Polymer blend membranes of sulfonated poly(arylene ether ketone) for direct methanol fuel cell

The blend membranes of sulfonated poly(arylene ether ketone) (sPAEK) (IEC = 1.0 mequiv./g)/Nafion^® and the blend membranes of sPAEK (IEC = 1.0 mequiv./g)/sPAEK (IEC = 1.7 mequiv./g) were prepared. sPAEK with low IEC was introduced to reduce the methanol permeability through the membrane. Morphology, water uptake, proton conductivity and methanol permeability of the blend membranes were investigated by SEM, AFM, AC impedance spectroscopy and permeability measuring instrument. The cross-sections of blend membranes showed phase-separated morphologies. The effect of phase-separated morphology on the properties of blend membranes was investigated. The properties like water uptake, proton conductivity, and methanol permeability of sPAEK/Nafion^® blend membranes showed similar values with sPAEK and properties of sPAEK/sPAEK blend membranes showed intermediate values of two polymers due to the difference in morphology of the blend membranes. sPAEK/sPAEK blend membranes showed relatively high proton conductivity and lowered methanol permeability compared to Nafion^®. sPAEK/sPAEK blend membranes could be a competent substitution for Nafion^®.     

磺化聚芳醚砜/磺化聚酰亚胺复合质子交换膜的制备与性能研究

利用溶液浇铸法制备了一系列双磺化型磺化聚芳醚砜/磺化聚酰亚胺(SPAES/SPI)复合质子交换膜.扫描电子显微镜(SEM)结果显示复合膜不存在明显的相分离,表明二者具有很好的相容性.由于SPI的引入,复合膜在甲醇中稳定性较纯SPAES具有大幅的提高,比Nafion112低得多的甲醇吸收率表明了这些复合膜具有比后者更低的甲醇透过率.复合膜显示了与单组分膜相类似的高温分解稳定性,磺酸基团的分解温度达到了290℃以上.复合膜显示出远高于纯SPAES膜的尺寸稳定性能,在130℃高温中200h处理后,所有的复合膜均保持了高的机械性能,而此时纯SPAES膜已经溶解于水中.而且由于两种磺化聚合物间的复合,复合膜维持了较高的IEC水平,显示了较高的质子导电率,在80%相对湿度时的质子导电率与Nafion112相近,而在水中的质子导电率均高于Nafion112.     

Characteristics of polyethersulfone/sulfonated polyimide blend membrane for proton exchange membrane fuel cell

Solution-cast membranes from sulfonated polyimide (SPI) and its blend were prepared from polyethersulfone (PES) and SPI. The water uptake and swelling were tested and compared between the SPI membrane and the four kinds of blend membranes. Through comparison of the stability of the membranes, we concluded that the PES could greatly increase the stability of the whole membrane and restrict the swelling. However, the PES did not decrease the water uptake very much. We also compared the fuel cell performance with different membranes. The performance was decreased when the content of the PES in the blend membrane increased. The loss of the fuel cell performance with the blend membranes did not decrease very much before the content of the PES was exceeded 20%. It was prospected that the blend membrane could increase the stability of the SPI and, more importantly, even replace the commercial Nafion membranes.     

Studies on cellulose acetate-carboxylated polysulfone blend ultrafiltration membranes--Part I

Hydrophilic polysulfone ultrafiltration (UF) membranes were prepared from blends of cellulose acetate with carboxylated polysulfone of 0.14 degree of carboxylation. The effects of blend polymer composition on compaction, pure water flux, water content and membrane hydraulic resistance (R_m), have been investigated to evaluate the performance of the membranes. The performance of the blend membranes of various blend polymer compositions were compared with that of membranes prepared from pure cellulose acetate and blends of cellulose acetate and pure polysulfone. The hydrophilic cellulose acetate-carboxylated polysulfone blend UF membranes showed better performance compared to membranes prepared from pure cellulose acetate and blends of cellulose acetate and pure polysulfone.     

Polyaniline-poly(vinylidene fluoride) blend microfiltration membrane and its spontaneous gold recovery application

Structural regular polyaniline was synthesized via a modified-chemical oxidative polymerization reaction. Highly hydrophilic polyaniline (PANi) and polyaniline-poly(vinylidene fluoride) blend (PANi-PVDF) membranes were prepared by solution casting and phase inversion techniques. Both of the mechanical and filtration properties of the membranes depend on the polymer composition and doping level of the blends. The elasticity of the membrane is greatly improved upon introducing poly(vinylidene fluoride) into the blend. The water permeability of the blend membranes is further enhanced when the membranes are doped with hydrochloric acid. The PANi-PVDF blend membranes are capable of recovering metallic gold from the acid/halide leaching streams spontaneous and sustainably, and are promising candidates for wastewater treatments in electronic industries.     

Poly (caprolactone)/poly (ethylene glycol) pervaporation blend membranes: Synthesis,characterization, and performance

Poly (caprolactone) membranes with addition of different poly (ethylene glycol) concentrations were prepared for separation of water/isopropanol azeotropic mixture by pervaporation process. Different characterization tests including Fourier transform infrared, scanning electron microscopy, water contact angle, and thermogravimetric analysis were carried out on the prepared membranes. In addition, the effect of poly (ethylene glycol) PEG content on the swelling degree and the performance of the prepared membranes in pervaporation process were investigated. According to the obtained results, all the membranes were water selective and the blend membrane containing 3 wt% PEG exhibited the best pervaporation performance with a water flux of 0.517 kg/m² hour and separation factor of 1642 at the ambient temperature. Hydrophilicity improvement of the blend membranes was confirmed by constant decrease in water contact angle of the membranes as PEG content increased in the casting solution. Scanning electron microscopy cross‐sectional images indicated that the blend membranes containing PEG had a closed cellular structure. Furthermore, mechanical and thermal properties of the membranes decreased by adding PEG.     

Improved Mechanical Properties of Poly(butylene succinate) Membrane by Co-electrospinning with Gelatin

Gelatin, a natural proteinous polymer, was used to co-electrospin with poly(butylene succinate) (PBS) in order to improve the mechanical properties of PBS membrane and facilitate its applications in biomedical field. The PBS/gelatin blend membranes have narrower distribution of fiber diameter and smoother surface than neat PBS membrane. The contact angles, water absorption rates and water uptakes of the PBS/gelatin blend membranes were measured, showing increased hydrophilicity. The interaction between PBS and gelatin was investigated by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and differential scanning calorimetry (DSC). The mechanical properties of PBS/gelatin blend membranes in both dry and wet states were evaluated by uniaxial tensile tests. In the dry state, the PBS/gelatin blend membrane containing 10% gelatin has a 3-times increase in tensile strength without any adverse effect on ductility because of the existence of interaction between the two blend components, little change in crystallinity of PBS, and possible interaction between any adjacent fibers; the tensile strength and elongation at break are even better in the wet state attributed to some gelatin on fiber surfaces, which act as a binder in the presence of water. The potential applications of PBS/gelatin blend membranes were demonstrated by successful immobilization of thrombin, a clinically-used hemostatic drug. The thrombin-loaded membrane could be used for rapid hemostasis.     

木质素磺酸钠改性聚砜膜的制备及其在正渗透膜中的应用

采用木质素磺酸钠作为亲水添加剂,通过浸没沉淀相转化法制备了木质素磺酸钠共混改性聚砜膜,以改善聚砜膜的亲水性,并用作正渗透膜的支撑层,以降低内浓差极化效应.利用扫描电子显微镜、衰减全反射傅里叶变换红外光谱仪、水接触角仪等研究了不同木质素磺酸钠添加量对聚砜膜的结构和表面性质的影响.结果表明,添加木质素磺酸钠后,聚砜膜的指状孔变得规整且狭长.水接触角实验证实添加木质素磺酸钠能改善聚砜膜的亲水性,当木质素磺酸钠含量为0.4 wt%时,聚砜膜的表面水接触角可降低至65°.正/反渗透测试装置分别用于表征正渗透膜的传质性质和结构参数.结果表明,以0.4 wt%木质素磺酸钠改性聚砜膜为支撑层的正渗透膜的水渗透性能(A=3.12×10~(-5) LMH×Pa~(-1))优于纯聚砜基底正渗透膜(0.76×10~(-5)LMH×Pa~(-1)),而且前者的结构参数(S=2010mm)远小于后者(3450mm),说明木质素磺酸钠改性聚砜膜有效弱化了正渗透膜的内浓差极化效应.     

Blend membranes from cellulose/konjac glucomannan cuprammonium solution

The blend membranes were prepared from cellulose/konjac glucomannan (KGM) cuprammonium solution by coagulating with aqueous 10 wt% NaOH solution, 20°C and 40°C water, respectively. Miscibility, pore morphology, structure, water permeability and mechanical properties of the blend membranes were investigated. The complex forms of cellulose/KGM in the mixed solutions, the effect of various coagulants and the percent content of KGM (w_KGM) on the structure and properties of the blend membrane are discussed. SEM and mechanical relaxation analysis indicate that the blend membranes are miscible in the range of 0–30 wt% of w_KGM. When w_KGM was smaller than 20 wt%, the tensil strength of the blend membrane coagulated by alkali aqueous solution was enhanced, corresponding to homogeneous structure and small pore size. However, blend membranes having a larger pore size (366 nm by SEM) and water permeability (560 ml/m² h mmHg) were obtained by coagulating the cellulose/KGM (70:30) cuprammonium solution with 40°C water, where ca. 20% of KGM as pore former were removed from the membrane.     

Cellulose acetate and polyetherimide blend ultrafiltration membranes: II. Effect of additive

Ultrafiltration membranes are largely applied in the separation of heavy metal ion and macromolecular solutes from aqueous streams. Studies are presented on ultrafiltration blend membranes, based on cellulose acetate (CA) and polyetherimide (PEI) in various blend compositions. Polyethylene glycol (PEG 600) was employed as a non‐solvent additive in various concentrations to the casting solution to improve the ultrafiltration performance of the resulting membranes. The blend membranes prepared were characterized in terms of compaction time, pure water flux (PWF), water content, membrane resistance, and scanning electron microscopy (SEM). The molecular weight cut‐off (MWCO) obtained from the protein separation studies is also reported. Applications of these membranes for separating toxic metal ions from aqueous streams are discussed. Copyright © 2007 John Wiley & Sons, Ltd.     

耗散粒子动力学模拟Nafion膜和PVA/Nafion共混膜的介观结构

采用耗散粒子动力学模拟方法研究了水化Nafion膜和水化聚乙烯醇(PVA)/Nafion共混膜的微结构.模拟结果表明水化Nafion膜和水化PVA/Nafion共混膜均能形成相分离的微结构.在水化Nafion膜中,水与磺酸根混合形成管状的水团簇.随着膜内水含量增多,管状水团簇的尺寸逐渐变大并在膜内形成连续的水通道.在水化PVA/Nafion共混膜中,PVA、水、磺酸根混合形成亲水性区域.共混膜中PVA的质量分数和水含量共同影响膜的微结构.当膜中PVA质量分数较低时,PVA主要分布在Nafion的磺酸根基团周围;PVA质量分数升高后,PVA会在膜内单独成一相.当膜中的水含量相对较低时,水分子会溶解于PVA中,此时膜内不存在单独的水团簇;膜中的水含量增多后,膜内会形成接近于球形的水团簇.本文工作可为直接甲醇燃料电池用的PVA改性Nafion膜的开发提供参考.     

Preparation of high density polyethylene/polyethylene-block-poly(ethylene glycol) copolymer blend porous membranes via thermally induced phase separation process and their properties

<正>High density polyethylene(HDPE)/polyethylene-block-poly(ethylene glycol)(PE-b-PEG) blend porous membranes were prepared via thermally induced phase separation(TIPS) process using diphenyl ether(DPE) as diluent.The phase diagrams of HDPE/PE-b-PEG/DPE systems were determined by optical microscopy and differential scanning calorimetry(DSC).By varying the content of PE-b-PEG,the effects of PE-b-PEG copolymer on morphology and crystalline structure of membranes were studied by scanning electron microscopy(SEM) and wide angle X-ray diffraction(WAXD). The chemical compositions of whole membranes and surface layers were characterized by elementary analysis,Fourier transform infrared spectroscopy-attenuated total reflection(FTIR-ATR) and X-ray photoelectron spectroscopy(XPS).Water contact angle,static protein adsorption and water flux experiments were used to evaluate the hydrophilicity,antifouling and water permeation properties of the membranes.It was found that the addition of PE-b-PEG increased the pore size of the obtained blend membranes.In the investigated range of PE-b-PEG content,the PEG blocks could not aggregate into obviously separated domains in membrane matrix.More importantly,PE-b-PEG could not only be retained stably in the membrane matrix during membrane formation,but also enrich at the membrane surface layer.Such stability and surface enrichment of PE-b-PEG endowed the blend membranes with improved hydrophilicity,protein absorption resistance and water permeation properties,which would be substantially beneficial to HDPE membranes for water treatment application.     

PREPARATION OF HIGH DENSITY POLYETHYLENE/POLYETHYLENE-ΒLOCK- POLY(ETHYLENE GLYCOL) COPOLYMER BLEND POROUS MEMBRANES VIA THERMALLY INDUCED PHASE SEPARATION PROCESS AND THEIR PROPERTIES

High density polyethylene (HDPE)/polyethylene-Wock-poly(ethylene glycol) (PE-b-PEG) blend porous membranes were prepared via thermally induced phase separation (TIPS) process using diphenyl ether (DPE) as diluent. The phase diagrams of HDPE/PE-b-PEG/DPE systems were determined by optical microscopy and differential scanning calorimetry (DSC). By varying the content of PE-b-PEG, the effects of PE-b-PEG copolymer on morphology and crystalline structure of membranes were studied by scanning electron microscopy (SEM) and wide angle X-ray diffraction (WAXD). The chemical compositions of whole membranes and surface layers were characterized by elementary analysis, Fourier transform infrared spectroscopy-attenuated total reflection (FTIR-ATR) and X-ray photoelectron spectroscopy (XPS). Water contact angle, static protein adsorption and water flux experiments were used to evaluate the hydrophilicity, antifouling and water permeation properties of the membranes. It was found that the addition of PE-b-PEG increased the pore size of the obtained blend membranes. In the investigated range of PE-b-PEG content, the PEG blocks could not aggregate into obviously separated domains in membrane matrix. More importantly, PE-b-PEG could not only be retained stably in the membrane matrix during membrane formation, but also enrich at the membrane surface layer. Such stability and surface enrichment of PE-b-PEG endowed the blend membranes with improved hydrophilicity, protein absorption resistance and water permeation properties, which would be substantially beneficial to HDPE membranes for water treatment application.     

侧链型含氟磺化聚醚砜/磺化聚酰亚胺共混质子交换膜的制备及性能

制备了一类侧链型含氟磺化聚醚砜(s SPFES)与磺化聚酰亚胺(SPI)共混质子交换膜(s SPFES/SPI),研究了其吸水率、尺寸变化、质子电导率及稳定性等性能.结果表明,2种磺化聚合物以三乙胺盐型溶液共混及铸膜时相容性良好,制备的s SPFES/SPI共混质子交换膜结构均一,透明结实,离子交换容量为1.76~1.88 mmol/g.s SPFES/SPI共混质子交换膜表现出横向低于纵向的各向异性尺寸变化特性,在60℃水中横向尺寸变化率低于10%,经140℃加压水处理24 h后仍能保持较好的机械强度,质量损失低于6.1%.当温度高于50℃时,完全水合状态下的s SPFES/SPI共混质子交换膜的质子电导率均达到0.1 S/cm.     

Improving hydrophilicity and protein resistance of poly(vinylidene fluoride) membranes by blending with amphiphilic hyperbranched-star polymer

To endow hydrophobic poly(vinylidene fluoride) (PVDF) membranes with reliable hydrophilicity and protein resistance, an amphiphilic hyperbranched-star polymer (HPE-g-MPEG) with about 12 hydrophilic arms in each molecule was synthesized by grafting methoxy poly(ethylene glycol) (MPEG) to the hyperbranched polyester (HPE) molecule using terephthaloyl chloride (TPC) as the coupling agent and blended with PVDF to fabricate porous membranes via phase inversion process. The chemical composition changes of the membrane surface were confirmed by X-ray photoelectron spectroscopy (XPS), and the membrane morphologies were measured by scanning electron microscopy (SEM). Water contact angle, static protein adsorption, and filtration experiments were used to evaluate the hydrophilicity and anti-fouling properties of the membranes. It was found that MPEG segments of HPE-g-MPEG enriched at the membrane surface substantially, while the water contact angle decreased as low as 49 degrees for the membrane with a HPE-g-MPEG/PVDF ratio of 3/10. More importantly, the water contact angle of the blend membrane changed little after being leached continuously in water at 60 degrees C for 30 days, indicating a quite stable presence of HPE-g-MPEG in the blend membranes. Furthermore, the blend membranes showed lower static protein adsorption, higher water and protein solution fluxes, and better water flux recovery after cleaning than the pure PVDF membrane.     

再生纤维素／聚乙烯醇共混膜的研究

由纤维素铜氨溶液与不同体积比（１－１０％）的聚乙烯醇（ＰＶＡ）水溶液共混制备了一系列再生纤维素共混膜．扫描电镜结果表明ＰＶＡ含量大于８％时，该共混膜产生明显相分离．当ＰＶＡ低于５％时，共混膜相容性较好．膜的结晶度，抗张强度，直角撕裂强度，断裂伸长及耐热性均优于单独用钢氨液制备的再生纤维素膜．此外，用流动速率法和超滤法测定了膜的孔径，渗透性及纯水通量，结果表明共混膜的孔性没有明显变化．本文得出：再生纤维素与５％ＰＶＡ共混能改善力学性能，并且能保持其生物降解性．     

Preparation and Performance of Polysulfone‐Cellulose Acetate Blend Ultrafiltration Membrane

In the development of high performance polymeric membranes, it is essential to design the molecular and morphological characteristics for specific applications. Polysulfone and cellulose acetate of blend membranes with various concentration of polymer pore former, PEG600 were prepared by phase inversion technique and used for ultrafiltration. Polymer blend composition, additive concentration, and casting conditions were optimized. The blend membranes were characterized in terms of compaction, pure water flux, water content, hydraulic resistance and separation of dextran studies. Surface morphology of the embranes was analyzed using scanning electron microscopy at different magnifications. Further, the characterized membranes were attempted for treatment of distillery effluents after secondary treatment and the results are discussed in detail.     

Preparation, characterization and effect of annealing on performance of cellulose acetate/sulfonated polysulfone and cellulose acetate/epoxy resin blend ultrafiltration membranes

Polymeric membranes based on cellulose acetate (CA)--sulfonated polysulfone blends at three different polymer compositions were prepared by solution blending and phase inversion technique, characterized and subjected to annealing at 70, 80 and 90 °C. The permeate water flux, separation of bovine serum albumin and its flux by the blend membranes before and after thermal treatment, have been compared and discussed. Similarly, CA and epoxy resin (diglycidyl ether of bisphenol-A) were blended in various compositions, in the presence and in the absence of polyethyleneglycol 600 as non-solvent additive, using N,N^′-dimethylformamide as solvent, and used for preparing ultraflltration membranes by phase inversion technique. The polymer blend composition, additive concentration, casting and gelation conditions were optimized. Blend membranes were characterized in terms of compaction, pure water flux, water content and membrane resistance. The effects of polymer blend composition and additive concentration on the above parameters were determined and the results are discussed.     

Protein-adsorption-resistance and permeation property of polyethersulfone and soybean phosphatidylcholine blend ultrafiltration membranes

Novel ultrafiltration membranes were prepared by simple blending of polyethersulfone (PES) and soybean phosphatidylcholine (SPC). X-ray photoelectron spectroscopy (XPS) and water contact angle measurements indicated SPC enrichment at the membrane surfaces. The immobilization and arrangement of PC groups at surfaces rendered the membranes more hydrophilic. BSA adsorption amount decreased from 56.2 μg/cm² for SPC-free PES membrane to 2.4 μg/cm² for PES/SPC blend membrane. The fouling-resistant property of the blend membranes was improved considerably with an increase of SPC content while the pure water permeation flux decreased remarkably. Using PEG/PVP mixture instead of PEG as pore-forming agent increased pure water flux of PES/SPC blend membrane to some extent.     

HBPE-g-PVDF/PVDF blend nanofiltration membrane: preparation and characterization

Hyperbranched polyester-grafted poly(vinylidene fluoride) (HBPE-g-PVDF) was synthesized and used as additive in preparation of PVDF blend membranes. HBPE-g-PVDF copolymer was characterized with FTIR and TGA techniques. The prepared membranes were also characterized with SEM, AFM and contact angle measurement. The performance of prepared membranes as nanofiltration membrane was studied by pure water flux (PWF), salt rejection, dynamic and static fouling tests. The results showed that hydrophilicity of prepared membranes greatly increased after blending, and their pore size and pore size distribution and so PWF of blend membranes increased.