Phase equilibria for H2 + CO2 + H2O system containing gas hydrates

Isothermal phase equilibrium (pressure–composition in the gas phase) for the ternary system of H₂ + CO₂ + H₂O has been investigated in the presence of gas hydrate phase. Three-phase equilibrium pressure increases with the H₂ composition of gas phase. The Raman spectra suggest that H₂ is not enclathrated in the hydrate-cages and behaves only like the diluent gas toward the formation of CO₂ hydrate. This fact is also supported by the thermodynamic analysis using Soave–Redlich–Kwong equation of state.     

(Liquid + solid) metastable equilibria in quinary system Li2CO3 + Na2CO3 + K2CO3 + Li2B4O7 + Na2B4O7 + K2B4O7 + H2O at T=288 K for Zhabuye salt lake

An experimental study on metastable equilibria at T=288 K in the quinary system Li₂CO₃ + Na₂CO₃ + K₂CO₃ + Li₂B₄O₇ + Na₂B₄O₇ + K₂B₄O₇ + H₂O was done by isothermal evaporation method. Metastable equilibrium solubilities and densities of the solution were determined experimentally. According to the experimental data, the metastable equilibrium phase diagram under the condition saturated with Li₂CO₃ was plotted, in which there are four invariant points; nine univariant curves; six fields of crystallization: K₂CO₃ · 3/2H₂O, K₂B₄O₇ · 5H₂O, Li₂B₂O₄ · 16H₂O, Na₂B₂O₄ · 8H₂O, Na₂CO₃ · 10H₂O, NaKCO₃ · 6H₂O. Some differences were found between the stable phase diagram at T=298 K and the metastable one at T=288 K.     

Experimental investigation of incipient equilibrium conditions for the formation of semi-clathrate hydrates from quaternary mixtures of (CO2 + N2 + TBAB + H2O)

The three-phase (vapour + liquid + solid) equilibrium conditions for semi-clathrates formed from three mixtures of (CO₂ + N₂), in aqueous solutions of tetra-butyl ammonium bromide (TBAB), were measured in an isochoric reactor. The experiments were conducted at temperatures between (281 and 290) K, at pressures between (1.9 and 5.9) MPa and in aqueous TBAB solutions of w_TBAB = (0.05, 0.10, and 0.20). The experimental results obtained in this study were compared with previously obtained results for gas hydrates, formed from the same three mixtures of (CO₂ + N₂) and it was observed that semi-clathrates formed at a substantially lower pressure than did gas hydrates.     

The precise measurement of the (vapour + liquid) equilibrium properties for (CO2 + isobutane) binary mixtures

Recently, it has been suggested that natural working fluids, such as CO₂, hydrocarbons, and their mixtures, could provide a long-term alternative to fluorocarbon refrigerants. (Vapour + liquid) equilibrium (VLE) data for these fluids are essential for the development of equations of state, and for industrial process such as separation and refinement. However, there are large inconsistencies among the available literature data for (CO₂ + isobutane) binary mixtures, and therefore provision of reliable and new measurements with expanded uncertainties is required. In this study, we determined precise VLE data using a new re-circulating type apparatus, which was mainly designed by Akico Co., Japan. An equilibrium cell with an inner volume of about 380 cm³ and two optical windows was used to observe the phase behaviour. The cell had re-circulating loops and expansion loops that were immersed in a thermostatted liquid bath and air bath, respectively. After establishment of a steady state in these loops, the compositions of the samples were measured by a gas chromatograph (GL Science, GC-3200). The VLE data were measured for CO₂/propane and CO₂/isobutane binary mixtures within the temperature range from 300 K to 330 K and at pressures up to 7 MPa. These data were compared with the available literature data and with values predicted by thermodynamic property models.     

Study of bromide salts solubility in the (m1NaBr + m2MgBr2)(aq) system at T = 323.15 K. Thermodynamic model of solution behavior and (solid + liquid) equilibria in the (Na + K + Mg + Br + H2O) system to high concentration and temperature

The bromide minerals solubility in the mixed system (m₁NaBr + m₂MgBr₂)(aq) have been investigated at T = 323.15 K by the physico-chemical analysis method. The equilibrium crystallization of NaBr·2H₂O(cr), NaBr(cr), and MgBr₂·6H₂O(cr) has been established. The solubility-measurements results obtained have been combined with all other experimental equilibrium solubility data available in literature at T = (273.15 and 298.15) K to construct a chemical model that calculates (solid + liquid) equilibria in the mixed system (m₁NaBr + m₂MgBr₂)(aq). The solubility modeling approach based on fundamental Pitzer specific interaction equations is employed. The model gives a very good agreement with bromide salts equilibrium solubility data. Temperature extrapolation of the mixed system model provides reasonable mineral solubility at high temperature (up to 100 °C). This model expands the previously published temperature variable sodium–potassium–bromide and potassium–magnesium–bromide models by evaluating sodium–magnesium mixing parameters. The resulting model for quaternary system (Na + K + Mg + Br + H₂O) is validated by comparing solubility predictions with those given in literature, and not used in the parameterization process. Limitations of the mixed solution models due to data insufficiencies at high temperature are discussed.     

The partition coefficients of ethylene between vapor and hydrate phase for methane + ethylene + THF + water systems

The vapor-hydrate equilibria were studied experimentally in detail for CH₄ + C₂H₄ + tetrahydrofuran (THF) + water systems in the temperature range of 273.15–282.15 K, pressure range of 2.0–4.5 MPa, the initial gas–liquid volume ratio range of 45–170 standard volumes of gas per volume of liquid and THF concentration range of 4–12 mol%. The results demonstrated that, because of the presence of THF, ethylene was remarkably enriched in vapor phase instead of being enriched in hydrate phase for CH₄ + C₂H₄ + water system. This conclusion is of industrial significance; it implies that it is feasible to enrich ethylene from gas mixture, e.g., various kinds of refinery gases or cracking gases in ethylene plant, by forming hydrate.     

(Solid + liquid) isothermal evaporation phase equilibria in the aqueous ternary system (Li2SO4 + MgSO4 + H2O) at T = 308.15 K

The solubility and the density in the aqueous ternary system (Li₂SO₄ + MgSO₄ + H₂O) at T = 308.15 K were determined by the isothermal evaporation. Our experimental results permitted the construction of the phase diagram and the plot of density against composition. It was found that there is one eutectic point for (Li₂SO₄ · H₂O + MgSO₄ · 7H₂O), two univariant curves, and two crystallization regions corresponding to lithium sulphate monohydrate (Li₂SO₄ · H₂O) and epsomite (MgSO₄ · 7H₂O). The system belongs to a simple co-saturated type, and neither double salts nor solid solution was found. Based on the Pitzer ion-interaction model and its extended HW models of aqueous electrolyte solution, the solubility of the ternary system at T = 308.15 K has been calculated. The predicted solubility agrees well with the experimental values.     

Phase behavior of (CO2 + methanol + lauric acid) system

In this study the phase equilibrium behaviors of the binary system (CO₂ + lauric acid) and the ternary system (CO₂ + methanol + lauric acid) were determined. The static synthetic method, using a variable-volume view cell, was employed to obtain the experimental data in the temperature range of (293 to 343) K and pressures up to 24 MPa. The mole fractions of carbon dioxide were varied according to the systems as follows: (0.7524 to 0.9955) for the binary system (CO₂ + lauric acid); (0.4616 to 0.9895) for the ternary system (CO₂ + methanol + lauric acid) with a methanol to lauric acid molar ratio of (2:1); and (0.3414 to 0.9182) for the system (CO₂ + methanol + lauric acid) with a methanol to lauric acid molar ratio of (6:1). For these systems (vapor + liquid), (liquid + liquid), (vapor + liquid + liquid), and (solid + fluid) transitions were observed. The phase equilibrium data obtained for the systems were modeled using the Peng–Robinson equation of state with the classical van der Waals mixing rule with a satisfactory correlation between experimental and calculated values.     

Measuring the solubility of CO2 and H2S in sulfolane and the density and viscosity of saturated liquid binary mixtures of (sulfolane + CO2) and (sulfolane + H2S)

The density and viscosity of liquid sulfolane saturated (loaded) with single CO₂ and H₂S gases were measured simultaneously with the solubility of the single CO₂ and H₂S gases in sulfolane at temperatures ranging from (303.15 to 363.15) K and pressures of up to about 2.4 MPa using a new experimental set-up developed in our laboratory. The experimental density and viscosity values were correlated using a modified Setchenow-type equation. It was observed that the density and viscosity of mixtures decrease by increasing temperature and acid gas solubility (loading) in sulfolane. Acid gas loading has a much profounder effect on the viscosity of solutions than on their density, i.e. at a concentration of 1 mol CO₂/H₂S per kg of sulfolane the density decreases by less than 3%, but viscosity decreases by more than 30%. Results show that at fixed temperature and pressure H₂S is more than four times as soluble as CO₂ in sulfolane. The measured solubility and density values were respectively used to obtain Henry’s law constants and partial molar volumes at infinite dilution for dissolution of CO₂ and H₂S gases in the liquid sulfolane at the temperatures studied. The Henry’s law constants obtained at different temperatures were used to determine infinite dilution partial molar thermodynamic functions (Gibbs free energy, enthalpy and entropy) of solution. The measured solubility data were correlated by using a model comprised of the extended Henry’s law and the Pitzer’s virial expansion for the excess Gibbs free energy.     

Thermodynamic study of the system (LiCl + LiNO3 + H2O)

The solubility of the binary system (LiNO₃ + H₂O) from T = 273.15 K to T = 333.15 K and solubility isotherms of the ternary system (LiCl + LiNO₃ + H₂O) were elaborately measured at T = 273.15 K and T = 323.15 K. These solubility data, as well as water activities in the binary systems from the literature, were treated by an empirically modified BET model. The isotherms of the ternary system (LiCl + LiNO₃ + H₂O) were reproduced and a complete phase diagram of the ternary system in the temperature range from 273.15 K to 323.15 K predicted. It is shown that the solubility data for the binary system (LiNO₃ + H₂O) measured in this work are slightly different from the literature data. Simulated results showed that the saturated salt solution of (2.8LiCl + LiNO₃) is in equilibrium with the stable solid phase LiNO₃(s) over the temperature range from 283.15 K to 323.15 K, other than the solid phases LiNO₃ · 3H₂O(s) and LiClH₂O(s) as reported by Iyoki et al. [S. Iwasaki, Y. Kuriyama. T. Uemura, J. Chem. Eng. Data 38 (1993) 396–398].     

Measurement and modeling of high-pressure (vapour + liquid) equilibria of (CO2 + alcohol) binary systems

An apparatus based on a static-analytic method assembled in this work was utilized to perform high pressure (vapour + liquid) equilibria measurements with uncertainties estimated at <5%. Complementary isothermal (vapour + liquid) equilibria results are reported for the (CO₂ + 1-propanol), (CO₂ + 2-methyl-1-propanol), (CO₂ + 3-methyl-1-butanol), and (CO₂ + 1-pentanol) binary systems at temperatures of (313, 323, and 333) K, and at pressure range of (2 to 12) MPa. For all the (CO₂ + alcohol) systems, it was visually monitored to insure that there was no liquid immiscibility at the temperatures and pressures studied. The experimental results were correlated with the Peng–Robinson equation of state using the quadratic mixing rules of van der Waals with two adjustable parameters. The calculated (vapour + liquid) equilibria compositions were found to be in good agreement with the experimental values with deviations for the mol fractions <0.12 and <0.05 for the liquid and vapour phase, respectively.     

Isopiestic measurement and solubility evaluation of the ternary system (CaCl2 + SrCl2 + H2O) at T = 298.15 K

Water activities in the ternary system (CaCl₂ + SrCl₂ + H₂O) and its sub-binary system (CaCl₂ + H₂O) at T = 298.15 K have been elaborately measured by an isopiestic method. The data of the measured water activity were used to justify the reliability of solubility isotherms reported in the literature by correlating them with a thermodynamic Pitzer–Simonson–Clegg (PSC) model. The model parameters for representing the thermodynamic properties of the (CaCl₂ + H₂O) system from (0 to 11) mol ⋅ kg⁻¹ at T = 298.15 K were determined, and the experimental water activity data in the ternary system were compared with those predicted by the parameters determined in the binary systems. Their agreement indicates that the PSC model parameters can reliably represent the properties of the ternary system. Under the assumption that the equilibrium solid phases are the pure solid phases (SrCl₂ ⋅ 6H₂O and CaCl₂ ⋅ 6H₂O)_(s) or the ideal solid solution consisting of CaCl₂ ⋅ 6H₂O_(s) and SrCl₂ ⋅ 6H₂O_(s), the solubility isotherms were predicted and compared with experimental data from the literature. It was found that the predicted solubility isotherm agrees with experimental data over the entire concentration range at T = 298.15 K under the second assumption described above; however, it does not under the first assumption. The modeling results reveal that the solid phase in equilibrium with the aqueous solution in the ternary system is an ideal solid solution consisting of SrCl₂ ⋅ 6H₂O_(s) and CaCl₂ ⋅ 6H₂O_(s). Based on the theoretical calculation, the possibility of the co-saturated points between SrCl₂ ⋅ 6H₂O_(s) and the solid solution (CaCl₂ ⋅ 6H₂O + SrCl₂ ⋅ 6H₂O)_(s) and between CaCl₂ ⋅ 6H₂O_(s) and the solid solution (CaCl₂ ⋅ 6H₂O + SrCl₂ ⋅ 6H₂O)_(s), which were reported by experimental researchers, has been discussed, and the Lippann diagram of this system has been presented.     

Measurement and modeling of high-pressure (vapor + liquid) equilibria of (CO2 + alkanol) binary systems

Complementary isothermal (vapor + liquid) equilibria data are reported for the (CO₂ + 3-methyl-2-butanol), (CO₂ + 2-pentanol), and (CO₂ + 3-pentanol) binary systems at temperatures of (313, 323, and 333) K, and at pressure range of (2 to 11) MPa. For all (CO₂ + alcohol) systems, it was visually monitored that there was no liquid immiscibility at the temperatures and pressures studied. The experimental data were correlated with the Peng–Robinson equation of state using the quadratic mixing rules of van der Waals with two adjustable parameters. The calculated (vapor + liquid) equilibria compositions were found to be in good agreement with the experimental data with deviations for the mole fractions <8% and <2% for the liquid and vapor phase, respectively.     

Thermodynamic evaluation and optimization of the (NaCl + KCl + MgCl2 + CaCl2 + MnCl2 + FeCl2 + CoCl2 + NiCl2) system

A complete critical evaluation of all available phase diagram and thermodynamic data has been performed for all condensed phases of the (NaCl + KCl + MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) system, and optimized model parameters have been found. The (MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) subsystem has been critically evaluated in a previous article. The model parameters obtained for the binary subsystems can be used to predict thermodynamic properties and phase equilibria for the multicomponent system. The Modified Quasichemical Model was used for the molten salt phase, and the (MgCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) solid solution was modeled using a cationic substitutional model with an ideal entropy and an excess Gibbs free energy expressed as a polynomial in the component mole fractions. Finally, the (Na,K)(Mg,Ca,Mn,Fe,Co,Ni)Cl₃ and the (Na,K)₂(Mg,Mn,Fe,Co,Ni)Cl₄ solid solutions were modeled using the Compound Energy Formalism.     

Phase equilibrium data and thermodynamic modeling of the system (CO2 + biodiesel + methanol) at high pressures

The main objective of this work was to investigate the high pressure phase behavior of the binary systems {CO₂(1) + methanol(2)} and {CO₂(1) + soybean methyl esters (biodiesel)(2)} and the ternary system {CO₂(1) + biodiesel(2) + methanol(3)} were determined. Biodiesel was produced from soybean oil, purified, characterized and used in this work. The static synthetic method, using a variable-volume view cell, was employed to obtain the experimental data in the temperature range of (303.15 to 343.15) K and pressures up to 21 MPa. The mole fractions of carbon dioxide were varied according to the systems as follows: (0.2383 to 0.8666) for the binary system {CO₂(1) + methanol(2)}; (0.4201 to 0.9931) for the binary system {CO₂(1) + biodiesel(2)}; (0.4864 to 0.9767) for the ternary system {CO₂(1) + biodiesel(2) + methanol(3)} with a biodiesel to methanol molar ratio of (1:3); and (0.3732 to 0.9630) for the system {CO₂ + biodiesel + methanol} with a biodiesel to methanol molar ratio of (8:1). For these systems, (vapor + liquid), (liquid + liquid), (vapor + liquid + liquid) transitions were observed. The phase equilibrium data obtained for the systems were modeled using the Peng–Robinson equation of state with the classical van der Waals (PR-vdW2) and Wong-Sandler (PR–WS) mixing rules. Both thermodynamic models were able to satisfactorily correlate the phase behavior of the systems investigated and the PR–WS presented the best performance.     

Thermodynamic study of the system (LiCl + CaCl2 + H2O)

Solubility isotherms of the ternary system (LiCl + CaCl₂ + H₂O) were elaborately determined at T = (283.15 and 323.15) K. Several thermodynamic models were applied to represent the thermodynamic properties of this system. By comparing the predicted and experimental water activities in the ternary system, an empirical modified BET model was selected to represent the thermodynamic properties of this system. The solubility data determined in this work at T = (283.15 and 323.15) K, as well as those from the literature at other temperatures, were used for the model parameterization. A complete phase diagram of the ternary system was predicted over the temperature range from (273.15 to 323.15) K. Subsequently, the Gibbs free energy of formation of the solid phases CaCl₂ · 4 H₂O_(s), CaCl₂ · 2 H₂O_(s), LiCl · 2H₂O_(s), and LiCl · CaCl₂ · 5H₂O_(s) was estimated and compared with the literature data.     

Thermodynamic evaluation and optimization of the (MgCl2 + CaCl2 + MnCl2 + FeCl2 + CoCl2 + NiCl2) system

A complete critical evaluation of all available phase diagram and thermodynamic data has been performed for all condensed phases of the (MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) system, and optimized model parameters have been found. The model parameters obtained for the binary subsystems can be used to predict thermodynamic properties and phase equilibria for the multicomponent system. The Modified Quasichemical Model was used for the molten salt phase, and the (MgCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) solid solution was modeled using a cationic substitutional model with an ideal entropy and an excess Gibbs free energy expressed as a polynomial in the component mole fractions. This is the first of two articles on the optimization of the (NaCl + KCl + MgCl₂ + CaCl₂ + MnCl₂ + FeCl₂ + CoCl₂ + NiCl₂) system.     

High-pressure (vapour + liquid) equilibria for ternary systems composed by {(E)-2-hexenal or hexanal + carbon dioxide + water}: Partition coefficient measurement

A new apparatus based on a static–analytic method assembled in this work was utilised to perform high-pressure (vapour + liquid) equilibria measurements of aqueous ternary systems. This work includes values of isothermal partition coefficients between CO₂ and water of two apple aroma constituents, (E)-2-hexenal and hexanal. Additionally, this work reports new experimental (vapour + liquid) equilibria measurements for the ternary systems (CO₂ + (E)-2-hexenal + water) and (CO₂ + hexanal + water), at fixed liquid phase composition (600 mg · kg⁻¹), at temperatures of (313, 323 and 333) K and at pressures from (8 to 19) MPa. Vapour liquid interphase was checked and monitored visually for all the systems studied in this work. No liquid immiscibility was observed at the composition, temperatures and pressures studied. In order to suggest reasonable operation conditions for fractionation of aromas with dense carbon dioxide, partition coefficients of the aroma compounds between CO₂ and water along with their separation factors from water were calculated. Partition coefficients of (E)-2-hexenal between CO₂ and water were in the range of (6 to 91) and where found to be near six times higher than those of hexanal (9 to 17). Very high separation factors from water were observed (∼10⁴) especially for (E)-2-hexenal. The highest separation factor, for both compounds, was found at a temperature of 313 K and pressures from (12 to 14) MPa.     

Phase equilibrium measurements for semi-clathrate hydrates of the (CO2 + N2 + tetra-n-butylammonium bromide) aqueous solution system

The application of semi-clathrate hydrate formation technology for gas separation purposes has gained much attention in recent years. Consequently, there is a demand for experimental data for relevant semi-clathrate hydrate phase equilibria. In this work, semi-clathrate hydrate dissociation conditions for the system comprising mixtures of {CO₂ (0.151/0.399 mole fraction) + N₂ (0.849/0.601 mole fraction) + 0.05, 0.15, and 0.30 mass fraction tetra-n-butylammonium bromide (TBAB)} aqueous solutions have been measured and are reported. An experimental apparatus which was designed and built in-house was used for the measurements using the isochoric pressure-search method. The range of conditions for the measurements was from 277.1 K to 293.2 K for temperature and pressures up to 16.21 MPa. The phase equilibrium data measured demonstrate the high hydrate promotion effects of TBAB aqueous solutions.     

Thermodynamic evaluation and optimization of the (NaF + AlF3 + CaF2 + BeF2 + Al2O3 + BeO) system

A complete critical evaluation of all available phase diagram and thermodynamic data has been performed for all condensed phases and relevant gaseous species of the (NaF + AlF₃ + CaF₂ + BeF₂ + Al₂O₃ + BeO) system, and optimized model parameters have been found. The (NaF + AlF₃ + CaF₂ + Al₂O₃) subsystem, which is the base electrolyte used for the electro-reduction of alumina in Hall–Héroult cells, has been critically evaluated in a previous article. The Modified Quasichemical Model in the Quadruplet Approximation for short-range ordering was used for the molten salt phase. The thermodynamic database developed is a first step towards a quantitative study of the beryllium mass balance in an electrolysis cell. In particular, the predominant Be-containing species in the gas phase evolved at the anode were identified; and, for a given beryllium content of the alumina, the beryllium content of the electrolytic bath at steady state was assessed under several approximations.