Systematic study of muon transfer to sulphur dioxide

In a systematic study of the transfer process to sulphur dioxide, in seven different H₂ + SO₂ gas mixtures, the time spectra of the muonic sulphur X-rays yield muon transfer rates to the SO₂ molecule, deduced from the lifetimes of the p atoms, which agree all well with each other. The muonic oxygen time spectra show an additional structure as if p atoms of another kind were present. Reduced transfer rates_O are reproducible if one uses the model of ephemeral p atoms. The intensity ratios between the different kinds of p atoms are also discussed in the framework of this model and the one of black and white p atoms.     

Laser damage in silicon photodiodes

Thermal damage of silicon photodiodes exposed to intense optical radiation is investigated. Damage thresholds of Si photodiodes irradiated by 1.06m laser pulses are reported for values of irradiation time,, ranging from 10^–8 to 1s. Threshold laser irradiation produces visible microscopic damage and a permanent degradation in photoresponse. The loss of responsivity is associated with degradation of the detector diode characteristics due to laser-induced heating. The time and wavelength dependence agree with the predictions of a thermal model which treats a semi-infinite material irradiated by a Gaussian laser beam. The energy density thresholds are independent of for short irradiation times and asymptotically approach a limiting behaviour which increases as for long times. They are given by the empirical relationE ₀=65[1+217/tan^–1(258)^1/2] J cm^–2 for 1.06m radiation. The thresholds at short irradiation times of detectors damaged by 1.06m radiation are about 25 times larger than those of detectors exposed to 0.6943m radiation. The greater susceptibility at 0.6943m is attributed to a larger optical absorption coefficient.     

Pulsed 532 nm laser wirestripping: Removal of dye-doped polyurethane insulation

Removal of rhodamine 6G doped polyurethane insulation coated onto 50 m diameter wire is shown to proceed efficiently and cleanly by irradiation with 532 nm Q-switched pulses from a Nd:YAG laser. The stripping action produced by this method is similar in quality to excimer laser wirestripping. Several experimental parameters were explored including fluence, pulse duration, dye concentration, and the number of incident pulses. Acceptable stripping conditions were obtained for a 3–5 s exposure at 10 Hz, using a dye concentration of 10% by weight, and 12 n pulses at 650 mJ/cm². Nearly 0.5 m/pulse is removed at this fluence, which exceeds the threshold fluence of 600 mJ/cm² by only 50 mJ/cm². The measured 532 nm absorption coefficient of the 10% dye-doped polyurethane was 4×10⁴ cm^–1. Lower fluences and/or dye concentrations produced inadequate stripping, while shorter duration pulses caused unacceptable melting of the thin gold layer which covered the copper core of the wire. Pulse-by-pulse photographs of the stripping action clearly show melting of the dye/polymer insulation, and thermal rollback of the insulation near the stripped end. Regardless, excellent edge definition is obtained by this method.     

μ+SR in magnetically ordered BCC metals: Local fields, μ+ sites,quantum diffusion,and strain effects

The paper gives a critical discussion of the procedures for extracting from the ⁺SR signals obtainable on magnetically ordered metals information on ⁺ sites, on local lattice distortions induced by the ⁺, on the local magnetic fields felt by the ⁺, and on quantum diffusion. Results for-Fe are: ⁺ occupy O sites, the tetragonality of the elastic double-force tensor isA–B 2eV, the dipolar magnetic field acting on the ⁺ isB _dip=(0.66±0.02)T. Using this information ⁺ hopping rates and diffusivities in Fe are deduced and compared with diffusivities obtained for hydrogen and deuterium. From this it is concluded that hydrogen in Fe diffuses via the adiabatic mechanism. In addition, the paper contains a brief summary of the theoretical background required for taking advantage of the rather large ¦A– B¦ values expected for ⁺ at O sites in bcc metals in order to gain information on the effects of energy asymmetries between neighbouring ⁺ sites on the ⁺ hopping rates.     

Sub-surface damage in indium phosphide caused by micromachining of grooves with femtosecond and nanosecond laser pulses

Grooves laser-micromachined in InP using 130 fs and 8 ns pulses with fluences 2 and 0.7 J/cm² are investigated by cross-sectional transmission electron microscopy. At the fluence of 2 J/cm², irradiation with both femtosecond and nanosecond laser pulses yield substantial resolidified layers with a maximum thickness of 0.5 m. In contrast, at the fluence of 0.7 J/cm², irradiation with nanosecond pulses leads to a layer of similar thickness, while femtosecond irradiation produces laser induced periodic surface structures with minimal resolidified material. For both fluences, femtosecond pulses generate substantial densities of defects extending over a few microns in depth, while nanosecond laser irradiation leads to no observable damage beneath the resolidified layer. The high peak power density and the stress confinement obtained from femtosecond pulses, along with incubation effects, are identified as the major factors leading the observed plastic deformations. PACS 61.80.Ba; 68.35.Gy; 79.20.Ds     

Tuning characteristics of a uv preionized 20-atmospheres CO2 laser

The tuning characteristics of a uv preionized 20-atmospheres gas discharge CO₂ laser with a novel and simple preionization scheme have been investigated. Continuous tunability in all branches of the 9.4 m and 10.4 m band with a total tuning range of more than 60 cm^–1 without frequency pulling is demonstrated. Additionally, a study of the laser pulse behaviour was performed.     

Transient pressure induced by laser ablation of toluene, a highly laser-absorbing liquid

Transient processes of laser ablation of a highly laser-absorbing liquid, toluene, were investigated by directly measuring (by using a fast-response pressure gauge) the transient pressure caused by toluene ablation under KrF laser irradiation . The results were compared with time-resolved images . The peak pressure P due to a shock wave decreased slowly with increasing distance d for d=100–1000 m:Pd^-0.33. By extrapolating P to d=8.9 m, the optical penetration depth of toluene at =248 nm, the estimated initial pressure due to toluene ablation was 65 MPa at 1.0 J cm^-2 pulse^-1. The estimated initial pressure increased linearly with the fluence. These results help clarify the mechanism of laser-induced backside wet etching. PACS 79.20.Ds; 47.40.Nm; 47.55.Bx; 81.65.Cf     

New cascade laser transitions in CH2F2 pumped with the 9R32 line of a cw CO2 laser

New cascade laser transitions of¹²CH₂F₂ at 172.50m, 208.83m, 220.44m, 223.99m and 250.61m are reported. A waveguide FIR laser was pumped with a quasi cw¹²C¹⁶O₂ laser operating on the 9R32 line. Together with the already known lines at 184.3m, 196.1m and 235.9m, the laser lines can be assigned to rotational transitions in the ₉ vibrational band of¹²CH₂F₂ and to refill transitions of the vibrational ground state ₀.     

Imaging and focusing of an atomic beam with a large period standing light wave

A novel atomic lens scheme is reported. A cylindrical lens potential was created by a large period ( 45 m) standing light wave perpendicular to a beam of metastable He atoms. The lens aperture (25 m) was centered in one antinode of the standing wave; the laser frequency was nearly resonant with the atomic transition 2³ S ₁–2³ P ₂ (=1.083 m) and the interaction time was significantly shorter than the spontaneous lifetime (100 ns) of the excited state. The thickness of the lens was given by the laser beam waist (40 m) in the direction of the atomic beam. Preliminary results are presented, where an atomic beam is focused down to a spot size of 4 m. Also, a microfabricated grating with a period of 8 m was imaged. We discuss the principle limitations of the spatial resolution of the lens given by spherical and chromatic aberrations as well as by diffraction. The fact that this lens is very thin offers new perspectives for deep focusing into the nm range.     

Efficient ablation of organic polymers polyether sulphone and polyether ether ketone by a TEA CO2 laser with high perforation ability

Organic polymer (PES: PolyEther Sulphone and PEEK: PolyEther Ether Ketone) ablation with oscillation-line selected TEA CO₂ lasers is successfully demonstrated. With different irradiation conditions the ablative etch-rate slopes were varied, which means that the ablation process is dependent on the ablation conditions such as incident laser intensity and ambient gas. In perforation processing of the PEEK film, the TEA CO₂ laser had a higher etch rate of 42 m/pulse at a fluence of 70 J/cm² in vacuum than the XeCl laser.     

Fabrication and low threshold current density CW operation of GaInAsP/InP multiple-reflector microcavity laser

We report CW operation of a GaInAsP/InP multiple-reflector microcavity (MRMC) laser operated at fairly low threshold current density. The threshold current density with broad contact (stripe widthW=240 m, cavity lengthL=60 m) under pulsed operation was 180 A cm^–2 (l _th=20 mA), and was 230 A cm^–2 under CW operation at room temperature operating at 1.52 m wavelength.     

Optical and Photoelectric Inhomogeneity of CdTe:V Crystals

The optical and photoelectric properties of CdTe:V crystals with the doping impurity concentration N _V = 5·10¹⁸–5·10¹⁹ cm^–3 are investigated and the possibility of their use as a photorefractive material is considered. As is seen from the spectra of optical transmission, the crystals of both types possess high transparency (50–65%), which for CdTe:V specimens with N _V = 5·10¹⁹ cm^–3 decreases sharply and in the range 12–14 m does not exceed 5%, whereas for CdTe:V crystals with vanadium concentration of 5·10¹⁸ cm^–3 such a value of transmission remains unchanged up to 25 m, implying a good optical quality of the latter crystals and their possible application in the spectral range 1.06–1.25 m in modern fiber-optic communication lines.     

Measurement of the refractive index and optical absorption spectra of epitaxial bismuth substituted yttrium iron garnet films at uv to near-ir wavelengths

Refractive-index and optical-absorption spectra of Bi-substituted yttrium iron garnet films, epitaxially grown by liquid-phase epitaxy, have been measured in the spectral regime 0.26 m1.9 m by thin-film interference for 0.52 m and by ellipsometry for0.52 m. The Y_3–x–y Bi _x Pb _y Fe_5–z Pt _z O₁₂ films contain bismuth in the range Ox 1.42, lead in the range 0.01 y0.08 and platinum in the range 0.005<=z0.03. There is satisfactory coincidence between the results from ellipsometry and thin-film interference in the overlapping wavelength region. The materials investigated are the same as reported earlier from this laboratory in ter mof their magnetic and magnetooptic properties.     

Adhered Supported Carbon Nanotubes

Carbon nanotubes (NTs) in excess of 200 m long are grown by catalytic pyrolysis of hydrocarbon vapors. The nanotubes grow continuously without the typical extinction due to catalyst encapsulation. A woven metal mesh supports the nanotubes creating a metal supported nanotube (MSNT) structure. The 140 m wide mesh openings are completely filled by 70 nm diameter multiwalled nanotubes (MWNTs). The MWNTs are straight, uniform and highly crystalline. Their wall thickness is about 10 nm (30 graphite layers). The adherent NTs are not removed from the support in a Scotch tape pull test. A 12.5 cm² capacitor made from two MSNT structures immersed in 1 M KCl has a capacitance of 0.35 F and an equivalent series resistance of 0.18 . Water flows through the MSNT at a flow velocity of 1 cm/min with a pressure drop of 15 inches of water. With the support removed, the MWNTs naturally form a carbon nanocomposite (CNC) paper with a specific area of 80 m²/gm, a bulk density of 0.21 g/cm³, an open pore fraction of 0.81, and a resistivity of 0.16 -cm.     

Excimer-laser-induced ablation of the high-T c superconductor Bi-Ca-Sr-Cu-O

The ablation of ceramic Bi-Ca-Sr-Cu-O by XeCl-excimer-laser projection has been investigated. In both air and vacuum, etching commences at about 2.4 J/cm² and then increases with fluence within the regime investigated ( <) 20 J/cm²). At 10 J/cm² the respective etch rates are around 1 m/pulse and 1.6 m/pulse.     

Sub-picosecond UV-laser ablation of Ni films

Laser ablation of thin Ni films on fused silica by 0.5 ps KrF-excimer-laser pulses at 248 nm is reported. The onset of material removal from different film thicknesses (0.1, 0.3, 0.6 and 1.0 m) was measured in a laser ionization time-of-flight mass spectrometer by the amount of Ni atoms vs laser fluence. Significant amounts of metal atoms are already evaporated at laser fluences around 20 mJ/cm², a threshold up to 100 times smaller compared to the one for 14 ns pulses. In contrast to ns laser pulses, the ablation threshold for 0.5 ps pulses is independent of the film thickness. These results reflect the importance of thermal diffusion in laser ablation of strongly absorbing and thermally good conducting materials and prove that for ablation with short pulses, energy loss to the bulk is minimized.     

Frequency of lamb-dip-stabilized 1.52 μm He-Ne lasers

A ³He-²⁰Ne and a ³He-²²Ne 1.52 m laser were frequency stabilized to the Lamb-dip of their respective gain curve and provided a resettability of 2 MHz. Using these lasers, absolute frequencies for the ²⁰Ne and ²²Ne laser transitions were measured by interferometric frequency comparison with an I₂-stabilized He-Ne laser at 0.633 m. A least-square analysis which accounts for the linear frequency dependence of the laser gas pressure yielded two parameters which can reproduce the measured frequencies within an accuracy of ±1.0·10^–8 at 1.52 m.     

Iodine photodissociation laser system Perun II

A construction and exploitation of a medium size iodine photodissociation laser system Perun II is reported. This laser produced pulses of infrared light (=1.315m) up to 50 J in energy and 300 ps in duration. The diameter of the beam is 82 mm. The beam divergence is about 4×10^–4 rad. The laser beam can be focused in a focal spot of a power density exceeding 10¹⁴ W/cm². The resuls of measurements of basic plasma parameters on an Al foil target are also presented. A recent improvement of the system includes a conversion to the second harmonic by a DKDP crystal.Presented at bilateral international seminar of High Temperature Laser Plasma and High Gain Iodine Lasers held on 4 July 1991 in the Inst. of Physics, Czechosl. Acad. Sci., in Prague (organized by Division of Optics of the Inst. of Physics, Czechosl. Acad. Sci., and Physical Section (Plasma Division) of the Union of Czech Mathematicians and Physicists.     

Actively mode-locked 1.3 and 1.55 μm InGaAsP diode lasers

Active mode-locking of uncoated InGaAsP diode lasers having an external diffraction grating cavity was investigated experimentally. A high frequency r.f. signal and short-duration electrical pulses were used to drive the lasers. The pulse duration was measured by an ultrafast streak camera. Pulses as short as 13 ps at 1.3m and 29 ps at 1.55m were generated at a repetition rate of 1 GHz. The reason for obtaining broader pulses from the 1.55m laser which had the same structure as the 1.3m diode laser is explained.Formerly with GEC Hirst Research Centre, Wembley, Middlesex, UK.     

Femtosecond-pulse laser ablation of human corneas

A femtosecond pulse laser in the visible spectral region shows promise as a potentially new powerful corneal sculpting tool. It combines the clinical and technical advantages of visible wavelengths with the high ablation quality observed with nanosecond-pulse excimer lasers at 193 nm. A femtosecond and a nanosecond dye laser with pulse durations of 300 fs and 7 ns, and centre wavelengths at 615 nm and 600 nm, respectively, both focused to an area of the order of 10^–5 cm², have been applied to human corneal ablation. Nanosecond laser pulses caused substantial tissue disruption within a 30–100 m range from the excision edge at all fluences above the ablation threshold of F _th60 J cm^–2 (I _th9 GW cm^–2). Completely different excisions are produced by the femtosecond-pulse laser: high quality ablations of the Bowman membrane and the stroma tissue characterised by damage zones of less than 0.5 m were observed at all fluences above ablation threshold of F _th1 J cm^–2 or I _th3 TW cm^–2 (3×10¹² W cm^–2). The transparent cornea material can be forced to absorb ultrashort pulses of extremely high intensity. The fs laser generates its own absorption by a multiphoton absorption process.