Thermal Analysis of Binary Mixtures of Imidazolium,Pyridinium, Pyrrolidinium,and Piperidinium Ionic Liquids

Ionic liquids (ILs) are being widely studied due to their unique properties, which make them potential candidates for conventional solvents. To study whether binary mixtures of pure ionic liquids provide a viable alternative to pure ionic liquids for different applications, in this work, the thermal analysis and molar heat capacities of five equimolar binary mixtures of ionic liquids based on imidazolium, pyridinium, pyrrolidinium, and piperidinium cations with dicyanamide, trifluoromethanesulfonate, and bis(trifluoromethylsulfonyl)imide anions have been performed. Furthermore, two pure ionic liquids based on piperidinium cation have been thermally characterized and the heat capacity of one of them has been measured. The determination and evaluation of both the transition temperatures and the molar heat capacities was carried out using differential scanning calorimetry (DSC). It was observed that the thermal behavior of the mixtures was completely different than the thermal behavior of the pure ionic liquids present, while the molar heat capacities of the binary mixtures were very similar to the value of the average of molar heat capacities of the two pure ionic liquids.     

Synthesis and Characterization of Ammonium-, Pyridinium-, and Pyrrolidinium-Based Sulfonamido Functionalized Ionic Liquids

New homologous ammonium-, pyridinium-, and pyrrolidinium-based sulfonamido functionalized ionic liquids have been synthesized in two steps using monoethanolamine, methanesulfonyl chloride, and tosyl chloride as precursors with ethanol as solvent. Attempts to synthesize dual amino functionalized ionic liquid containing both a primary and a secondary amine group in the same ionic liquid are also reported. All functionalized ionic liquids were characterized by ¹H and ¹³C NMR. Melting point and thermal stability of the functionalized ionic liquids were measured by differential scanning calorimetry and thermogravimetric analysis.     

有机-无机杂化聚离子液体材料制备及其对染料吸附性能的评价

以烯丙基三乙氧基硅烷与1-乙烯基-3-辛基咪唑溴盐离子液体为单体通过自由基聚合及溶胶-凝胶制备了有机-无机杂化聚离子液体材料。通过红外光谱和扫描电镜对所制备的杂化聚离子液体材料进行了表征,并考察了其对柠檬黄、日落黄、苋菜红以及诱惑红等常见染料的吸附性能。研究结果表明:所制备的聚离子液体材料对日落黄和诱惑红具有优异的吸附性能,其吸附容量分别为29.20和86.17 mg/g;当吸附时间为5 min时,该材料对诱惑红和日落黄的吸附分别达到平衡时吸附量的87.5%和72.8%,显示了较快的吸附速率。     

Ionic liquids. Combination of combustion calorimetry with high-level quantum chemical calculations for deriving vaporization enthalpies

In this work, the molar enthalpies of formation of the ionic liquids [C2MIM][NO3] and [C4MIM][NO3] were measured by means of combustion calorimetry. The molar enthalpy of fusion of [C2MIM][NO3] was measured using differential scanning calorimetry. Ab initio calculations of the enthalpy of formation in the gaseous phase have been performed for the ionic species using the G3MP2 theory. We have used a combination of traditional combustion calorimetry with modern high-level ab initio calculations in order to obtain the molar enthalpies of vaporization of a series of the ionic liquids under study.     

Thermal, rheological, and ion-transport properties of phosphonium-based ionic liquids

Phosphonium-based ionic liquids with varying counteranions from commercially available ionic liquid precursors enabled tunable viscosity, ionic conductivity, and thermal stability. Thermogravimetric analysis revealed a relationship between thermal stability and anion composition where anions with lower basicity remained stable to higher temperatures. Determination of glass transition temperatures and melting temperatures using differential scanning calorimetry revealed supercooling, crystallization, and dependence on anion composition. Rheological and ionic conductivity measurements determined the temperature-dependence of the viscosity and ionic conductivity of the phosphonium-based ionic liquids. Arrhenius analyses of conductivity and viscosity provided activation energies, which showed a decrease toward larger, more delocalized anions. An assessment according to the Walden plot displayed their efficacy relative to other ionic liquids.     

Preparation of magnetic chitosan and graphene oxide-functional guanidinium ionic liquid composite for the solid-phase extraction of protein

A series of novel cationic functional hexaalkylguanidinium ionic liquids and anionic functional tetraalkylguanidinium ionic liquids have been synthesized, and then magnetic chitosan graphene oxide (MCGO) composite has been prepared and coated with these functional guanidinium ionic liquids to extract protein by magnetic solid-phase extraction. MCGO-functional guanidinium ionic liquid has been characterized by vibrating sample magnetometer, field emission scanning electron microscopy, X-ray diffraction spectrometer and Fourier transform infrared spectrometer. After extraction, the concentrations of protein were determined by measuring the absorbance at 278 nm using an ultra violet visible spectrophotometer. The advantages of MCGO-functional guanidinium ionic liquid in protein extraction were compared with magnetic chitosan, graphene oxide, MCGO and MCGO-ordinary imidazolium ionic liquid. The proposed method has been applied to extract trypsin, lysozyme, ovalbumin and bovine serum albumin. A comprehensive study of the adsorption conditions such as the concentration of protein, the amount of MCGO-functional guanidinium ionic liquid, the pH, the temperature and the extraction time were also presented. Moreover, the MCGO-functional guanidinium ionic liquid can be easily regenerated, and the extraction capacity was about 94% of the initial one after being used three times.     

Ambient isobaric heat capacities, C(p,m), for ionic solids and liquids: an application of volume-based thermodynamics (VBT)

Thermodynamic properties, such as standard entropy, among others, have been shown to correlate well with formula volume, V(m), thus permitting prediction of these properties on the basis of chemical formula and density alone, with no structural detail required. We have termed these procedures "volume-based thermodynamics" (VBT). We here extend these studies to ambient isobaric heat capacities, C(p,m), of a wide range of materials. We show that heat capacity is strongly linearly correlated with formula volume for large sets of minerals, for ionic solids in general, and for ionic liquids and that the results demonstrate that the Neumann-Kopp rule (additivity of heat capacity contributions per atom) is widely valid for ionic materials, but the smaller heat capacity contribution per unit volume for ionic liquids is noted and discussed. Using these correlations, it is possible to predict values of ambient (298 K) heat capacities quite simply. We also show that the heat capacity contribution of water molecules of crystallization is remarkably constant, at 41.3 ± 4.7 J K(-1) (mol of water)(-1), so that the heat capacities of various hydrates may be reliably estimated from the values of their chemical formula neighbors. This result complements similar observations that we have reported for other thermodynamic differences of hydrates.     

The ionic parachor and predicting properties of amino acid ionic liquid homologues of 1-alkyl-3-methylimidazolium glycine

The amino acid ionic liquids(AAILs) [C3mim][Gly](1-propyl-3-methylimidazolium glycine) and [C4mim][Gly](1-butyl-3methylimidazolium glycine) have been prepared by the neutralization method and characterized by 1 H NMR spectroscopy and differential scanning calorimetry(DSC).The values of their density,surface tension and refractive index were measured at(298.15 ± 0.05) K.Since the AAILs can form strong hydrogen bonds with water,small amounts of water are difficult to remove from the AAILs by common methods.In order to eliminate the effect of the impurity water,the standard addition method(SAM) was applied to these measurements.A new concept which is called the ionic parachor has been put forward.The [C n mim] + cations were treated as a group of reference ions and the individual values of their ionic parachor were evaluated in terms of an extrathermodynamic assumption.Then,using the values of the ionic parachor of reference ions,the parachor,surface tension γ and refractive index n D of the ionic liquids investigated in this work were estimated.The estimated values correlate quite well with the corresponding experimental values.     

Imidazolium 2‐Substituted 4,5‐Dicyanoimidazolate Ionic Liquids: Synthesis,Crystal Structures and Structure–Thermal Property Relationships

Thirty six novel ionic liquids (ILs) with 1‐butyl‐3‐methylimidazolium and 3‐methyl‐1‐octylimidazolium cations paired with 2‐substitited 4,5‐dicyanoimidazolate anions (substituent at C2=chloro, bromo, methoxy, vinyl, amino, methyl, ethyl, propyl, isopropyl, butyl, pentyl, hexyl, heptyl, octyl, nonyl, decyl, undecyl and phenyl) have been synthesized and characterized by using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and single‐crystal X‐ray crystallography. The effects of cation and anion type and structure on the thermal properties of the resulting ionic liquids, including several room temperature ionic liquids (RTILs) are examined and discussed. ILs exhibited large liquid and crystallization ranges and formed glasses on cooling with glass transition temperatures in the range of ?22 to ?68 °C. The effects of alkyl substituents of the imidazolate anion reflected the crystallization, melting points and thermal decomposition of the ILs. The Coulombic packing force, van der Waals forces and size of the anions can be considered for altering the thermal transitions. Three crystal structures of the ILs were determined and the effects of changes to the cations and anions on the packing of the structure were investigated.     

Physicochemical properties and solubility of alkyl-(2-hydroxyethyl)-dimethylammonium bromide

Quaternary ammonium salts, which are precursors of ionic liquids, have been prepared from N,N-dimethylethanolamine as a substrate. The paper includes specific basic characterization of synthesized compounds via the following procedures: nuclear magnetic resonance (NMR) and Fourier transform infrared (FTIR) spectra, water content, mass spectroscopy (MS) spectra, temperatures of decompositions, basic thermodynamic properties of pure ionic liquids (the melting point, enthalpy of fusion, enthalpy of solid-solid phase transition, glass transition), and the difference in the solute heat capacity between the liquid and solid at the melting temperature determined by differential scanning calorimetry (DSC). The (solid + liquid) phase equilibria of binary mixtures containing (quaternary ammonium salt + water, or + 1-octanol) has been measured by a dynamic method over wide range of temperatures, from 230 K to 560 K. These data were correlated by means of the UNIQUAC ASM and modified nonrandom two-liquid NRTL1 equations utilizing parameters derived from the (solid + liquid) equilibrium. The partition coefficient of ionic liquid in the 1-octanol/water binary system has been calculated from the solubility results. Experimental partition coefficients (log P) were negative at three temperatures.     

Design of guanidinium ionic liquid based microwave‐assisted extraction for the efficient extraction of Praeruptorin A from Radix peucedani

A series of novel tetramethylguanidinium ionic liquids and hexaalkylguanidinium ionic liquids have been synthesized based on 1,1,3,3‐tetramethylguanidine. The structures of the ionic liquids were confirmed by ¹H NMR spectroscopy and mass spectrometry. A green guanidinium ionic liquid based microwave‐assisted extraction method has been developed with these guanidinium ionic liquids for the effective extraction of Praeruptorin A from Radix peucedani. After extraction, reversed‐phase high‐performance liquid chromatography with UV detection was employed for the analysis of Praeruptorin A. Several significant operating parameters were systematically optimized by single‐factor and L₉ (3⁴) orthogonal array experiments. The amount of Praeruptorin A extracted by [1,1,3,3‐tetramethylguanidine]CH₂CH(OH)COOH is the highest, reaching 11.05 ± 0.13 mg/g. Guanidinium ionic liquid based microwave‐assisted extraction presents unique advantages in Praeruptorin A extraction compared with guanidinium ionic liquid based maceration extraction, guanidinium ionic liquid based heat reflux extraction and guanidinium ionic liquid based ultrasound‐assisted extraction. The precision, stability, and repeatability of the process were investigated. The mechanisms of guanidinium ionic liquid based microwave‐assisted extraction were researched by scanning electron microscopy and IR spectroscopy. All the results show that guanidinium ionic liquid based microwave‐assisted extraction has a huge potential in the extraction of bioactive compounds from complex samples.     

Protein stability in an ionic liquid milieu: on the use of differential scanning fluorimetry

Protein stability is a major bottleneck in the biotechnological application of ionic liquid-containing solvents, either in the frame of biocatalysis or protein storage. Herein, differential scanning fluorimetry was successfully implemented as a high throughput method to fast scan the impact of a number of cholinium-based ionic liquids on the stability of proteins.     

The influence of hydrogen bonding on the physical properties of ionic liquids

Potential applications of ionic liquids depend on the properties of this class of liquid material. To a large extent the structure and properties of these Coulomb systems are determined by the intermolecular interactions among anions and cations. In particular the subtle balance between Coulomb forces, hydrogen bonds and dispersion forces is of great importance for the understanding of ionic liquids. The purpose of the present paper is to answer three questions: Do hydrogen bonds exist in these Coulomb fluids? To what extent do hydrogen bonds contribute to the overall interaction between anions and cations? And finally, are hydrogen bonds important for the physical properties of ionic liquids? All these questions are addressed by using a suitable combination of experimental and theoretical methods including newly synthesized imidazolium-based ionic liquids, far infrared spectroscopy, terahertz spectroscopy, DFT calculations, differential scanning calorimetry (DSC), viscometry and quartz-crystal-microbalance measurements. The key statement is that although ionic liquids consist solely of anions and cations and Coulomb forces are the dominating interaction, local and directional interaction such as hydrogen bonding has significant influence on the structure and properties of ionic liquids. This is demonstrated for the case of melting points, viscosities and enthalpies of vaporization. As a consequence, a variety of important properties can be tuned towards a larger working temperature range, finally expanding the range of potential applications.     

Biased spectroscopic protein quantification in the presence of ionic liquids

Owing to their unique physicochemical properties, ionic liquids have gained much recognition as solvents or co-solvents in a wide variety of biochemical applications. In the context of protein analytics, four similar 1-alkyl-3-methylimidazolium-based ionic liquids have been analysed for their applicability as co-solvents. Spectroscopic bovine serum albumin (BSA) quantification experiments in the presence of ionic liquids were performed and for two ionic liquids a concentration-dependent effect has been found that can lead to biased protein quantification. It could be shown that the biased spectroscopic analysis of the tested ionic liquids is dependent on the length of the alkyl side chain (>C₄) of the 1-alkyl-3-methylimidazolium-based cation, and the chaotropicity of the anion. Once accounted for and properly calibrated when using spectroscopic methods, these effects can be avoided thus facilitating correct protein quantification in the presence of ionic liquids.     

Experimental and Theoretical Study of Two Pyridinium-Based Ionic Liquids

Thermophysical properties of two pyridinium-based ionic liquids, 1-ethyl-2-methylpyridinium bis(trifluoromethylsulfonyl)imide and 1-propyl-2-methylpyridinium bis(trifluoromethylsulfonyl)imide, have been measured from 278.15 to 323.15?K, with a temperature step of 2.5?K. The properties measured were: densities, speeds of sound, refractive indices, surface tensions, isobaric molar heat capacities, electrical conductivities and viscosities. Thermal properties were also recorded in the temperature range from 100 to 320?K. From the experimental results coefficients of thermal expansion, isentropic compressibilities, molar refraction and surface enthalpies and entropies have been determined. Moreover, a theoretical study has been performed using ab initio calculations, level of theory HF/6-31G(d). From this study, we have obtained qualitative information about the magnitude and the directionality of the cation?Canion interactions which allows a better understanding of the physico-chemical properties of these ionic liquids.     

Atom transfer radical polymerization of styrenic ionic liquid monomers and carbon dioxide absorption of the polymerized ionic liquids

Polymeric forms of ionic liquids have many potential applications because of their high thermal stability and ionic nature. Two ionic liquid monomers, 1‐(4‐vinylbenzyl)‐3‐butyl imidazolium tetrafluoroborate (VBIT) and 1‐(4‐vinylbenzyl)‐3‐ butyl imidazolium hexafluorophosphate (VBIH), were synthesized through the quaternization of N‐butylimidazole with 4‐vinylbenzylchloride and a subsequent anion‐ exchange reaction with sodium tetrafluoroborate or potassium hexafluorophosphate. Copper‐mediated atom transfer radical polymerization was used to polymerize VBIT and VBIH. The effects of various initiator/catalyst systems, monomer concentrations, solvent polarities, and reaction temperatures on the polymerization were examined. The polymerization was well controlled and exhibited living characteristics when CuBr/1,1,4,7,10,10‐hexamethyltriethylenetetramine or CuBr/2,2′‐bipyridine was used as the catalyst and ethyl 2‐bromoisobutyrate was used as the initiator. Characterizations by thermogravimetric analysis, differential scanning calorimetry, and X‐ray diffraction showed that the resulting VBIT polymer, poly[1‐(4‐vinylbenzyl)‐3‐butyl imidazolium tetrafluoroborate] (PVBIT), was amorphous and had excellent thermal stability, with a glass‐transition temperature of 84 °C. The polymerized ionic liquids could absorb CO₂ as ionic liquids: PVBIT absorbed 0.30% (w/w) CO₂ at room temperature and 0.78 atm. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1432–1443, 2005     

Synthesis and characterization of novel chiral imidazolium and pyridinium ionic liquids derived from tartaric acid and 2-oxazolidinone

Abstract

Novel chiral imidazolium and pyridinium ionic liquids based on tartaric acid and 2-oxazolidinone were designed. Symmetrical dicationic ionic liquids based on tartaric acid have been synthesized and characterized. These chiral ionic liquids were designed by employing very short and simple methods. Incorporation of alkyl halide over tartaric acid and 2-oxazolidinone is an important step. N-methyl imidazole and pyridine were used for preparation of quaternary salts. These ionic liquids have been evaluated for the asymmetric sulfide oxidation. Chiral ionic liquids based on tartaric acid showed superior chiral inducing property as compare to 2-oxazolidinone based chiral ionic liquids.     

Physico-chemical properties and phase behaviour of piperidinium-based ionic liquids

The sufficient review of the existing literature of the 1-alkyl-1-methylppiperidinium-based ionic liquids has been presented. The phase diagrams for the binary systems of {1-butyl-1-methylpiperidinium thiocyanate [BMPIP][SCN] + an alcohol (1-hexanol, 1-heptanol, 1-octanol, 1-nonanol, 1-decanol, 1-dodecanol), or + water, or + aliphatic hydrocarbons (n-hexane, n-heptane, n-octane), or + cyclohexane, or, + cycloheptane, or + aromatic hydrocarbons (benzene, toluene, ethylbenzene)} and for the binary systems of {1-ethyl-1-methylpiperidinium bis{(trifluoromethyl)sulfonyl}imide [EMPIP][NTf₂] + an alcohol (ethanol, 1-propanol, 1-butanol, 1-hexanol, 1-heptanol, 1-octanol, 1-nonanol), or + water} have been determined at atmospheric pressure using a dynamic method. The influence of an alcohol chain length was discussed for these ionic liquids. A systematic decrease in the solubility was observed with an increase of the alkyl chain length of an alcohol. (Solid + liquid) phase equilibria with complete miscibility in the liquid phase region were observed for the systems involving water and the alcohols for the thiocyanate-based ionic liquid. Opposite, the bis{(trifluoromethyl)sulfonyl}imide-based ionic liquid reveal the immiscibility gap in the liquid phase. The correlation of the experimental data has been carried out using the NRTL equation. The phase diagrams reported here have been compared to the systems published earlier with the 1-alkyl-1-methylpiperidinium-based ionic liquids. The influence of the cation and anion on the phase behaviour has been discussed. The basic thermal properties of pure ILs, i.e. melting temperature and the enthalpy of fusion, the solid-solid phase transition temperature and enthalpy have been measured using a differential scanning microcalorimetry technique.     

Synthesis of 2,2'-biimidazolium-based ionic liquids: use as a new reaction medium and ligand for palladium-catalyzed suzuki cross-coupling reactions

Neat reactions of 2,2'-biimidazole with an excess of alkyl or polyfluoroalkyl iodides at 140 degrees C, followed by anion exchange with LiN(SO(2)CF(3))(2) or KPF(6), gave the diquaternary salts 3a-k in >80% yields. However, by controlling the reaction stoichiometry, 2,2'-biimidazole can also be monoquaternized with the same electrophiles at 100 degrees C under similar conditions. Subsequent metathesis reactions with LiN(SO(2)CF(3))(2) or KPF(6) resulted in the ionic liquids 4a-m in high yields. Thermal properties were determined with a differential scanning calorimeter (DSC) and a thermogravimetric analyzer (TGA). Most of the monoquaternary salts are room-temperature ionic liquids. 1,3,1'-Tributyl-2,2'-biimidazolium hexafluorophosphate was demonstrated to be an excellent solvent and ligand for palladium-catalyzed Suzuki cross-coupling reactions. The catalytic ionic liquid system may be recycled at least 14 times without a significant decrease in catalytic performance.     

色谱分析中离子液体的应用及其测定

离子液体作为一种优良的溶剂越来越受到人们的关注。由于离子液体特殊的物理化学性质使其在色谱分析中也得到了较广泛的应用。本文综述了离子液体在气相色谱、高效液相色谱和毛细管电泳中的应用,其中包括离子液体作为气相色谱的固定相、高效液相色谱的固定相及流动相添加剂和毛细管电泳的电解质添加剂等,并对离子液体的色谱分离检测作了详细介绍。