材料的结构和光学性能表征并进行分析。通过光催化制氢测试对光催化剂进行评价,实验结果表明,在波长为365 nm的紫外光照射下,最高光催化制氢速率为1004μmol·h-1·g-1,对应的催化剂的Mo S2含量为30%,其催化速率远大于单一的Mo S2和TiO_2,表明Mo S2/TiO_2复合催化剂在紫外光照下能显著提高光催化产氢性能。基于Mo S2/TiO_2复合光催化剂优越的光催化产氢性能,本文对复合光催化剂的产氢机理做了研究和分析。     

TiO2负载Pt对光催化去除低浓度NO性能的影响

以溶胶-凝胶法以及湿式浸渍法制备了Pt/TiO2催化剂,采用了XRD、BET、UV-vis、TEM、XPS等方法进行表征,并进行了对NO的催化氧化性能测试.结果表明铂的负载能显著提高TiO2光催化剂对NO的氧化转化能力和去除率.0.5%Pt/TiO2对NO的氧化率与去除率分别为45.0%和38.1%,与纯锐钛矿TiO2(13.6%,10.7%)相比,氧化效率提高3.3倍,去除效率提高3.6倍.通过比较不同方法制备的负载Pt催化剂的活性,初步讨论了催化剂表面发生的反应机理:铂氧化物以及催化剂表面吸附的O2分子通过与光生电子和光生空穴结合,产生了强氧化性自由基,将NO氧化得到NO2.     

A Dewetted‐Dealloyed Nanoporous Pt Co‐Catalyst Formed on TiO2 Nanotube Arrays Leads to Strongly Enhanced Photocatalytic H2 Production

Pt nanoparticles are typically decorated as co‐catalyst on semiconductors to enhance the photocatalytic performance. Due to the low abundance and high cost of Pt, reaching a high activity with minimized co‐catalyst loadings is a key challenge in the field. We explore a dewetting‐dealloying strategy to fabricate on TiO₂ nanotubes nanoporous Pt nanoparticles, aiming at improving the co‐catalyst mass activity for H₂ generation. For this, we sputter first Pt‐Ni bi‐layers of controllable thickness (nm range) on highly ordered TiO₂ nanotube arrays, and then induce dewetting‐alloying of the Pt‐Ni bi‐layers by a suitable annealing step in a reducing atmosphere: the thermal treatment causes the Pt and Ni films to agglomerate and at the same time mix with each other, forming on the TiO₂ nanotube surface metal islands of a mixed PtNi composition. In a subsequent step we perform chemical dealloying of Ni that is selectively etched out from the bimetallic dewetted islands, leaving behind nanoporous Pt decorations. Under optimized conditions, the nanoporous Pt‐decorated TiO₂ structures show a>6 times higher photocatalytic H₂ generation activity compared to structures modified with a comparable loading of dewetted, non‐porous Pt. We ascribe this beneficial effect to the nanoporous nature of the dealloyed Pt co‐catalyst, which provides an increased surface‐to‐volume ratio and thus a more efficient electron transfer and a higher density of active sites at the co‐catalyst surface for H₂ evolution.     

Kinetics of Photogenerated Electrons Involved in Photocatalytic Reaction of Methanol on Pt/TiO2

Time-resolved IR spectroscopy was used to detect the photocatalytic reaction of methanol for H2 production on Pt/TiO2 catalysts. There exists an optimal amount of Pt loading in the Pt/TiO2 catalysts for the reaction of the photogenerated long-lived electrons. For a given amount of Pt loading, the reaction rate of the long-lived electrons on Pt/TiO2 catalysts varies greatly with the di?erent reduction temperature of the catalysts. The possible reason is that the Pt particles occupy the surface active sites for methanol adsorption on Pt/TiO2 catalysts reduced at high temperature. This phenomenon is not observed obviously on Pt/TiO2 catalysts reduced at low temperature. The decay rate of the long-lived electrons evaluated by time-resolved IR method qualitatively correlates well with the activity of H2 production under steady-state irradiation conditions.