Plastic supported platinum modified nickel electrode and its high electrocatalytic activity for sodium borohydride electrooxidation

A novel plastic/multi-walled carbon nanotube(MWNTs)-nickel(Ni)-platinum(Pt) electrode(PMNP) is prepared by chemical-reducing Pt onto the surface of Ni film covered plastic/MWNTs(PM) substrate. The MWNTs are adhered by a piece of commercial double faced adhesive tape on the surface of plastic paper and the Ni film is prepared by a simple electrodeposition method. The morphology and phase structure of the PMNP electrode are characterized by scanning electron microscopy,transmission electron microscope and X-ray diffractometer. The catalytic activity of the PMNP electrode for Na BH4 electrooxidation is investigated by means of cyclic voltammetry and chronoamperometry. The catalyst combines tightly with the plastic paper and exhibits a good stability. MWNTs serve as both conductive material and hydrogen storage material and the Ni film and Pt are employed as electrochemical catalysts. The PMNP electrode exhibits a high electrocatalytic performance and the oxidation current density reaches to 10.76 A/(mg·cm) in 0.1 mol/dm3 Na BH4at0 V,which is much higher than those in the previous reports. The using of waste plastic reduces the discarding of white pollution and consumption of metal resources.     

Electrochemical sensing of DNA immobilization and hybridization based on carbon nanotubes/nano zinc oxide/chitosan composite film

A novel electrochemical DNA biosensor based on zinc oxide （ZnO） nanoparticles and multi-walled carbon nanotubes （MWNTs） for DNA immobilization and enhanced hybridization detection is presented. The MWNTs/nano ZnO/chitosan composite film modified glassy carbon electrode （MWNTs/ZnO/CHIT/GCE） was fabricated and DNA probes were immobilized on the electrode surface. The hybridization events were monitored by differential pulse voltammetry （DPV） using methylene blue （MB） as an indicator. The sensor can effectively discriminate different DNA sequences related to PAT gene in the transgenic corn, with a detection limit of 2.8× 10^-12 mol/L of target sequence.     

铁氰化锰修饰玻碳电极的制备及其电化学性能

A thin film of manganese hexacyanoferrate （MnHCF） was electrochemically formed on a glassy carbon （GC） electrode to prepare a chemically modified electrode （CME）. The mechanism of film formation of MnHCF and its growth process were investigated in detail by cyclic voltammetry. The results show that the stoichiometric composition of MnHCF is Mn^ⅢFe^Ⅲ（CN）6, an analogue of prussian yellow. There exist three clear-cut stages in the whole modification process and the last stage is indispensable to the fabrication of homogenized, stable MnHCF film and must last for an appropriate time. The surface morphology of MnHCF/GC electrode was characterized by scanning electron microscopy （SEM）, which further verified the effective deposition of MnHCF film on GC. The kinetic constants of MnHCF/GC electrode process were also evaluated. The resulting MnHCF film modified electrode presented good stability and high electrocatalytic activity toward the oxidation of H2O2, indicating that MnHCF film possesses function of catalase and can be expected for analytical purposes.     

Chemoselective hydrogenolysis of tetrahydrofurfuryl alcohol to 1,5-pentanediol over Ir-MoOx/Si02 catalyst

In this work, MoOx promoted Ir/SiO2 catalysts were prepared and used for the selective hydrogenolysis of tetrahydrofurfuryl alcohol （THFA） to 1,5-pentanediol in a continuous flow reactor. The effects of different noble metals （Ir, Pt, Pd, Ru, Rh）, supports and Ir contents were screened. Among the investigated catalysts, 4 wt%Ir-MoOx/SiO2 with a Mo/Ir atomic ratio of 0.13 exhibited the best catalytic performance. The synergy between Ix particles and the partially reduced isolated MoOx species attached on them is essential for the excellent catalytic performance of Ix-MoOx/SiO2. The catalyst exhibited a better hydrogenolysis efficiency of THFA with the selectivity of 1,5-pentanediol of 65%-74% at a conversion of THFA of 70%-75% when the initial THFA concentration is ranging from 20 wt% and 40 wt%. And higher system pressure was also in favor of the conversion of THFA. During a stability test, the conversion of THFA and 1,5-pentanediol yield over Ix-MoOz/SiO2 decreased with reaction time, which can be explained by the leaching of Mo species during the reaction.     

On the formation of the interlayer between Ni-P coating and AZ33 magnesium alloy substrate by means of in situ SEM observation

Pre-treatment process is the key step for electroless plating. Once a suitable pre-treatment film is in place, the desired metals can be plated. In this paper, Ni-P coating was successfully prepared on AZ33 magnesium alloy with Mg（OH）2 pre-treatment film by electroless plating. To investigate the role of MgF2 in Ni-P coating, the deposition procedures between Mg（OH）2 pre-treatment film and Mg（OH）2-MgF2 pre-treatment film （a traditional process） were compared. The surface morphology variations of coatings were observed with scanning electron microscopy and the compositions were analyzed by energy dispersive spectrometry. The results showed that during the plating, both MgF2 and Ni-P deposited at the initial stage, and MgF2 distributed in the bottom of the coating, forming a transitional interlayer with Ni- P. According to the heat quench test, a poor adhesion of the coating mainly occurred between the MgF2 and Ni-P coating.     

Corrosion of Nickel-based Alloy G30 in the Stratum Water Containing H2S/CO2

The influences of temperature and CO2 pressure on the corrosion of nickel-based alloy G30 in the stratum water containing H2S/CO2 were investigated with the aid Mott-Schottky analysis and scanning electron microscopy（SEM） of electrochemical impedance spectroscopy（EIS）, The results indicate that alloy G30 is in the passive state in the stratum water, which is related to the formation of the passive film on its surface. This passive film can significantly protect the substrate from further corrosion. And the film protection is enhanced with decreasing temperature and CO2 pressure. Auger electron spectrometry（AES） and X-ray photoelectron spectrometry（XPS） results reveal that the passive film shows the double-layer structure, i.e. the inner chromium oxide and the outer iron/nickel spinel oxides or hydroxides with Mo oxides dispersing throughout the inner and outer scale.     

The electrochemiluminescent behavior of nickel phthalocyanine（NiTSPc）/H2O2 system on a heated ITO electrode

In this study,the electrochemiluminescent（ECL） behavior of Nickel（Ⅱ） tetrasulfophthalocyanine（NiTSPc）/H₂O₂ on a heated indium tin oxide（ITO） electrode was investigated.The effect of pH value,electrochemical scan mode,concentration of NiTSPc and electrode surface temperature on the ECL intensities had been studied in detail.Based on the fact that the ECL of NiTSPc can be greatly enhanced by hydrogen peroxide at the ITO electrode,a new ECL biosensor for hydrogen peroxide has been developed.The possible mechanism for the ECL of NiTSPc has also been proposed.     

Detection and Theoretical Study of Fukui Function of Nitroaromatics by Carbazole-Based Iridium（Ⅲ）Phosphorescent Probe北大核心CSCD

A room temperature phosphorescent Ir（Ⅲ）complex Ir（ppyCz）3 is synthesized by a two-step synthesis method with a carbazole modified organic ligand. The high-efficiency luminescent detection strategy of six familiar nitroaromatics including 1,3-dinitrobenzene,etc. is developed using Ir（ppyCz）3 as the luminescent probe. The highest detection efficiency of 1,3-dinitrobenzene by Ir（ppyCz）3 is demonstrated with the quenching content KSV of（26. 38±1. 05）L/mmol,and minimum detection limit of 2. 50×10−6 mmol/L. Density functional theory calculations and spectral overlap experiments show that the detection mechanism of Ir（ppyCz）3 for the six nitroaromatics is assigned to electron transfer. The sequence of the orbital weighted Fukui function for the six nitroaromatics dovetails with the corresponding detection efficiency sequence of nitroaromatics by Ir（ppyCz）3. © 2022, Science Press (China). All rights reserved.     

Electrochemiluminescence of metal-organic complex nanowires based on graphene-Nafion modified electrode for biosensing application

In this work, we chose tris(2,2′-bipyridyl)ruthenium(II)hexafluorophosphate(Ru(bpy)3(PF6)2), a metal-organic complex material,to prepare nanowires, which were subsequently applied for the construction of electrochemiluminescence(ECL) biosensor by immobilizing them onto a glassy carbon electrode(GCE) with graphene-Nafion composite films. The graphene therein, being a two-dimensional carbon nanomaterial with outstanding electronic properties, can obviously improve the conductivity of the Nafion film, as well as enhance the electrochemical signal and ECL intensity of the Ru(bpy)3(PF6)2 nanowires(RuNWs) at low graphene concentration. The developed biosensor exhibited excellent ECL stability with tripropylamine(TPrA) as co-reactant. The ECL biosensor exhibited high sensitive ECL response in a wide linear range and low detection limit for the detection of proline. It is considered that the oxidation products of proline would be responsible for the ECL enhancement. The large electro-active area of the nanowires and the enhancement effect of the graphene played critical roles in the high detection performance of the ECL biosensor. The results demonstrated herein may provide a useful enlightenment for the design of more sensitive ECL biosensors.     

In situ Molecular Self-assembly and Sensitive Label-free Detection of Streptavidin via a Wavelength Interrogated Surface Plasmon Resonance Sensor

The sensing sensitivity of wavelength interrogated surface plasmon resonance（WISPR） biosensor is improved by self-assembly of polyelectrolyte multilayer（PEM） film of poly（allylamine hydrochloride）（PAH）/ poly（sodium-p-styrenesulfonate）（PSS） on the Au film coated glass chip via the layer-by-layer（LBL） technique. The home-made WISPR with Krestchmann configuration consists of a tungsten-halogen lamp as a photon source and a charge coupled device（CCD） camera as the detector. The influence of PEM film thickness on the optical properties of WISPR biosensors was investigated theoretically and experimentally. In order to achieve higher sensing sensitivity, the PEM film thickness has to be designed as ca.14 nm at an Au layer thickness of 50 nm and an incidental angle of 11.8°. Furthermore, the PEM coated WISPR biosensor can serve as highly sensitive biosensor, in which the biotin-streptavidin is used as bioconjugate pair. After deposition of the PEM film of （biotin/PAH）（PSS/PAH）3, the modified WISPR biosensor is more sensitive to the low concentration（〈0.01 mg/mL） of streptavidin. And the sensing sensitivity can be further increased by one order of magnitude compared with that of the biotin/PAH coated WISPR biosensor. Thus, such low-cost, high-performance and efficient PEM-coated WISPR biosensors have great potentials in a diverse array of fields such as medical diagnostics, drug screening, food safety analysis, environmental monitoring, and homeland security.     

Solid-state electrochemiluminescence of a novel iridium(Ⅲ) complex

The sofid-state ECL behavior of a water-insoluble bis-cyclometalated (pq)2Ir(N-phMA) complex is presented, in which pq is a 2-phenylquinoline anion and N-phMA is N-phenyl methacrylamide, a monoanionic bidentate ligand. The MWNTs/(pq)2Ir(N-phMA) film, MWNTs/Ru(bpy)32+ film and (pq)2Ir(N-phMA) directly modified glassy carbon electrode were fabricated; only the MWNTs/(pq)2Ir(N-phMA) film can produce steady ECL in the presence of tri-n-propylamine as a coreactant.     

Electrochemiluminescence (ECL) Detection of Ammonium Ion Based on a Novel Iridium Complex Modified Electrode

We report that ammonium ion, as its organic amine counterparts, can be sensitively detected as a coreactant in the electrochemiluminescence (ECL) reaction of a novel iridium complex (pq)₂Ir(N-phMA), where pq is 2-phenylquinoline anion and N-phMA is N-phenylmethacrylamide. The modified ECL electrode was fabricated by casting deposition of a homogeneous MWNTs/PVA/(pq)₂Ir(N-phMA) dispersion solution onto the surface of a glassy carbon electrode. The electrode responds sensitively to ammonium ion in a wide concentration range. Two regression equations were established: Y = 0.7016X + 46.8 (R² = 0.9985) and Y = 0.2565X + 174.2 (R² = 0.9991) for the concentration from 1–180 nM and 180–1800 nM, respectively. The limit of detection was as low as 0.13 nM (S/N = 3).     

Enhanced Electrochemiluminescence from a Stoichiometric Ruthenium(II)–Iridium(III) Complex Soft Salt

Electrochemiluminescence (ECL) and electrochemistry are reported for a heterometallic soft salt, [Ru(dtbubpy)₃][Ir(ppy)₂(CN)₂]₂ ( [Ir][Ru][Ir] ), consisting of a 2:1 ratio of complementary charged Ru and Ir complexes possessing two different emission colors. The [Ru]²⁺ and [Ir]^? moieties in the [Ir][Ru][Ir] greatly reduce the energy required to produce ECL. Though ECL intensity in the annihilation path was enhanced 18× relative to that of [Ru(bpy)₃]²⁺, ECL in the co‐reactant path with tri‐n‐propylamine was enhanced a further 4×. Spooling spectroscopy gives insight into ECL mechanisms: the unique light emission at 634 nm is due to the [Ru]²⁺* excited state and no [Ir]^?* was generated in either route. Overall, the soft salt system is anticipated to be attractive and suitable for the development of efficient and low‐energy‐cost ECL detection systems.     

Evaluation of electrogenerated chemiluminescence from a neutral Ir(III) complex for quantitative analysis in flowing streams

Though recently Ir(III) complexes have attracted much interest in electrochemiluminescent (ECL) analysis due to their high emission in various wavelengths, there were a few studies reported on its analytical applications. In this study, we evaluate the ECL from (pq)(2)Ir(acac) (pq = 2-phenylquinolate, acac = acetylacetonate) for the use in flow injection analysis. An aqueous solution of the analyte and (pq)(2)Ir(acac) passes through the reaction/observation cell, and then ECL reaction is generated by electrochemical initiation on the analyte and (pq)(2)Ir(acac). Tri-n-propylamine (TPrA) is used as a representative analyte for evaluation. Additionally, a comparison is made of the relative ECL intensities obtained for a variety of analytes including oxalate, amino acids, aliphatic amines, and NADH. The (pq)(2)Ir(acac) produces efficient ECL upon TPrA exhibiting the limit of detection of 5 nM with a linear range of 3 orders of magnitude in concentration whereas 20 nM is observed in the conventional Ru(bpy)(3)(2+) system. It shows particular sensitivity advantages for oxalate, proline, and tartaric acid. The ECL generation upon various analytes proposes direct applicability of (pq)(2)Ir(acac) as a post-column detection tool.     

Tris(2,2'-bipyridyl)ruthenium(II) electrochemiluminescence sensor based on carbon nanotube/organically modified silicate films

In this paper, a novel electrochemiluminescence (ECL) sensor was constructed to determine herring sperm (HS) double-stranded (ds) DNA. Tetramethoxysilane and dimethyldimethoxysilane were selected as co-precursors to form an organically modified silicate (ORMOSIL) film for the immobilization of multiwall carbon nanotubes (MWNTs) wrapped by poly(p-styrenesulfonate) (PSS), and then Tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) was successfully immobilized on a glassy carbon electrode via ion-association. PSS was employed to increase the conductivity of the ORMOSIL film and disperse the cut MWNTs, which were cut and shortened in a mixture of concentrated sulfuric and nitric acids, in the film. It was found that MWNTs could adsorb Ru(bpy)₃²⁺ and acted as conducting pathways to connect Ru(bpy)₃²⁺ sites to the electrode. MWNTs also played a key role as materials for the mechanical and thermal properties. The ECL performance of this modified electrode was evaluated in a flow injection analysis (FIA) system, and the detection limit (S/N = 3) for HS ds-DNA was 2.0 × 10⁻⁷ g mL⁻¹ with a linear range from 1.34 × 10⁻⁶ to 6.67 × 10⁻⁴ g mL⁻¹ (R² = 0.9876). In addition, the ECL sensor presented excellent characteristics in terms of stability, reproducibility and application life.     

Electrochemiluminescence Studies of Phosphorescent Dopant and Host Molecules of Polymer Light-emitting Diodes

Electrochemiluminescence (ECL) from tris(2‐phenylpyridine)irdium [Ir(ppy)₃] was investigated following cross reaction of its anion with oxidized poly(N‐vinyl‐carbazole) (PVK) and its cation with reduced 2‐(4‐biphenylyl)‐5‐(4‐tert‐butyl‐phenyl)‐1,3,4‐oxadiazole (PBD). Both cross reactions show Ir(ppy)₃ emission and the cross reaction of PVK^+·/Ir(ppy)⁻₃ showed the highest ECL intensity. The comparisons of the reaction enthalpy and the energy of Ir(ppy)₃ light emitting shows that reaction between PVK^+· and Ir(ppy)⁻₃ is energy sufficient to populate metal‐to‐ligand charge transfer (MLCT) excited singlet (3.04 eV) of Ir(ppy)₃, while the reaction between Ir(ppy)⁺₃ and PBD^{− ·} is energy efficient to populate MLCT excited triplet (2.4 eV). The ECL result in solution reveals that the energy released from charge transfer between the Ir(ppy)₃ and PVK or PBD is sufficient to produce the excited state of Ir(ppy)₃ in solid polymer light‐emitting diodes (PLEDs) based on PVK:PBD hosts doped by Ir(ppy)₃. These results obtained will provide further insight into charge‐transfer excitation in PLEDs.     

Understanding Electrogenerated Chemiluminescence Efficiency in Blue‐Shifted Iridium(III)‐Complexes: An Experimental and Theoretical Study

Compared to tris(2‐phenylpyridine)iridium(III) ([Ir(ppy)₃]), iridium(III) complexes containing difluorophenylpyridine (df‐ppy) and/or an ancillary triazolylpyridine ligand [3‐phenyl‐1,2,4‐triazol‐5‐ylpyridinato (ptp) or 1‐benzyl‐1,2,3‐triazol‐4‐ylpyridine (ptb)] exhibit considerable hypsochromic shifts (ca. 25–60 nm), due to the significant stabilising effect of these ligands on the HOMO energy, whilst having relatively little effect on the LUMO. Despite their lower photoluminescence quantum yields compared with [Ir(ppy)₃] and [Ir(df‐ppy)₃], the iridium(III) complexes containing triazolylpyridine ligands gave greater electrogenerated chemiluminescence (ECL) intensities (using tri‐n‐propylamine (TPA) as a co‐reactant), which can in part be ascribed to the more energetically favourable reactions of the oxidised complex (M⁺) with both TPA and its neutral radical oxidation product. The calculated iridium(III) complex LUMO energies were shown to be a good predictor of the corresponding M⁺ LUMO energies, and both HOMO and LUMO levels are related to ECL efficiency. The theoretical and experimental data together show that the best strategy for the design of efficient new blue‐shifted electrochemiluminophores is to aim to stabilise the HOMO, while only moderately stabilising the LUMO, thereby increasing the energy gap but ensuring favourable thermodynamics and kinetics for the ECL reaction. Of the iridium(III) complexes examined, [Ir(df‐ppy)₂(ptb)]⁺ was most attractive as a blue‐emitter for ECL detection, featuring a large hypsochromic shift (λ_max=454 and 484 nm), superior co‐reactant ECL intensity than the archetypal homoleptic green and blue emitters: [Ir(ppy)₃] and [Ir(df‐ppy)₃] (by over 16‐fold and threefold, respectively), and greater solubility in polar solvents.     

Enhanced Iridium Complex Electrochemiluminescence Cytosensing and Dynamic Evaluation of Cell‐Surface Carbohydrate Expression

A newly prepared [(ppy)₂Ir(dcbpy)]⁺?PF₆^? (ppy: 2‐phenylpyridyl; dcbpy: 4,4′‐dicarboxy‐2,2′‐bipyridyl) and gold nanoparticle functionalized mesoporous silica nanoparticle (Au/Ir‐MSN) is reported. Based on the binding between concanavalin A (Con A) and mannose, the novel nanoparticle was applied to an ultrasensitive electrochemiluminescence (ECL) in situ cytosensing strategy and the dynamic evaluation of cell‐surface carbohydrate expression. The ECL activity of the presented Con A@Au/Ir‐MSN nanoprobe was greatly enhanced by employing a functionalized nanoparticle and graphene nanomaterial with an increased surface area and simultaneously improved electron‐transfer efficiency at the electrode interface. Under optimal conditions, the sandwich‐type ECL cytosensor showed a linear response to K562 cells at concentrations ranging from 1.0×10² to 1.0×10⁶ cells mL^?1 and realized a low detection limit of a single cell. The proposed method could also be successfully used for monitoring the dynamic variation of carbohydrate expression in cancer cells in response to external stimulation by an inhibitor.     

Emission from the working and counter electrodes under co-reactant electrochemiluminescence conditions

We present a new approach to explore the potential-dependent multi-colour co-reactant electrochemiluminescence (ECL) from multiple luminophores. The potentials at both the working and counter electrodes, the current between these electrodes, and the emission over cyclic voltammetric scans were simultaneously measured for the ECL reaction of Ir(ppy)₃ and either [Ru(bpy)₃]²⁺ or [Ir(df-ppy)₂(ptb)]⁺, with tri-n-propylamine as the co-reactant. The counter electrode potential was monitored by adding a differential electrometer module to the potentiostat. Plotting the data against the applied working electrode potential and against time provided complementary depictions of their relationships. Photographs of the ECL at the surface of the two electrodes were taken to confirm the source of the emissions. This provided a new understanding of these multifaceted ECL systems, including the nature of the counter electrode potential and the possibility of eliciting ECL at this electrode, a mechanism-based rationalisation of the interactions of different metal-complex luminophores, and a previously unknown ECL pathway for the Ir(ppy)₃ complex at negative potentials that was observed even in the absence of the co-reactant.

Exploration of potential-dependent, multi-colour co-reactant electrochemiluminescence from multiple luminophores at the working and counter electrodes reveals new pathways to emission.     

Efficient electrochemiluminescent cyclometalated iridium(III) complexes: Synthesis,photophysical and electrochemiluminescent properties

A series of new cyclometalated iridium(III) complexes for electrochemiluminescence (ECL) system were synthesized and fully characterized. Using tri-n-propylamine (TPA) as an oxidative–reductive co-reactant, their ECL properties were studied in acetonitrile (CH₃CN) and mixed CH₃CN/H₂O (50:50, v/v) solutions, respectively. Meanwhile, the influencing factors of ECL efficiencies, including working electrode, pH, and surfactant were investigated. A remarkable ECL enhancement (up to about 13.5 times), in comparison with the commonly used Ru(bpy)₃²⁺ (2,2′-bipyridyl) ruthenium(II), is observed from Ir(FPP)₂(acac) (where FPP is 2-(4-fluorophenyl)-4-phenylpyridine, acac = acetylacetone) at Pt disk electrode. At the same time, an increase in ECL efficiency is also observed in surfactant media. This study provided a new method for further improving and tuning the ECL efficiency by designing new iridium complexes with the appropriate cyclometalated or ancillary ligands.