弹道靶开式微波谐振腔测量系统研究

The principle and experimental results of the open microwave resonant cavity measurement system were introduced. The models were steel ball models and the ball models coated with copper. The diameter of the models was 10mm. The models were launched in ballistic range. The model velocity was 5.44 km.s^-1. The wake electron density of the models was obtained. The experimental results presents that the response time of the open microwave resonant cavity measurement system was quicker than 1ms. The results showed the wake electron density ranged from 10⁹cm^-3 to 10¹¹cm^-3 could be achieved.     

HL-2Mװ�ôų���Ȧ��װ��������

用SURFMN和SURFMN_TFCOIL代码计算了由HL-2M装置磁场线圈安装误差产生的误差场。根据国外托克马克装置TF和PF线圈安装误差的取值范围,以及HL-2A装置安装的经验,计算选取的TF线圈和PF线圈最大位移范围为3~8mm,最大倾斜角度为0.05~0.1°。选取9组数据计算了误差场的概率密度分布和累计概率分布。结果发现：在TF和PF线圈安装误差取值范围内,随磁场线圈最大移位增大概率密度显著变平,误差场B3-mode/BT的分布范围显著增大;磁场线圈的位移比倾斜对误差场的影响更大;当磁场线圈最大位移达到5mm时误差场大于2×10-4的概率都比较大,特别是线圈最大位移等于8mm时,误差场大于2×10-4的概率在60%以上。     

HL-2A装置ECRH系统的新天线设计

Using the principle of quasi-optic, the new antenna of the electron cyclotron resonant heating(ECRH) system on the tokamak HL-2A has been designed. After being focused by the elliptical mirror and reflected by the plane mirror, 4 68GHz/500kW/1s electron cyclotron wave beams would be injected into the tokamak from one Æ350mm port to accomplish heating to the plasma. Based on the propagating theory of the fundamental Gaussian beam, it is gotten that at the centre of the cross section of the tokamak, the power density of each beam is 158MW•m^-2, and the power density radius, which means that the power density is reduced by a factor 1/e² compared to the power density at the centre of the beam, is 31.7mm. On the mirror, due to the focusing and reflecting, the ohmic loss and diffraction loss of the microwave beams are 0.27% and 0.64%, respectively. By the finite element analysis software ANSYS, some thermal analysis of the mirror have been done. The result shows that the highest temperature increase would be only 0.47℃ under 1s pulse load, so there is no need of any cooling.     

�����п�ʽ΢��г��ǻ����ϵͳ�о�

介绍了开式微波谐振腔测量系统的工作原理及试验结果,获得了Æ10mm钢球模型在6.65kPa干燥空气中以速度5.44km.s-1飞行时的尾迹电子密度测量结果,并且与国外弹道靶试验数据进行了比较。试验结果表明,该系统能够满足模型尾迹电子密度变化对测量系统响应时间的要求,能很好地反映尾迹电子密度变化细节,电子密度测量范围达到109~1011cm-3。     

�͹���Բ�������������Դ�������о�

介绍了一种低功率圆柱形阳极层离子源的工作特性和束流分布特性。离子源正常工作参数范围为工作电压200～1200V,放电电流0.1～1.4A,工作气压1.9×10-2～1.7×10-1Pa,气体流量5～20sccm。离子源有两个工作状态：发散状态和准直性状态。     

A Two-Field Dilaton Model of Dark Energy

We investigate the cosmological evolution of a two-field model of dark energy, where one is a dilaton field with canonical kinetic energy and the other is a phantom field with a negative kinetic energy term. Phase-plane analysis shows that the ＂phantom＂-dominated scaling solution is the stable late-time attractor of this type of model. We find that during the evolution of the universe, the equation of state w changes from w 〉 -1 to w 〈 -1, which is consistent with recent observations.     

Accurate and rapid error estimation on global gravitational field from current GRACE and future GRACE Follow-On missions

Firstly, the new combined error model of cumulative geoid height influenced by four error sources, including the inter-satellite range-rate of an interferometric laser (K-band) ranging system, the orbital position and velocity of a global positioning system (GPS) receiver and non-conservative force of an accelerometer, is established from the perspectives of the power spectrum principle in physics using the semi-analytical approach. Secondly, the accuracy of the global gravitational field is accurately and rapidly estimated based on the combined error model; the cumulative geoid height error is 1.985× 10^-1~m at degree 120 based on GRACE Level 1B measured observation errors of the year 2007 published by the US Jet Propulsion Laboratory (JPL), and the cumulative geoid height error is 5.825× 10^ - 2~m at degree 360 using GRACE Follow-On orbital altitude 250~km and inter-satellite range 50 km. The matching relationship of accuracy indexes from GRACE Follow-On key payloads is brought forward, and the dependability of the combined error model is validated. Finally, the feasibility of high-accuracy and high-resolution global gravitational field estimation from GRACE Follow-On is demonstrated based on different satellite orbital altitudes.     

Ferromagnetic Properties of Bond-Dilution and Random Positive or Negative Uniaxial Anisotropy Blume-Capel Model

We study the ferromagnetic properties of spin-1 system, which is considered in the frame of the bonddilution and random positive or negative anisotropy Blume-Capel model in the effective field theory and a cutting approximation. The investigation of phase diagrams displays some rich properties of the trajectory of tricritical point,reentrant phenomena at low temperatures. Under certain both bond concentrations and random negative anisotropy,there are new transition lines of double tricritical points. So special emphasis is placed on the influence of the bond dilution and random anisotropy on phase diagrams. The magnetizations of the system are also discussed. Some results have not been revealed in previous reports.     

Tolerance on tilt error for coherent combining of fiber lasers

Limited by the precision of optical machining and assembling, the optical axes of lasers in an array cannot be strictly parallel to each other, which will result in the beam quality degradation of the combined beam. The tolerance on tilt error for coherent combining of fiber lasers is studied in detail. The complex amplitude distribution in the far field for the Gaussian beam with tilt angle is obtained by a novel coordinate transform method. Effect of tilt error on coherent combining is modelled analytically. Beam propagation factor is used to evaluate the effect of coherent combining. Numerical results show that for ring-distributed fiber laser array with central wavelength A and geometry size D, if the root-mean-square （RMS） value of the tilt error is smaller than 0.72A/D, the energy encircled in the diffraction-limited bucket can be ensured to be more than 50% of the value when there is no tilt error. The results are helpful to the designing and manufacturing of fiber array for coherent combining.     

The mixed-spins 1/2 and 3/2 Blume—Capel model with a random crystal field

The random crystal field(RCF) effects are investigated on the phase diagrams of the mixed-spins 1/2 and 3/2 Blume-Capel(BC) model on the Bethe lattice.The bimodal random crystal field is assumed and the recursion relations are employed for the solution of the model.The system gives only the second-order phase transitions for all values of the crystal fields in the non-random bimodal distribution for given probability.The randomness does not change the order of the phase transitions for higher crystal field values,i.e.,it is always second-order,but it may introduce first-order phase transitions at lower negative crystal field values for the probability in the range about 0.20 and 0.45,which is only the second-order for the non-random case in this range.Thus our work claims that randomness may be used to induce first-order phase transitions at lower negative crystal field values at lower probabilities.     

Adjoint and defect error bounding and correction for functional estimates

We present two error estimation approaches for bounding or correcting the error in functional estimates such as lift or drag. Adjoint methods quantify the error in a particular output functional that results from residual errors in approximating the solution to the partial differential equation. Defect methods can be used to bound or reduce the error in the entire solution, with corresponding improvements to functional estimates. Both approaches rely on smooth solution reconstructions and may be used separately or in combination to obtain highly accurate solutions with asymptotically sharp error bounds. The adjoint theory is presented for both smooth and shocked problems; numerical experiments confirm fourth-order error estimates for a pressure integral of shocked quasi-1D Euler flow. By employing defect and adjoint methods together and accounting for errors in approximating the geometry, it is possible to obtain functional estimates that exceed the order of accuracy of the discretization process and the reconstruction approach. Superconvergent drag estimates are obtained for subsonic Euler flow over a lifting airfoil.     

改进内测点测试算法在无线传感网络中的定位研究

在无线传感网络定位算法中,三角形内点测试APIT算法和最佳三角内测点PIT算法受节点密度影响较大,在特定情况下会出现In-To-Out Error 和 Out-To-In Error错误,导致目的节点实际坐标往往与三角重叠区域质心位置相差较远,影响定位精准度。本文提出利用内测点三角成形面积有效检测和避免上述两类错误,并在重叠区域采取指纹分布概率以投票方式计算目的节点坐标。仿真实验证明,新算法受节点密度影响较小,拥有更高的定位精度和准确性。     

GJ-341光电经纬仪视差和反射镜角差的分析与控制

本文介绍了GJ-341小型遥控光电经纬仪双反射镜结构的特点,利用坐标转换的方法分析了GJ-341主摄影十字丝和双反射镜装配角差对设备测量的影响,讨论了该设备与一般经纬仪在外场标校和修正方法上的不同.提出了十字丝投影系统安装在双反射镜之前的建议.     

靶场光电经纬仪多台交会测量的融合处理及其仿真分析

基于两台经纬仪交会测量原理,分析了两台经纬仪交会测量误差;提出了四台经纬仪两两交会测量结果的加权融合处理方法,该方法充分利用了所有测站的测量信息,而且融合测量值误差小于任两台经纬仪的交会误差;最后进行了仿真分析.从仿真结果可以看出,利用该方法可以大大提高空中目标的辨识精度.另外,本方法同样适用于三台或三台以上经纬仪的交会测量问题.     

Error analysis of two-wavelength absorption-based fibre-optic sensors

An error analysis of two-wavelength absorption-based fibre-optic sensors is presented in this paper. A general formulation to express the measurement error and the error induced by the instability of the light power input into the absorbing sample to be measured is derived. Using this formulation, two common and important errors in this type of sensor, temperature fluctuation of light sources and bending optical fibres, are numerically discussed as illustrative examples. The analyses can be applied to both transmission-type and reflection-type absorption-based fibre-optic sensors.     

高速摄影胶片的数据处理及误差控制

本文讨论利用分析系统和计算机系统进行物、象平行,机械系统画面跳动,光学系统校正,画幅选择及读数次数选择五个角度误差计算。     

医用质子加速器注入器7 MeV漂移管直线加速器的设计

 针对质子治癌直线加速器功耗少、长度短的要求,设计了一台工作频率为324 MHz的漂移管型质子直线加速器(DTL)。该DTL把粒子从2.5 MeV加速到7 MeV,功耗为265 kW, 总长1.9 m。横向聚焦采用FODO结构,漂移管内放置永磁铁。提出一种新的束流匹配方案,在射频四极场加速器(RFQ)与DTL之间不设束运线,而是以 DTL入口处的4个单元为匹配段,把RFQ出口处相椭圆匹配到DTL周期结构入口处的相椭圆。 用PARMILA程序对该DTL进行了动力学模拟,结果表明该方案的束流发射度增长很小。     

自模型曲线分辨法校正ICP-AES中谱线重叠干扰——测量误差对结果的影响

本文将自模型曲线分辨方法(SMCR)应用于ICP-AES谱线重叠光谱干扰的校正,并就测量误差对重叠光谱解析结果的影响作了详细的研究和讨论。两谱线的重叠程度越大,随机误差对光谱干扰校正的影响越大。对测量数据作平滑处理。可以减小数据随机误差对结果的影响,但平滑次数增加,将导致光谱图变形,使干扰校正结果产生较大的误差。数据的平滑不能减小光谱偏离加和性的误差。本工作对两条光谱重叠的情况作了讨论,并取得了较好的结果,表明SMCR法是校正ICP-AES中重叠谱线干扰的一种简便、快速的方法。     

Multi-step phase-shifting algorithms insensitive to linear phase shift errors

We describe and analyse a group of multi-step phase calculation algorithms for evaluation of interferometric measurements using the phase-shifting technique. Phase-shifting algorithms are proposed, with a constant but arbitrary phase shift between captured frames of the irradiance of the interference field. The algorithms are similarly derived as so called Carré algorithm. The phase evaluation process is not dependent on linear phase shift errors. An advantage of the described algorithms is their ability to determine the phase shift value at every point of the detector plane. Moreover, a complex error analysis of proposed algorithms is performed and the algorithms are compared to several common error compensating phase stepping algorithms.