Capillary electrochromatographic separation of proteins on a column coated with titanium dioxide nanoparticles

A TiO2 nanoparticle (TiO2 NP)-coated open-tubular column for the capillary electrochromatographic separation of proteins is described. The surface chemistry of the TiO2 NPs on the inner wall of the fused silica was significantly affected by the running buffer. By varying of the phosphate buffer pH, only cathodic EOF was indicated. The results showed that TiO2 NPs are existed as a complexed form with the buffer ligand. Good separation of conalbumin (ConA), apo-transferrin (apoTf), ovalbumin (OVA), and BSA could be achieved with phosphate buffer (40 mM, pH 8.0) and an applied voltage of 15 kV. Five peaks of glycoisoforms of OVA were observed under these conditions. In comparison with the retention behavior of the analytes on the bare fused-silica column, the new column's high resolving power seems to be predominantly derived from the ligand exchange of the analytes with the phosphate adsorbed onto the TiO2 NPs. The method was also used to separate egg-white proteins. Both acidic and basic proteins in egg white were separated in a single run. The microheterogeneities of OVA could also be found in it. The separation efficiency for the main peak of OVA in egg white was around 10,000 plates/m.     

Capillary electrophoresis of double-stranded DNA in an untreated capillary.

Using the zwitterionic buffer N-2-hydroxyethylpiperazine-N'-2-ethanesulfonic acid (HEPES) in the presence of a high-molecular-mass hydroxypropylmethylcellulose (HPMC) as a sieving polymer and ethidium bromide double-stranded DNA (dsDNA) was separated in an untreated capillary. The HEPES buffer shielded the DNA against the capillary wall interaction and decreased the electroosmotic flow enabling a good separation of the DNA similar to that obtained in a commercially coated capillary. In addition to the low cost of the untreated capillary it can be washed after each run. Furthermore, stacking with hydrodynamic injection filling about half of the capillary volume is demonstrated.     

硫醇-烯点击化学法制备C18毛细管电色谱开管柱及其性能研究

基于十八烷基硫醇与乙烯基功能化毛细管(Vinyl capillary)的硫醇-烯点击化学反应,制备了一种新型的C18毛细管电色谱开管柱(C18capillary).采用乙烯基三甲氧基硅烷对毛细管内壁进行乙烯基功能化,然后通过硫醇-烯点击化学反应共价键合十八烷基硫醇于Vinyl capillary内表面.采用环境扫描电镜对C18 capillary进行了形貌表征.考察了缓冲溶液pH值对C18 capillary、Vinyl capillary和裸毛细管柱(Bare capillary)电渗流的影响.结果表明;在相同实验条件下,C18capillary的电渗流最小.以3种多环芳烃为模型化合物,评价了C18capillary的电色谱柱性能;同时考察了模型化合物在C18capillary上的电色谱保留行为.实验表明,其保留机理是基于典型的反相作用.当C18 capillary用于碱性模型化合物分离时,碱性物质在C18 capillary上的峰形较好,无明显的峰拖尾现象,这可能是由于C18capillary表面含有极性的S基团能够屏蔽残留硅羟基对碱性化合物的吸附作用.     

Phospholipid-lysozyme coating for chiral separation in capillary electrophoresis

A phospholipid coating with lysozyme as chiral recognition reagent permeated into the phospholipid membrane was developed for the chiral capillary electrophoretic (CE) separation of D- and L-tryptophan. As a kind of carriers, coated as phospholipid membranes onto the inner wall of a fused-silica capillary, liposomes are able to interact with basic proteins such as lysozyme, which may reside on the surface of the phospholipid membrane or permeate into the middle of the membrane. The interaction results in strong immobilization of lysozyme in the capillary. Coatings prepared with liposomes alone did not allow stable immobilization of lysozyme into the phospholipid membranes, as seen from the poor repeatability of the chiral separation. When 1-(4-iodobutyl)-1,4-dimethylpiperazin-1-ium iodide (M1C4) was applied as a first coating layer in the capillary, the electroosmotic flow (EOF) was effectively suppressed, the phospholipid coating was stabilized, and the lysozyme immobilization was much improved. The liposome composition, the running buffer, and the capillary inner diameter all affected the chiral separation of D- and L-tryptophan. Coating with 4 mM M1C4 and then 1 mM phosphatidylcholine (PC)/phosphatidylserine (PS) (80:20 mol%), with 20 mM (ionic strength) Tris at pH 7.4 as the running buffer, resulted in optimal chiral separation with good separation efficiency and resolution. Since lysozyme was strongly permeated into the membrane of the phospholipids on the capillary surface, the chiral separation of D- and L-tryptophan was achieved without lysozyme in the running buffer. The effects of different coating procedures and separation conditions on separation were evaluated, and the M1C4-liposome and liposome-lysozyme interactions were elucidated. The usefulness of protein immobilized into phospholipid membranes as a chiral selector in CE is demonstrated for the first time.     

Graft copolymer composed of cationic backbone and bottle brush-like side chains as a physically adsorbed coating for protein separation by capillary electrophoresis

To stabilize electroosmotic flow (EOF) and suppress protein adsorption onto the silica capillary inner wall, a cationic hydroxyethylcellulose-graft-poly (poly(ethylene glycol) methyl ether methacrylate) (cat-HEC-g-PPEGMA) graft copolymer composed of cationic backbone and bottle brush-like side chains was synthesized for the first time and used as a novel physically adsorbed coating for protein separation by capillary electrophoresis. Reversed (anodal) and very stable EOF was obtained in cat-HEC-g-PPEGMA-coated capillary at pH 2.2-7.8. The effects of degree of cationization, PEGMA grafting ratio, PEGMA molecular mass, and buffer pH on the separation of basic proteins were investigated. A systematic comparative study of protein separation in bare and HEC-coated capillaries and in cat-HEC-g-PPEGMA-coated capillary was also performed. The basic proteins can be well separated in cat-HEC-g-PPEGMA-coated capillary over the pH range of 2.8-6.8 with good repeatability and high separation efficiency, because the coating combines good protein-resistant property of bottle brush-like PPEGMA side chains with excellent coating ability of cat-HEC backbone. Besides its success in separation of basic proteins, the cat-HEC-g-PPEGMA coating was also superior in the fast separation of other protein samples, such as protein mixture, egg white, and saliva, which indicates that it is a promising coating for further proteomics analysis.     

A mesoporous silica nanoparticles immobilized open-tubular capillary column with a coating of cellulose tris(3,5-dimethylphenyl-carbamate) for enantioseparation in CEC

An approach of immobilizing mobile crystalline material (MCM)-41 mesoporous silica nanoparticles on the inner wall of an open-tubular (OT) capillary as the support for coating chiral selector of cellulose tris(3,5-dimethylphenyl-carbamate) (CDMPC) was carried out. By taking advantage of the improved phase ratio of OT capillary with the immobilization of MCM-41 mesoporous material, the cellulose derivative of CDMPC as the chiral selector was simply coated on the MCM-41 nanoparticle layer via the hydrogen-bonding interaction, and the enantioseparation was successively carried out. Eight pairs of acidic, neutral and basic enantiomers were resolved in capillary electrochromatography or capillary liquid chromatography mode. The concentration of CDMPC for coating was systematically investigated to obtain the optimized chromatographic properties on enantioseparation by controlling the supposed film thickness of CDMPC on MCM-41 nanoparticle layer. Comparing with a bare fused silica capillary column coated with CDMPC under the same coating procedure as MCM-41-modified capillary did, the MCM-41-modified capillary column offered much higher enantioselectivity. This result indicated the significance of using the mesoporous nanoparticles as the electrochromatographic support to enhance the phase ratio of OT capillary column in capillary electrochromatography and capillary liquid chromatography. For investigating the effect of experimental conditions on the enantioseparation with this prepared OT capillary column, the content of organic modifier acetonitrile in the mobile phase was thus extensively evaluated to achieve a better chiral separation.     

Capillary electrophoresis of proteins in dextran-coated columns

A simple coating technique by using uncross-linked dextran has been developed for fused-silica capillaries to be used in capillary electrophoresis of basic proteins. The capillaries were first silanized with a heterobifunctional silane (gamma-aminopropyltriethoxylsilane), which served as a coupling agent between the capillary inner wall and the polysaccharide coating. Dextran of high molecular mass (about 70 kDa) was activated with 1,1'-carbonyldiimidazole. Then the activated dextran was coupled to the primary amino groups that were anchored onto the inner wall of the silanized capillaries. The residual reactive groups on the dextran were further substituted by neutral functions in a coupling reaction with excess ethanolamine. By using dimethyl sulfoxide (DMSO) rather than aqueous buffer as the reaction medium, the extent of substitution was improved by minimizing the residual reactive groups at the surface. Since they are ionogenic, the electrosmotic flow in the system is relatively low. The chemically bound dextran coating showed good reproducibility and stability. In electrophoretic experiments basic proteins were separated with high efficiency by use of the dextran-coated fused-silica capillary columns. The main advantage of the method described here is that both polysaccharide activation and amine-coupling reactions were carried out under mild conditions at room temperature without catalysts. For this reason, the method is recommended to coat the inner wall of microfluidic separation channels which would not tolerate a harsh treatment.     

Open-tubular capillary electrochromatography of bovine beta-lactoglobulin variants A and B using an aptamer stationary phase.

DNA aptamers that form a G-quartet conformation were covalently attached to a capillary surface for open-tubular capillary electrochromatographic separation of bovine beta-lactoglobulin variants A and B, which vary by 2 of their 162 amino acid residues. Separation was achieved using a 4-plane, G-quartet aptamer stationary phase with tris(hydroxymethyl)aminomethane (Tris) or phosphate buffer as the mobile phase. In control experiments, separation did not occur using either an oligonucleotide of similar base composition but which does not form a G-quartet structure, or using capillary zone electrophoresis on a bare capillary under similar experimental conditions. Separation was achieved using a capillary coated only with the covalent linker molecule. In phosphate buffer, the separations were similar for aptamer-coated and linker-only stationary phases, while in Tris buffer, retention times were almost doubled for the linker-only capillary. When Tris buffer is the mobile phase, there appears to be weaker interactions between the proteins and the stationary phase that may result in a gentler, less denaturing separation than is commonly achieved using hydrocarbon-based stationary phases.     

The application of functional silica nanoparticles to fulfill the rapid and improved enantioselective capillary electrophoresis separation of amino acid derivatives

In this study, diamino moiety functionalized silica nanoparticles with the size of 118 ± 12 nm were successfully synthesized and directly introduced into a chiral capillary electrophoresis system to improve the enantioseparation of 9‐fluorenyl methoxycarbonyl derivatized amino acids using norvancomycin as chiral selector. Under acidic background electrolyte conditions, functional silica nanoparticles can be readily adsorbed onto the inner surface of bare silica capillary column through electrostatic interaction to form a dynamic coating, resulting in a reversed anodic electro‐osmotic flow (i.e. from cathode to anode). As expected, chiral amino acid derivatives (usually negatively charged) can be rapidly separated under co‐electro‐osmotic flow conditions in the current separation system. Furthermore, the column performance and detection sensitivity for the enantioseparation were also obviously improved because the adsorption of chiral selector of norvancomycin to the capillary wall was greatly suppressed. Some important factors influencing the separation, such as the coating thickness, background electrolyte concentration, functional silica nanoparticles concentration, and the organic modifier were also investigated and the optimized separation conditions were obtained.     

Open-tubular capillary electrochromatography/electrospray ionization-mass spectrometry using polymeric surfactant as a stationary phase coating

We describe the use of the polymeric surfactant poly(sodium undecylenic sulfate) (poly-SUS) as a stationary phase coating in open-tubular capillary electrochromatography (OT-CEC) coupled with electrospray ionization-mass spectrometry (ESI-MS) for the analysis of beta-blocker and benzodiazepine analytes. The production of a polymeric surfactant coating on the capillary inner wall involves (i) adsorption of the cationic polymer poly(diallyldimethylammonium chloride) (PDADMAC) to the inner surface of capillary, and (ii) adsorption of the negatively charged poly-SUS onto the cationic polymer layer via strong physical interaction of the two polymer layers. As compared with micellar electrokinetic chromatography (MEKC) coupled with ESI-MS, the main advantage of this proposed method is minimization of introduction of the monomeric or polymeric surfactant into the mass spectrometer, thus avoiding the interference of the nonvolatile micelle in ESI-MS. The effects of buffer pH and applied voltage on the separation of the analytes are also discussed. Under optimum conditions, four of the five beta-blockers and four benzodiazepines are separated.     

动力学涂层毛细管电泳分离双链脱氧核糖核酸片段

以异丙醇为聚合反应链转移试剂，水相法合成了短链聚N，N－二甲基丙烯酰胺（PDMA），研究表明，该聚合物能在毛细管内壁形成稳定的动力学涂层，从而有效地抑制电渗流和毛细管内壁与DNA的作用。这种介质被成功地应用于DNA片段的高效分离。     

Rapid separation of barbiturates and benzodiazepines by capillary electrochromatography with 3-(1,8-naphthalimido)propyl-modified silyl silica gel

A capillary electrochromatographic (CEC) method was applied to the simultaneous separation of barbiturates (barbital, phenobarbital, secobarbital and thiopental) and benzodiazepines (nitrazepam, diazepam and triazolam). The separation was performed in a 75 microm i.d. capillary, packed with 3-(1,8-naphthalimido)propyl-modified silyl silica gel (NAIP), studying the effects of buffer pH and mobile phase composition. Using an applied voltage of 20 kV and the short-end injection method (9 cm capillary effective length), the mobile phase of 1.0 mM citrate buffer (pH 5.0) containing 45% methanol provided the baseline separation of seven toxic drugs in less than 9 min. In CEC with NAIP, the benzodiazepines were separated by the combination of hydrophobic and pi-pi interactions, whereas the separation of the barbiturates was based on the hydrophobic interaction.     

Separation of atropisomers of anti-hepatitis drug dimethyl diphenyl bicarboxylate analogues by capillary electrophoresis with vancomycin as the chiral selector

Separation of atropisomers of analogues of the anti-hepatitis drug dimethyl diphenyl bicarboxylate (DDB) by capillary electrophoresis with vancomycin as the chiral selector is described. Among several tested chiral selectors, including various cyclodextrin derivatives as well as vancomycin, only the latter displayed the enantioselectivity to the studied atropisomers. However, relatively poor separation efficiency was obtained due to the adsorption of vancomycin on the capillary wall. This problem was overcome by modifying the capillary wall with a polycationic electrolyte named hexadimethrine bromide (HDB) to produce a positively charged coating, which minimized the adsorption of vancomycin on the capillary wall by electrostatic repulsion. Moreover, the positively charged coating could shorten the separation time by reversing the EOF because the reversed EOF migrated to the same direction as the negatively charged analyte. Effects of buffer pH, vancomycin and buffer concentrations and applied voltage on the separation were investigated and the optimal conditions were established as follows: 40 mM Tris-phosphate buffer (pH 6.0) containing 6.0 mM vancomycin and 0.001% HDB. Baseline separation of three racemic DDB analogues was obtained within 12 min under the optimal conditions.     

Enhanced stability of surfactant-based semipermanent wall coatings in capillary electrophoresis using oppositely charged surfactant

Semipermanent surfactant coatings are effective for the prevention of wall adsorption of proteins in CE. However, they often suffer from their unsatisfactory coating stability as they essentially degrade from the capillary walls after the surfactants are removed from the buffer. In this paper, we proposed a facile and universal method to improve the stability of semipermanent surfactant coatings based on addition of an oppositely charged surfactant into the coating. Didodecyldimethylammonium bromide (DDAB) and a gemini surfactant, 18-6-18, were used as the model semipermanent coatings, and sodium dodecyl sulfate (SDS) was chosen as their oppositely charged surfactant. SDS can strongly alter the packing parameter P of the cationic surfactants, and consequently mediates the coating stability. With the increase of SDS concentration in coating, the coating stability first dramatically increases due to the enlarged P, and then decreases due to the weakness of electrostatic interaction between the capillary wall and surfactant coating. At the proper SDS concentration, very stable coatings can be obtained that, even after rinsing under 138 kPa for 60 min, the reversed electroosmotic flow (EOF) only decreases by 3.6%. These SDS-enhanced coatings show excellent stability and reproducibility in protein separation (RSD of migration time <1.1% for run-to-run assay, n=9). Also, the high separation efficiency (>500,000 plates/m) and fine recovery of tested proteins indicate that these coatings are powerful in wall adsorption suppression. Finally, we found that the separation efficiency of protein was a more exact indicator for the coating stability than the traditional EOF magnitude.     

Sol‐gel technique for the preparation of β‐cyclodextrin gold nanoparticles as chiral stationary phase in open‐tubular capillary electrochromatography

A novel open‐tubular capillary electrochromatography column coated with β‐cyclodextrin was prepared using the sol‐gel technique. In the sol‐gel approach, owing to the three‐dimensional network of sol‐gel and the strong chemical bond between the stationary phase and the surface of capillary columns, good chromatographic characteristics and unique selectivity in separating enantiomers were shown. The influences of capillary inner diameter, coating time, organic modifier, buffer pH, and buffer concentration on separation were investigated. The sol‐gel‐coated β‐cyclodextrin column has shown improved enantioseparation efficiency of chlorphenamine, brompheniramine, pheniramine, zopiclone in comparison with the sol‐gel matrix capillary column. The migration time relative standard deviation of the separation of the enantiomers was less than 0.89% over five runs and 2.9% from column to column. This work confirmed that gold nanoparticles are promising electrochromatographic support to enhance the phase ratio of open‐tubular capillary electrochromatography column in capillary electrochromatography.     

Capillary electrochromatographic analysis of aliphatic mono- and polycarboxylic acids

The parameters influencing the electrochromatographic separation of aliphatic organic acids in a capillary column with a wall-coated macrocyclic polyamine have been studied. Indirect detection using chromate, pyromellitate, trimellitate, o-phthalate, benzoate and acetate as background electrolytes has been tested. A complete separation of polyprotic acids could be achieved with pyromellitate buffer (7.5 mM, pH 6.5), and satisfactory results for the simultaneous separation of monoprotic acids and polyprotic acids were found using a capillary column of 70 cm (50 cm effective length)x75 microm inner diameter, electrokinetic injection (-10 kV, 10 s), benzoate buffer (6 mM, pH 4.6), separation voltage of -10 kV, and detection at 220 nm. For the separation of the geometric isomers fumarate and maleate, acetate buffer was found the best choice among the background electrolytes tested. The method so established has been applied to the determination of organic acids in soy sauce, brandy, lemon juice, spinach juice and cigarette. From the retention behavior, it was found that the separation mechanism on the bonded phase was influenced by the macrocyclic effect, electrostatic attraction, hydrogen bonding, van der Waals forces, and anion exchange, in addition to the differences in electrophoretic mobility.     

A new type of capillary column for open-tubular electrochromatography

A new type of open-tubular C(18) ester-bonded electrochromatographic column was prepared with sol-gel technology, followed by an on-column octadecyl silylation reaction. Glycidoxypropyltrimethoxysilane, a widely used and important silane agent, was used as the sol-gel precursor to form a thin coating layer on the wall of the fused-silica capillary. The C(18) groups were introduced into the coating layer by on-column esterification reaction with stearic acid. The electrochromatography behavior of the column was evaluated in terms of the separation of peptides. A high efficiency of 4.8x10(5) plates/m was achieved for a basic pentapeptide using the C(18 )ester-bonded column. In comparison with bare capillaries and glycidoxypropyltrimethoxysilane sol-gel-coated capillaries, the C(18) ester-bonded column showed the best separation of a mixture of seven pentapeptides under identical conditions of buffer, pH, and applied voltage.     

pH effect on dynamic coating for capillary electrophoresis of DNA

A buffer consisting of tris(hydroxymethyl)aminomethane, 2-(N-moropholino)ethanesulfonic acid (Mes) and EDTA with constant ion strength was used to investigate the effect of buffer pH on the dynamic coating behavior of poly(N-isopropylacrylamide) (PNIPAM) for DNA separation. The atomic force microscopy (AFM) image illustrated that PNIPAM in lower-pH buffer was much more efficient in covering a silica wafer than that in higher-pH buffer. The coating performance of PNIPAM was also quantitatively analyzed by Fourier transform IR attenuated total reflectance spectroscopy and by measuring the electroosmotic flow (EOF). These results indicated that the stability of the dynamic coating was dependent on the pH of the sieving matrix and was improved by reducing the pH to the weak-acid range. The lower pH of the sieving buffer may induce the polymer more efficiently to adsorb on the capillary wall to suppress EOF and DNA–capillary wall interaction for DNA separation. The enhanced dynamic coating capacity of PNIPAM in lower-pH buffer may be attributed to the hydrogen bonds between the hydroxyl groups of the silica surface and the oxygen atom of the carbonyl groups of PNIPAM.     

Convenient enantioseparation by monolithic imprinted capillary clamped in a chip with electrochemical detection

A microchip integrated with a monolithic imprinted capillary has been manufactured for performing the chip-based capillary electrochromatographic enantioseparation. The microporous monolith anchored on the inner wall of the microchannel was prepared by in situ chemical copolymerization, and characterized with scanning electron microscopy, IR spectroscopy, and solid-state UV-vis spectroscopy. The monolithic network with high porosity gave a large surface area, good permeability, low mass-transfer resistance, and thus high separation efficiency. A portable microchip was conveniently constructed by integrating an imprinted capillary with 5-cm length as the separation channel and a carbon fiber microdisk working electrode for amperometric detection. Using L-tyrosine (L-Tyr) as the template molecule, Tyr enantiomers could be baseline separated within 55 s under the optimized preparation and separation conditions. The linear ranges for online amperometric detection of both Tyr enantiomers were from 20 to 2400 μM. The microporous monolithic chip strategy exhibited excellent separation efficiency and promising analytical application in enantioseparation. It opens an avenue for high-throughput screening of chiral compounds.     

Proline-coated column for the capillary electrochromatographic separation of amino acids by in-column derivatization

With 3-trimethoxysilylpropyl chloride as the spacer, a proline-coated capillary column was prepared for the capillary electrochromatographic (CEC) separation of amino acids by in-column derivatization. Nine standard mixtures, including aspartic acid, glutamic acid, valine, phenylalanine, alanine, isoleucine, leucine, tyrosine, and tryptophan, were injected. o-Phthalaldehyde (OPA), OPA/2-mercaptoethanol (2-ME) and OPA/N-acetylcysteine (NAC) in borate buffer were tested as the derivatizing agent. Among them, OPA (50 mM) in borate buffer (pH 9.5, 50 mM) gave the best performance. The formation of isoindole could be detected by UV detection. The sandwich-type injection was carried out in hydrostatic mode (10 cm) with the program R(10 s)S(10 s) R(10 s)W(10 min) with R, S, and W being the reagent, sample, and waiting times. Mesityl oxide, benzyl alcohol, and acetone showed some interaction with the column. A current monitoring method was used instead of the determination of the electroosmotic flow (EOF). The direction of EOF was from anode to cathode even under acidic condition lower than the pI value (6.31) of the bonded group due to some unreacted silanol groups. Some parameters including pH, nature, and concentration of the mobile phase and the effect of organic modifier with regard to the CEC separation were investigated. With the proline-coated column (75 (50) cm x 75 microm ID) the best separation was performed in phosphate buffer (pH 4.00, 100 mM) with an applied voltage of -15 kV. The established method was also compared with those precolumn derivatized prior to the separation with proline-coated column as well as with in-capillary derivatization and separation with a bare fused-silica column.